Transcript
SYNERGY
RACK MOUNT
KIT TO ACCOMMODATE DOOR
1x 5/32” Hex Key - (400-080) 1x
300-520 300-518
OPTION: INSTALLING GEAR FORWARD Rack rails may also be installed with the flange forward in applications the door is not desired and additional cabinet
1/8” Hex Key - (400-070)
depth is needed.
A.
Place the 1/2” Button Head Screw (300-485) in the holes of rack mount rail and hinge bracket and loosely screw to Flat-nut (300-560).
Note: Rackmount brackets that have a triangle must locate at the top.
B.
Slide Rack Mount Rail into position with the Flat Nuts sliding into the channel as shown. After bracket is in position tighten all screws with hex key.
12x (300-485) 1/2” Button Head Screw
2x (301-360) Mounting Screw
8x
(300-560) - Flat Nut
Limited Warranty
For five full years Salamander Designs Ltd. will repair or replace, at our option, any product defective in materials or craftsmanship. Salamander Designs Ltd. will not be responsible for any damage to or destruction of other equipment consequential to our equipment failure. Defective product must be given Return Authorization and is to be returned to the factory prepaid, in the original carton and packing material. Any damage incurred in a shipment not in original packaging shall be the responsibility of the owner. Warranty repairs will be returned prepaid, via UPS within the continental U.S.A. only.
www.SalamanderDesigns.com 800-535-5659 Doc No. 500-455 / v11.10 ©2010 Salamander Designs Ltd.
C.
Snap door onto hinge bases align top and bottom gap and tighten.
For 15 and 21U rails: D.
Install header panel at the top same location of rack mount.
SYNERGY
RACK MOUNT 1x 5/32” Hex Key - (400-080) 1x
OPTION: INSTALLING GEAR FORWARD Rack rails may also be installed with the flange forward in applications the door is not desired and additional cabinet depth is needed.
A For Installing in Synergy Cabinets: 1/8” Hex Key - (400-070)
B
Place the 1/2” Button Head Screw (300-485) in the holes of each bracket and attach loosely with Flat Nut. Note: For assembled cabinets use the Drop-In Nut in place of the Flat Nut. For Installing in Chameleon Cabinets: Use the Drop-In Nuts (300-565) and the shorter 3/8” Button Head Screws (300-518). Insert Flat Nut s or Drop-In Nuts into the channels (Use the Front Side Channel for Chameleon). Secure screws with Hex Key.
C Use standard 10-32 mounting screws to mount equipment on rack rails. D For 15U & 21U Rails, attach header panel at the top of the rack rail.
6x
300-565 > or 300-560 >
< 300-485 or 300-518
(300-518) 3/8” Button Head Screw
8x
12 x
(300-485) 1/2” Button Head Screw
(301-360) Mounting Screw
8x
4x
Note: Use the front side channel for Chameleon Cabinets
(300-560) - Flat Nut
CABINET FRONT (300-565) Drop-In Nut
Limited Warranty
For five full years Salamander Designs Ltd. will repair or replace, at our option, any product defective in materials or craftsmanship. Salamander Designs Ltd. will not be responsible for any damage to or destruction of other
NOTES Installing Gear Forward
For Small Segment Use Behind Door
Rack rails may also be installed with the flange forward in applications the door is not desired and additional cabinet depth is needed.
Install brackets away from door hinges.
equipment consequential to our equipment failure. Defective product must be given Return Authorization and is to be returned to the factory prepaid, in the original carton and packing material. Any damage incurred in a shipment not in original packaging shall be the responsibility of the owner. Warranty repairs will be returned prepaid, via UPS within the continental U.S.A. only.
www.SalamanderDesigns.com 800-535-5659 Doc No. 500-455 / v11.10 ©2010 Salamander Designs Ltd.
FRONT
SYNERGY TRIPLE UNIT - SL20 / SL30 / SL40 !
WARNING: If you are installing accessories such as doors or drawers to the base unit, read all instructions for the accessory and install in conjunction with these instructions.
CONNECTOR BOLTS ALUMINUM POSTS TOP SHELF
(A) SHELF PEGS
BOTTOM SHELF
(B)
ADJUSTABLE SHELVES
WASHER HEX NUT LEVELER FOOT
* Diagram: Synergy 30 Triple Unit
Doc No. 500-780 v6.05
TRIPLE - 1 of 4
Parts
1x (400-060) - 3/16” Hex Key
8 - Aluminum Posts
Adjustable Shelf (SL20 -3) • (SL30 - 6)
1 - Top Shelf
1 - Spacer Tool
8x
1 - Bottom Shelf 3 - Rear Panels
8x
1x (400-035) - Wrench
Rear Panel Bags - PHK-240
8x 1x
(400-070) - 1/8” Hex Key
12x
(300-540) Connector Bolt
(300-470) Washer
(300-510) - Stud
12x
12x
(P-300-320) - Leveler Foot
1x (300-560) - Flat Nut
(300-530) - ThumbNut
(PHK-380) Shelf Peg “A” SL20 - 6x SL30 - 12x
(PHK-370) Shelf Peg “B” SL20 -6x SL30 -12x
(P-400-040) - Level
Limited Warranty For five full years Salamander Designs Ltd. will repair or replace, at our option, any product defective in materials or craftsmanship. Salamander Designs Ltd. will not be responsible for any damage to or destruction of other equipment consequential to our equipment failure. Defective product must be given Return Authorization and is to be returned to the factory prepaid, in the original carton and packing material. Any damage incurred in a shipment not in original packaging shall be the responsibility of the owner. Warranty repairs will be returned prepaid, via UPS within the continental U.S.A. only.
Salamander Designs Ltd. 800-535-5659 ©2003 Salamander Designs Ltd.
® Synergy System - U.S.A. Patented.
www.SalamanderDesigns.com Doc No. 500-780 v6.05
TRIPLE - 2 of 4
1 Connect Posts to Bottom Shelf !
2 Add Shelf Pegs !
WARNING: Tighten by screwing the leveler foot NOT the post.
A. Square Post
B. Connect Post
Square the post to the bottom shelf.
Screw foot with metal washer through bottom shelf and onto the end of an extruded post. Hand tighten fully then use wrench on hex nut to tighten nut onto underside of shelf.
O
90
WARNING: If you are installing an optional door or drawer refer to specific instructions before proceeding.
A. Insert all shelf pegs down each post.
B. Washer
Gently tighten pegs with the hex key to desired position.
Hex Nut Foot
A
B A
B
Doc No. 500-780 v6.05
TRIPLE - 3 of 4
3 Adjust Shelf Pegs & Add Shelves
EX R EA
ED N D EL TEP A N R
3 4
40 / S EL 0 AN S3 R P R EA
Combine the 1” threaded studs with the flat nuts. Slide hardware into rear posts.
2 5
2X
4X
4X
2X
1 2 3
www.salamanderdesigns.com
EXTENDED REAR PANEL
Use the Spacer Tool to align top and bottom studs.
S20 / SVDO REAR PANEL
SPACER TOOL
1
Insert peg down the post channel and position the peg through the Spacer and tighten. You may also consider using books or CD's for shelf spacing.
A. Insert & Align Studs www.salamanderdesigns.com
Adjusting Shelves
8
O VD / S EL 0 AN S2 R P R EA
A.
4 Attach Rear Panel & Top Shelf
S30 / S40 REAR PANEL
4 5
4 1/2 " 6 7
8" 9 8
TOOL
6
7
8
TOOL
SPACER
9
6"
SPACER
7
6"
5
6
4 1/ 2 "
4
5
3
1
EXTENDED REAR PANEL
2
S20 / SVDO REAR PANEL
EXTENDED REAR PANEL
1
3 2
S20 / SVDO REAR PANEL
www.salamanderdesigns.com
S30 / S40 REAR PANEL
www.salamanderdesigns.com
4
S30 / S40 REAR PANEL
REAR
300-540
Insert the top 8 connector bolts and tighten down top shelf. 8
TOOL
SPACER
9
8"
6
7
6"
4
5
4 1/2 "
2
3
S30 / S40 REAR PANEL
S20 / SVDO REAR PANEL
EXTENDED REAR PANEL
1
Place shelves from the bottom up. Angle the shelf in between the front post and set on top of shelf pegs and heavy duty brackets.
8"
8"
4 1/ 2 "
www.salamanderdesigns.com
B. Placing Shelf
6" 9
Before enclosing the unit with the top shelf install side panels (if applicable). See Side Panel Instructions
B. Install Top
8
TOOL
SPACER
Side Panels
C. Secure Rear Panel Place panels and secure thumb nuts to finish rear panel installation.
* Use holes to guide the studs..
C. Fine Tuning Use the bubble level to precisely adjust the shelves. Be sure to level both side to side as well as front to back. Use the hex key to tighten each peg.
TIP To ease installation of rear panels first remove any drawers and/or doors and gently place the unit face down on the floor to improve aligning of panels.
Doc No. 500-780 v6.05
TRIPLE - 4 of 4
