Transcript
SUPPLEMENTAL TIMER INSTRUCTIONS for Models HRO100, HRO300 and HRO500 If the timer on your model HRO100, HRO300 or HRO500 rotary oven operates differently than discussed in the original Instructions, F-17609 Rev. A (6-90), or the Supplemental Timer Instructions, F-18270 (10-91), use the following in addition to the original instructions where applicable. CONTROLS (Fig. 1) Thermostat
- Temperature range 150°F to 450 °F. Controls the oven temperature.
Rotating Switch - Controls power to the rotisserie motor. Switch has three positions: Turns the rotisserie motor off. When enabled, the rotisserie motor is controlled by the timer. Turns the rotisserie motor on. Power Switch
- Controls power to the rotisserie oven. Switch has three positions: Turns power to the rotisserie oven off and cancels any programs. When enabled, oven heaters and lamps are controlled by the timer and the thermostat. Turns power to the thermostat, heating elements and lamps on.
Digital Timer
- When enabled, controls timed oven operations of the rotisserie motor, oven heaters and lamps. Timer Sets an intermediate timer stop for checking, basting, etc. When the beeper to silence. sounds, press To start cooking, press TIMER, then press knob to set the cooking duration. the
. Display shows 0:00. Rotate
Displays the time of day when cooking stops. To set a delayed start, set the cooking duration as described above. Then, press STOP. After the end time knob to advance the time of day when cooking stops. displays, rotate the Rotate clockwise to increase the time and counterclockwise to decrease the time. Display
- Normally displays the time of day. During a cooking cycle, pressing COOK displays the remaining time. Pressing STOP displays the time when the cooking cycle will end. After a few seconds, the display returns to the time of day.
To Set the Time of Day After the oven has been disconnected for a period of time, you must set the time of day before programming any automatic (timed) cooking function. 1. Reconnect the oven and turn the POWER switch to AUTO. TIMER and at the same time. Release the two buttons and rotate the 2. Press display shows the correct time of day. The oven begins heating.
knob until the
3. Press and rotate the knob past zero then back to zero again. The oven will stop heating within a few seconds. All programming may be done now. NOTE: In the event of a power failure longer than 50 seconds, all programming is lost. When power is restored, controls must be reprogrammed. You cannot reset the time of day when the timer is programmed for an automatic function. FORM 34771 (Apr. 2002)
DIGITAL TIMER
DISPLAY
TIMER KNOB
COOK STOP
THERMOSTAT
ROTATING SWITCH: OFF, AUTO, MANUAL
POWER SWITCH: OFF, AUTO, MANUAL
PL-41675-1
Fig. 1
Manual Mode If the POWER switch is on MANUAL, the thermostat controls heating, and the ROTATING switch controls the rotisserie. The rotisserie is on if the ROTATING switch is on either AUTO or MANUAL; the O position is off. Automatic Mode Rotate the POWER switch and the ROTATING switch to to display 0:00. Within a few seconds, rotate the press (hours:minutes).
. Set the thermostat. Press
to begin.
. To delay the start of the cooking
Example Cooking Program
If a delayed start was programmed, the timer waits and starts the cooking process so it ends when requested.
and then
knob to set the cooking duration time
To display the time when the end of the cooking program will occur, press knob. program, advance the end time by rotating the Press
TIMER
Delayed Start
Time of Day
Cooking Duration
Cooking Stop Time
Delayed Start Time
8:15
1:30
10:00
8:30
To Set an Intermediate Timer Alert TIMER and rotate the knob You can set an intermediate alert any time during the cooking program. Press to set the desired time. Press TIMER at any time during a cooking program to display the amount of time remaining on the intermediate timer.
701 S. RIDGE AVENUE TROY, OHIO 45374-0001
937 332-3000
FORM 34771 (Apr. 2002)
www.hobartcorp.com
Printed in U.S.A.
