Sv- 8100.w - Crimestopper

Transcript

SV- 8100.W Universal Wireless Camera Transmitter INSTALLATION INSTRUCTIONS: The SV-8100.W is a Wireless Transmitter that transmits a video signal from a camera to a monitor without having to run any video cables from the front to the back of the vehicle. This is perfect for the bigger trucks or SUVs that require a large amount of video cable run the length of the vehicle. The SV-8100.W can be hooked up to any SecurView™ or PlateCam™ camera. FEATURES: • • • • • • • • • Universal Wireless Camera Transmitter Converts any standard cable camera and monitor into a wireless system Requires no video cable to be ran from the camera to the monitor Effective Transmitting Range: 50-60Ft. Perfect for longer vehicles such as: Trucks, Trailers, SUVs, Buses or Motor Homes Easy to Install, no major tools required Transmitter and Receiver can be hidden behind Trunk and Dash Panels Works with and camera and monitor that use RCA Inputs and Outputs Cuts down installation time INSTALLATION INSTALLATION PRECAUTIONS: 1. Make sure to connect the SV-8100.W to the correct voltage. Failure to do so may result in damage to the unit or any other components hooked up to it. 2. Do not hide the Transmitter or Receiver next to any thick metal plates or wire looms. This may cause strong interference with the wireless signal. 3. Mount the Transmitter and Receiver in a way so there is minimal vibration. Excessive vibration may cause interference. WIRING: 1. Choose a convenient place to mount the Transmitter and Receiver for the unit. Behind the trunk panels and under the dash board, are usually suitable locations. 2. Connect the Red wire on the Transmitter and Receiver to +12V Reverse Light, and the Black wire of both units to Chassis Ground. 3. Connect the Yellow RCA video cable of the Transmitter to the RCA Video Output of your camera. 4. Connect the Yellow RCA video cable of the Receiver to the RCA Video Input of your monitor. 5. The +12V power plug on the Transmitter and receiver can be used to plug in Power and Ground for your camera and monitor. NOTE: Some cameras and monitors will not have this type of plug for +12V and Ground. In this case you can simply hardwire +12V and Ground for your camera and monitor and disregard this plug. NOTE: Make sure all RCA cables and Power Plugs are secured tightly and wrapped in Electrical Tape to prevent short circuits. Red Black Camera +12V Reverse Light Ground SV-8100.W Receiver Yellow RCA Video Plug +12V Power Plug Yellow RCA Video Plug +12V Power Plug Black SV-8100.W Transmitter Ground Red +12V Reverse Light Monitor SPECIFICATIONS: WIRELESS TRANSMITTER WIRELESS RECEIVER Voltage Input: DC12V Working Temperature: -20°C~+70°C Working Temperature: -20°C~+75°C Working Humidity: 85% RH Transmit Frequency: 2400 ~ 2483MHz Demodulation Method: FM Video Output Impedance: 75Ω, Typ. Frequency Response: 6db band width Output Frequency Ranges: 100Hz ~ 10KHz Transmit Frequency: 7dBm Effective Transmit Distance: 60Ft – 70Ft Voltage Input: DC12V Working Temperature: -20°C~+70°C Working Temperature: -20°C~+75°C Working Humidity: 85% RH Transmit Frequency: 2400 ~ 2483MHz Demodulation Method: FM Video Output Impedance: 75Ω, Typ. Frequency Response: 6db band width Output Frequency Ranges: 100Hz ~ 10KHz High Receiving Flexibility: -87dBm DISCLAIMER: Under no circumstances shall the manufacturer or distributor of the SecurView™ SV-8100.W product be held liable for consequential or incidental damages sustained in connection with the use of the SecurView™ SV-8100.W product. www.crimestopper.com [email protected] Phone (800) 998-6880 FAX (805) 581-9500 © 2009 Crimestopper Security Products