Summary Of Airclient 241 Features And Benefits

Transcript

The airClient 241 (sB3417) is a Customer Premise Equipment (CPE), designed specifically for carriers and communication service providers to establish end-to-end high performance, license exempt wireless infrastructure capable of delivering data and voice applications. This revolutionary CPE can be self-installed by the subscribers to eliminate the truck-roll, thus making it suitable for highly scalable and large network deployments. The advanced COFDM radio design extends the wireless service coverage in Near Line of Sight (NrLOS) conditions. The airClient 241 is available in many software configurations and two form factors to suit individual project requirements. Quality of Service (QoS) for traffic prioritization and bandwidth management for the wireless interface make the airClient 241 the intelligent choice for neighborhood-wide ISP networks. The special hardware and software features significantly simplify how a subscriber can self-install the CPE and connect to the service provider’s network. When used with smartBridges suite of remote management solutions, service providers can realize significant cost savings on new subscriber provisions. Maintenance and after-sales support costs are also reduced. Summary of airClient 241 Features and Benefits Features Benefits COFDM Radio Best-in-class radio performance with COFDM technology ensure high throughput, spectral efficiency, resistance to multi-path delays and Near Line of Sight performance Advanced Radio Performance High transmit radio power and ultra high receive sensitivity for LongRange™ coverage Self-Install CPE with an Integrated Antenna Lower overall cost and fast installation External Antenna Support Connector allows use of higher gain external antenna for longer range Advance QoS Function Traffic prioritization queues for data and voice applications Bandwidth Control at CPE Controls upstream/downstream bandwidth according to the Service Level Agreement (SLA) Comprehensive Network Features Built-in NAT and Routing function to isolate service provider’s network from customer’s network Unified Web and SNMP Compliant Remote Management Interface Permits remote control, configuration, maintenance and firmware upgrade of the CPE Auto-Configuration System (ACS) and Device Management System (DMS) Service Providers can remotely provision and manage the CPE Intelligent Networking Features for Data and Voice Services Quality of Service (QoS) for traffic prioritization, bandwidth management for the wireless interface makes airClient 241 the intelligent choice for enterprise class customers. The ability to guarantee bandwidth to critical applications, limit bandwidth to low priority applications, and mark packets to provide end-to-end QoS, ensures enhanced performance for data and voice traffic. The airClient 241 includes Network Address Translation (NAT) and Router capabilities for isolating the service provider's network. When used with airPoint™ Nexus, the airClient 241 can support unlimited MACs as a fully transparent bridge for joining remote network segments. Subscriber Provisioning and Management System Field installation is time consuming and expensive; therefore, the airClient 241 is designed for rapid out-of-thebox installation. Service providers can now better manage and support the airClient 241 installed at the customer premise through the optional Auto-Configuration System (ACS) and Device Management System (DMS). Every time the CPE associates to the service provider’s network, the ACS automatically authenticates and configures the CPE with the correct bandwidth settings, device parameters, and firmware version. The DMS can be used by the service provider for post sales support, including getting remote access to the CPE for device troubleshooting and configuration. LongRange™ Performance that goes the Distance airClient 241 features LongRange™ wireless design to deliver high data throughput and long operating range. smartBridges' superior design of the radio receiver enhances the sensitivity to an incredible -97 dBm level. The superior receiver and transmitter characteristics and parameter optimization for long range result in the wireless coverage. Better range translates directly into lower wireless infrastructure cost when covering a large area. Power over Ethernet (PoE) Support The airClient 241 is powered through the Ethernet cable by using the PoE injector that is supplied as a standard accessory. PoE support allows the airClient 241 to be installed away from the subscriber’s computer, and at a location which offers better signal strength from the Access Point. Antenna Options The airClient 241 comes standard with an integrated antenna, sufficient for most subscriber locations. For longer distances or for higher data speeds, an optional higher gain antenna can be attached to the CPE at the external antenna connector. GENERAL SPECIFICATIONS Model No sB3417-XX-XX (please refer to the Order Matrix below) Availability Now Form Factor Residential (-R1) Enterprise (-T1 and -T2) RADIO PARAMETERS Radio Frequency Bands License Exempt ISM: 2.400 - 2.485 GHz* Wireless Modulation Coded Orthogonal Frequency Divisional Multiplexing (COFDM) - BPSK, QPSK, 16QAM, 64QAM Direct Sequence Spread Spectrum (DSSS) - DBPSK, DQPSK, CCK Self-adapting modulation to maintain optimal link performance under different environmental conditions Data Rates 54, 48, 36, 24, 18, 12, 9, 6, 11, 5.5, 2 and 1 Mbps (With Auto-Fall back) RF Channels 14 channels (20 MHz channel width at 5 MHz spacing) Typical Receive Sensitivity at Integrated Antenna (dBm) -102 @ 1 Mbps, -78 @ 54 Mbps (10% PER) with integrated antenna Typical Receive Sensitivity at External Connector (dBm) -110 @ 1 Mbps, -86 @ 54 Mbps (10% PER) with integrated antenna -95 @ 1 Mbps, -71 @ 54 Mbps (10% PER) Self-adapting, depending on the radio modulation Wireless Error Correction FEC, ARQ Standards Compliance IEEE 802.11b/g High Availability System Self-monitoring and auto-recovery Watch Guard with Hardened Linux OS Antenna Alignment Tools LED display, RSSI (Radio Signal Strength Indicator) graph PHYSICAL, ENVIRONMENTAL AND COMPLIANCE PARAMETERS Network Connection One RJ45 connector (IEEE 802.3 compliant 10/100 BaseT with Auto MDI/MDX) Integrated Antenna External Antenna Connection Power over Ethernet (PoEI & Adaptor included) 7 dBi Gain with Beam width 65º/65º (V/H) 15 dBi Gain with Narrow Beam width 27 º/30º (V/H) One RP-SMA (Male) Connector (50 Ohm)+ One N (Female) Bulkhead Connector (50 Ohm)+ Input: 100V to 250V AC, 47-63 Hz; Output: 9V DC, 10 Watts (Maximum Ethernet cable length: 25m) Input: 100V to 250V AC, 47-63 Hz; Output: 18V DC, 10 Watts (Maximum Ethernet cable length: 100m) 5 Watts 5 Watts at environmental temperature above -4ºF ( -20ºC). TBD Watts at temperature below -4ºF (-20ºC). Power Consumption LED Indicators LEDs for viewing of RF Signal strength, RF and Ethernet activity Operating Environment T1 models only 14ºF to 140ºF (-10ºC to +60ºC), 5% to 95% non-condensing humidity 14ºF to 140ºF (-10ºC to +60ºC), 5% to 95% non-condensing humidity; indoor rated T2 models only -49 ºF to 140ºF (-45ºC to +60ºC), 5% to 95% non-condensing humidity Enclosure Mounting Accessory Dimensions and Weight Indoor rated plastic Outdoor IP65 rated plastic Optional mounting kit for installation on wall or window Included swivel mounting kit for easy installation on wall or window and quick antenna alignment Unit (without mounting accessory): 4.72” x 1.65” x 5.11” (120 x 42 x 130 mm), approx. 0.44 lb (0.2 kg) Unit (without mounting accessory): 11.1" x 11.2" x 2.4" (280 x 285 x 60 mm), approx. 4.45 lb (2.1 kg) Shipping: 12" x 12" x 6" (305 x 305 x 152 mm), approx. 7.28 lb (3.3 kg) Certifications USA: FCC 47 CFR Part 15C, Section 15.247, 15.407 Europe: ETSI 300 328, EN301 489-1.EN301 489-17, CE! Marked, WEEE compliance Canada: RSS 139 Order Matrix When placing an order, please quote the full model number comprising of the form factor (-R1, -T1 or -T2) and the firmware type (-01 or -02). Form Factor Residential (-R1) Enterprise (-T1) Enterprise (-T2) -01 sB3417-R1-01 sB3417-T1-01 sB3417-T2-01 -02 sB3417-R1-02 sB3417-T1-02 sB3417-T2-02 Firmware Type FEATURE SPECIFICATIONS Firmware Type -01 -02 RADIO PARAMETERS Transmit Power EIRP @ 6 Mbps OFDM with Integrated Antenna (Adjustable) - Residential R1 models - Enterprise T1 and T2 models Transmit Output Power @ 6 Mbps OFDM at Antenna Connector (dBm) (Adjustable) +20dBm (100mW) to +7dBm (5mW) +25dBm (316mW) to +7dBm (5mW) +28dBm (631mW) to +15dBm (32mW) +33dBm (1995mW) to +15dBm (32mW) NA +18dBm (63mW) to 0dBm (1mW) OPERATIONAL PARAMETERS With Integrated Antenna @ CPE and 15dBi External Sector Antenna at the smartBridges Access Point (sB3215) in compliance with EIRP limits in FCC Domain Recommended Link Distance - Residential R1 models 2 km 4 km - Enterprise T1 and T2 models 4 km 8 km Typical Useful Wireless Throughput # Up to 1024 kbps aggregate TCP and UDP traffic for Up/Down Bandwidth Management Bandwidth control for upstream and downstream rates on the wireless interface in 1kbps increment Data Throughput Turbo Booster Up to 2048 kbps aggregate TCP and UDP traffic for Up/Down NA Fast Frames for high spectral efficiency NAT mode Rip v2 Router NA Traffic Prioritization with IEEE 802.11e for data and voice applications Data Security WEP 64/128 TKIP/RC4 VLAN Support VLAN Pass through Network Topology NETWORK MANAGEMENT AND SECURITY Traffic Prioritization Network Support DHCP Server and Client Network Redundancy NA List of alternate Access Points for auto-failover Operating Profile NA Multiple operating profiles Web browser based intuitive GUI control from the wired interface. Devices monitoring from wireless interface Remote Web, CLI and SNMP based management on wired and wireless interface, Administrator and User level access Remote firmware upgrade Remote firmware upgrade, Remote Link Test, Integrated Link Budget, Radio and Ethernet traffic statistics, Configurable Remote Syslog reporting and SNMP traps NA Full device monitoring and management with InterMapper. Easy integration with 3rd party NMS. Application note and scripts available for MRTG. simpleDeploy device configuration Auto-Configuration System (ACS), Device Management System (DMS) Management Interface Diagnostic and Performance Management Tools Network Management System (NMS) Other Management System * All channels may not be available in your regulatory domain # Expected performance, subject to RSSI and link conditions + Enabled in 02 and 03 firmware versions For detailed product information, visit www.smartbridges.com/products/aC241.asp To contact us, visit www.smartbridges.com/contact/ North America ♦ South America ♦ Europe ♦ Russia ♦ Middle East ♦ Africa ♦ South Asia ♦ Asia Pacific Copyright © 1999-2008 smartBridges. All rights reserved. (Version 1.3) The content herein is subject to change without further notice. smartBridges, airHaul, Nexus, airPoint, airClient and/or all other products and/or services referenced herein are either registered trademarks, trademarks or service marks of smartBridges Pte Ltd. All other names are/or may be the trademarks of their respective owners.