Preview only show first 10 pages with watermark. For full document please download

Stereo Dab+/fm Radio

Rating
Date

September 2018
Size

2.4MB
Views

8,077
Categories

Computers & electronics Audio & home theatre Radios

Transcript

Stereo DAB+/FM Radio Contents Where to put your radio�� 3 Setting up�� 3 Your Stereo DAB+ / FM radio �� 5 Using your DAB+ radio�� 6 Switch on�� 6 Switch off�� 6 Adjusting the volume�� 6 Changing DAB+ stations �� 6 Scanning for DAB+ stations �� 6 Manual tune�� 7 Storing a DAB+ station preset �� 7 Tune to a DAB+ preset station�� 8 DAB+ display information �� 8 Using the FM radio�� 9 FM radio mode �� 9 Tuning to an FM station�� 9 Storing an FM station preset�� 9 Tune to an FM preset station ��10 FM display information��10 Using the alarm��11 To set an alarm��11 When the alarm sounds��11 To cancel an alarm��11 Technical information��12 Specification��12 Software version��12 Reset your radio ��12 Simple solutions��13 General information��14 Care and maintenance��14 Consumer product warranty ��15 2 Product Set Up Step 3: Press the ‘Power’ button on the front of the radio. The ﬁrst time you switch your radio on it will automatically begin to scan for DAB+ radio stations. A progress bar will show the progress of the scan and the number of stations found during the scan will also be displayed. Where to put your radio It is important that you consider carefully in advance where your radio will be situated and make sure that it is: * on a ﬂat and stable surface * within 1.8 metres of a power socket When the scan is complete your radio will select the ﬁrst available station and begin to play. Stations are listed in numerical and then alphabetical order by default. * where you can fully extend the telescopic aerial * away from bright sunlight or heat sources, such as a radiator * not in a humid or very damp place such as a bathroom Note: The DAB+ radio station list is stored in the memory and so the next time you switch your radio on, the station search does not take place. It is possible to scan manually for stations. Please see page 6. Setting up Step 1: Connect the mains power lead into the socket on the bottom left of the back of the radio and fully extend the radio aerial in a vertical position to obtain the maximum signal strength. Step 4: Inserting the batteries (optional). Before installing the batteries (not included) please ensure that the Radio is unplugged from the mains power supply. Note: Only use the power supply provided. Using an unauthorised power supply will invalidate your warranty and may damage your radio. On the back of the radio, push the two tabs on the battery compartment down and remove the battery cover. Insert 4 x 1.5V LR14 C-size batteries, making sure to note the ‘+’ and ‘-‘ markings and position the batteries the correct way around. Replace the battery cover, making sure it ‘clicks’ shut. Step 2: Plug the power adaptor into the mains power wall socket and switch on. ‘Welcome to Digital Radio’ will be displayed. 3 Note: For battery operation, please switch oﬀ the mains adaptor and remove the mains power plug from the back of the radio. • Only use the recommended batteries or those of the same equivalent type. • Do not mix old and new batteries or batteries of diﬀerent types. • Batteries are to be inserted with the correct polarity. • The supply terminals are not to be short-circuited. • Remove the batteries from the radio if they will not be used for an extended period of time. • Do not attempt to recharge non-rechargeable batteries. • Dispose of old batteries carefully. • Never throw batteries in a ﬁre or attempt to open the outer casing. • Batteries are harmful if swallowed, so keep away from young children. • Batteries must not be exposed to excessive heat such as sunshine or ﬁre. • CAUTION: Danger of overheating or ﬁre if batteries are incorrectly replaced. Replace only with the same or equivalent type. 4 Your Stereo DAB+ / FM Radio Carry handle Backlit display Rotary volume control Telescopic aerial (at rear) Rotary tune control Push to select Power Memory buttons Scan Menu Preset Info. DAB+/FM mode Alarm Mains power socket (at rear) Stereo speakers 5 Battery compartment (at rear) Using your DAB+ Radio Switch on Changing DAB+ stations Press the ‘Power’ button on the front of the radio. The display will switch on and your radio will return to the mode that it was last used in (DAB+ or FM). If you were listening to a DAB+ station before then this station will be automatically selected. 1. If you are not already in DAB+ mode, Press the ‘DAB/FM’ button to go to DAB+ mode. 2. Turn the right hand ‘Tune’ rotary control to scroll through the available stations. Stop when the station you like to listen to is displayed and your radio will tune to that station. Note: Always make sure that the aerial is fully extended and adjusted (a vertical position is recommended), to ensure the maximum signal strength and the best possible sound quality. Scanning for DAB+ stations With DAB+ radio, additional stations and services regularly become available so it’s a good idea to carry out a manual scan every now and then to make sure that you have the most up to date station listing stored within the memory of your radio. If you have moved your radio to another location, eg: if you go on holiday, then it’s also a good idea to carry out a manual scan. Switch oﬀ Press the ‘Power’ button on the front of the radio, the clock will be displayed. To completely switch oﬀ the radio and the display, switch oﬀ the mains power socket. 1. If you are not already in DAB+ mode, press the ‘DAB/FM’ button to go to DAB+ mode. Adjusting the volume Turn the left hand ‘Volume’ rotary control anti-clockwise to decrease the volume and clockwise to increase the volume. 6 Note: You may need to adjust the aerial or move your radio to get the strongest possible signal. 2. Press the ‘Scan’ button to begin a local search for stations. The display will change to ‘Autotune Quick scan’, followed by ‘Searching...’. A progress bar will show the progress of the scan and the number of stations found during the scan will also be displayed. A local scan takes approximately 10 seconds. 3. Press the rotary ‘Tune’ control to display the radio text for the frequency that you have selected. ‘MAN’ will also be displayed in the top right of the display to remind you that you are in Manual tune mode. 3. Press and hold the ‘Scan’ button for 2 seconds to begin a wider, national and local scan. The display will change to ‘Autotune Full scan’, followed by ‘Searching...’. A progress bar will show the progress of the scan and the number of stations found during the scan will also be displayed. A national and local scan takes approximately 1 minute but can take up to 3 minutes. 4. Press the rotary ‘Tune’ control again to return to DAB+ autotune mode. ‘DAB’ will be displayed in the top right of the display. Storing a DAB+ station preset Your radio can store up to 10 DAB+ stations in its preset memories for instant access to your favourite stations. Note: When you store DAB+ radio station presets, these do not overwrite your FM station presets. Manual tune Using the manual tune feature you can select a speciﬁc digital radio channel frequency and then manually adjust the aerial, or the location of the radio, to get the strongest possible signal for that channel in your location. 1. Tune your radio to the station that you wish to preset (see changing DAB+ stations, page 6). 2. Press and hold the ‘Preset’ button. Preset location 1 will be displayed. 1. Press and hold the rotary ‘Tune’ control until ‘Manual tune’ is displayed. 3. Turn the rotary ‘Tune’ control to the preset location that you would like to store the radio station to (1-10). Press the ‘Tune’ control to save the station to the displayed preset location. The display will conﬁrm ‘Preset X stored’, where ‘X’ is the number of the preset location (1-10). 2. Turn the rotary ‘Tune’ control to scroll through the digital radio frequencies. Stop when the frequency you would like to listen to is displayed and your radio will then attempt to tune to that frequency. ‘Tuning...’ will be displayed. 7 Note: If there is already an existing DAB+ station stored under a preset location, it will be over written when you store the new station. Tune to a DAB+ preset station In DAB+ mode: DAB+ display information When listening to a DAB+ station you can change the information that will appear on the second line of the display. There are several different types of information that are sent by the broadcaster. Dynamic Label Segment (DLS) - this is scrolling text information supplied by the broadcaster. Information could be the name of an artist or music title, DJ’s name, contact details for the radio station etc. Program Type (PTY) - such as ‘Rock’, ‘Pop‘, Talk’ or ‘News’ Multiplex Name - displays the broadcasting area and collection of radio stations on this frequency eg: BBC National DAB, Digital 1 Network. Signal Strength - An empty will appear on the second line of the display to indicate the minimum signal strength for acceptable listening. The row of solid rectangles indicate the actual signal strength that you are receiving. The stronger the signal, the further to the right the row of solid rectangles will be. Time - supplied by the broadcaster. Channel and Frequency - eg: 12B 225.64 MHz Signal Information - Stereo or Mono and the data rate at which the signal is being transmitted. 1. Press the ‘Preset’ button. Preset location 1 will be displayed. 2. Turn the rotary ‘Tune’ control to display the preset location (1-10) that you would like to select. Press the ‘Tune’ control. The radio will instantly tune to the stored station and begin to play. Alternatively, for preset locations 1, 2 and 3, you can simply press the ‘1’, ‘2’ or ‘3’ button on the front of the radio for quick and fast access to stations stored there. Note: If no DAB+ station has been stored under a preset location, ‘Preset Empty X’ is displayed and after a few seconds the display will revert to the previously selected station. 1. Press the ‘Info’ button repeatedly to move through the display options. 8 Using the FM Radio Note: With FM radio it may be necessary to ‘ﬁne tune’ each station by turning the ‘Tune’ control. If reception is still poor adjust the position of the aerial or try moving the radio to another location. FM Radio Mode Check that your radio is in FM mode. You will see ‘FM’ to the far right of line 1 of the display together with a radio frequency eg: 89.60MHz. Storing an FM station preset When your radio is in FM mode it can receive Radio Data System or ‘RDS’ information if this is being transmitted by the broadcaster. RDS information will often include the station name, detail about the programme and the current time. Your radio can store up to 10 FM stations in its preset memories for instant access to your favourite stations Note: When you store FM radio station presets, these do not overwrite your DAB+ station presets. If you were listening to an FM station when you switched the radio oﬀ then this station will be automatically selected when you switch the radio back on. 1. Tune your radio to the station that you wish to preset (see Tuning to an FM station on this page). 2. Press and hold the ‘Preset’ button. Preset location 1 will be displayed. Tuning to an FM station 1. If you are not already in FM mode, press the ‘DAB/FM’ button to go to FM mode. 3. Turn the rotary ‘Tune’ control to the preset location that you would like to store the radio station to (1-10). Press the ‘Tune’ control to save the station to the displayed preset location. The display will conﬁrm ‘Preset X stored’, where ‘X’ is the number of the preset location (1-10). 2. Press the ‘Scan’ button. The Radio will scan until it ﬁnds the next station where it will stop and show the frequency, or RDS information, if it is available. Note: If there is already an existing FM station stored under a preset location, it will be over written when you store the new station. 9 Tune to an FM preset station FM display information In FM mode: When listening to an FM station you can change the information that will appear on the second line of the display. There are six different types of information that are sent by the broadcaster. 1. Press the ‘Preset’ button. Preset location 1 will be displayed. 2. Turn the rotary ‘Tune’ control to display the preset location (1-10) that you would like to select. Press the ‘Tune’ control. The radio will instantly tune to the stored station and begin to play. Dynamic Label Segment (DLS) - this is scrolling text information supplied by the broadcaster. Information could be the name of an artist or music title, DJ’s name, contact details for the radio station etc. Program Type (PTY) - such as ‘Rock’, ‘Pop‘, Talk’ or ‘News’ Signal Strength - An empty will appear on the second line of the display to indicate the minimum signal strength for acceptable listening. The row of solid rectangles indicate the actual signal strength that you are receiving. The stronger the signal, the further to the right the row of solid rectangles will be. Time - supplied by the broadcaster. Frequency - eg: 89.60 MHz Signal Information - depending on the quality of the signal the radio will automatically switch between ‘Stereo’ and ‘Mono’. When ‘Auto’ or ‘Mono’ is displayed, press the rotary ‘Tune’ control to switch between each mode. Alternatively, for preset locations 1, 2 and 3, you can simply press the ‘1’, ‘2’ or ‘3’ button on the front of the radio for quick and fast access to stations stored there. Note: If no FM station has been stored under a preset location, ‘Preset Empty X’ is displayed and after a few seconds the display will revert to the previously selected station. 1. Press the ‘Info’ button repeatedly to move through the display options. 10 Using the Alarm You can set an alarm on your radio when it is switched on or in ‘Standby’ mode. You can choose to wake to a buzzer or to a DAB+ or FM radio station. When the alarm sounds 1. Press the ‘Alarm’ button once to stop the alarm. To set an alarm To cancel an alarm 1. Follow the steps ‘To set an alarm’ on this page and select ‘OFF’ at step 2. 1. Press the ‘Alarm’ button. ‘OFF’ will flash in the display. 2. Turn the rotary ‘Tune’ control to display ‘ON’ or ‘OFF’ and press the ‘Tune’ control to select ‘ON’. ‘00’ will flash in the display. 3. Turn the ‘Tune’ control to set the hour for your alarm and press the ‘Tune’ control to select. ‘00’ will flash in the display. 4. Turn the ‘Tune’ control to set the minutes for your alarm and press the ‘Tune’ control to select. ‘Alarm1 Type’ is displayed. 5. Turn the ‘Tune’ control to choose to wake to a buzzer or to DAB+ or FM radio and press the ‘Tune’ control to select. Note: If you select to wake to DAB+ or FM radio, the alarm will use the last DAB+ or FM station that the radio was tuned to. 6. When you turn the radio off a small bell symbol will be displayed in the top right of the display to confirm that an alarm has been set. 11 Technical Information Specification Power adaptor: Output: Batteries: You can reset your radio and restore all of the original factory Output DC 6V 1A Input AC 100-240V/50-60Hz 2 x 2W RMS 4 x 1.5V LR14 C-size (optional, not supplied) Frequency range: DAB+ Band III, 174 MHz to 240 MHz FM 87.5 MHz to 108 MHz Software version To check the software version of your radio Reset your radio settings. ote: If you reset your radio all of your DAB+ and FM station N presets and alarm settings will be deleted. 1. Press and hold the ‘DAB/FM’ button. ‘Press Enter Key to Reset’ will be displayed. 2. Press the rotary ‘Tune’ control. ‘System reset’ will be displayed, followed by ‘OK’. The radio will now reset and then automatically begin to scan for DAB+ radio stations. A progress bar will show the progress of the scan and the number of stations found during the scan will also be displayed. 1. Press the ‘Menu’ button. The software version will be displayed. 12 Simple Solutions If you are experiencing problems with your radio there are some quick and easy checks that you can do, which may help to solve the problem. Radio reception is poor - Please check that the aerial is FULLY extended for the maximum signal strength and improved reception. - Adjust the volume using the rotary ‘Volume’ control. The function buttons do not respond - Check that the power lead is plugged into the back of the radio and that the mains adaptor is plugged in and switched on. Press the ‘Power’ button on the front of the radio. - - Visit www.digitalradioplus.com.au for information about DAB+ reception in your area. No sound - Turn off the radio and unplug the mains power. Leave for 1 minute and then reconnect your radio. Check that you do not have other electrical equipment too close to your radio, causing interference. You may need to re-scan if the station you last listened to is no longer available. See page 6. - If you are using batteries, they may be exhausted and need to be replaced. - Try moving your radio to an alternative location to see if the reception improves. Please remember to scan for DAB+ stations again once you have moved your radio. See page 6. - - - Please check that the mains power lead is connected at the back of the radio and the mains power wall socket is switched on. - If you are using batteries, they may be exhausted and need to be replaced. 13 Try a reset to factory defaults. See page 12 General Information Care and Maintenance - Your radio is of superior design and manufacture and should be treated with care. The suggestions below will help you to enjoy this product and the benefits it brings for many years. - Keep the product and all its parts out of reach of small children. - Keep it dry. Avoid exposure to precipitation, humidity and liquids which could all affect the product circuitry. - Do not leave it in high temperatures as electronic devices and plastic parts may warp in heat. - Do not leave it in low temperatures as moisture can form inside the product, which may damage the circuit board. - Do not store in dusty or dirty areas. - Do not use harsh chemicals, cleaning solvents or detergents to clean the product. Wipe with a damp (not wet) soft cloth to clean. - Do not attempt to open the product. Unauthorised handling of the device may damage it and will void your warranty. 14 Only use the power supply that came with the product. Using an unauthorised power supply will invalidate your guarantee and may irrecoverably damage the radio. Consumer Product Warranty Australia & New Zealand Standard Warranty For Magicbox Products Consumer Product Warranty (Warranty against Defects) 1.2 Subject to the above, as part of your Standard Warranty Canohm agrees to repair or replace at Canohm’s cost the goods (which includes a supplied Magicbox accessory) purchased by you in Australia or New Zealand from a Magicbox Authorised Dealer when the good does not perform in accordance with the manufacturer’s specifications during the Warranty Term specified below, commencing from the date of purchase. The purchase of a Magicbox product (hereinafter referred to in this Standard Warranty as “good(s)”) includes coverage by the Magicbox Standard Warranty. The Magicbox Standard Warranty is provided by: Standard Radio Distributors trading as Canohm (ABN 57 004 817 949), 3/200 Turner Street, Port Melbourne, Victoria 3207 Australia. Ph: 03 9644 7888, Email: [email protected] 1.3 Goods returned for repair may be modified or repaired with refurbished parts of the same type. Replacement of the good or a part does not extend or restart the Warranty Term. Warranty terms and conditions 1.4 In the case of a good presented for repair which is capable of retaining user-generated data (e.g. internal memory), you are advised that the repair process of the good may result in loss of that data. 1.1 Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure. The benefits provided in this Standard Warranty are in addition to other rights and remedies you may have under law. 1.5 The good will be at the owner’s risk whilst in transit to and from the Canohm Authorised Service Centre, unless transported by Canohm or its Authorised representatives. 1.6 Transportation of the good to Canohm or its Service Centre is at your cost. Canohm will not be liable for any damage caused to the good whilst in transit. 15 1.7 The cost of repair or replacement of the good shall be at Canohm’s cost but Canohm and its Authorised Service Centres may seek reimbursement of any costs incurred by them when the good is found to be in proper working order. (d). To damage arising out of or during transportation, installation or while moving the good, or to any transportation costs of the good or any parts thereof to and from the owner, unless otherwise specified in these warranty terms. (e). To any third-party software or hardware not contained in the good as originally configured by the manufacturer. (f ). To any failure, to the extent that the failure is not a failure of the good to perform in accordance with its specifications. (g). To replacement or repair of any: General exclusions and limitations 2.0 To the full extent permitted by law, but subject always to clause 1.1, the Standard Warranty will not apply: (a). If the good has not been installed, operated, maintained or used in accordance with the manufacturer’s instructions or specifications provided with the good. (b). If the serial number has been altered or removed from the good. (c). To damage as a result of malfunction or failure resulting from alterations, accident, misuse, abuse, fire, liquid spillage, faulty or mis-adjustment of customer controls, use on an incorrect voltage, voltage supply problems, power surges and dips, thunderstorm activity, acts of God, tampering or unauthorised repairs by any persons, use of defective or incompatible accessories, the operation of a computer virus of any kind, exposure to conditions that are known to cause damage or entry by any foreign object in the good. (I). (II). lost parts or accessories. (h). To service of any good whilst it is outside Australia and New Zealand. (i). To any wear and tear if the good is used in commercial, industrial, educational or rental applications. 16 consumables (including batteries and cables), or (j). If DAB+ (Digital Radio) broadcast is not received: (I). due to unreasonable/unusual environmental factors such as in tunnels (e.g. rail or road), underground, or in buildings or other structures whose location or method of construction prevents a DAB+ radio from receiving a DAB+ signal, or 4.0 To make a claim under the Standard Warranty you will need to: (II). where the receivers are being used in areas which are “not covered” by DAB+ broadcasts. (In Australia refer to Commercial Radio Australia’s website www.digitalradioplus.com.au for current reception areas.) 3.0 To the full extent permitted by law but subject always to clause 1.1: (a). Canohm will not be liable for any loss, damage or alterations to: (I). third party hardware or software; or (II). programs, data or information stored on any media or any part of the good, no matter how occurring; or for any loss or damage arising from loss of use, loss of profits or revenue, or for any resulting indirect or consequential loss or damage. Making a Claim (a). Contact Canohm (contact details below) to notify your claim and provide sufficient details to enable Canohm to assess the claim. In order to assist with this process you may visit the Support section located on the Magicbox website. (b). Provide or make the good available to Canohm or a Canohm Authorised Service Centre. If you are required to return the good to a Canohm Authorised Service Centre, Canohm will provide details of the centre to you. (c). Provide proof of purchase of the good(s) (e.g. invoice or purchase receipt) at the time of making your claim (unless not required by law). All Magicbox Products have a 1 year warranty. 17 For further details or to find your nearest Magicbox Authorised Service Centre please contact: Australia Toll Free on 1800 636 026 Web: www.magicboxaudio.com.au or email [email protected] New Zealand Toll Free on 0800 486 435 Web: www.magicboxaudio.co.nz or email: [email protected] 18 Issue 1/Jul13

Stereo Dab+/fm Radio

Rating

Date

Size

Views

Categories

Share

Transcript

Forgot your password?.