Transcript
Epson PowerLite Pro Z8000WUNL
INSTALLATION HANDBOOK Lamp and Status Information
Reading the Indicators e projector is provided with the following four indicators that indicate the operating status of the projector.
1
2 3 4
Indicates the operating status.
Indicates the air
Standby condition button is pressed in this condition, projection starts. When the Preparing network monitoring (maximum approx. 20 minutes) or cool down in progress Buttons are disabled while the indicator is Warming up Warm-up time is about 30 seconds. r warm-up is complete, the indicator stops button does not function during warm-up. Projecting
g.
r status.
Indicates the internal temperature status. Indicates the projection lamp status.
Refer to the following table to see what the indicators mean and how to remedy problems that they indicate. , check that the power cable is connected correctly and that the power is being supplied normally. If all indicators are Sometimes, when the power cable is unplugged, the t indicator remains lit for a short period, but this is not a fault.
Indicator is lit or
g red : Lit
Status
Cause
: Flashing:
: O
Remedy or Status
Internal Error
Stop using the projector, disconnect the power cable from the electrical outlet, and contact your local dealer or the nearest address provided in the Support and Service Guide.
Fan Error Sensor Error Cool System Error
Stop using the projector, disconnect the power cable from the electrical outlet, and contact your local dealer or the nearest address provided in the Support and Service Guide.
High Temp Error (overheating)
e lamp turns and projection stops. Wait f nute tes the projector switches to standby mode, so check the following two points. and air exhaust vent are clear, and that the projector is not positioned against a wall. Check that the air If the air lter is clogged, clean or replace it. the points above, stop using the projector, disconnect the power cable from the If the error electrical outlet, and contact your local dealer or the nearest address provided in the Support and Service Guide. When using at an altitude of 1500 m or more, set High Altitude Mode to On. Set Direction to Pointing Down or Pointing Up when the projector is installed to project images downward or upward.
Lamp Error Lamp Failure
Check the following two points. Take out the both lamps and check if they are cracked. Clean the air lter. If it is not cracked t the lamp and turn on the power. If the error continues: Replace the lamp with a new lamp and turn on the power. If the error continues: Stop using the projector, disconnect the power cable from the electrical outlet, and contact your local dealer or the nearest address provided in the Support and Service Guide.
1
INSTALLATION HANDBOOK
Epson PowerLite Pro Z8000WUNL
Lamp and Status Information Status
Remedy or Status
Cause
If it is cracked: Replace it with a new lamp, or contact your local dealer for further advice. If replacing the lamp yourself, be careful to avoid pieces of broken glass (you cannot continue projecting until the lamp is replaced). When using at an altitude of 1500 m or more, set High Altitude Mode to On. Set Direction to Pointing Down or Pointing Up when the projective direction is downward or upward. Filte
Error
Auto Iris Error Cinema Shutter Error Power Err. (Ballast)
Indicator is
Check the following two points. Check that the air and air exhaust vent are clear, and that the projector is not positioned against a wall. If the air lter is clogged, clean or replace it. the points above, stop using the projector, disconnect the power cable from the If the error electrical outlet, and contact your local dealer or the nearest address provided in the Support and Service Guide. Stop using the projector, disconnect the power cable from the electrical outlet, and contact your local dealer or the nearest address provided in the Support and Service Guide.
g or lit : Lit
Status
Status
: Flashing
: O
: Varies according to the projector status
Remedy or Status
Cause High Temp Warning
(
Replace Lamp
e lamp indicated by ashing indicator, lamp 1 or 2, is due for replacement. Replace it with a new lamp. he replacement period has passed, the possibility that the lamp may explode If you continue increases. Replace it with a new lamp as soon as possible. We recommend replacing both lamps together to maintain consistent hue and brightness of projected images.
Lamp Warning Supply System Warning (Ballast)
Check the following two points. Remove the lamp indicated by th Clean the air lter.
Cause
not an abnormality. However, if the temperature rises too high again, projection stops automatically.) Check that the air and air exhaust vent are clear, and that the projector is not positioned against a wall. If the air lter is clogged, clean or replace it.
indicator, lamp 1 or 2, and check if it is cracked.
Remedy or Status If it is not cracked t the lamp and turn on the power. If the error continues: Replace the lamp with a new lamp and turn on the power. If the error continues: Stop using the projector, disconnect the power cable from the electrical outlet, and contact your local dealer or the nearest address provided in the Support and Service Guide. If it is cracked: Replace it with a new lamp, or contact your local dealer for further advice. (Only one lamp is working. Replace the burned-out lamp as soon as possible.). If replacing the lamp yourself, be careful to avoid pieces of broken glass. When using at an altitude of 1500 m or more, set High Altitude Mode to On. Set Direction to Pointing Down or Pointing Up when the projector is installed to project images downward or upward.
No Air Filter Air Flow Sensor Err.
Check that the air is securely installed. e projector automati t detects that there is no air If the error continues even though an air r is installed, the sensor may be defective. Stop using the projector, disconnect the power cable from the electrical outlet, and contact your local dealer or the nearest address provided in the Support and Service Guide.
Low Air Flow
not an abnormality. However, projection stops automatically if th ls any further.) Clean or replace the air ." is displayed. Check the following two points. Check that the air and air exhaust vent are clear, and that the projector is not positioned against a wall. If the air lter is clogged, clean or replace it. If the Low Air Flow continues cleaning the replace the air with a new one. If the error the points above, stop using the projector, disconnect the power cable from the electrical outlet, and contact your local dealer or the nearest address provided in the Support and Service Guide.
Cln. Air Filter Notice
e message "Time to clean the r. Clean or replace the air ." is displayed. Clean the air If the ai is stained yellow with tobacco smoke and cannot be cleaned, replace it with a new one. s or messages regarding "Cln. Air Filter Notice" are displayed only when Cln. Air Filter Notice is set to On, on the s Extended menu.
2
