Transcript
Hobby World Corporation
700RC T
GASSER CONVERSION
Kit Features: Powered by HWC G29RCE 3D Extreme or Zenoah 29cc RC style gasoline engines. Lightweight yet extremely strong carbon fiber frames. Extra large heavy duty clutch system for sustained power transfer. Aluminum side frame support structure for additional rigidity. 430cc fuel tank for long engine run time. Multiple point engine stabilization system. Slant gear pinion and main gear provide efficiency and strength. Heavy duty one-way auto-rotation hub and bearing. Beautiful, highly visible, lightweight, highly durable painted fiberglass canopy.
Exclusively distributed by Century Helicopter Products © 2013 Hobby World Corporation - All rights reserved.
Version 1.00
T700RC GASSER CONVERSION
INTRODUCTION Thank You
Congratulations on the purchase of the newest product that enables the conversion to gasoline power. This conversion kit was designed around the nitro version of the TREX 700 2011 model. There may be variances with earlier or future models so please thoroughly go through the instructions to ensure you have all the parts necessary to complete the conversion. This conversion kit will allow efficient and inexpensive flights with your helicopter using gasoline for fuel.
Warning
This radio controlled model is not a toy! It is a precision machine requiring proper assembly and setup to avoid accidents. It is the responsibility of the owner to operate this product in a safe manner as it can inflict serious injury otherwise. It is recommended that if you are in doubt of your abilities, seek assistance from experienced radio control modelers and associations. Keep loose items that can get entangled in the rotor blades away for the main and tail blades, including loose clothing, hair, or other objects such as pencils and screwdrivers. Especially keep your hands away from the rotor blades. As manufacturer, we assume no liability for the use of this product.
Flight Guidelines
Please note this checklist is not intended to be a replacement for the content included in this instruction manual. Although it can be used as a quick start guide, we strongly suggest reading through this manual completely before proceeding. Always turn the transmitter on first Allow the gyro, and receiver to arm and initialize properly Do a pre-flight check making sure all electronics are working and look for any mechanical issues Fly the model Land the model Turn off the engine Always turn the transmitter off last
General Guidelines
Apply thread lock to all metal to metal thread contact points. Do not apply CA (cyanoacrylate) glue or thread lock to ny-lock nuts (metal nuts with plastic inserts). Diagrams indicated by bounding boxes for screws, bearings, etc. are illustrated at a 1-to-1 ratio. All other illustrations are not drawn to scale. Throughout this manual, you will find building tips. Please follow the tips and use common sense when building.
Pre-assembly Information
Upon opening the kit, all the major component parts are bagged for ease of assembly which correspond to the sections of the manual. Various assemblies have been pre-assembled however, only as a reference assembly. Final assembly is up to the user. Installation onto the particular parts, screws and nuts required for each step are packaged in the same bag as the parts. Be careful when opening each bag as not to lose any hardware. Care has been taken in filling and packing of each bag however mistakes do happen. If there is a parts shortage or missing hardware please contact us at:
Hobby World Corporation No.2 Industrial District, Yang Wu, Da Ling Shan, Dong Guan, Guandong, China For support, please contact your local dealer/distributor.
Page 2
T700RC GASSER CONVERSION
REQUIRED ITEMS
6 CHANNEL RECEIVER (MINIMUM)
SERVOS X 5
6 CHANNEL CCPM TRANSMITTER (MINIMUM)
DREMEL TOOL OR SIMILAR
CN2034A BALL LINK PLIERS
HOBBY SCISSORS
CN2017* HEX DRIVERS 1.5, 2.0, 2.5, 3.0, 4.0, 5.0 CN2027 G-FORCE PITCH GAUGE
NEEDLE NOSE PLIERS
ELECTRONIC IGNITION BATTERY
SLOW & Medium CA GLUE
Medium (Medium) THREADLOCK
METRIC RULER OR SIMILAR MEASURING DEVICE
29cc RC ZENOAH GASOLINE ENGINE
ZIP TIES 690 - 720 MM MAIN ROTOR BLADES
CN2050 PADDLE GAUGE
RECEIVER BATTERY
GYRO
87 TO 92 OCTANE GASOLINE
CN3069C / CN3071 TORPEDO GASSER TUNED MUFFLER
4-WAY WRENCH
SYNTHETIC OIL/GREASE
2-STROKE MOTOR OIL
CN2051 ACCURATECH BLADE BALANCER V.2
CN2255 CONTROL ROD SETUP GAUGE
HOBBY KNIFE
Warranty Period Hobby World Corporation warranties that the Products purchased (the “Product”) will be free from defects in materials and workmanship 30 days from the date of purchase by the Purchaser.
Limited Warranty (a) This warranty is limited to the original customer (“Purchaser”) and is not transferable. REPAIR OR REPLACEMENT AS PROVIDED UNDER WARRANTY IS THE EXCLUSIVE REMEDY OF THE PURCHASER. This warranty covers only those Products purchased from an authorized Hobby World Corporation dealer. Third party transactions are not covered by this warranty. Proof of purchase is required for the warranty claims. Further, Hobby World Corporation reserves the right to change or modify this warranty without notice and disclaims all other warranties, express or implied. (b) Limitations – HOBBY WORLD CORPORATION MAKES NO WARRANTY OR REPRESENTATION, EXPRESS OR IMPLIED, ABOUT NONINFRINGEMENT, MERCHANTABILITY, OR FITNESS FOR A PARTICULAR PURPOSE OF THE PRODUCT. THE PURCHASER ACKNOLEDGES THAT THEY ALONE HAVE DETERMINED THAT THE PRODUCT WILL SUITABLY MEET THE REQUIREMENTS OF THE PURCHASER’S INTENDED USE. (c) Purchaser Remedy – Hobby World Corporation’s sole obligation hereunder shall be that Hobby World Corporation will, at its option, (i) repair or (ii) replace, any Products determined by Hobby World Corporation to be defective. In the event of a defect, these are the Purchaser’s exclusive remedies. Hobby World Corporation reserves the right to inspect any and all equipment involved in a warranty claim. Repair or replacement decisions are at the sole discretion of Hobby World Corporation. This warranty does not cover damage due to the improper installation, operation, maintenance, or attempted repair by anyone other than Hobby World Corporation. Return of any goods by Purchaser must be approved by Hobby World Corporation before shipment.
Page 3
T700RC GASSER CONVERSION
AMA RULES & REGULATIONS General
1) I will not fly my model aircraft in sanctioned events, air shows or model flying demonstrations until it has been proven to be airworthy by having been previously, successfully flight tested. 2) I will not fly my model higher than approximately 400 feet within 3 miles of an airport without notifying the airport operator. I will give right-of-way and avoid flying in the proximity of full-scale aircraft. Where necessary, an observer shall be utilized to supervise flying to avoid having models fly in the proximity of full-scale aircraft. 3) Where established, I will abide by the safety rules for the flying site I use, and I will not willfully or deliberately fly my models in a careless, reckless and/or dangerous manner. 4) The maximum takeoff weight of a model is 55 pounds, except models flown under Experimental Aircraft rules. 5) I will not fly my model unless it is identified with my name and address or AMA number on or in the model. (This does not apply to models while being flown indoors.) 6) I will not operate models with metal-bladed propellers or with gaseous boosts, in which gases other than air enter their internal combustion engine(s); nor will I operate models with extremely hazardous fuels such as those containing tetranitromethane or hydrazine.
Radio Control 1) I will have completed a successful radio equipment ground range check before the first flight of a new or repaired model. 2) I will not fly my model aircraft in the presence of spectators until I become a qualified flier, unless assisted by an experienced helper. 3) At all flying sites a straight or curved line(s) must be established in front of which all flying takes place with the other side for spectators. Only personnel involved with flying the aircraft are allowed at or in front of the flight line. Intentional flying behind the flight line is prohibited. 4) I will operate my model using only radio control frequencies currently allowed by the Federal Communications Commission. (Only properly licensed Amateurs are authorized to operate equipment on Amateur Band frequencies.) 5) Flying sites separated by three miles or more are considered safe from site-to site interference, even when both sites use the same frequencies. Any circumstances under three miles separation require a frequency management arrangement, which may be either an allocation of specific frequencies for each site or testing to determine that freedom from interference exists. Allocation plans or interference test reports shall be signed by the parties involved and provided to AMA Headquarters. Documents of agreement and reports may exist between (1) Two or more AMA Chartered Clubs, (2) AMA clubs and individual AMA members not associated with AMA Clubs, or (3) two or more individual AMA members. 6) For Combat, distance between combat engagement line and spectator line will be 500 feet per cubic inch of engine displacement. (Example: .40 engine = 200 feet.); electric motors will be based on equivalent combustion engine size. Additional safety requirements will be per the RC Combat section of the current Competition Regulations. 7) At air shows or model flying demonstrations, a single straight line must be established, one side of which is for flying, with the other side for spectators. 8) With the exception of events flown under AMA Competition rules, after launch, except for pilots or helpers being used, no powered model may be flown closer than 25 feet to any person. 9) Under no circumstances may a pilot or other person touch a powered model in flight.
Page 4
T700RC GASSER CONVERSION
CLUTCH ASSEMBLY
Do not open all the bags prior to starting assembly. Open the bags step by step as you go through the instruction manual. The components are bagged to make assembly easier. The parts with a single astericks* are not included. Those components will be needed from your T-Rex 700. If you do not have these or similar parts, this conversion kit will not work. Century part numbers (whenever available) are provided as alternative replacements.
2
1
3 4
6
5
7 CA
8 Clean the top of the pinion gear and the inside surfaces of both the upper and lower bearings inside the clutch shaft bearing block using alcohol. Apply a small amount of Red threadlock to the top edge of the clutch gear where it will contact the bearing. Press the bearing block in place, firmly seating the bearing against the top of the pinion gear.
9 10
This conversion kit uses the regular starting shaft and hex coupler to align the clutch to the clutchbell. Clean both the starting shaft and the inside race of the bearing inside the clutchbell and the inside race of the top starting shaft bearing. Apply a small amount of red threadlock positioned just above where the bottom clutchbell bearing will sit on the starting shaft. Slide the starting shaft up through the bearing blocks. Apply a small amount of medium threadlock to the top of the starting shaft and slide the hex coupler in place aligning the flat spot with one of the holes. Apply medium threadlock to the two M4x4 set screws and tighten in place.
11
CNM4x4SS
12
CNM3x8CS
M3 CNM3LOCK
CNBB511
13
CNBB513
CNBB1019
Page 5
No. 1 2 3 4 5 6 7 8 9 10 11 12 13
Part # HW6002 CNM4X4SS
Description Hex Starter Adapter (六角启动头) M4x4 Set Screw( 无头内六角螺丝)
CNBB513*
5x13x4 Bearing (轴承)
HN7083*
L=60.5mm Hex Mounting Bolt( 六角铝柱)
HN7083* Clutch Bearing Block( 离合器轴承座) CNM3LOCK* M3 Locknut( M3防松螺母) CNM3X8CS* M3x8 Cap Screw( 杯头螺丝) HN6007*
Clutch Nut(离合器齿轮螺母)
CNBB1019* 10x19x5 Bearing (轴承) HW6043B7 16T Clutch Gear(16 齿离合器齿轮) HW6013J CNBB511
Clutch Bell Assembly 69mm( 离合器罩) 5x11x4 Bearing (轴承)
HW6006T7
Start Shaft(启动轴)
Qty 1 2 1 2 2 2 2 1 1 1 1 1 1
T700RC GASSER CONVERSION
BEARING BLOCKS & ELEVATOR ARM
1 2 3 4 5
6
7
8
11
9
10
No. 12x24x6
CNM3x6BHCS
5x8.5 CNM4x4SS
CNBB37F
1 2 3 4 5 6 7 8 9 10 11
Part #
Description
HN7033*
Elevator Ball Link( 升降臂连杆头)
HN7033*
Elevator Arm( 升降控制臂)
CNM2.5X8CS*
M2.5x8 Cap Screw( 杯头螺丝)
CNM3X6BHCS*
M3x6 Button Head Screw ( 圆头螺丝)
CNBB0730F*
3x7x3 Bearing (带边轴承)
CNM4X4SS*
M4x4 Set Screw( 无头内六角螺丝)
HN7033*
Elevator Lever( 升降连动控制臂)
HN7033*
Linkage Ball C(M3x3.5)( 球头C（M3x3.5）)5 x8.5
HN7023A*
Control Shaft( 连动秆)
HN7031*
12x24x6 Bearing (轴承)
HN7031*
Metal Bearing Block( 金属主轴固定座)
CNM2.5x8CS
Page 6
Qty 1 1 1 2 2 1 1 2 1 2 2
T700RC GASSER CONVERSION
FUEL TANK ASSEMBLY
1
2 4
3
5
6
8 7 No. 1 2 3 4 5 6 7 8
Part # HI6139F
Description
HI6138R
Return Tubing(回油管) Nozzle Fitting (出油嘴)
HI6138R
Rubber Stoper/Grommet (油箱塞)
HI6138R HI6139F
Fuel Tank (油箱)
HI6139F
Fuel Pickup Tubing (吸油管)
HI6139F
Fuel Line Tubing (出油管)
HI6138R
Clunk (吸油嘴)
Page 7
Exhaust Tubing (排气管)
Qty 1 2 2 1 1 1 1 1
T700RC GASSER CONVERSION
SIDE FRAMES ASSEMBLY
1
2 3
4
5
13
15
6 14 12
11 10
No. CNBB0510 CNM3x10BHCS CNM3x8BHCS CNM3x6BHCS M3X8 Collar Screw
M3 CNM3LOCK CNM3x18BHCS**
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
Part #
7
9 8
Description
HI6119
Frame Bearing Retainer (侧板轴承座)
CNBB510
5x10x4 Bearing (轴承)
HI6116J
Main Frames (R/L)(左右主体侧板)
H6015B*
M3x8 Button Head Collar Screw (半圆头轴套螺丝) Frame Reinforcement Plate (Left) (左金属机身补强板)
HW6114T7 CNM3X10BH
M3x10 Button Head Screw( 圆头螺丝)
CNM3X6BHCS
M3x6 Button Head Screw( 圆头螺丝)
CNM3X8BHCS
M3x8 Button Head Screw( 圆头螺丝)
HW5004R
Fixed Plate Tank( 油箱固定板)
HW5004R CNM3LOCK
Threaded Spacer( 铝柱)L=16mm M3 Locknut (M3 螺母)
HW5004R
Fixed Fuel Tank Isolators (油箱固定胶圈)
HW6113JA**
Frame Support (铝柱) L=61mm
HW5004R
Threaded Spacer( 铝柱)L=8mm
CNM3X18BHCS*** M3x18 Button Head Screw( 圆头螺丝)
** HW6113T7A may be used as an alternative. *** CNM3X16BHCS (3x16 Button Head Screw) may be used as an alternative.
Page 8
Qty 2 2 2 8 1 3 4 4 2 2 6 4 1 2 2
T700RC GASSER CONVERSION 1 3 2 4
AILERON & TAIL CONTROL LEVER
5 6
7
8 9
17 16 15
14
13 12
10
CA
11
No. Ø3xØ4.8x0.3 Ø3xØ4.4x3 CNBB364 5x9x3 Ø5X8.5 CNM3X8BHCS CNM3X14CS CNM3X12BHCS CNM3X6CS Ø5xØ7.5x3
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17
Part #
Description
HN7078*
Frame Mounting Bolt (铝柱) L=61mm
HN7078*
Ø3xØ5x7.3 Canopy Support( 机头罩支撑柱)
HN7078*
Canopy Spacer( 机头罩支撑垫圈)
CNM3X14CS*
M3x14 Cap Screw (杯头螺丝) Ø5xØ7.5x3 Control Shaft Collar( 连动杆套圈)
HN7023A* HN7034*
5x9x3 Bearing (轴承)
HN7034*
Metal Aileron Lever( 金属左右控制摇臂)
HN7065*
Linkage Ball C(M3x3.5)( 球头C（M3X3.5）)Ø5X8.5
CNM3X6CS*
M3x6 Cap Screw (杯头螺丝) M3x8 Button Head Screw (圆头螺丝)
CNM3X8BHCS* HN6019*
Frame Mounting Block(机身固定块)
HN6038*
Ø3xØ4.4x3 Collar( 尾控制臂铝套)
HN6038*
Tail Control Arm( 尾控制臂) Linkage Ball C(M3x3.5)( 球头C（M3X3.5）)Ø5X8.5
HN7065* CNBB364* HN6038* CNM3X12BHCS*
Page 9
3X6X2.5 Bearing( 轴承) Ø3xØ4.8x0.3 Flat Washer( 平面垫片) M3X12 Button Head Screw( 圆头螺丝)
Qty 1 2 2 2 2 4 2 6 2 2 1 1 1 2 2 2 1
T700RC GASSER CONVERSION
ENGINE ASSEMBLY
1
CNLR1018
CNM5X16CS
2
CNM6X15CS
CNM6.5X13FW
3
CNM3X4SS
4
No. 1 2 3 4 5 6 7 8 9 10 11
5
6
Part #
Description
Qty
CNBB1014A
Clutch One way Bearing (10mm) (单向轴承)
1
HW6011J
Clutch Shoe 59mm ( 离合器)
1
CNM6X15CS M6x15 Cap Screw (杯头内六角螺丝) CNM6.5X13FW 6.5x13x1 Washer (垫片)
1 1
HW6129
Clutch Shoes Adapter/Hub (离合器座)
1
CNM5X16CS
M5x16 Cap Screw (杯头内六角螺丝)
4
HW6128
Engine/Clutch Block (引擎座)
1
HW6192G
Carburetor Arm( 化油器控制臂)
1
CNM3X4SS
M3x4 Set Screw(无头内六角螺丝)
1
CNLR1013A
2mm Short Steel Ball(球头螺丝)
NOT INCLUDED RC Engine(RC 引擎)
1 1
7 8 10
11
Page 10
9 When tightening the M6x16 bolt, you can use a piston locking tool made for gasoline engines or you can remove the spark plug and stuff nylon rope into the piston hole. This will allow you to torque the bolt without the engine spinning. NEVER grab the bottom of the crank shaft where the starter attaches and tighten the bolt holding fan/clutch hub. Once you tighten the M5X16 Flush Head Cap Screws (#6), the Engine/Clutch Block (#7) should be snug and not move. If it can still shift or moves, then install the 8x13x0.5 spacers (HW6182). The reason for this is the chamfer depth found on some Zenoah engines are not consistent with others, therefore some engines will require the spacers and some will not.
T700RC GASSER CONVERSION
ENGINE COOLING
1 2 3
4
10
9
5
6
8
7 CNM4X12CS
No.
CNM3X6BHCS CNM3X8BHCS CNM5X40CS
1 2 3 4 5 6 7 8 9 10
Part #
Description
Qty
CNM4X12CS
M4x12 Cap Screw (杯头内六角螺丝)
CNM3X6BHCS
M3x6 Button Head Cap Screw( 圆头内六角螺丝)
2
HI6020C
Cooling Shroud / Air Deflector (挡风板)
1
HWC2106 /HWC2101
Ignition Disk (点火盘) (OPTIONAL)1
HWC2106/HWC2102
Two Way Cooling Fan (风扇)(OPTIONAL)
HWC2106/CNM3X8BHCS M3x8 Button Head Screw(圆头内六角螺丝)(OPTIONAL)
1
1 6
HWC2106 HWC2106/CNM5X40CS
Pull Start Adapter & Nut (手拉器定位座)(OPTIONAL) M5x40 Cap Screw (杯头内六角螺丝)(OPTIONAL)
1 2
HWC2106/HWC2100
Ignition Pick-Up (点火架)(OPTIONAL)
1
HWC2106/HWC2100
5x9x6 Aluminum Spacers(铝套)(OPTIONAL)
2
5x9x6
Page 11
T700RC GASSER CONVERSION
LANDING FRAME STRUCTURE
1
2 3 4 9
10
5 6 7
11
8 13 12
No. CNM3X8FW
CNM2.5X8CS
CNM4X10CS
5x20
CNM3X4SS CNM3X30CS
1 2 3 4 5 6 7 8 9 10 11 12 13
Part # CNM3X15ST HN7084* HW6117J HW6127D H70059* CNM3X8FW CNM3X30CS HN7049* CNM4X10CS CNM3X4SS* CNM2.5X8CS HW6113T7A
Page 12
Description M3x15 Self Tapping Screws (尖尾自攻螺丝) Front Frame Mount (脚架固定座) Bottom Mount Plate (机身底板) 3x10x17 Landing Gear Pillar (铝柱) Landing Struts (脚架) M3x8x1Flat Washer (平面垫片) M3x30 Cap Screws (杯头螺丝) Landing Skids with Caps (脚架弯管) M4x10 Cap Screws (杯头螺丝) M5x20 Cap Screws (杯头螺丝) M3x4 Set Screw (无头内六角螺丝) M2.5x8 Cap Screw (杯头螺丝) L=61mm Frame Support Bar (带平面铝柱)
Qty 2 2 1 4 2 4 4 2 1 4 4 4 2
T700RC GASSER CONVERSION
FRAME REINFORCEMENT
8 7
1
2 3 4 6
5
Position the engine and spin the clutchbell by hand making sure it spins freely and doesn’t catch on the clutch shoe. If it does, you will need to position the engine within the bottom frame before tightening the screws.
No. CNM2.5x8CS CNM3x8BHCS
CNM3x10BHCS
CNM3x8FW
Part #
Description
Qty
1
HI6116JSA
Frame Reinforcement Plate (Left) (右机身前侧板补强)
1
2
HW6113T7A
L=61mm Frame Support Bar (带平面铝柱)
1
3
HI6118J
Canopy Mount Plate (机头固定板)
1
4
CNM2.5X8CS
M2.5x8 Cap Screw (杯头螺丝)
2
5
HI6116JSB
Frame Reinforcement Plate (Right) (左机身前侧板补强)
1
6
CNM3X10BH
M3x10 Button Head Screw (圆头螺丝)
6
7
CNM3X8FW
M3x8x1Flat Washer (平面垫片)
8
CNM3X8BHCS
M3x8 Button Head Screw (圆头螺丝)
Page 13
6 14
T700RC GASSER CONVERSION
RECEIVER MOUNT
1
2
5
3
4
No. CNM3X10BH
M3x8
1 2 3 4 5
Description
Part #
Qty
HN7050*
L=60.5mm Hex Mounting Bolt (六角铝柱)
4
HN7050*
Receiver Mount ( 接受机座)
HW6113JA**
L=61mm Frame Support (铝柱)
1 1
CNM3X10BHCS
M3x10 Button Head Screw (圆头螺丝)
4
HN6015B*
M3x8 Button Head Collar Screw (半圆头轴套螺丝)
6
*HW6113T7A may be used as an alternative.
Page 14
T700RC GASSER CONVERSION
SKELETAL SUPPORT BRACES
1
3 2 4
10
7
5
8 9 6
CNBB1350
CNM3LOCK
CNM3X14CS
No.
Part #
Description
Qty
1
HN7046*
Tail Boom Mount (Left) (左尾管固定座)
2
HN7046*
L=60.5mm Hex Mounting Bolt (六角铝柱)
6
3
CNBB1350*
5x13x4 Bearing (轴承)
2
4
HN7043*
Front Drive Gear Assembly (尾传动导输出轴组)
1
5
HN7046*
Tail Boom Mount (Right) (右尾管固定座)
1
6
CNM3LOCK*
M3 Locknut (防松螺母)
4
7
HN7043*
Front Umbrella Gear (前轴传伞齿轮)
1
8
CNBB1218*
12x18x4 Bearing (轴承)
2
9
HN7047*
Tail Boom (尾管)
1
CNM3X14CS*
M3x14 Cap Screw (杯头内六角螺丝)
4
10
Page 15
1
T700RC GASSER CONVERSION
TAILBOOM & SUPPORTS
1
6
5 4
2 3
CNM4X10X3
CNM4X10FW
CNM4X16CS
No.
Part #
Description
Qty
1
HN6015B*
M3x8 Button Head Collar Screw (半圆头轴套螺丝)
4
2
CNM4X16CS*
M4x16 Cap Screw (杯头内六角螺丝)
2
3
CNM4X10FW*
M4x10x1 Washer (铝套)
2
4
HN7055A*
Tail Boom Brace (尾管支撑架)
2
5
CNM4X10X3
M4x10x3 Spacer (尾管支撑架)
2
6
HN7078*
L=61mm Frame Mounting Bolt (机身铝柱)
1
M3x8
Page 16
T700RC GASSER CONVERSION
MAIN GEAR ASSEMBLY
1
2 Drop some medium threadlock into the six holes on the main gear case. Then use the M3x8 button head cap screws and install through the main gear case. Make sure to use threadlock sparingly as to not get excess threadlock onto the plastic gear.
3
If in the future your one-way bearing or sleeve is worn or damaged, it is highly recommended to replace the sleeve and one-way bearing hub at the same time.
No.
Part#
Description
4 Qty
1
CNM3X8BHCS M3x8 Button Head Screw (圆头螺丝)
2
HI6057T7
103T Main Gear (103齿齿轮)
1
3
HN7002*
Main Shaft Auto Sleeve (主齿轮铁套)
1
4
HN7002*
One-Way Bearing Cover (单向轴承上盖)
1
5
CNBB1521*
15x21x4 Bearing (轴承)
2
6
HN7002*
One-Way Bearing Collar (单向轴承外环)
1
7
HN7002*
One-Way Bearing (单向轴承)
1
8
HN7002*
One-Way Bearing Mount (单向轴承下盖)
1
9 10
CNM2.5X8CS* M2.5x8 Cap Screw (杯头内六角螺丝) HN7020*
150T Tail Drive Gear (尾驱动齿轮)
5
6
6 7
6 1
8 9
CNM3X8BHCS CNM2.5X8CS
10 CNBB1521
Page 17
T700RC GASSER CONVERSION
MAIN SHAFT TO MAIN GEAR
1
2
3 5
4
CNM3X10BH
No. CNM4X27SCS
CNM4LOCK
Part#
Description
Qty
1
HN7010-1*
Main Shaft (主轴)
1
2
HW6114T7
Frame Reinforcement (右金属机身补强板)
1
3
CNM4LOCK*
M4 Locknut (M4螺母)
1
4
CNM3X10BH
M3x10 Button Head Screw (圆头螺丝)
3
5
CNM4X27SCS*
M4x27 Cap Screw (杯头内六角螺丝)
1
Page 18
T700RC GASSER CONVERSION
SERVO INSTALLATION
1 2
3
14 13
4
12
11
10
No. CNM2NUT
CNM3X6PST
CNM2.3X12ST
CNM2X8PH Ø5 x10
2.6x14
9
8
7
6
Part #
5
Description
Qty
1
HN7074*
Elevator Servo Mount (升降伺服机座)
1
2
NOT INCLUDED
Servo (伺服机)
5
3
HN7074*
M2.6x14 Self Tapping Screw (半圆头内六角自攻螺丝)
4
4
HI6205B
3-Hole Servo Mounting Tabs (伺服机固定板)
4
5
CNM2X8PH
M2x8 Phillips Screw (十字螺丝)
4
6
HI3205A
Servo Mounting Plates (伺服机固定板)
7
CNM2.3X12ST M2.3x12 Self Tapping Screws (尖尾自攻螺丝)
20
8
CNLR1013A
2mm Short Steel Ball (球头)
1
9
NOT INCLUDED
Short Servo Arm( 短伺服机摆臂)
2
10
CNM3X6PST*
M3x6 Self Tapping Screws (尖尾自攻螺丝)
11
NOT INCLUDED
Anti-Vibration Pad (防震胶垫)
12
CNM2NUT*
M2 Nut(M2螺母)
8
13 14
NOT INCLUDED
Long Servo Arm (长伺服机摆臂) Llinkage Ball C(M2x5)( 球头C)Ø5X10
3 8
HN7080*
Page 19
10
5 10
T700RC GASSER CONVERSION
PUSHROD MEASUREMENTS
HELPFUL TOOL:
1 PART# CN2219A: BALL LINK EASY DRIVER
2
3
4
5 HEL PFUL TOOL
6
PART# CN2255: CONTROL ROD SETUP GAUGE
2
33 44 66
3
59 72 92
No.
Part #
1 2 3 4 5 5 6 6
HN7058-1* HN7063* HN7064* HN7064* HN7064* HN7064* CNLR2285 HI6145
Description
Qty
Ball Link(连杆头) L=44mm Linkage Rod( 连杆) L=72mm Linkage Rod( 连杆) L=87mm Linkage Rod( 连杆) L=260mm Linkage Rod( 连杆) L=243mm Carbon Fiber Tube( 碳纤管) L=85mm Linkage Rod( 连杆) Ball Link(连杆头)
4 75 87 108
6
74 87 107
5
243 260 280
Page 20
20 2 2 2 1 1 1 2
T700RC GASSER CONVERSION
MUFFLER INSTALLATION
The muffler is not an included item. It is an optional item that offers better performance but the stock can muffler from the engine can be used.
1 2
4
No. 1 2 3 4
Part # CNM5X25CS CN3071-4 CN3069C CNM3X4SS
Description
Qty
M5x25 Cap Screw (杯头内六角螺丝) (OPTIONAL) M5x8 Lock Washer (弹簧垫片) (OPTIONAL) Torpedo V5 Muffler (排气管) (OPTIONAL) M3x4 Set Screw (无头内六角螺丝) (OPTIONAL)
CNM5X25CS
CNM3X4SS
Page 21
3
1 1 1 1
T700RC GASSER CONVERSION
FUEL LINES AND ESSENTIALS
1 2 No. 1 2 3 4 5 6
Part #
Description
NOT INCLUDED NOT INCLUDED NOT INCLUDED NOT INCLUDED NOT INCLUDED HI6139F
Qty 1 1 1 1 1 3
Receiver(接受机) Gyro (陀螺仪) Anti-vibration Pad (防震垫) Battery(电池) Electronic Starter( 电子启动器) Tubing(油管)
3 4
6
5
T700RC GASSER CONVERSION
CANOPY MOUNTING 2 1
3
4
6 5
No. CNM3X8BHCS CNM3X6PST
1 2 3 4 5 6
Part # CN2210A HI6130GTKNO HI3129C CNM3X6PST CNM3X8BHCS HW3127E
Page 22
Description Canopy Grommet (橡皮环) Fiberglass Canopy (机头) Canopy Mount (机头固定座) M3x6 Phillips Tapping Screws (尖尾螺丝) M3x8 Button Head Screw (圆头螺丝) Canopy Standoffs (机头固定铝柱)
Qty 2 1 1 2 2 2
T700RC GASSER CONVERSION
PULL START ASSEMBLY (OPTIONAL)
1
2
3 4
5 4
Congratulations on finishing the build of the gasser conversion for your T700. Please follow your instruction manual on setting up your transmitter and gyro systems. Also it is very important that you follow the instructions included with the Zenoah engine for the break in process and finally tuning the engine. If the steps are not followed your engine will not perform at it’s optimum levels.
CNM4X10FHCS
CNM4LOCK
CNM4X10CS
No.
Part #
Description
1 2 3 4 5 6
CNM4X10FHCS HWC2103 CN2354 CNM4LOCK CNM4X10CS HWC2103
M4x10 Flush Head Cap Screws (斜头内六角螺丝)(OPTIONAL) Pull Start Mounting Plate (手拉板)(OPTIONAL) Pull Start (手拉器)(OPTIONAL) M4 Locknut (螺母)(OPTIONAL) M4x10 Cap Screw (杯头内六角螺丝)(OPTIONAL) 3x5.8x5.5 Spacers (铝套)(OPTIONAL)
Page 23
Qty 4 1 1 4 4 4
700RC T
GASSER CONVERSION
Hobby World Corporation No.2 Industrial District, Yang Wu, Da Ling Shan, Dong Guan, Guandong, China For support, please contact your local dealer/distributor.
Exclusively Distributed by:
1740-C Junction Ave. San Jose, CA. 95112 U.S.A. www.centuryheli.com
