Transcript
Installation and Operation Manual
STI REPEATER Model: STI-34109
Thank you for purchasing this fine product. Your satisfaction is very important to us. Please read this manual carefully to get the most from your new product.
HOW THE PRODUCT WORKS
STI offers wireless products designed to alert you of several different conditions. The STI REPEATER is a 433 MHz radio signal receiver and transmitter that effectively doubles the transmission range of STI sensors to STI receivers. The REPEATER will filter out all radio signals that are not using 433 MHz STI protocol. When any STI protocol signal packet (except STI 8-Channel Receiver) is received, it transmits the same signal packet. There is no limit to the number of STI sensors that may be used with the STI REPEATER. It should be understood that multiple REPEATERS should NOT be used within reception range of each other because a REPEATER will simply retransmit any STI protocol signal packet (except 8-Channel Receiver). Two REPEATERS within reception range of each other can retransmit signal packets back and forth a few times when sensor packet is received. If a dual REPEATER system or further extended range applications are needed, please purchase STI 8-Channel Receivers (STI-34108). The receivers will retransmit alert and trouble notifications of the sensor signals, but not the actual signals themselves. Therefore, REPEATER feedback will not occur. The receivers work with up to 8 different STI wireless sensors.
BEFORE YOU START
Refer to this drawing to become familiar with all the parts.
FEATURES
• Extends system range. • Receives and retransmits distant STI protocol wireless device signals (except for STI 8-Channel Receivers signals) to receivers. • Sensor reprogramming not required. • All STI protocol alarm, supervisory and trouble signals are repeated to receivers. • REPEATERS have their own unique ID for supervisory, tamper alert and low battery signals that can be monitored with receivers. • Antennas increase range for both reception and transmission of signals. • Backup battery protects during loss of external power (up to 72 hours).
SPECIFICATIONS
• External Supply: 9-18V AC or DC, 15 mA nominal (recommended 30+ mA rating). • Three (3) 1.5V AAA Alkaline batteries: external power backup (up to 72 hours). • Housing Dimensions: 4 x 6 3/8 x 1 ¼ in. • Antenna length when inserted in housing: 7 ¾ in.
OPERATION
The REPEATER receives distant STI protocol sensor signals and repeats the information to the receiver. Generally, STI sensors send 8 identical signal “packets” of information. The REPEATER rejects any signal that is not an STI protocol packet and retransmits the complete 8 packet set to the receiver.
STI REPEATER’S wireless signals
• Tamper Signal – tamper switch released when cover is opened or damaged • Tamper Restore Signal – tamper condition corrected • Low Battery Signal – battery charge low • Low Battery Restore Signal – low battery condition corrected • Supervisory Signal – sent every hour to monitor that REPEATER is within range
REPEATER and sensor enrolling
• The receiver can monitor the REPEATER’S supervision and trouble signals when they are enrolled (if desired). • To manually send a REPEATER signal, press and release the tamper switch. Ensure the red LED blinks. • To enroll sensors, follow the receiver’s programming instructions.
LEDS
ON BLINKING
GREEN LED
AC/DC power on
Signal Received
RED LED
Low Battery Alert (only with AC/DC power on)
Signal Transmitted
—2—
INSTALLATION GUIDE
The REPEATER is intended to be mounted indoors or in a waterproof environment. Review the APPLICATIONS GUIDE for suggested setups.
1. Press the cover latch to remove top cover (do not lose tamper switch spring). 2. Remove the PCB from bottom cover. Using the keyholes on the bottom cover as a template, mark the top and bottom mounting holes. Locate the hole at least 1 foot away from the closest obstruction above. 3. Drill 3/16” holes. 4. Insert wall anchors, screws and washers (provided) and tighten to 1/8” gap. 5. TURN OFF POWER SUPPLY. Route power supply wires from the side (recommended) or hole from the back. a. Side installation – route wires through right wire guide and then left wire guide. Remove knockout on the top cover. b. Rear installation – run wires through back wire guide and then left wire guide. 6. Place bottom cover keyholes onto screws and orient device vertical. 7. Tighten screws. 8. On the PCB, insert the antennas into the outer antenna terminals marked “ANTENNA.” Tighten the antenna terminal screws. 9. Snap PCB into bottom cover so the antennas are on the plastic stands. 10. Remove the battery tab. The red LED blinks when the batteries are installed. If LED does not blink, press and release the tamper switch. If LED still does not blink, replace batteries. 11 .Insert 12 Volt AC or DC power supply leads into the terminals marked “AC/DC 12V.” The positive and negative terminals have interchangeable polarity. They may be oriented either +/- or -/+. 12. Turn on the power supply. The green LED turns on. If the red LED is on, replace the 3 AAA Alkaline batteries. 13. (If desired) Program the REPEATER and/or the sensors into the receiver (follow the receiver programming instructions). The receiver can monitor the REPEATER’S supervision and trouble signals when enrolled. To manually send a REPEATER signal, press and release the tamper switch. The red LED blinks when transmitting. 14. If the REPEATER or the sensors do not program properly, move the REPEATER mounting location closer to the receiver. 15. Latch the top cover in place. Ensure the power supply wires are routed properly.
IMPORTANT NOTICE
Information and specifications are subject to change without notice. This product has been tested and complies with the specifications for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used according to the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which is found by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna - Increase the separation between the equipment or devices - Connect the equipment to an outlet other than the receiver’s - Consult a dealer or an experienced radio/TV technician for assistance Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Changes or modifications not expressly approved by Safety Technology International, Inc. could void your authority to operate this equipment. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotopically radiated power (e.i.r.p.) is not more than that permitted for successful communication. This product meets the applicable Industry Canada technical specifications. Le présent materiel est conforme aux specifications techniques applicables d’Industrie Canada. FCC ID: U5X-RE324 IC: 8310A-RE324 —3—
WARNINGS
FOR INDOOR USE ONLY. Keep away from water or damp areas.
WARRANTY INFORMATION
Safety Technology International, Inc. warrants to the original consumer/purchaser that this product shall be free of defects in material and workmanship under normal use and circumstances for a period of one (1) year from the original date of purchase. Electronic warranty form at www.sti-usa.com/wc14.
APPLICATIONS GUIDE Circle = sensor
General Use (Figure 1) – sensors out of range
• For “out of range” sensor(s), position REPEATER between sensor and receiver. • If some sensors are “in range” of the receiver, mount the REPEATER closer to the out of range sensor. The REPEATER should not receive the “in range” sensor packets. • If it is not possible for the REPEATER to receive “out of range” sensors without also picking up “in range” sensor packets: • Move the receiver location forcing “in range” sensors “out of range.” • Purchase an STI 8-Channel Receiver to mirror the “out of range” packets to the original 8-Channel Receiver. • Continue to use the receiver as it is, allowing duplicate sensor packets to be received. This should not change the receiver operation. • Reconfigure system. Single Repeater System - General Use
Multiple Sensor/Re
Keep Repeater out of range from non-repeater sensor
Out of range sensor
Up to 1000 ft.
Up to 1000 ft.
Up to 1000 ft. to farthest sensor 1 - MIRROR MASTER OFF/ON 2 - NORMAL/ENROLL 3 - AUTO RESTORE/LATCH 4 - SIREN TIME/MIRROR# 5 - SIREN TIME/MIRROR# 6 - CHIME OFF/ON 7 - NORMAL/DELETE 8 - MIRROR SLAVE OFF/ON
SW4
SW5
SIREN TIME
MIRROR #
OFF ON OFF ON
OFF OFF ON ON
DISABLED 30 SEC 180 SEC ON CONT
1 2 3 4
In range sensor
Repea
Receiver Repeater
Figure 1 Extended Range System
System with Distance bet
Multiple Sensor/Receiver System (Figure 2)
The REPEATER will receive and transmit any STI protocol signal packets received (except 8-Channel Receiver). Multiple sensors can be arranged to pass packets through the REPEATER to multiple receivers. Up to 1000 ft.
ystem - General Use
Up to 1000 ft.
1 - MIRROR MASTER OFF/ON 2 - NORMAL/ENROLL 3 - AUTO RESTORE/LATCH 4 - SIREN TIME/MIRROR# 5 - SIREN TIME/MIRROR# 6 - CHIME OFF/ON 7 - NORMAL/DELETE 8 - MIRROR SLAVE OFF/ON
SW4
SW5
SIREN TIME
MIRROR #
OFF ON OFF ON
OFF OFF ON ON
DISABLED 30 SEC 180 SEC ON CONT
1 2 3 4
Up to 1000 ft.
Up to 1000 ft. to farthest sensor
1 - MIRROR MASTER OFF/ON 2 - NORMAL/ENROLL 3 - AUTO RESTORE/LATCH 4 - SIREN TIME/MIRROR# 5 - SIREN TIME/MIRROR# 6 - CHIME OFF/ON 7 - NORMAL/DELETE 8 - MIRROR SLAVE OFF/ON
SW4
SW5
SIREN TIME
MIRROR #
OFF ON OFF ON
OFF OFF ON ON
DISABLED 30 SEC 180 SEC ON CONT
1 2 3 4
Receiver Receiver Multiple Sensor/Receiver System(Mirrored) (Master) Repeater
Keep Repeater out of range from non-repeater sensor
Up to 1000 ft.
1 - MIRROR MASTER OFF/ON 2 - NORMAL/ENROLL 3 - AUTO RESTORE/LATCH 4 - SIREN TIME/MIRROR# 5 - SIREN TIME/MIRROR# 6 - CHIME OFF/ON 7 - NORMAL/DELETE 8 - MIRROR SLAVE OFF/ON
SW4
SW5
SIREN TIME
MIRROR #
OFF ON OFF ON
OFF OFF ON ON
DISABLED 30 SEC 180 SEC ON CONT
1 2 3 4
In range sensor
1 - MIRROR MASTER OFF/ON 2 - NORMAL/ENROLL 3 - AUTO RESTORE/LATCH 4 - SIREN TIME/MIRROR# 5 - SIREN TIME/MIRROR# 6 - CHIME OFF/ON 7 - NORMAL/DELETE 8 - MIRROR SLAVE OFF/ON
System Range (Up to 6000 ft. span - with a full mirrored system Receiver #1 Up to Up to 1000 ft. 1000 ft. to farthest sensor SW5
SIREN TIME
MIRROR #
OFF OFF ON ON
DISABLED 30 SEC 180 SEC ON CONT
1 2 3 4
Repeater
Up to 8 sensors
1 - MIRROR MASTER OFF/ON 2 - NORMAL/ENROLL 3 - AUTO RESTORE/LATCH 4 - SIREN TIME/MIRROR# 5 - SIREN TIME/MIRROR# 6 - CHIME OFF/ON 7 - NORMAL/DELETE 8 - MIRROR SLAVE OFF/ON
SW4
SW5
SIREN TIME
MIRROR #
OFF ON OFF ON
OFF OFF ON ON
DISABLED 30 SEC 180 SEC ON CONT
1 2 3 4
Receiver
Keep Repeater out o from each oth
Up to
Repeater
Receiver
ange System
SW4
OFF ON OFF ON
Up to 1000 ft.
– Sensor 8 sensors
1 - MIRROR MASTER OFF/ON 2 - NORMAL/ENROLL 3 - AUTO RESTORE/LATCH 4 - SIREN TIME/MIRROR# 5 - SIREN TIME/MIRROR# 6 - CHIME OFF/ON 7 - NORMAL/DELETE 8 - MIRROR SLAVE OFF/ON
SW4
SW5
SIREN TIME
MIRROR #
OFF ON OFF ON
OFF OFF ON ON
DISABLED 30 SEC 180 SEC ON CONT
1 2 3 4
Receiver #2
with Multiple Locations Monitored Centrally Figure System 2 System with Distance 2 Locations — 4between — Up to 1000 ft. to
Keep out of range Up to 1000 ft. to
Receiver Repeater
Extended Range System (Figure 3)
The REPEATER may be used to extend the range of sensors to a multiple STI 8-Channel Receiver mirroring system. Extended Range System
Up to 1000 ft.
Up to 1000 ft.
Up to 1000 ft.
1 - MIRROR MASTER OFF/ON 2 - NORMAL/ENROLL 3 - AUTO RESTORE/LATCH 4 - SIREN TIME/MIRROR# 5 - SIREN TIME/MIRROR# 6 - CHIME OFF/ON 7 - NORMAL/DELETE 8 - MIRROR SLAVE OFF/ON
SW4
SW5
SIREN TIME
MIRROR #
OFF ON OFF ON
OFF OFF ON ON
DISABLED 30 SEC 180 SEC ON CONT
1 2 3 4
System with Distance
Up to 1000 ft. to farthest sensor
1 - MIRROR MASTER OFF/ON 2 - NORMAL/ENROLL 3 - AUTO RESTORE/LATCH 4 - SIREN TIME/MIRROR# 5 - SIREN TIME/MIRROR# 6 - CHIME OFF/ON 7 - NORMAL/DELETE 8 - MIRROR SLAVE OFF/ON
Receiver (Master)
SW4
SW5
SIREN TIME
MIRROR #
OFF ON OFF ON
OFF OFF ON ON
DISABLED 30 SEC 180 SEC ON CONT
1 2 3 4
Receiver (Mirrored)
Up to 1000 ft.
Repeater
12345678-
Re
Repeater
Single Repeater System - General Use
Multiple Sensor/Receiver System
Keep Repeat from e
System Range (Up to 6000 ft. span - with a full mirrored system
Figure 3
Keep Repeater out of range from non-repeater sensor
Up to 8 sensors
1 - MIRROR MASTER OFF/ON 2 - NORMAL/ENROLL 3 - AUTO RESTORE/LATCH 4 - SIREN TIME/MIRROR# 5 - SIREN TIME/MIRROR# 6 - CHIME OFF/ON 7 - NORMAL/DELETE 8 - MIRROR SLAVE OFF/ON
SW4
SW5
SIREN TIME
MIRROR #
OFF ON OFF ON
OFF OFF ON ON
DISABLED 30 SEC 180 SEC ON CONT
1 2 3 4
Receiver #1
System - General Use Multiple Sensor/Receiver System Central Monitoring of Multiple Locations (Figures 5) Up4 to and 1000 –ft.Sensor
Up to 1000 ft. to farthest sensor Up to 8 sensors Repeater
A receiver, or group of receivers, Up to may be monitored in a central location between multiple REPEATERS as long as 1000 ft. Up to In range the REPEATERS are out of range from each other. 8 sensors
Up to Keep Repeater1000 out offt.range Out range fromofnon-repeater sensor sensor
1 - MIRROR MASTER OFF/ON 2 - NORMAL/ENROLL 3 - AUTO RESTORE/LATCH 4 - SIREN TIME/MIRROR# 5 - SIREN TIME/MIRROR# 6 - CHIME OFF/ON 7 - NORMAL/DELETE 8 - MIRROR SLAVE OFF/ON
SW4
SW5
SIREN TIME
MIRROR #
OFF ON OFF ON
OFF OFF ON ON
DISABLED 30 SEC 180 SEC ON CONT
1 2 3 4
1 - MIRROR MASTER OFF/ON 2 - NORMAL/ENROLL 3 - AUTO RESTORE/LATCH 4 - SIREN TIME/MIRROR# 5 - SIREN TIME/MIRROR# 6 - CHIME OFF/ON 7 - NORMAL/DELETE 8 - MIRROR SLAVE OFF/ON
sensor
Receiver
SW4
SW5
SIREN TIME
MIRROR #
OFF ON OFF ON
OFF OFF ON ON
DISABLED 30 SEC 180 SEC ON CONT
1 2 3 4
1 - MIRROR MASTER OFF/ON 2 - NORMAL/ENROLL 3 - AUTO RESTORE/LATCH 4 - SIREN TIME/MIRROR# 5 - SIREN TIME/MIRROR# 6 - CHIME OFF/ON 7 - NORMAL/DELETE 8 - MIRROR SLAVE OFF/ON
Receiver #1
SW4
SW5
SIREN TIME
MIRROR #
OFF ON OFF ON
OFF OFF ON ON
DISABLED 30 SEC 180 SEC ON CONT
1 2 3 4
System with Multiple Locations Monitored Receiver #2 Centrally UpSTI to protocol packets received (except Repeater – Because REPEATERS Up towill 1000retransmit ft. • REPEATER Feedback any 1000 ft. to farthest sensor Up to 8-Channel Receiver), if two REPEATERS are within reception range of each other they will send packets back 1000 ft. Up toKeep out of range In range and forth to each other. When using more than one REPEATER, keep them out 8ofsensors range from each other. An Up to Repeater sensor Up to 1000 ft. to 1000 ft. to Receiver STI 8-Channel Receiver can be substituted for a REPEATER to farthest eliminate sensor this problem. farthest sensor Up to Up to Receiver #2 Extended Range– System System with Distance between 2 ft. Locations ft. the same 1000 • Dual REPEATER Reception If more than one REPEATER receives a signal packet1000 from sensor, both Repeater Repeater REPEATERS will retransmit the packet. This should not be an issue, but the programmed receiver will then Keep out of range Keep out of range respond to both transmissions. 1 - MIRROR MASTER OFF/ON 2 - NORMAL/ENROLL 3 - AUTO RESTORE/LATCH 4 - SIREN TIME/MIRROR# 5 - SIREN TIME/MIRROR# 6 - CHIME OFF/ON 7 - NORMAL/DELETE 8 - MIRROR SLAVE OFF/ON
r
SW4
SW5
SIREN TIME
MIRROR #
OFF ON OFF ON
OFF OFF ON ON
DISABLED 30 SEC 180 SEC ON CONT
1 2 3 4
1 - MIRROR MASTER OFF/ON 2 - NORMAL/ENROLL 3 - AUTO RESTORE/LATCH 4 - SIREN TIME/MIRROR# 5 - SIREN TIME/MIRROR# 6 - CHIME OFF/ON 7 - NORMAL/DELETE 8 - MIRROR SLAVE OFF/ON
Up to 1000 ft.
1000 ft.
SW4
SW5
SIREN TIME
MIRROR #
OFF ON OFF ON
OFF OFF ON ON
DISABLED 30 SEC 180 SEC ON CONT
1 2 3 4
1 - MIRROR MASTER OFF/ON 2 - NORMAL/ENROLL 3 - AUTO RESTORE/LATCH 4 - SIREN TIME/MIRROR# 5 - SIREN TIME/MIRROR# 6 - CHIME OFF/ON 7 - NORMAL/DELETE 8 - MIRROR SLAVE OFF/ON
1000 ft.
SW5
SIREN TIME
MIRROR #
OFF OFF ON ON
DISABLED 30 SEC 180 SEC ON CONT
1 2 3 4
Receiver (Mirrored)
Up to 1000 ft. to Up to farthest sensor System Range 1000 ft. (Up to 6000 ft. span - with a full mirrored system
SW5
SIREN TIME
MIRROR #
OFF OFF ON ON
DISABLED 30 SEC 180 SEC ON CONT
1 2 3 4
1 2 3 4
Repeater
Up to 1000 ft.
1 - MIRROR MASTER OFF/ON 2 - NORMAL/ENROLL 3 - AUTO RESTORE/LATCH 4 - SIREN TIME/MIRROR# 5 - SIREN TIME/MIRROR# 6 - CHIME OFF/ON 7 - NORMAL/DELETE 8 - MIRROR SLAVE OFF/ON
SW4
MIRROR #
DISABLED 30 SEC 180 SEC ON CONT
sent to the receiver 2 times.
SW4 OFF ON OFF ON
Receiver (Master)
SW4
SW5
SIREN TIME
MIRROR #
OFF ON OFF ON
OFF OFF ON ON
DISABLED 30 SEC 180 SEC ON CONT
1 2 3 4
Receiver (Mirrored)
1 - MIRROR MASTER OFF/ON 2 - NORMAL/ENROLL 3 - AUTO RESTORE/LATCH 4 - SIREN TIME/MIRROR# 5 - SIREN TIME/MIRROR# 6 - CHIME OFF/ON 7 - NORMAL/DELETE 8 - MIRROR SLAVE OFF/ON
SW4
SW5
SIREN TIME
MIRROR #
OFF ON OFF ON
OFF OFF ON ON
DISABLED 30 SEC 180 SEC ON CONT
1 2 3 4
SW5
SIREN TIME
MIRROR #
SW4
SW5
SIREN TIME
MIRROR #
OFF OFF ON ON
DISABLED 30 SEC 180 SEC ON CONT
1 2 3 4
OFF ON OFF ON
OFF OFF ON ON
DISABLED 30 SEC 180 SEC ON CONT
1 2 3 4
SW4
SW5
SIREN TIME
MIRROR #
OFF ON OFF ON
OFF OFF ON ON
DISABLED 30 SEC 180 SEC ON CONT
1 2 3 4
Receiver
Repeater
Keep Repeater out of range
– Sensor from each other
tem Range - with a full mirrored system
Figure 4 – Sensor
System with Multiple Locations Monitored Centrally Keep out of range Up to 1000 ft. to farthest sensor
Up to System with Multiple Locations Monitored Centrally
Up to 1000 ft.
1000 ft.
Up to 1000 ft. to farthest sensor Repeater
Repeater Keep out of range Keep out of range If 2 repeaters receive a Up to signal from the Upsame to 1000 ft. sensor, the signal 1000will ft. be sent to the receiver 2 times.
Repeater
Keep out of range If 2 repeaters receive a signal from the same sensor, the signal will be sent to the receiver 2 times.
Up to 1000 ft. to farthest sensor
SW4
SW5
SIREN TIME
MIRROR #
OFF ON OFF ON
OFF OFF ON ON
DISABLED 30 SEC 180 SEC ON CONT
1 2 3 4
Receiver
Keep out of range
SW4
SW5
SIREN TIME
MIRROR #
OFF ON OFF ON
OFF OFF ON ON
DISABLED 30 SEC 180 SEC ON CONT
1 2 3 4
1 - MIRROR MASTER OFF/ON 2 - NORMAL/ENROLL 3 - AUTO RESTORE/LATCH 4 - SIREN TIME/MIRROR# 5 - SIREN TIME/MIRROR# 6 - CHIME OFF/ON 7 - NORMAL/DELETE 8 - MIRROR SLAVE OFF/ON
SW4
SW5
SIREN TIME
MIRROR #
OFF ON OFF ON
OFF OFF ON ON
DISABLED 30 SEC 180 SEC ON CONT
1 2 3 4
Receiver
Keep out of range 1 - MIRROR MASTER OFF/ON 2 - NORMAL/ENROLL 3 - AUTO RESTORE/LATCH 4 - SIREN TIME/MIRROR# 5 - SIREN TIME/MIRROR# 6 - CHIME OFF/ON 7 - NORMAL/DELETE 8 - MIRROR SLAVE OFF/ON
Up to 1000 ft. to farthest sensor
Up to 1000 ft.
1 - MIRROR MASTER OFF/ON 2 - NORMAL/ENROLL 3 - AUTO RESTORE/LATCH 4 - SIREN TIME/MIRROR# 5 - SIREN TIME/MIRROR# 6 - CHIME OFF/ON 7 - NORMAL/DELETE 8 - MIRROR SLAVE OFF/ON
SW4
SW5
SIREN TIME
MIRROR #
OFF ON OFF ON
OFF OFF ON ON
DISABLED 30 SEC 180 SEC ON CONT
1 2 3 4
Receiver
Up to 1000 ft. Repeater
1 - MIRROR MASTER OFF/ON 2 - NORMAL/ENROLL 3 - AUTO RESTORE/LATCH 4 - SIREN TIME/MIRROR# 5 - SIREN TIME/MIRROR# 6 - CHIME OFF/ON 7 - NORMAL/DELETE 8 - MIRROR SLAVE OFF/ON
Up to 1000 ft. to farthest sensor Repeater
1 - MIRROR MASTER OFF/ON 2 - NORMAL/ENROLL 3 - AUTO RESTORE/LATCH 4 - SIREN TIME/MIRROR# 5 - SIREN TIME/MIRROR# 6 - CHIME OFF/ON 7 - NORMAL/DELETE 8 - MIRROR SLAVE OFF/ON
Up to 1000 ft. to farthest sensor
SW4
SW5
SIREN TIME
MIRROR #
OFF ON OFF ON
OFF OFF ON ON
DISABLED 30 SEC 180 SEC ON CONT
1 2 3 4
Receiver
Up to 1000 ft.
Keep out of range
Up to 1000 ft.
Keep out of range
Repeater
Figure 5
Up to 1000 ft. to farthest sensor Repeater
1 - MIRROR MASTER OFF/ON 2 - NORMAL/ENROLL 3 - AUTO RESTORE/LATCH 4 - SIREN TIME/MIRROR# 5 - SIREN TIME/MIRROR# 6 - CHIME OFF/ON 7 - NORMAL/DELETE 8 - MIRROR SLAVE OFF/ON
Up to 1000 ft. Receiver Receiver SW4
OFF ON OFF ON
Repeater
Receiver
Repeater
1 - MIRROR MASTER OFF/ON 2 - NORMAL/ENROLL 3 - AUTO RESTORE/LATCH 4 - SIREN TIME/MIRROR# 5 - SIREN TIME/MIRROR# 6 - CHIME OFF/ON 7 - NORMAL/DELETE 8 - MIRROR SLAVE OFF/ON
1 - MIRROR MASTER OFF/ON 2 - NORMAL/ENROLL 3 - AUTO RESTORE/LATCH 4 - SIREN TIME/MIRROR# 5 - SIREN TIME/MIRROR# 6 - CHIME OFF/ON 7 - NORMAL/DELETE 8 - MIRROR SLAVE OFF/ON
—5 —
Up to 1000 ft. to farthest sensor Repeater
Up to 1000 ft. to farthest sensor
Repeater
Up to Up to Up to 1000 ft. to Up to 1000 ft. sensor Up farthest to 1000 Keep ft. to Repeater out of range1000 ft. 1000 ft. farthest sensor from each other Keep out of range
Repeater
OFF ON OFF ON
SIREN TIME
OFF OFF ON ON
signal from theft. Up to 1000 toLocations System 2same sensor, the signal will be Up to with Distance between 1000 ft. farthest sensor
1 - MIRROR MASTER OFF/ON 2 - NORMAL/ENROLL 3 - AUTO RESTORE/LATCH 4 - SIREN TIME/MIRROR# 5 - SIREN TIME/MIRROR# 6 - CHIME OFF/ON 7 - NORMAL/DELETE 8 - MIRROR SLAVE OFF/ON
Receiver (Master)
1 - MIRROR MASTER OFF/ON 2 - NORMAL/ENROLL 3 - AUTO RESTORE/LATCH 4 - SIREN TIME/MIRROR# 5 - SIREN TIME/MIRROR# 6 - CHIME OFF/ON 7 - NORMAL/DELETE 8 - MIRROR SLAVE OFF/ON
SW5
If 2 repeaters a Upreceive to
Range System Up to
p to 0 ft.
SW4
OFF ON OFF ON
Up to 1000 ft. to farthest senso Repeater
ADDITIONAL WIRELESS ALERT SERIES PRODUCTS STI-34098 STI-34104 STI-V34104 STI-34108 STI-34188 STI-34101 STI-34151 STI-34201 STI-34301 STI-34401 STI-34501 STI-34601 STI-34701 STI-34752
Single Channel Slave Receiver 4-Channel Receiver 4-Channel Voice Receiver 8-Channel Receiver 8-Zone Relay Board Solar Powered Driveway Monitor Sensor Battery Powered Driveway Monitor Sensor Wireless Mailbox Alert Sensor Wireless Garage Sentry Sensor Wireless Universal Alert Sensor Wireless Door Entry Alert® Sensor Wireless Doorbell Button Indoor Wireless PIR Outdoor Wireless PIR
STI-6200WIR Wireless Fire Extinguisher Theft Stopper STI-6200WIR4 Wireless Fire Extinguisher Theft Stopper w/Receiver STI-6400WIR Wireless Exit Stopper Door Alarm STI-6400WIR4 Wireless Exit Stopper Door Alarm with Receiver STI-6517A Wireless Stopper Station Shield with Sound STI-6517B Wireless Stopper Station Shield with Sound and Transmitter STI-6517C Stopper Station Shield with Wireless Transmitter STI-6517D Wireless Stopper Station Shield with Button Sound and Transmitter STI-30104 Lamp Controller STI-30105 Extended Antenna STI-34105 Voltamax 12VDC (500mA) Power Supply STI-34106 Keyfob STI-34109 Repeater
2306 Airport Rd • Waterford, MI 48327, USA Phone: 248-673-9898 • Fax: 248-673-1246
[email protected] • www.sti-usa.com
Safety Technology International (Europe) Ltd. Unit 49G Pipers Road • Park Farm Industrial Estate • Redditch Worcestershire • B98 0HU • England Tel: 44 (0) 1527 520 999 • Fax: 44 (0) 1527 501 999 E-mail:
[email protected] • Web: www.sti-europe.com
We protect the things that protect you.®
Inst. Sht. STI-34109 DEC2012
