Preview only show first 10 pages with watermark. For full document please download

Subzero-10 1500 Watts

   EMBED


Share

Transcript

SUBZERO-10 1500 WATTS 1” = 2.54 cm 1 cubic foot = 1728 cubic inches Grille Clearance: 2” Displacement: Winner of the 2004 Design & Engineering Award INNOVATIONS INTERNATIONAL CES #1 Sealed design for tight bass #2 Port tuned design for deep bass #3 Ported design 16" 12" 11" 11” 15" 15 1/2" #2 11" 12" #1 4" diameter 12" SUBZERO-10" Outer dimension shown using 3/4" thick MDF Total outer box volume = 0.91 cubic foot. Sealed design for tight bass SUBZERO-10" 12" Port Outer dimension shown using 3/4" thick MDF. Total outer box volume = 1.22 cubic feet. SUBZERO-10" PORT (2"x10.5"x11") Internal dimensions 8 1/2" long Outer dimension shown using 3/4" thick MDF Total outer box volume = 1.61 cubic feet. SUBZERO-10 Cut out hole 235mm / 9 1/4” 23 1/2” 15” 12” SUBZERO-10" Mounting depth 220mm 6 1/2” SUBZERO-10" 18 1/2” Outer dimension shown using 3/4" thick MDF Total outer box volume = 2.73 / 1.36 per sub Specifications are subject to change without notice HANDCRAFTED IN USA. HOW TO WIRE / FUSE YOUR SUBZERO TO AN AMPLIFIER 2-channel 2 x 4-ohm load (voice coils separated) (no fuses) VC #2 VC #2 VC #1 VC #2 VC #1 VC #1 P P P S 1+ 2+ DO NOT USE MONO 2-OHMS 1 - CH-1 2 - 1+ 2+ CH-2 TYPICAL AMPLIFIER TERMINAL TYPICAL AMPLIFIER TERMINAL The diagram -on the left side- shows the PSP terminal in a 2-ohm parallel configuration (both voice coils are connected in parallel). Simply place the 2 fuses in the outer positions in the fuse placement area. Insert the negative speaker wire to the far left insert and one positive to the far right insert. This diagram shows the PSP terminal in a 4-ohm configuration (the two voice coils are separated). No fuses are used in this configuration,the voice coils are powered up separately. 1 - 8-GAUGE - P S 8-GAUGE 2 8-GAUGE 8-GAUGE - 8-GAUGE 1 P S 3mm Hex-nut cable fasteners 8-GAUGE P 1-channel 8-ohm load (voice coils in series) (1 fuse) 2 - 1+ 2+ DO NOT USE 8-GAUGE 2-channel 2-ohm load (voice coils in parallel) (using 2 fuses) 8-GAUGE The Subzero subwoofer comes equipped with 2 voice coils (dual 2x4 ohms), it can be used in 2, 4 and 8ohm configurations. The terminal comes equipped with fused jumpers, the voice coil can be easily configured in series or in parallel to match the amplifier in use. It is just a simple flip of a fuse, here’s how it works. PSP (Parallel Series Parallel) Terminal MONO 8-OHMS TYPICAL AMPLIFIER TERMINAL The diagram - on the right side-displays the PSP in an 8-ohm mode. You will notice that there is only one fuse in the center of the fuse placement area. The voice coils are wired in series. Insert the negative speaker wire to the far left insert and one positive to the far right insert. Electro Mechanical Parameters Name = Subzero 10 (broken in) Xmax = 31.7500E-3 M Note = VI MEASUREMENTS Krm = 52.9380E-3 Ohm Model = TSL Erm = 667.0000E-3 Domain = FreeAir Kxm = 78.4200E-3 H Shape = Round Exm = 685.0000E-3 Profile = Cone Rms =19.3984 N·S/M Fmd = 3.0000 KA Mms = 155.7620 g Qmd = 1.0000 Cms =197.1628 uM/N Flp = 8.0000 KA Vas = 1.0830 Ft³ Qlp = 2.0000 Fo = 28.7195 Hz Znom = 8.0000 Ohm Qms = 1.4489 Revc = 7.7000 Ohm Qes = 0.6994 Sd = 33.0000 msqM Qts = 0.4717 Mmd = 152.3169 g BL = 17.5913 T·M Pmax = 1.0000E3 W Levc = 4.9888 mH Rtvc = 250.0000E-3 °C/W SPLo = 82 dB Xgap = 500.0000E-3 In No = 0.0995821% Xcoil = 3.0000 In