Transcript
Instruction Manual for ®
Side-to-Side Reciprocating Handpiece
Model: New SZX Profiler #510-2245
Power Hand 2X controllers and handpieces combine to create the most versatile finishing system in the industry, offering rotary, profiling and belt sanding action.
Power Hand 2X component selection:
• Three controllers • Six straight (four standard, two slimline) and two angle rotaries
• Two reciprocating profilers • One side-to-side profiler • One belt sander • One 4:1 reduction gear • Separate motors and handpiece heads Safety Recommendations — Prolonged use of vibrating or reciprocating tools may result in vibration-induced circulation problems in the hands. Always follow safe operating procedures. Using hand protection (i.e., insulated gloves) and taking frequent breaks can help minimize but not guarantee against injury. Operating these types of tools in cold weather or with a tight grip will reduce the period of operation before risking potential injury. Individuals with a tendency to suffer from poor circulation, frequently cold fingers or itchy hands should closely monitor the condition of their hands. If symptoms appear, seek medical advice immediately.
Gesswein
®
The Right Tools
201 Hancock Ave., Bridgeport, CT 06605, USA 1-203-366-5400 FAX 1-203-366-3953 Order toll-free 1-800-243-4466 ☎ Web site: www.gesswein.com E-mail:
[email protected] #890-2049/0812
Introduction The Gesswein New SZX Profiler is engineered and manufactured to a high degree of precision and will provide many years of trouble-free service. Backed by a limited warranty that covers wear parts for 90 days and overall balance of parts for six months. The DC electrically driven handpiece is designed to be used with the Power Hand 2X Single, Standard, Dual, Jewelers’ Micromotor, Power Carver II and BrightCutting Controllers. These controllers convert the alternating current (AC) power supply to a variable direct current (DC) by means of an I.C. transistorized automatically controlled circuit. The Gesswein Power Hand 2X handpiece series consists of nine models and eleven head assemblies with maximum operating speeds ranging from 8,000 to 55,000rpm and 0 to 117 strokes per second. All models are identified by their names, which are engraved on the motor housings.
Specifications Strokes per Second
Dual or Single Controller* Standard Controller Input Voltage
0-133 32-133 3-30V DC
Max. Shaft Output (W/sec.)
Dual Controller Standard Controller Single Controller
36 – 33
Max. Stoppage Torque (ft.-lbs./N-m**)
Dual Controller Standard Controller Single Controller Net Wt. (without power cord)
0.054/0.073 0.047/0.064 0.053/0.072 10 oz.
*Or Standard Controller with variable-speed foot rheostat **Foot-pounds/Newton-meters
2
11
New Z-SZX Parts List
1. Accessories
When ordering spare parts, always specify part# (or item# if applicable) and description.
Included Accessories
Part#
B. One Tool Pin
Item#
Description
A. One Allen Wrench
New Z-M08X-101
Motor Case
New Z-M08X-102
Countersunk Head Screw
New Z-M08X-103
Rubber O-Ring
New Z-M08X-104
Spacer
Optional Accessories
New Z-M08X-105
Spacer
New Z-M08X-106
Wave Washer
A. Handpiece Extension Cord (#510-1120): adds 1.5m to the 1.7m New SZX Profiler cord
New Z-M08X-200
510-2322
Armature Complete
New Z-M08X-201
510-3087
Ball Bearing
New Z-M08X-202
Spacer
New Z-M08X-203
Spacer
New Z-M08X-204
510-2323
Armature
New Z-M08X-205
510-3073
Ball Bearing
New Z-M08X-301
Rubber O-Ring
New Z-M08X-302
Spacer
New Z-M08X-303 New Z-M08X-304
Rear Lid 510-0161
Carbon Brushes (one set)
New Z-M08X-305
(+) Terminal Plate
New Z-M08X-306
Brush Side Lid
New Z-M08X-307
(–) Terminal Plate
New Z-M08X-308
Pan Head Screw
New Z-M08X-309
Motor Cord with Plug
New Z-M08X-310
Motor Cover
C. One Assortment of Tool Holders, Bamboo Laps, PSA Chips and Felt Pads
B. Handpiece Cradle Rest (#510-1130): provides safe holding place for handpiece when not in use C. Variable-Speed Foot Rheostat (#510-3100) D. On/Off Foot Switch (#510-3105)
2. Parts Nomenclature 1. Swing Arm (Tool Holder) 2. Swing Arm Pivot Point indicated by a red ring 3. Top Cover
11
2
3
4
12
5
4. Knurled Ring 5. Motor Cover 6. Electric Cord with 3-Pin Plug
6
1
7. Main Eccentric Shaft 8. Stroke Adjustment Screw (Hex Socket Set Ring) 9. Knurled Adjusting Ring
9
7
10. Drive Bearing 11. Tool Securing Screw 12. Motor Connecting Ring 13. Nylon Shoe 10
10
8
3
13
3.
Stroke Adjustment
The New SZX Profiler has an adjustable stroke of 0-1.6mm, measured at the Tool Holder. However, the stroke will be greater at the tool end. To adjust stroke, first remove the top cover by firmly grasping the knurled ring (see fig. 2) and unscrewing in a counterclockwise direction. Completely remove the top cover from the handpiece motor. Next, loosen the Hex Socket Set Screw (see fig. 3) located on the side of the main eccentric shaft using the Allen Wrench provided. Now line up the mark on the Knurled Adjusting Ring with the stroke setting marked in millimeters on the side of the main shaft. Finally, tighten the Hex Socket Set Screw, and firmly secure the handpiece Top Cover to the motor by screwing in a clockwise direction.
Top Cover
Tighten
Fig. 2
Hexagon Key Wrench
Loosen
Tighten
4
.
0
4. Tool Attachment
Loosen
.
80
Loosen the Tool-Securing Set Screw located on the Swing Arm (Tool Holder) using the Tool Pin provided. Place the tool into the Tool Holder and fasten securely (see fig. 4).
Fig. 3
Loosen Tighten
Tool
Fig. 4 4
9
New Z-SZX Parts List
5. Operating Procedure
When ordering spare parts, always specify part# (or item# if applicable) and description.
With your New SZX Profiler adjusted for stroke and with a selected tool fitted, connect the Gesswein Power Hand Controller to an electrical supply and the Profiler to controller.
Part#
Item#
Description
Z-SWX-101
Top Cover
Z-SWX-102
Oval Countersunk Set Screw (M2. 6 x 6)
Z-SWX-200
Swing Arm Completed
Z-SWX-201
Swing Arm Support B
Z-SWX-202
Swing Arm
Z-SWX-203
Tool Securing Screw
Z-SWX-204
Swing Arm Support A
Z-SWX-300
Eccentric Shaft Completed
Z-SWX-301
E-Type Clip Ring
Z-SWX-302
Ball Bearing
Z-SWX-303
Eccentric Shaft
Z-SWX-400
Main Shaft Completed
Z-SWX-401
Main Shaft
Z-SWX-402
Coil Spring
Z-SWX-403
Joint
Z-SWX-404
C-Type Clip
Z-SWX-405
Teflon Spacer
Z-SWX-406
Ball Bearing
Z-SWX-407
O-Type Rubber Ring
Z-SWX-408
Bearing Spacer
Z-SWX-409
C-Type Clip Ring
Z-SWX-420
Hexagon Socket Set Screw (M3 x 4)
Z-SWX-501
C-Type Clip Ring
Z-SWX-502
Wave Washer
Z-SWX-503
Lock Ring Completed
Z-SWX-002
Hexagon Key Wrench
8
Set the Slide Rheostat on the Controller to “Low” or the “0” position. Put the Controller Main Switch to the “ON” position, which lights up a pilot light that indicates your New SZX Profiler is ready to use. To increase the speed of the New SZX Profiler, move the Slide Rheostat toward High or “10” and the desired reciprocating frequency. You can now begin working. When work is completed, put the Main Switch to “OFF.” To operate your handpiece using the optional Variable-Speed Foot Rheostat or optional On/Off Foot Switch, please refer to the Power Hand 2X Controller Instruction Manual for proper connection. The handpiece will not run until the foot rheostat/switch is depressed. The rheostat provides infinitely variable speed control; the switch only turns the handpiece on and off (operates at speed selected on controller).
5
6. Precautions
Replacement of Carbon Brushes
A. Do not allow a tool to hammer excessively against a sidewall that is not being polished or the handpiece bearings will be damaged. B. Make sure that the Top Cover is securely tightened; a loose cover will cause excessive vibration and wear on bearing surfaces. C. Always unplug the New SZX Profiler from the Power Hand Controller by gripping the plug end, not the cord. D. Be sure the air cooling vents, located under the rear cover, are kept open and free of dust and grit. E. Do not allow abrasive particles or oil-abrasive slurry to enter the spindle and Top Cover of the handpiece or handpiece motor. F. In the event the entire Swing Head of the handpiece must be removed from the motor assembly, grasp the Motor Connecting Ring (see fig. 1) and pull upward. To replace, again pull upward on the Motor Connecting Ring and fit
The motor in the New SZX Profiler uses a spring tension-type carbon brush assembly. The approximate life of the brushes is 800-1,000 hours. Use the set of two replacement carbon Brushes supplied with your handpiece when it becomes necessary to replace worn brushes. (Brushes should be changed when handpiece is not running at maximum speed, or if it sounds as though it’s running out of gas.) Please note that in the event you must change the brushes, it is important that both be replaced at the same time. Replacement of only one carbon brush will cause motor damage. To replace worn carbon brushes, disconnect the Motor Cover by unscrewing it in a counterclockwise direction. The motor brushes are now exposed. The worn brush assemblies can be removed by using a small Phillips head screwdriver on the screws that secure the assemblies (see fig. 6). The brush spring mount will push the assembly out of the well so that it can then be lifted clear. The two new carbon brushes should be installed by gently pushing them into the brush well. When each assembly has been screwed in securely, replace the Motor Cover and Power Cord.
Maintenance Dust Removal
Carbon Brush
From time to time it is necessary to clean the excessive dust that accumulates in the Motor Cover. Unfasten the Motor Cover in a counterclockwise direction, and remove excessive dust with a dry brush. If necessary, use a moistened cloth with detergent. Never use thinners or alcohol.
Screw
Lubrication Occasionally apply a small amount of Molybdenum grease to the Nylon Drive Shoe located under the Top Cover. (see fig. 5).
Loosen
Tighten
Motor Cover Nylon Drive Shoe
Fig. 5
Fig. 6
6
7
6. Precautions
Replacement of Carbon Brushes
A. Do not allow a tool to hammer excessively against a sidewall that is not being polished or the handpiece bearings will be damaged. B. Make sure that the Top Cover is securely tightened; a loose cover will cause excessive vibration and wear on bearing surfaces. C. Always unplug the New SZX Profiler from the Power Hand Controller by gripping the plug end, not the cord. D. Be sure the air cooling vents, located under the rear cover, are kept open and free of dust and grit. E. Do not allow abrasive particles or oil-abrasive slurry to enter the spindle and Top Cover of the handpiece or handpiece motor. F. In the event the entire Swing Head of the handpiece must be removed from the motor assembly, grasp the Motor Connecting Ring (see fig. 1) and pull upward. To replace, again pull upward on the Motor Connecting Ring and fit
The motor in the New SZX Profiler uses a spring tension-type carbon brush assembly. The approximate life of the brushes is 800-1,000 hours. Use the set of two replacement carbon Brushes supplied with your handpiece when it becomes necessary to replace worn brushes. (Brushes should be changed when handpiece is not running at maximum speed, or if it sounds as though it’s running out of gas.) Please note that in the event you must change the brushes, it is important that both be replaced at the same time. Replacement of only one carbon brush will cause motor damage. To replace worn carbon brushes, disconnect the Motor Cover by unscrewing it in a counterclockwise direction. The motor brushes are now exposed. The worn brush assemblies can be removed by using a small Phillips head screwdriver on the screws that secure the assemblies (see fig. 6). The brush spring mount will push the assembly out of the well so that it can then be lifted clear. The two new carbon brushes should be installed by gently pushing them into the brush well. When each assembly has been screwed in securely, replace the Motor Cover and Power Cord.
Maintenance Dust Removal
Carbon Brush
From time to time it is necessary to clean the excessive dust that accumulates in the Motor Cover. Unfasten the Motor Cover in a counterclockwise direction, and remove excessive dust with a dry brush. If necessary, use a moistened cloth with detergent. Never use thinners or alcohol.
Screw
Lubrication Occasionally apply a small amount of Molybdenum grease to the Nylon Drive Shoe located under the Top Cover. (see fig. 5).
Loosen
Tighten
Motor Cover Nylon Drive Shoe
Fig. 5
Fig. 6
6
7
New Z-SZX Parts List
5. Operating Procedure
When ordering spare parts, always specify part# (or item# if applicable) and description.
With your New SZX Profiler adjusted for stroke and with a selected tool fitted, connect the Gesswein Power Hand Controller to an electrical supply and the Profiler to controller.
Part#
Item#
Description
Z-SWX-101
8960230
Top Cover
Z-SWX-102
8960231
Oval Countersunk Set Screw
Z-SWX-200
8960232
Swing Arm Complete
Z-SWX-201
8960233
Swing Arm Support B
Z-SWX-202
8960234
Swing Arm
Z-SWX-203
8960235
Tool-Securing Screw
Z-SWX-204
8960236
Swing Arm Support A
Z-SWX-300
Eccentric Shaft Complete
Z-SWX-301
8960156
E-Type Clip Ring
Z-SWX-302
5103076
Ball Bearing
Z-SWX-303
8960238
Eccentric Shaft
Z-SWX-400
8960241
Main Shaft Complete
Z-SWX-401
8960242
Main Shaft
Z-SWX-402
8960067
Coil Spring
Z-SWX-403
5100151
Nylon Coupler (Joint)
Z-SWX-404
8960068
C-Type Clip
Z-SWX-405
8960243
Teflon Spacer
Z-SWX-406
5103079
Ball Bearing
Z-SWX-407
8960244
O-Type Rubber Ring
Z-SWX-408
8960245
Bearing Spacer
Z-SWX-409
8960246
C-Type Clip Ring
Z-SWX-420
8960240
Hexagon Socket Set Screw
Z-SWX-501
8960239
C-Type Clip Ring
Z-SWX-502
8960247
Wave Washer
Z-SWX-503
8960248
Lock Ring Completed
Z-SWX-002
8960249
Hexagon Key Wrench
8
Set the Slide Rheostat on the Controller to “Low” or the “0” position. Put the Controller Main Switch to the “ON” position, which lights up a pilot light that indicates your New SZX Profiler is ready to use. To increase the speed of the New SZX Profiler, move the Slide Rheostat toward High or “10” and the desired reciprocating frequency. You can now begin working. When work is completed, put the Main Switch to “OFF.” To operate your handpiece using the optional Variable-Speed Foot Rheostat or optional On/Off Foot Switch, please refer to the Power Hand 2X Controller Instruction Manual for proper connection. The handpiece will not run until the foot rheostat/switch is depressed. The rheostat provides infinitely variable speed control; the switch only turns the handpiece on and off (operates at speed selected on controller).
5
3.
Stroke Adjustment
The New SZX Profiler has an adjustable stroke of 0-1.6mm, measured at the Tool Holder. However, the stroke will be greater at the tool end. To adjust stroke, first remove the top cover by firmly grasping the knurled ring (see fig. 2) and unscrewing in a counterclockwise direction. Completely remove the top cover from the handpiece motor. Next, loosen the Hex Socket Set Screw (see fig. 3) located on the side of the main eccentric shaft using the Allen Wrench provided. Now line up the mark on the Knurled Adjusting Ring with the stroke setting marked in millimeters on the side of the main shaft. Finally, tighten the Hex Socket Set Screw, and firmly secure the handpiece Top Cover to the motor by screwing in a clockwise direction.
Top Cover
Tighten
Fig. 2
Hexagon Key Wrench
Loosen
Tighten
4
.
0
4. Tool Attachment
Loosen
.
80
Loosen the Tool-Securing Set Screw located on the Swing Arm (Tool Holder) using the Tool Pin provided. Place the tool into the Tool Holder and fasten securely (see fig. 4).
Fig. 3
Loosen Tighten
Tool
Fig. 4 4
9
New Z-SZX Parts List
1. Accessories
When ordering spare parts, always specify part# (or item# if applicable) and description.
Included Accessories A. One Allen Wrench
Part#
Item#
Description
B. One Tool Pin
UM20-316
8960001
Motor Case
YSF21-103
8960002
Countersunk Head Screw
C. One Assortment of Tool Holders, Bamboo Laps, PSA Chips and Felt Pads
ON10-301
8960003
O-Type Rubber Ring
Optional Accessories
KS-118
8960004
Metal Spacer
KS-119
8960005
Teflon Spacer
A. Handpiece Extension Cord (#510-1120): adds 1.5m to the 1.7m New SZX Profiler cord
KS-114B
8960006
Metal Spacer
KW-111
8960007
Wave Washer
1140ZZ
5103087
Ball Bearing
KS-085
8960008
Metal Spacer
C. Variable-Speed Foot Rheostat (#510-3100)
KS-119
8960005
Teflon Spacer
D. On/Off Foot Switch (#510-3105)
KA20-104-BB
5102322
Armature Completed
KA20-104
5102323
Armature
KF-203A
8960010
Dust Proof Collar
KF-210
8960011
Dust Proof Collar
1030ZZ
5103073
Ball Bearing
S-10
8960012
O-Type Rubber Ring
KS-101
8960013
Teflon Spacer
HE10A-203
8960014
Rear Lid
ON10-204
8960015
O-Type Rubber Ring
UM20-201
8960016
Brush Side Lid
PKE60-103
5100161
Carbon Brush (set of two pieces)
YSP23-103
8960017
Pan Head Screw
KE-126
8960018
(+) Terminal Plate
KE-127
8960019
(–) Terminal Plate
KE22-504
5100170
Motor Cord with Plug
UM20-761
8960020
Motor Cap Completed
UM20-561
8960021
Motor Cap
8. Stroke Adjustment Screw (Hex Socket Set Ring)
UM20-651
8960022
Plastic Cap Ring
9. Knurled Adjusting Ring
B. Handpiece Cradle Rest (#510-1130): provides safe holding place for handpiece when not in use
2. Parts Nomenclature 1. Swing Arm (Tool Holder) 2. Swing Arm Pivot Point indicated by a red ring 3. Top Cover
11
2
3
4
12
5
4. Knurled Ring 5. Motor Cover 6. Electric Cord with 3-Pin Plug
6
1
7. Main Eccentric Shaft
9
7
10. Drive Bearing 11. Tool Securing Screw 12. Motor Connecting Ring 13. Nylon Shoe 10
10
8
3
13
3. Operating Procedure with Standard Controller S-10
With your rotary handpiece fitted with a selected tool, connect the Gesswein Power Controller to an electrical supply and the handpiece to one of the two output sockets provided.
ON10-204
YSF21-103
HE10A-203
To increase the speed of the rotary handpiece, move the Slide Rheostat toward “High” or “10.” You can then begin working. When work is completed, put the Main Switch to “OFF.”
ON10-301 KS-118
KE-126
UM20-201
PKE60-103
KS-119 1140ZZ
KE22-504
KW-111
KS-114B
KE-127
YSP23-103
To operate your rotary handpiece using the optional Variable-Speed Foot Rheostat or optional On/Off Foot Switch, please refer to the Power Hand 2X Controller Instruction Manual for proper connection. The handpiece will not rotate until the foot rheostat/switch is depressed. The rheostat provides infinitely variable speed control; the switch only turns handpiece on and off (operates at speed selected on control unit).
UM20-316
KS-101
Set the Slide Rheostat on the Controller to “Low” or the “0” position. Put the Controller Main Switch to the “ON” position, which lights up a pilot light that indicates your rotary handpiece is ready to use.
KS-085 KS-119 KF-203A
KA20-104-BB
UM20-651
UM20-761
UM20-561
KA20-104
KF-210 1030ZZ
4
9
Instruction Manual for ®
Side-to-Side Reciprocating Handpiece
Model: New SZX Profiler #510-2245
Power Hand 2X controllers and handpieces combine to create the most versatile finishing system in the industry, offering rotary, profiling and belt sanding action.
Power Hand 2X component selection:
• Three controllers • Six straight (four standard, two slimline) and two angle rotaries
• Two reciprocating profilers • One side-to-side profiler • One belt sander • One 4:1 reduction gear • Separate motors and handpiece heads Safety Recommendations — Prolonged use of vibrating or reciprocating tools may result in vibration-induced circulation problems in the hands. Always follow safe operating procedures. Using hand protection (i.e., insulated gloves) and taking frequent breaks can help minimize but not guarantee against injury. Operating these types of tools in cold weather or with a tight grip will reduce the period of operation before risking potential injury. Individuals with a tendency to suffer from poor circulation, frequently cold fingers or itchy hands should closely monitor the condition of their hands. If symptoms appear, seek medical advice immediately.
Gesswein
®
The Right Tools
201 Hancock Ave., Bridgeport, CT 06605, USA 1-203-366-5400 FAX 1-203-366-3953 Order toll-free 1-800-243-4466 ☎ Web site: www.gesswein.com E-mail:
[email protected] #890-2049/0812
