Transcript
COPPER-FIN START-UP CHECKLIST Job Name: _____________________________________________
Model Number: ________________________________________
Address: _____________________________________________
Serial Number: ________________________________________
City: _______________________ ST: _______ Zip: ________
Start-up Date: ________________________________________
OVERVIEW Retrofit New Project
water & ELECTRICAL At full fire, read and record -
Inlet Temp: _________________
How many units are installed at this location? Boiler(s) _____________ Water Heater(s)
Outlet Temp: _________________
_____________
Inspect gas pipe, regulator and meter sizing. Is it sized correctly for Btu/Hr requirement? y n
Delta T: _________________
Supply Voltage: _________________
Tot. Amp Draw: _________________ air Pressure
Record in. of water column -
Conventional venting
Outdoor
Is there an inlet gas lockup regulator on the supply?
Y N
If Yes, is it 10’ upstream from the appliance?
Y N
Record in. of water column -
GAS PRESSURE Vlv 1: _______ *Vlv 2: _______ *Vlv 3: _______ *Vlv 4: _______ *Vlv 5: _______ *Vlv 6: _______ Water Temperatures High Limit: _________
Static Pressure: _____________
Stg 1 Diff: _________ *Stg 2 Diff: _________
Left Blower*: _________________
Dynamic Pressure: _____________
Right Blower: _________________
Manifold Pressure: _____________
VENTILATION Air Inlet Dia. (in.): ____________ Air Inlet Material: ____________ Total Eqv. Length (ft.): ____________
COMBUSTION
venting (Select the venting option being used):
Gas Supply Gas Pipe Dia. (in.): _________ Total Eq. Length Gas Piping (ft.): _________
Combustion and Ventilation Openings: Two openings to outside Two ducts from outside One opening to outside Two ducts from interior space Combustion & Vent Louver Openings Clearance between Openings (total sq. in.): (total sq. in.): inlet & outlet (DV): ______________ ______________ ______________ Comments/Corrections needed for air inlet piping, openings or venting: _____________________________________________________ _____________________________________________________ clearances
Measure and record (inches) the service clearances from the nearest obstruction (min. 24” required for service):
Front: __________
L Side: __________ Top: __________
Rear: __________
R Side: __________
Flue Dia. (inches): ____________ Flue Material: ____________ Total Eqv. Length (ft.): ____________
*If Equipped
Low Fire: High Fire: O2 % ______________ ______________ CO ppm ______________ ______________ CO2 %
______________ ______________
Draft Readings
Record in. of water column -
Unit On:
_____________
Unit Off:
_____________
Barometric Dampers properly adjusted?
Y N
This Startup Sheet is for use only by a qualified heating installer/service WARNING ! technician. Refer to the Installation and Operation Manual for your reference.
Have this unit serviced/inspected by a qualified service technician, at least annually. Failure to comply with the above could result in severe personal injury, death, or substantial property damage.
Start-up performed by:
Comments/Corrections needed for service clearances:
Company: ____________________________________________
_____________________________________________________
Name:
____________________________________________
_____________________________________________________
Phone:
____________________________________________
GENERAL JOB NOTES
Start-up approved by:
_____________________________________________________
Company: ____________________________________________
_____________________________________________________
Name:
____________________________________________
_____________________________________________________
Phone:
____________________________________________
Send completed form to: Email:
[email protected]
Internal Use: S/O #: _____________________
Fax:
(615) 882-2963
Routed:
_____________________
Service Dept/Lochinvar 300 Maddox Simpson Pkwy. Lebanon, TN 37090
Tech:
_____________________
Mail:
— The information on this form verifies operation of the Lochinvar product only. — This does not imply other system components or overall system operation is certified. Component and system verification should be performed by the designated commissioning agent or installing contractor.
Save Then Submit Form
App: Denied: CFI-STARTUP REV B
