Transcript
Triple Wardrobe(Product Code AP06)
Step By Step Assembly Instructions Pre-Assembly Preparation 1. Please check the pack contents before attempting to assemble this product.A full checklist of components is given in this leaflet.If any components are missing,please contact the retailer from whom you bought this product. 2. This product is HEAVY,it should be assembled as near as possible to the point of use.TAKE CARE WHEN LIFTING to avoid
personal injury and(or)damage to the product. 3. This product takes approximately 1 HOUR to assemble with 3 PEOPLE.
4. The fitting pack contains SMALL ITEMS which should be KEPT AWAY FROM YOUNG CHILDREN.
5. Read this leaflet in full before commencing assembly. 6. We recommend that you lay a protective cloth on your carpet during assembly,to prevent marking.
Page 1
L
F
E
B
G
J I
L
H
C
D
K
A A
Plinth Base
1
B
LH Side Panel
1 C
D
Door Frame
1
E
Hanging Rail
1 F Top Cornice
1
G
Back Panel
1
H
Shelf
1 I Upright panel
1
J
Hanging Rail
1
K
Shelf
4 L
4
M
Shelf Pins
20 N
Q 16mm Screw(4*16) 26 R T
Middle Door
30mm CSK Screws
Hinge
63 P
3 S
RH Side Panel
Rail supports
1
16mm Screw(3*16) 20
Wedge
2
1 Page 2
Step 1
-Locate the centre upright panel and the side panels onto the plinth base by using six 30mm CSK screws firstly.Then keep the another three 30mm screws. B
Fittings I
N x 6 N x 3
N
C
A
Step 2
-With the aid of an assistant,locate the door frame(D)onto the wardrobe as shown.Secure using 30mm CSK screws.Then pull the frame tightly against the side panels and center panel and secure the frame from the bottom upwards,using the 30mm CSK screws per side inserted through the wooden block,also secure the frame to the unit base using the angled holes provided in the rear of the bottom rail.
Fittings N x 17
N
A
Page 3
Step 3
-With the aid of an assistant,locate the top cornice (F)as shown.Secure using eleven 30mm screws.Also keep the another three 30mm screws.
Fittings N x 11
N x 3
Step 4
N
-Before attaching the back panel(G),move the wardrobe close to the position where it will be used.With uneven floors you may need to lean the wardrobe slightly left or slightly right to ensure that the doors remain squre.With the aid of an assistant,hold the wardrobe in position and secure the back panel to the rear of
the wardrobe.Finally,tighten all twenty-three 30mm screws(N).
N
Fittings N x 23
Page 4
Step 5 -Firstly using the screws position the hinges onto the middle door as shown,then locate the middle door onto the upright side panel.The assembly is now completed.
Fittings T
Q Q x 18
Step 6 -Push fit twenty shelf pins(N)and locate the shelves(H&K)as shown,noting that they are "Notched"at the rear corners.Secure using twenty 16mm
screws(R) for each shelf pin to fix the shelf.Also locate the two hanging rails(E&J) and the hanging rail supports(L).
Fittings L M M x 20
E Q
P x 20
Q x 8 L x 4
J
H
K
Page 5
Step 7
-If necessary,adjust the door hinges as shown.The assembly is now completed.
Page 6
90cm Bedstead(Product Code AP01) 135cm Bedstead(Product Code AP02) 150cm Bedstead(Product Code AP03)
Step By Step Assembly Instructions
Pre-Assembly Preparation
1. Please check the pack contents before attempting to assemble this product.A full checklist of components is given in this leaflet.If any components are missing,please contact the retailer from whom you bought this product. 2. This product is HEAVY,it should be assembled as near as possible to the point of use.TAKE CARE WHEN LIFTING to avoid personal injury
and(or)damage to the product. 3. This product takes approximately 45 MINUTES to assemble with 2 PEOPLE.
4. The fitting pack contains SMALL ITEMS which should be KEPT AWAY FROM YOUNG CHILDREN.
5. Read this leaflet in full before commencing assembly. 6. You will require a crosshead screwdriver,an open ended spanner. Page 1
A
F
C
D B
E
C
F
A
Headboard
1
B
D
Centre Rail
1
E
Footboard Centre Rail Support
1
C
Side Rail
1
F
Slat
135cm bedstead
150/180cm bedstead
G
Thread
8
H
Nut Washer
8
I
34
(Provided with slats)
150/180cm bedstead
Spanner
32
Plastic Cap 135cm bedstead
J
2
64 68
1
Page 2
Step 1
-Screw the eight threads into the headboard and footboard and tighten by hand.Ensuring that there is enough thread remaining for attachment in step 2 and 3.
Fittings
G
A
G x 8
B
Step 2
-Locate the side rails onto the threads protruding from the headboard.Locate the washer and nut onto the threads and secure
by hand at first.Tighten using the open ended sapnner.
Please note.
The holes in the slat support rail should be facing upwards.
H Fittings
C H x 4
C Page 3
Step 3 -Locate the side rails onto the threads protruding from the footboard.Locate the washers and nuts onto the threads and secure
by hand at first.Tighten using the open ended spanner.
Fittings
A
H
H x 4
B
Step 4 -Attach the centre rail support to the centre rail as follows.
D
E
Page 4
Step 5
-Locate the centre rail into the bottom rail of headboard and
footboard.Also adjust the centre foot as shown.
A
D
E D E
B
Step 6 -Push fit two plastic caps onto either end of the slat.Push fit the slat into the pre-drilled pilot holes.Please note that it may require a light tap with a soft hammer to secure the plastic end caps into the holes.Repeat this step with the remaining slats.The assembly is now completed.
Fittings
135cm bedstead
I x 64
150/180cm bedstead
I x 68
F I
Page 5
Double Wardrobe(Product Code AP05)
Step By Step Assembly Instructions Pre-Assembly Preparation 1. Please check the pack contents before attempting to assemble this product.A full checklist of components is given in this leaflet.If any components are missing,please contact the retailer from whom you bought this product. 2. This product is HEAVY,it should be assembled as near as possible to the point of
use.TAKE CARE WHEN LIFTING to avoid personal injury and(or)damage to the product. 3. This product takes approximately 1 HOUR to assemble with 3 PEOPLE. 4. The fitting pack contains SMALL ITEMS which should be KEPT AWAY FROM YOUNG CHILDREN. 5. Read this leaflet in full before commencing assembly. 6. We recommend that you lay a protective cloth on your carpet during assembly,to prevent marking. Page 1
B
I
E
F
面板
G C H D
A
A
Plinth Base
1
B
LH Side Panel
1 C
D
Door Frame
1
E
Hanging Rail
1 F Top Cornice
1
G
Back Panel
1
H
Shelf
1 I
2
4
K
J
Shelf Pins
M 16mm Screw(4*16) 4
30mm CSK Screws
N Wedge
48 L
RH Side Panel
Rail supports
1
16mm Screw(3*16) 4
2
Page 2
Step 1
-With the aid of an assistant,locate the side panels(B&C)into the plinth base(A),noting that the battens on the side panels should be to the rear.Secure using six 30mm screws.Inserted at an angle through the rear edges of the panels.
B Fittings
K x 6
C L
A
Step 2
-With the aid of an assistant,locate the door frame(D)onto the wardrobe as shown.Pull the frame tightly against the side panels and secure the
frame from the bottom upwards,using five 30mm screws(K) per side inserted through the wooden block.Also Using the 30mm screws secure the frame to the unit base using the angled holes provided in the rear of the bottom rail.
Fittings
D K x 16
L
Page 3
Step 3
-With the aid of an assistant,locate the top cornice (F)as shown.Secure using ten 30mm screws.
F Fittings
K x 10
K
Step 4
-Before attaching the back panel(G),move the wardrobe close to the position where it will be used.With uneven floors you may need to lean the wardrobe slightly left or slightly right to ensure that the doors remain square.With the aid of an assistant,hold the wardrobe in position and secure the back
panel to the rear of the wardrobe.Finally,tighten all sixteen 30mm screws(K).
Fittings
K
K x 16
Page 4
-Push fit four shelf pins(J)and locate the shelves(H)as shown,noting
Step 5
that they are "Notched"at the rear corners.Secure using four 16mm
screws(L) for each shelf pin to fix the shelf.Also locate the hanging rails(E) and the hanging rail supports(I).
I
Fittings
J J x 4 L x 4
E
M
M x 4 I x 2
H
Page 5
90cm Bedstead(Product Code AP01) 135cm Bedstead(Product Code AP02) 150cm Bedstead(Product Code AP03) 180cm Bedstead(Product Code AP04)
Step By Step Assembly Instructions
Pre-Assembly Preparation
1. Please check the pack contents before attempting to assemble this product.A full checklist of components is given in this leaflet.If any components are missing,please contact the retailer from whom you bought this product. 2. This product is HEAVY,it should be assembled as near as possible to the point of use.TAKE CARE WHEN LIFTING to avoid personal injury
and(or)damage to the product. 3. This product takes approximately 45 MINUTES to assemble with 2 PEOPLE.
4. The fitting pack contains SMALL ITEMS which should be KEPT AWAY FROM YOUNG CHILDREN.
5. Read this leaflet in full before commencing assembly. 6. You will require a crosshead screwdriver,an open ended spanner. Page 1
A
F
C
D B
E
C
F
A
Headboard
1
B
D
Centre Rail
1
E
Footboard Centre Rail Support
1
C
Side Rail
1
F
Slat
135cm bedstead
150/180cm bedstead
G
Thread
8
H
Nut Washer
8
I
34
(Provided with slats)
150/180cm bedstead
Spanner
32
Plastic Cap 135cm bedstead
J
2
64 68
1
Page 2
Step 1
-Screw the eight threads into the headboard and footboard and tighten by hand.Ensuring that there is enough thread remaining for attachment in step 2 and 3.
Fittings
G
A
G x 8
B
Step 2
-Locate the side rails onto the threads protruding from the headboard.Locate the washer and nut onto the threads and secure
by hand at first.Tighten using the open ended sapnner.
Please note.
The holes in the slat support rail should be facing upwards.
H Fittings
C H x 4
C Page 3
Step 3 -Locate the side rails onto the threads protruding from the footboard.Locate the washers and nuts onto the threads and secure
by hand at first.Tighten using the open ended spanner.
Fittings
A
H
H x 4
B
Step 4 -Attach the centre rail support to the centre rail as follows.
D
E
Page 4
Step 5
-Locate the centre rail into the bottom rail of headboard and
footboard.Also adjust the centre foot as shown.
A
D
E D E
B
Step 6 -Push fit two plastic caps onto either end of the slat.Push fit the slat into the pre-drilled pilot holes.Please note that it may require a light tap with a soft hammer to secure the plastic end caps into the holes.Repeat this step with the remaining slats.The assembly is now completed.
Fittings
135cm bedstead
I x 64
150/180cm bedstead
I x 68
F I
Page 5
