Sv800ukl - Lakeland

Transcript

OWNER’S GUIDE SV800UKL SV800UKL 54_E_IB_111004_1.indd 1 11-10-04 4:05 PM WARNINGS IMPORTANT SAFETY INSTRUCTIONS For Household Use Only WHEN USING YOUR SHARK CORDLESS STICK VACUUM, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED, INCLUDING THE FOLLOWING: ® READ ALL INSTRUCTIONS BEFORE USING YOUR SHARK CORDLESS STICK VACUUM. ® IMPORTANT: This appliance can be used by children aged from 8 years and above and persons with reduced physical or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning the use of the appliance in a safe way and understand the hazards involved. Children should be supervised to ensure that they do not play with the applaince. Cleaning and user maintenance shall not be made by children without supervision. IMPORTANT: Instructions for proper disposal of this product, pursuant to the European Union’s directive on electrical waste. Please do not dispose of any electrical equipment as ordinary waste. Help to conserve natural resources and protect the environment: when you have finished using this product, please dispose of it at your local waste collection or recycling centre in the area reserved for electrical equipment. Contact your local authority to find the nearest waste collection centre. To remind you to dispose of this product responsibly and separately from ordinary waste, it is marked with the symbol of a crossed-out rubbish bin. GENERAL ELECTRICAL SAFETY: WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK OR INJURY DO NOT USE OUTDOORS OR ON WET SURFACES. 1 DO NOT use or charge the unit outdoors. 2 DO NOT use or charge the unit on wet surfaces. Plug adapter directly and only in a standard (220-240V., 50/60Hz) electrical outlet. 9 DO NOT run the vacuum over the charging adapter cord. 10 Keep charging adapter cord away from heated surfaces. 11 DO NOT attempt to use the charging adapter with any other product nor attempt to charge this product with another charging adapter. 12 Only use charging adapter model number HK-AC-160A020-GB provided. 13 Always turn the vacuum off before connecting or disconnecting the motorized floor brush or crevice tool. GENERAL USE: 14 Use only on dry, indoor surfaces. 15 Store the cordless vacuum indoors. Put the cordless vacuum away after use to prevent accidents. 16 Use only as described in this manual. DO NOT use for any purpose other than described in this user’s guide. 17 Use only cleaning attachments supplied with this unit. 18 Keep your work area well lit. 19 Keep the vacuum moving over the carpet surface at all times to avoid damaging the carpet fibers. 20 DO NOT put any objects into openings. 21 DO NOT use with any opening blocked; keep free of dust, lint, hair and anything that may reduce airflow. 22 DO NOT use the vacuum cleaner without dust cup and filter in place. 23 DO NOT vacuum up any liquids. 24 DO NOT pick up anything that is burning or smoking such as cigarettes, matches or hot ashes. 3 DO NOT immerse vacuum cleaner or charging adapter in water or other liquids. 25 DO NOT use to pick up flammable or combustible liquids such as gasoline or use vacuum in areas where their fumes may be present. 4 DO NOT handle vacuum or charging adapter with wet hands. 26 DO NOT pick up toxic solutions such as chlorine bleach, ammonia or drain cleaner. 5 DO NOT use charging adapter if power cord has been damaged. 27 DO NOT use in an enclosed space where vapors are present from paint, paint thinner, moth-proofing substances, flammable dust or other explosive or toxic materials. 6 DO NOT abuse the charging adapter cord. NEVER carry the charging adapter by the cord. 7 DO NOT unplug the charging adapter by pulling on cord; to unplug, grasp the plug, not the cord. 8 DO NOT use charging adapter with an extension cord. 2 28 DO NOT run the vacuum over large-sized objects. 29 DO NOT pick up hard or sharp objects such as glass, nails, screws or coins that could damage the vacuum cleaner. www.lakeland.co.uk SV800UKL 54_E_IB_111004_1.indd 2 11-10-04 4:05 PM CONTENTS 30 DO NOT place vacuum on unstable surfaces such as chairs or tables. 31 DO NOT allow the vacuum to be used as a toy. 32 Close attention is necessary when used by or near children. 33 DO NOT use cordless vacuum cleaner or charging adapter if it has been dropped, damaged, left outdoors or submerged in water. To avoid the risk of electric shock, do not disassemble or attempt to repair the appliance on your own. If the supply cord is damaged, it must be replaced by a qualified electrician in order to avoid a hazard. Incorrect re-assembly or repair can cause a risk of electrical shock or injury to persons when the appliance is used. Assembly 4 Using your Cordless Stick Vacuum 5 Maximizing the Life of your Battery 5 Care and Maintenance 7 Troubleshooting Guide 10 34 Keep hair, face, loose clothing, fingers and all body parts away from openings and moving parts. 35 This product is powered by Ni-Mh batteries, which must be recycled when the replaceable battery or leaking battery or battery pack is at the end of its life. The battery must be removed from the appliance before it is recycled. The appliance must be disconnected from the supply when removing the battery. Do not incinerate batteries or expose to high temperatures, as they may explode. Please ensure you deliver the battery for recycling to the battery collection system in your country. 36  Leaks from battery cells can occur under extreme conditions. If the liquid gets on the skin - wash immediately with soap. If the liquid gets into the eyes, flush them immediately with clean water for a minimum of 10 minutes and seek medical attention. 37 The battery must be removed from the appliance before it is discarded. 38 Batteries are to be recycled or disposed of safely. 39 Use extra care when cleaning on stairs. DUST CUP/FILTER: Thank you for purchasing the Shark® Cordless Stick Vac 40 Before turning on the vacuum: • Make sure that the dust cup and filter are securely in place after routine maintenance. • Make sure that all components and filters are thoroughly dry after routine cleaning. • Only use filters and accessories provided by EUROPRO Operating LLC. [Failure to do so will void the warranty.] SAVE THESE INSTRUCTIONS www.lakeland.co.uk SV800UKL 54_E_IB_111004_1.indd 3 3 11-10-04 4:05 PM ASSEMBLY H I J A B K fig. 2 fig. 1 D C E F G fig. 3 VACUUM COMPONENTS ASSEMBLY A Main Body / Hand Vac 1 Insert the motorized brush into the vacuum body. B Handle C Dust Cup D Dust Cup Release E Motorized Brush F Crevice Tool 2 Insert the handle pole into the top of the main body. 3 Store the crevice tool on the back of the main body. G Charging Adapter 4 E nsure that the dust cup is securely in place. H Handle Release CHARGING I 1 The charge adapter plug will fit into the unit only one way. Insert the charging adapter plug by aligning the arrow on the plug with the arrow next to the charging jack on the back of the unit. (fig 1) Charging Jack J ON/OFF switch K Attachment Release TECHNICAL SPECIFICATIONS: Ni-Mh 1800mAh 10.8 V (1.2VDC x 9) 4 2 Charge the unit for 24 hours before using the vacuum for the first time. 3 Make sure the On/Off switch is in the Off position (O) before plugging in the charge adapter. (fig. 2) 4 The charging light will illuminate when the charge adapter is plugged in properly. (fig. 3) 5 After the initial 24-hour charge, the time for a complete charge is 16 hours. If you forget to switch the vacuum Off, it will still charge in the On position. But once the charge is complete, you must turn the switch Off before the unit will turn on again. www.lakeland.co.uk SV800UKL 54_E_IB_111004_1.indd 4 11-10-04 4:05 PM USING YOUR SHARK ® CORDLESS STICK VACUUM USE YOUR CORDLESS STICK VACUUM TO CLEAN BARE FLOORS, CARPETS, RUGS, UPHOLSTERY AND MORE. 1 Place your foot lightly on the top of the motorized brush and tilt the handle back to release the unit from the locked upright position. (fig. 4) BARE FLOOR CLEANING OFF CARPET CLEANING • Push the switch to the “|” side to turn the vacuum on to a speed optimized for bare floor cleaning. On the bare floor setting, the approximate run time is 12 minutes. • Push the switch to the “||” side to turn the vacuum on to a speed optimized for carpet cleaning. On the carpet setting, the approximate run time is 10 minutes. MAXIMIZING THE LIFE OF YOUR BATTERY 3 Charge the vacuum for a minimum of 16 hours. 1 To enhance battery life, this vacuum is equipped with an advanced feature that will shut off the vacuum when the battery is almost fully discharged. If the vacuum shuts off while in use, turn the power off and charge the unit for 16 hours. For other ways to improve vacuum performance, see page 8 for filter and brush roll maintenance. 2 Charge the vacuum for 24 hours before initial use and 16 hours for each recharge. Leaving the unit plugged in longer than the 16-hour charge time will not damage the batteries. 3 If the vacuum has never been used or has not been used for an extended period of time, it will take 3 to 5 16hour charges and full run down cycles to realize the full operational time of the vacuum. 4 Do not store in areas of high temperature or humidity 5 Use only adapter model number HK-AC-160A020-GB supplied by the manufacturer. If other chargers are used, the battery can fail causing damage to the battery, to the vacuum, or to personal property. BATTERY RECONDITIONING If you experience shorter run time over the life of the vacuum, perform the following battery reconditioning steps. These steps can also be performed as monthly maintenance for maximum battery life. 1 Charge the vacuum for a minimum of 24 hours. 2 Run the vacuum until it turns itself off. BATTERY REMOVAL, REPLACEMENT AND DISPOSAL The cordless stick vacuum is powered by Ni-Mh batteries, which must be recycled or disposed of properly in accordance with state, federal and local laws. If uncertain as to how to remove the battery pack, we suggest that you take your stick vacuum to a reputable small appliance service technician to have this service performed. fig. 4 • Push the switch to the “O” to turn the unit off. BATTERY REPLACEMENT 1 Connect the terminal on the white wire of the new battery pack to the terminal on the white wire inside the battery compartment. Firmly push them together, ensuring they are completely connected such that the black parts of the terminals are touching. Do the same for the red wires. Place the new battery pack into the battery compartment, label side facing out 2 Take care to tuck the wiring completely in so that the wiring does not interfere with the battery cover. BATTERY REMOVAL 3 Insert the battery cover bottom side first, then push in the top and replace the screws on either side. 1 E nsure that the unit is Off and not plugged into the charger. CAUTION: 2 • Use only with battery pack supplied. •  ever use ordinary batteries for N replacement as these may leak and damage your vacuum •  o not attempt to remove the battery D pack from the unit to charge. •  ever throw the battery pack or the N appliance into a fire or incinerate it. •  o not remove or damage the battery D casing. •  o not place the batteries on metal D surfaces. •  o not touch metal parts of the D batteries together as the batteries will overheat.  ever open the battery compartment N except to replace or dispose of the battery pack. Remove the two screws on either side of the battery cover on the back of the unit. Set the cover and the screws aside. 3 Carefully lift the battery pack from the bottom and slide it out of the compartment. 4 Grasp the terminals on the white wires and pull firmly to disconnect. Do the same for the red wires, taking care not to touch the wires together. 5 The battery pack must be recycled or disposed of properly in accordance with local regulations. Call customer service at FREEPHONE 0800 862 0453 to order a replacement battery pack. www.lakeland.co.uk SV800UKL 54_E_IB_111004_1.indd 5 5 11-10-04 4:05 PM USING YOUR SHARK ® CORDLESS STICK VACUUM fig. 7 fig. 6 fig. 5 YOUR CORDLESS STICK VACUUM IS A VERSATILE TOOL THAT ADJUSTS TO YOUR CLEANING NEEDS. 2 Convert the stick vacuum to a hand vacuum for a compact cleaning machine to use in your home, car, boat or RV. 1 Convert the stick vacuum to an extended reach crevice tool to clean really tough-to-reach places. • Turn off the vacuum. • Turn off the vacuum. • Press the attachment release button and remove the motorized brush. (fig. 5) • Insert the crevice tool into the bottom of the vacuum and snap it into place. (fig. 6) 3 To convert back to a stick vacuum: • Turn off the vacuum. • Insert the handle into the vacuum body. • Press the handle release and remove the handle. (fig. 7) • Press the attachment release button and remove the motorized brush. • Press the attachment release button and remove the crevice tool. • Insert the motorized brush into the bottom of the vacuum and snap it into place. • Insert the crevice tool into the bottom of the vacuum and snap it into place. You’re ready to reach under tables and along base boards with ease. 6 www.lakeland.co.uk SV800UKL 54_E_IB_111004_1.indd 6 11-10-04 4:05 PM CARE AND MAINTENANCE fig. 8 fig. 10 fig. 9 CAUTION: unplug the charging adapter from outlet before any servicing. EMPTYING THE DUST CUP  To maintain the best performance of your vacuum, empty the dust cup after every use or as debris approaches the “MAX FILL” line. Never operate the vacuum without the dust cup and filter in place. 1 Turn off the vacuum before removing the dust cup. 2 Press up the dust cup release button (fig. 8) and pull out the dust cup. fig. 11 3 R  emove the dust cup cover by twisting it so that the arrowhead on the dust cup aligns with the unlocked padlock on the dust cup cover and pulling up. (fig. 9) 6 R  eplace the dust cup into the vacuum by first pushing in the top part of the dust cup, then swinging in the bottom part and pushing it until it clicks. (fig. 11) 4 E mpty the dust cup in a garbage can, tapping it gently on the edge of the can to dislodge all the debris. 5 To reattach the dust cup cover, align the arrowheads printed on the dust cup and dust cup cover and twist so that the arrowhead on the dust cup is aligned with the locked padlock image on the dust cup cover. (fig. 10) www.lakeland.co.uk SV800UKL 54_E_IB_111004_1.indd 7 7 11-10-04 4:05 PM CARE AND MAINTENANCE - cont. filter frame foam filter dust cup cover fig. 13 fig. 12 CLEANING THE FILTER To ensure your vacuum lives a long and healthy life, it is important to regularly clean the filter. A dirty filter will result in poor suction and could overheat the motor. We recommend cleaning the filter each time the battery fully runs down. 1 T urn off the vacuum and remove the dust cup by pressing up on the dust cup release button. 2 Pull the filter frame out from the top of the dust cup cover and remove the foam filter from inside. (fig. 12) 8 fig. 14 3 R  inse the filter in lukewarm water and squeeze the water out. (fig. 13) CLEANING THE MOTORIZED BRUSH AND CLEARING BLOCKAGES 4 Let it air dry for 24 hours An accumulation of hair, string, and other debris may sometimes become caught and wrapped around the rotating brush. The motorized brush must be free from debris for maximum cleaning performance. To clean the brush roll and clear blockages:  DO NOT use a hair dryer or other forced hot air to dry the filter. 5 When the foam filter is completely dry, reinsert it into the filter frame and put the frame back into the top of the dust cup cover. (fig. 14) 1 Turn off the vacuum. 2 Press the attachment release button and remove the motorized brush. (fig. 15) www.lakeland.co.uk SV800UKL 54_E_IB_111004_1.indd 8 11-10-04 4:05 PM fig. 16 fig. 15 3 Make sure you are working in a well-lit area and turn the motorized brush over so you can see the rotating brush clearly. 4 Inspect the rotating brush for a build-up of debris. Remove anything wound around the brush by carefully cutting it with scissors. The brush roll is equipped with a raised cutting guide to make inserting scissors easier. Avoid damaging or cutting the bristles. (fig. 16) fig. 17 5 Use a flashlight to inspect the neck of the motorized brush and inside the air duct at the bottom of the main body and remove any debris or blockages. 6 R  eattach the motorized brush, ensuring that it clicks into place. (fig. 17) RESTARTING AFTER A JAM If your motorized brush becomes jammed, it will cease to operate. 1 Turn the unit off and allow it to cool down for two minutes. 2 E nsure that nothing is blocking the motorized brush or wrapped around the brush bar. 3 Turn the power on and the unit should operate normally. www.lakeland.co.uk SV800UKL 54_E_IB_111004_1.indd 9 9 11-10-04 4:05 PM TROUBLESHOOTING GUIDE & REPLACEMENT PARTS PROBLEM SUGGESTED SOLUTION Vacuum will not operate 1 The battery may be depleted. Charge for 16 hours, and ensure that the red charging indicator illuminates when the unit is plugged in. 2 See “Restarting after a jam” on page 9. Charging indicator does not illuminate 1 Check to see if the charge adapter is plugged in properly to the outlet and to the unit. 2 E nsure that the electrical outlet is supplying power to the charger. Check the fuse/breaker. 3 Ensure that the power switch is in the Off position (O). Motorized brush will not work 1 S ee “Cleaning the Motorized Brush and Clearing Blockages” on page 8 and “Restarting after a jam” on page 9. 2 The belt may need to be replaced. See “Replacement Parts” below. 3 Ensure that the motorized brush is properly attached. Vacuum will not pick up or suction power is weak 1 Empty the dust cup container. 2 R  emove the dust cup filter, check for blockages and remove. Clean or replace the dust cup filter (See “Replacement Parts” below). Note: It is important to clean the dust cup filter regularly. 3 The battery may need to be charged, charge for 16 hours. 4 Ensure that the motorized brush or crevice tool is properly attached. Dust escapes from vacuum 1 Empty the dust cup container. 2 R  eview the dust cup filter installation instructions to ensure that the filter is installed correctly. 3 Check for punctures in dust cup filter or cracks in the dust cup and replace (See “Replacement Parts” below). Vacuum turns off on its own 1 See “Restarting after a jam” on page 9. Run time has decreased over time 1 Perform the following steps: 10 a Charge the vacuum for a minimum of 24 hours. b Run the vacuum until it turns itself off. c Charge the vacuum for a minimum of 16 hours. www.lakeland.co.uk SV800UKL 54_E_IB_111004_1.indd 10 11-10-04 4:05 PM NOTES www.lakeland.co.uk SV800UKL 54_E_IB_111004_1.indd 11 11 11-10-04 4:05 PM Shark Customer Service PO Box 298 Mirfield WF14 9BA Freephone 0800 862 0453 www.lakeland.co.uk COPYRIGHT© EURO-PRO OPERATING LLC 2011 PRINTED IN CHINA SV800UKL.E.111004.1 Illustrations may differ from actual product. SV800UKL 54_E_IB_111004_1.indd 12 11-10-04 4:05 PM