T3-cv Receiver Manual

Transcript

T3-CV Receiver Manual 1-800-387-4081 Before you begin, read all warnings and installation instructions. Safety & Warnings Securely mount the T3-CV using the two mounting points at each end. This product is intended to be installed and serviced by a qualied licensed electrician. Install in accordance with the National Electric Code, and local regulations. Only power with a regulated (listed) constant voltage Class 2 power supply (12-24V DC). Ensure applicable wire is installed between driver, xture, and any controls in between. When choosing wire, factor in voltage drop, amperage rating and type (in-wall rated, wet location rated, etc.). Inadequate wire installation could overheat wires and cause re. This product is rated for indoor installation and only for dry locations. Do not install in washrooms or areas near water (or the possibility of in the future). Do not modify this product beyond the instructions in this guide or the warranty will be voided. Wiring diagrams in this installation guide for basic installations. Please carefully review your installation before proceeding with a qualied electrician familiar with low voltage wiring techniques. Warning: Input voltage must be identical to output voltage of the LED Fixture! WIRE 6-8MM (0.25-0.30”) Exposed wire should not be more than 6- 8 mm long & solder tip (tinned). Do not allow Wires to cross and insure all exposed wire is fully inserted into the screw terminals. Hand tighten screw terminals. Use 22 to 16 AWG gauge wire for output terminals. T3-CV Operation Overview Remote ID Learning Button MODEL : T3-CV 2.4G WIRELESS REMOTE CONTROL POWER INPUT : DC5V-DC24V OUTPUT : 6A x 3CH Mounting point RGB LED Connection Socket Power Input DC12V~24V Diagram-1 T3-CV Hard Wire Diagram (uses XLD series power supply) L N G O utp u t AC Power 50/60Hz L N In p u t Class 2 Low Voltage Regulated Driver XLD series Power Supply MODEL : T3-CV 2.4G WIRELESS REMOTE CONTROL POWER INPUT : DC5V-DC24V OUTPUT : 6A x 3CH [+] [B] V+ [G] [R] V- T3-CV RGB LED Strip Diagram-2 LED World Inc. | #130 10615 48 ST SE | CALGARY, AB T2C 2B7 | CANADA Copyright @2014 LED WORLD INC™. All Rights Reserved. We are not responsible for errors or omissions. Product and specications subject to change without notice. Registered trademarks are owned by their respective registers, or licensee(s). T3-CV Receiver Manual 1-800-387-4081 T3-CV - 12V Wire Diagram (uses MTR72DAUL-1250B power supply) Class 2 Low Voltage Regulated Driver MTR72DAUL-1250B Power Supply AC Power 50/60Hz MODEL : T3-CV 2.4G WIRELESS REMOTE CONTROL POWER INPUT : DC5V-DC24V OUTPUT : 6A x 3CH [+] [B] [G] [R] MTR72DAUL-1250B T3-CV H05 Connector cable If used with MTR72DAUL-1250B Power Supply RGB LED Strip Diagram-3 T3-CV Technical Specications Input voltage DC5V-DC24V Max current load 6A×3CH Max Class 2 (5A) Max output power 75W/180W (12V/24V) Compatible remote control T1/T2/T2M/T3/T3M/T3X Remote Distance 25m Working temperature -20°C~40°C Dimension L175 × W44 × H30mm Package size L178 × W48 × H33mm Weight (G.W.) 110g 1 LED World Inc. | #130 10615 48 ST SE | CALGARY, AB T2C 2B7 | CANADA Copyright @2014 LED WORLD INC™. All Rights Reserved. We are not responsible for errors or omissions. Product and specications subject to change without notice. Registered trademarks are owned by their respective registers, or licensee(s).