Transcript
Stand-Alone Digital Serializer SER-1001-102-x SER-1001-103-x SER-1001-10x-x…………………
Product Description DeCrane Aerospace Audio International's SER-1001-10x-x is a stand-alone Serial Digital Serializer that accepts analog audio and analog video input signals from an external A/V device(s). This unit integrates analog-to-digital conversion and serializer circuitry intended to separately capture and serialize one (1) analog audio source into an AES3 serial digital format, and one (1) analog video source into a standard-definition (SD) serial digital interface (SDI). The SD-SDI video input is compliant to level C of SMPTE 259M standards requirements. Each set of serial digital signals is then routed to either compatible switching or de-serializing devices. The input accepts stereo analog audio along with Composite, Y/C (S-Video), or Y/Pr/Pb (component) video signals. Operation is independent of video standard, capable of operating on the common standards - NTSC, PAL, and SECAM. AES3 audio output is accomplished using 24-bit, 48kHz analog-to-digital conversion of the stereo analog audio. An audio input gain adjustment allows gain selections of 6dB, 0dB, and +10dB to compensate for varying levels of audio source devices. Depicted below, the gain adjustment is located on the side of the unit. The power-up video input standard switching order, i.e. Composite, S-video, Component, is selected via the configuration ID pins. A video select input allows the input standard to cycle in the event the serializer is used to connect to different video types. Only a single standard should be connected at one time, i.e. composite or S-video can be connected at the input, but not at the same time. Three (3) configuration ID pins are used to determine the power-up video standard that is being decoded and the order in which the standard will switch when the video select input becomes active. The “x” in “-10x” designates the varying dimensions of the products; “-102” and “-103”. The “-x” suffix designates the type of connector utilized in installation; “-1” = Positronic and “-2” = D-Subminiature. Features Unit accepts standard analog stereo audio Two (2) Simultaneous AES3 (AES/EBU) outputs Selectable Composite video, Y/C, or Y/Pr/Pb video inputs Two (2) Simultaneous SD-SDI video outputs Lightweight and sturdy design Automatic functionality; no control required No cooling requirements Easy to mount and connect No RS-485 command interface is required for this device.
2.
SER-1001-103-x 3.
4.
1. 2.
3.
5.
6.
Typical audio input interfaces include various audio source equipment. This unit can interface with and accept input from all standard COTS (Commercial-Off-The-Shelf) audio source equipment incorporating the specified interfaces including but not limited to: CD, Cassette, DVD, VCP, VCR and MP3 players as well as Personal Game Systems. Typical audio output interfaces include various audio distribution and/or signal manipulation devices. This unit can interface with and accept input from all standard COTS audio devices and/or equipment incorporating the specified interface including but not limited to: Audio Crosspoint Switchers, Sound Processors, Power Amplifiers and Passenger Headsets (typically used for entertainment purposes).
Typical video input interfaces include various types of video source equipment. This unit is capable of interfacing and accepting input from all standard COTS video source equipment incorporating the specified interfaces including but not limited to: Camcorder, Live-Feed Camera, DVD, VCP and VCR players as well as Moving Map Systems and Personal Game Systems. Typical video output interfaces include various video distribution and/or signal manipulation devices. This unit is capable of interfacing and providing output to all standard COTS video devices and/or equipment incorporating the specified interface including but not limited to: Video Crosspoint Switchers, LCD Display Monitors, and Touch Screen ECU modules.
Installation Guidelines
4.
Application Notes 1.
SER-1001-102-x
7.
Power and ground connections are recommended to use 22 AWG, minimum, wiring in accordance with M22759 or equivalent. Source input analog audio connections and output digital audio connections are recommended to use shielded twisted pair cabling as necessary in accordance with NEMA WC 27500. Both analog video and analog audio cable lengths between the source equipment and the SER-100-10x-x analog inputs should be kept as short possible. The ideal length is right next to source device, with cable length no more than a few inches. Longer analog cable segments degrade performance proportionally. Analog video input and SDI video output are recommended to use shielded coaxial cable V76261 PIC Wire and Cable. Analog audio input and AES3 serial digital output wire connections must be twisted shielded cable with the shield properly grounded to the dedicated pin at the source end to the dedicated pin at the load end. Twisted shielded cable shall be in accordance with NEMA WC 27500. SDI Video Output cable length limitations are 50 meters with up to four (4) interconnects permitted, as long as the connectors do not create in-line impedance (example - the 50 meter video cable can be broken up into five 10 meter segments). In-line connectors must be rated the same characteristic impedance; it must be designed for the cable and installed properly. In the case of V76261 PIC Wire and Cable, the characteristic impedance is 75 . All digital audio Cable impedance must be 110 +/- 10%. Cable length limitations are 100 meters with up to four (4) interconnects permitted, as long as the connectors do not create in-line impedance (example - a 50 meter audio cable can be broken up into five 10 meter segments). In-line connectors shall be rated the same characteristic impedance; it must be designed for the cable and installed properly.
Page 1 of 2 DeCrane Aerospace Audio International • 7300 Industry Drive, North Little Rock, AR 72117 • Phone 501-955-2929 / Fax 501-955-2988 / www.decraneaerospace.com
Stand-Alone Digital Serializer SER-1001-102-x SER-1001-103-x SER-1001-10x-x………………… Technical Specifications Electrical
Audio Interface
Max. Power Requirements Quiescent Power Requirements Operating Voltage Range Audio Input Formats
100 mA @ +28 VDC Typ. Drawings 525910 IR5 525854 IR2
60 mA @ +28 VDC Typ. +18 to +32 VDC Analog Audio
AES3 Serial Digital 2.0 VRMS nominal (0.5 VRMS Minimum, 7.0 VRMS Maximum) Input Impedance 12K-ohm Video AES3 Serial Digital, Interface Y/C (S-Video), or Video Input Formats Y/Pr/Pb (Component), Composite (NTSC, PAL, SECAM) Standard Definition Serial Video Output Format Digital Interface (SD-SDI) 1.0 Vp-p nominal (0.5Vp-p Input Sensitivity Minimum, 1.5Vp-p Maximum) Input Impedance 75-ohm Mechanical Weight Approx. 0.6 lb / 0.27kg SER-1001-102-x Dimensions 3.88" x 3.91" x 1.35" (l x w x h) 9.86 cm x 9.93 cm x 3.43 cm Weight Approx. 0.6 lb / 0.27kg SER-1001-103-x Dimensions 5.94" x 2.94" x 1.30" (l x w x h) 15.09 cm x 7.47 cm x 3.30 cm
Level IR
Audio Output Format
Reference Documents (or latest revision) Description SER-1001-103-x Outline Drawing SER-1001-102-x Outline Drawing
Document # 532215– Revision History Date Description 08/2008 Initial Release
Input Sensitivity
PROPRIETARY NOTICE Despite any copyright notice, this data and information disclosed herein contains confidential, proprietary designs owned by DeCrane Aerospace Audio International. Neither this data nor the data contained herein shall be reproduced, used or disclosed to anyone without the written authorization of DeCrane Aerospace Audio International.
Page 2 of 2 DeCrane Aerospace Audio International • 7300 Industry Drive, North Little Rock, AR 72117 • Phone 501-955-2929 / Fax 501-955-2988 / www.decraneaerospace.com
