Transcript
Option MF2 Series Mounting Frame Bi-Level Non-Refrigerated Fountain Stainless Steel Model: q A0000000-MF2
S U G G E S T E D
Model A0000000-MF2 is an in-the-wall mounting frame for bi-level, non-refrigerated fountains. The mounting frame provides additional support and is manufactured from a heavy gage galvanized steel and supplied with pre-drilled mounting holes.
Model A171408F-BFS2 Shown
n Heavy
gage galvanized steel mounting holes
“NO OPTIONS AVAILABLE”
Member of U.S. Green Building Council
Acorn Engineering assumes no responsibility for use of void or suspended data. © Copyright Acorn Engineering, City of Industry, CA Member of Morris Group International. Please visit www.acorndrinkingfountains.com for most current specifications.
Submittal # A0.MF2 Date: 03/26/2012
Recyclable Product
COMPLIES WITH
S T A N D A R D
n Pre-drilled
Water Conserving Product
ACORN ENGINEERING
Member of
15125 Proctor Ave. City of Industry, CA 91746 U.S.A. Phone 800-591-9360 626-336-4561 Fax 626-855-4894
T E C H N I C A L
All dimensions are nominal and subject to manufacturer's change without notice. Acorn Engineering assumes no responsibility for use of void or suspended data. © Acorn Engineering, City of Industry, CA, Member of Morris Group International. Please visit www.acorndrinkingfountains.com for most current specifications.
q Stainless Steel Model:
A0000000-MF2
2021" [508] CENTERLINE NOTCHES
1" 392 [1003] 4" [102] MIN. DEPTH
TYPICAL MTG. HOLES SEE NOTE 7
19" [483] 19" [483]
SPACING TO BE PLACED BETWEEN FRAMES
1" 198 [486]
BI-LEVEL MOUNTING FRAME SHOWN STANDARD CONFIGURATION SHOWN HIGHER UNIT ON THE LEFT
*25" [635] FINISHED FLOOR
WALL OPENING
MOUNTING FRAME SHOWN FOR ACORN-AQUA FOUNTAINS WITH -RBL (REVERSE BI-LEVEL) CONFIGURATION
GENERAL NOTES: 1. ALL DIMENSIONS ARE IN INCHES [MM]. 2. MOUNTING FRAME FOR USE WITH BI-LEVEL FOUNTAINS. *3. VERTICAL FRAME HEIGHT IS SHOWN FOR RECOMMENDED ADULT HEIGHT, WITH 27” [686] KNEE CLEARANCE ON THE LOWER FOUNTAIN AND A 40” [1016] BASIN HEIGHT ON THE UPPER FOUNTAIN. ADJUST DIMENSIONS AS NECESSARY TO COMPLY WITH FEDERAL, STATE, & LOCAL CODES. REFER TO FOUNTAIN ROUGH-IN FOR MORE DETAILS ON FIXTURES. 4. HOLD ROUGH-IN DIMENSIONS ± 18” [3]. 5. THIS FRAME IS USED WITH SEVERAL FOUNTAIN MODELS. WASTE & SUPPLY HEIGHTS ARE DETAILED IN THE FOUNTAIN ROUGH-IN DRAWING. 6. FRAME MUST BE INSTALLED SO THE SIDE LIP OF FRAME OVERLAPS & BUTTS UP AGAINST FINISHED WALL. 5 7. SECURE FOUNTAIN FRAMES TO WALL AND SPACER USING 1 4” LAG SCREW IN Ø 16” [8] MOUNTING HOLES, 16 PLACES.
A0.MF2
Date: 03/26/2012
Five Year Limited Warranty- (Continental United States and Canada Only) The following components are warranted for five years: Compressor, Condenser Coil and Refrigeration Coil. The following components shall only be warranted for a period of one year: Evaporator Can Assembly, Thermostat, Fan Motor, Cartridge, Push Buttons, Compressor Starting Relay/Overload/Capacitor and Activation Linkage. Other parts are warranted for one (1) year from date of installation. Limited Export Warranty- One (1) year on parts only.
800-591-9360 626-336-4561
