Transcript
CardioActive™ Entertainment Station – Integrated TV Installation and Operation For the T672 Treadmill
Note: iPod is a trademark of Apple Inc., registered in the US and other countries. "Made for iPod" means that an electronic accessory has been designed to connect specifically to iPod and has been certified by the developer to meet Apple performance standards. Apple is not responsible for the operation of this device or its compliance with safety and regulatory standards.
2012.09
TABLE OF CONTENTS CHAPTER 1: CARDIO ACTIVE ENTERTAINMENT STATION (INTEGRATED TV) FOR THE T672 TREADMILL 1.1 INTRODUCTION................................................................................................
1
1.2 LIST OF PARTS.................................................................................................. 2 1.3 INSTALLATION INSTRUCTIONS.......................................................................
3
CHAPTER 2: CARDIO ACTIVE ENTERTAINMENT STATION (INTEGRATED ANALOG TV) OPERATING MANUAL 2.1 TV Operating Instructions................................................................................... 20 2.2 CATV Function Settings...................................................................................... 21 2.3 OSD Menu and Keys in CATV Mode.................................................................. 21 2.4 How to Perform the Search Function.................................................................. 24 2.4.1 Search Function Illustrations - TV System........................................................ 24 2.4.2 NTSC Cable Illustration..................................................................................... 25 2.4.3 TV Scan............................................................................................................. 25 2.4.4 TV Channel Search in Progress........................................................................ 26 2.4.5 iPod Function.................................................................................................... 26 2.5.1 iPod Function Illustrations – iPod System......................................................... 27 2.5.2 iPod Function Illustrations – iPod ON................................................................ 27 2.5.3 iPod Function Illustrations – Source Key........................................................... 28 2.6.1 OSD Menu, Other Functions - Video................................................................ 29 2.6.2 OSD Menu, Other Functions - Audio................................................................. 30 2.6.3 OSD Menu, Other Functions - System.............................................................. 30 2.6.4 OSD Menu, Other Functions - DTV................................................................... 32
CHAPTER 3: CARDIO ACTIVE ENTERTAINMENT STATION – INTEGRATED DIGITAL TV 3.1 Digital TV System Cable Connections................................................................. 34 3.2 Integrated TV Screen Illustration.......................................................................... 34 3.3 DTV（ATSC-USA）Digital TV Functions............................................................. 35
3.4 DTV Mode Operation........................................................................................... 37 3.4.1 DTV Mode......................................................................................................... 37 3.4.2 ATSC Menu....................................................................................................... 37 3.4.3 DTV Mode Key Definitions................................................................................ 37 3.5 Introduction to the ATSC Menu............................................................................ 38 3.6 Auto Search Operation......................................................................................... 38 3.6.1 DTV Menu......................................................................................................... 38 3.6.2 Scan Window.................................................................................................... 39 3.6.3 Channel Search Completed Window................................................................. 39 3.6.4 Channel Scan.................................................................................................... 41 3.7 DVB-T SD (European) Digital TV Functions........................................................ 42 3.8 The System Setup Process.................................................................................. 44 3.8.1 Country Setting................................................................................................. 44 3.8.2 Channel Search................................................................................................ 48 3.8.3 Channel Search Block Diagram......................................................................... 48 3.9 Other Notes.......................................................................................................... 51 3.9.1 DVB-TSD Menu................................................................................................. 51 3.9.2 Program Search................................................................................................ 51 3.9.3 Parental Control................................................................................................ .52 3.9.4 System Settings................................................................................................ 52 3.9.5 Games............................................................................................................... 53 3.9.6 Accessories....................................................................................................... 53 3.9.7 Personal Style................................................................................................... 54 3.10 Setup Menu Navigation...................................................................................... 55 3.11 DVB-TSD Frequency Table and Country List..................................................... 56
CHAPTER 4: DTV DVB-T HD(European High Resolution) Digital TV Functions 4.1 Channel Scan...................................................................................................... 60 4.1.2 Display Function Settings................................................................................. 63 4.1.2 Other Functions................................................................................................ 65 4.1.3 Setup Wizard Troubleshooting......................................................................... 65 4.1.4 Country/Language Setting................................................................................ 66 4.1.5 Main System Screen Troubleshooting.............................................................. 68
CHAPTER 1－CARDIO ACTIVE ENTERTAINMENT STATION (INTEGRATED TV) FOR THE T672 TREADMILL 1.1 INTRODUCTION Congratulations on the purchase of a high quality SportsArt accessory, the CardioActive™ Entertainment Station for the T672 treadmill. The CardioActive™ Entertainment Station is an integrated TV station for use on several SportsArt products. Constructed of high quality materials and designed for years of reliable performance, this accessory was made for full commercial use. Before this product is assembled or operated, we recommend that you familiarize yourself with this manual. Understanding the correct assembly and operation of this product will help ensure that you get optimum results. Please note that SportsArt products use two types of boards for iPod devices. One board only has audio functions. The other board has audio and video functions. Only the audiovideo board is suitable for use with the integrated TV module. Do not use the audio-only board with the integrated TV module. Note: iPod is a trademark of Apple Inc., registered in the US and other countries. "Made for iPod" means that an electronic accessory has been designed to connect specifi cally to iPod and has been certifi ed by the developer to meet Apple performance standards. Apple is not responsible for the operation of this device or its compliance with safety and regulatory standards.
1
1.2 LIST OF PARTS
No.
Qty.
Name
Screwdriver bit and geeen handle 1
2
Specifi cation
Flat and Phillips
Notes
1.3 INSTALLATION INSTRUCTIONS Follow instructions below to assemble this product. Note that in this manual the words “left” and “right” are used to refer to the product and its parts. As such, these designations correspond to the “left” and “right” sides of a person in position to exercise on this product. Also, for brevity, the word “screws” is used where screws, washers, and other hardware may be involved. The illustration below shows the integrated TV screen installed on a T672 treadmill. It shows the end result of this assembly process.
3
STEP 1
Remove Covers
To access the motor compartment, remove covers as explained in steps (a) through (b) below. (a) Remove screws from the power cord connector, and unplug the cord. (b) Remove the motor left and right covers, top and front covers in the order shown below (a), (b), (c),and (d).
(a)
(b) b
a
c a
4
STEP 2
Install the Adapter
Install the adapter and its cord as explained in instructions (a) through (f) below. (a) Use the single hole to secure the set strap onto the inside of the front motor cover as shown. (b) Remove the backing from one side of the double-sided foam tape. Use the tape to secure the adapter box (A4) to the inside of the front cover between the two screw holes. (c) Select a suitable hole in the set strap (A8) and use a screw to secure the adapter (A4) into place. (d) Cut off and dispose the unused part of the set strap (A8).
(a)
(b)
(d)
(c)
5
STEP 2
Install the Adapter (Continued)
(e) Squeeze the sides of the power switch and pull it toward yourself. Disconnect cable connections from the filter and the power switch. Connect cable (A5). Then insert the power switch back into place as shown. (Be careful to ensure that L and N wires are in the correct position.)
(e)
6
STEP 2
Install the Adapter (Continued)
(f) Secure the ground wire from cable (A5) and the ground wire from the pedestal as shown.
(f)
7
STEP 3
Install Cables
Follow instructions (a) through (e) to install cables into the pedestal. (a) First, remove the left bottle holder. (b) Insert the end of the cable (A3) with the plastic cover into the hole under the bottle holder. Feed the cable through the pedestal as shown. At the bottom of the pedestal, remove the plastic cover after pulling the cable through the hole in the pedestal mount. At the top of the pedestal, insert the cable up to the line on the cable.
(a)
(b)
8
STEP 3
Install Cables (Continued)
(c) First, remove the terminal bracket and install the appropriate bracket cover plate (A6). Connect cable (A3a) to the cover plate (A6). Then secure the terminal bracket onto the unit as shown. (d) Connect cable (A3b) to the adapter (A4). (Note: After connecting cable (A3b) to the adapter (A4), push the plastic sheath into place to cover the connectors. To the other end of the adapter (A4) connect cable (A5). (e) Secure left and right side motor covers, the upper cover, and the front cover in order (a)(b)(c)(d). (Note: Before securing the front cover, gather cables into the interior as much as possible.
(c)
(d)
9
STEP 3
Install Cables (Continued)
(e) Secure left and right side motor covers, the upper cover, and the front cover in order (a)(b)(c)(d). (Note: Before securing the front cover, gather cables into the interior as much aspossible.)
(e)
b
c
a c
10
STEP 4
Remove the Cutaway
Remove the cutaway in the display lower cover as follows. (a) Remove screws from the display lower cover. (b) Remove the sticker from the lower cover. Then use wire cutters to remove the cutaway in area A of the lower cover.
11
STEP 5
Remove the Display Upper Cover
Follow instructions (a) through (b) to remove the display upper cover. (a) Open the display upper cover slowly to avoid detaching cables. Disconnect the USB cable. Place the display upper cover flat on the handles. (b) Detach the feeder wire from the left side of the handle. Wrap the feeder wire around the upper part of cable (A3). Then use the feeder wire to pull cable (A3) to the front of the display set plate
(a)
(b)
12
STEP 6
Install the Integrated TV Module
Follow instructions (a) through (e) to install the integrated T module. (a) uide the integrated T module into the hole in the lower cover. (ote While inserting the integrated T module into place feed the cables through the hole in the center of the display lower cover.) (b) Secure screws () first in area A then in area B. After securing the integrated T module carefully cut the ip tie off the cables.
(a)
(b)
A
B
13
STEP 6
Install the Integrated TV Module (Continued)
(c) First, connect cable (L1) to cable (A3). Then detach the coaxial cable splitter (A7) from the metal plate. Connect CATV and DTV cables to the splitter (A7) as shown. Secure the splitter (A7) onto the display set plate. Then secure the ground wire from cable (L2) onto the splitter (A7) as shown.
(c)
14
STEP 6
Install the Integrated TV Module (Continued)
(d) Connect the integrated TV cable (L2) to the decoder board for iPod. (Note: Not every decoder board for iPod supports audio-video functions. With the integrated TV module, only use the audio-video decoder board. If not using iPod functions, do not connect cable L2.) (e) Connect the integrated TV cable (L3) to the display circuit board as shown.
a
(d)
(e)
15
b
STEP 7
Secure the Display Upper Cover
Follow instructions (a) through (c) to secure the display upper cover. (a) Connect the USB cable into place. Organize other cables into place to avoid pinching them. Close the display upper cover. (b) Install the left bottle holder into place. (c) Secure the display upper cover into place.
(a)
(b)
(c)
16
STEP 8
Adjust the TV Screen Angle
To secure the angle of the TV at its recommended position, follow instructions on the sticker (inside the neck cover). To secure the TV screen angle at a different position, follow steps (a) through (d) below. (a) Remove the integrated TV module neck cover. (b) Remove the screws at the lower left and right sides of the bracket. Loosen (but do not remove) screws in position (A) until the angle of the TV screen can be adjusted. (c) After adjusting the angle of the integrated TV screen, secure screws in area (A). While aligning screw holes, secure other screws that were removed in step (b). (d) Fit the integrated TV module neck cover to mesh inside the display top cover in area (B). Then secure the integrated TV module neck cover with its screws.
(a)
(b)
A
(d)
(c)
A
B
17
STEP 9
TV Cable Installation
NTSC system: Directly connect your local TV signal cable to the cable on the unit’s power switch. PAL system: Remove the special connector (A6) from the hardware kit. Connect it to the cable on the unit’s power switch. Then connect your local TV signal cable.
18
CHAPTER 2－ CardioActive™ Entertainment Station – Integrated Analog TV Operating Manual
19
CHAPTER 2－CARDIO ACTIVE ENTERTAINMENT STATION (INTEGRATED ANALOG TV) 2.1 TV Operating Instructions
Power switch
Power LED
1. Press the POWER key to turn on the unit. A green LED on the power switch will light up. (A red LED lights when the unit is not activated.) 2. Wait for the TV screen to light. 3. After turning on, if the screen shows “Video Loss”, there is no input signal. 4. Press the Source key to select your input. TV signal sources include CATV, iPod, and DTV. Among these sources, iPod and DTV are options. 5. Press VOL+/- keys as shown to adjust volume. After you set the volume, the volume window will disappear. 6. Press CH+/- keys as shown to select a channel. 7. The On Screen Display (OSD) menu provides a means to establish settings for brightness, contrast, color saturation, TV scan, and other functions. 20
2.2 CATV Function Settings Connect the analog source cable as shown in Figure (1). Press the source key until 「CATV」 appears in the upper left corner, as shown in Figure (2).
2.3 OSD Menu And Keys in CATV Mode In the CATV mode, after pressing the MENU key, the OSD menu will appear, and key definitions will change. (a) In the main OSD window: ˙The MENU key will become the OK key, used for confirmation. ˙The CH+/- key will become the UP/DOWN key. ˙The VOL- key will become the EXIT key. ＊If no keys are pressed, the OSD screen will disappear. You can also press the Vol- key to exit the OSD menu.
21
(b) In the secondary OSD window: ˙The MENU key will become the OK key, used for confirmation. ˙The CH+/- key will become the UP/DOWN key. ˙The VOL- key will become the EXIT key. ＊If no keys are pressed, the OSD screen will disappear. You can also press the VOL- key to return to the main OSD window.
(c) In the OSD adjustment window: ˙The VOL-/+ key will become the value decrease/increase key. ˙The MENU key will become the OK key. ＊If no keys are pressed for a period of time, or if you are finished making adjustments, press the MENU (OK) key to return to the main OSD window. OSD Main Window
Video Setting Brightness
50
Contrast
50
Saturation
50
Hue
50
Sharpness
50
Image H position Image V position Default
22
OSD Secondary Window
Video Setting
OSD Adjustment Brightness
Example 2
Image H position
Image V position
23
2.4 How to Perform the Search Function 1. Press the MENU key to enter the OSD window. 2. Press the CH- key to select the SYSTEM setting function. 3. Press the OK (MENU) key to enter the system setting mode. 4. Press the CH- key to select the TV system. 5. Press the OK (MENU) key to enter the TV System setting mode. 6. Press the CH+/- key to select NTSC Cable, PAL B/G, or other modes. After making your selection, press the VOL- key to return to the TV System selection. 7. Press the CH- key to choose TV Scan. 8. Press the OK (MENU) key to start the scan function. Scanning can take a long time. Please wait while the scan is being performed.
2.4.1
Search Function Illustrations - TV System SYSTEM SETTING Aspect Ratio
24
2.4.2
NTSC Cable Illustration
SYSTEM SETTING Aspect Ratio
NTSC Cable
2.4.3
TV Scan SYSTEM SETTING Aspect Ratio
25
2.4.4
TV Channel Search in Progress
2.4.5
iPod Function
When you have purchased and installed the iPod option but cannot activate iPod functions via the Source key, please use the following procedure to activate these functions. 1. Press the Source key to select the CATV mode. 2. Press the MENU key to enter the main OSD MENU window. 3. Press the CH- key to select the System Setting function. 4. Press the MENU (OK) key to enter the secondary System Setting window. 5. Press the CH- key to choose the iPod System. 6. Press the MENU (OK) key to enter the iPod System setting function. 7. Press the CH+/- key to select ON, turning on the iPod function. 8. Continually press the VOL- key to exit the OSD MENU.
26
2.5.1
iPod Function Illustrations – iPod System
SYSTEM SETTING Aspect Ratio
2.5.2
iPod Function Illustrations – iPod ON
SYSTEM SETTING Aspect Ratio
Full Screen
Color Temperature
6500k
Channel Display
ON
Language
English
TV System
NTSC Cable
TV Scan
▶
DTV System
Off
iPod System
ON
27
2.5.3
iPod Function Illustrations – Source Key
Connect the iPod. Press the Source key until「iPod」appears in the upper left corner. iPod
Menu
Vol-
Vol+
Ch-
Ch+
Source
Power
Note: When the TV is not on, you can listen to music on the iPod. ˙If you press the VOL+/- key, you can turn on the TV to see the iPod image screen. ˙If you press the TV power switch, the TV will turn on. After the startup screen appears, iPod mode will begin. You can directly use iPod audio/visual functions.
28
2.6.1
OSD Menu, Other Functions - Video
Video setting functions include the following: ˙Brightness adjustment ˙Contrast adjustment ˙Saturation ˙Hue ˙Sharpness ˙Image H position (horizontal picture adjustment) ˙Image V position (vertical picture adjustment) ˙Default (factory setting)
Video Setting Brightness
50
Contrast
50
Saturation
50
Hue
50
Sharpness
50
Image H position ▶ Image V position
▶
Default
▶
29
2.6.2
OSD Menu, Other Functions - Audio
Audio setting functions include the following: ˙Volume ˙Mute
Audio Setting Volume Mute
2.6.3
5 Off
OSD Menu, Other Functions - System
System setting functions include the following: ˙Aspect ratio ˙Color temperature ˙Channel display -- OSD MENU display ˙Language selection ˙TV system selection (NTSC, PAL…) ˙TV scan ˙DTV SYSTEM, digital system selection (ATSC, DVBT, ISDBT, Off), if you purchased this option. ˙iPod System selection (ON, Off), if you purchased this and activated this option via system settings.
30
SYSTEM SETTING Aspect Ratio
Full Screen
Color Temperature
6500k
Channel Display
ON
Language
English
TV System
NTSC Cable
TV Scan
▶
DTV System
Off
iPod System
ON
31
2.6.4
OSD Menu, Other Functions - DTV
When you have purchased and installed the DTV option but cannot activate DTV functions via the Source key, please use the following procedure to activate these functions. 1. Press the Source key to select the CATV mode. 2. Press the MENU key to enter the main OSD menu. 3. Press the CH- key to select the System Setting function. 4. Press the MENU (OK) key to enter the secondary System Setting window. 5. Press the CH- key to select DTV System. 6. Press the MENU (OK) key to enter the DTV System setting function. 7. Press the CH+/- key to select DTV mode (ATSC/DVBT). 8. Continually press the VOL- key to exit the OSD menu. Connect the digital TV signal cable (or wireless antenna) as shown in Figure 3. Press the Source key to select the DTV mode until 「DTV」appears in the left upper corner as shown in Figure 4. For DTV usage, please refer to the digital TV option manual. Antenna
TV
DTV
Menu
Vol-
Vol+
Ch-
Ch+
32
Source
Power
CHAPTER 3－ CardioActive™ Entertainment Station – Integrated Digital TV Operating Manual
33
CHAPTER 3－CARDIO ACTIVE ENTERTAINMENT STATION (INTEGRATED DIGITAL TV) Integrated digital TV is optional and may not be included in your particular model. If your treadmill is equipped with these functions, please note the following.
OPERATING INSTRUCTIONS 3.1 Digital TV System Cable Connections Connect cables for digital TV signal reception as follows. Connect the digital TV cable antenna. Note: Also follow these instructions if, in your area, over-the-air analog and digital signals are simultaneously supported. Antenna
3.2 Integrated TV Screen Illustration
Menu
Vol-
Volume adjustment
Vol+
Ch-
Ch+
Channel selection
Source
Source selection
34
Power
Power Indicator LED switch
3.3 DTV（ATSC-USA）Digital TV Functions Follow instructions below to activate the On Screen Display (OSD) MENU for the DTV system: 1. Press the Source key until DTV appears in the upper left corner of the TV screen. 2. Press the MENU key to enter the OSD window. 3. Press the CH- key to select the SYSTEM setting function. 4. Press the MENU (OK) key to enter the system setting mode. 5. Press the CH- key to select DTV System. 6. Press the MENU (OK) key to enter the DTV System setting mode. 7. Press the CH+/- key to select ATSC mode. After making the selection, press the VOL- key to return to the DTV System selection. Then press the VOL- key again to return to the System Setting. Then press the VOL- key to exit the OSD window. DTV
Menu
Vol-
Vol+
Ch-
Ch+
Source
SYSTEM SETTING Aspect Ratio
Full Screen
Color Temperature
6500k
Channel Display
ON
Language
English
TV System
NTSC Cable
TV Scan
DTV System
Off
iPod System
Off
35
Power
SYSTEM SETTING Aspect Ratio
Full Screen
Color Temperature
6500k
Channel Display
ON
Language
English
TV System
NTSC Cable
TV Scan DTV System
ATSC
iPod System
Off
36
3.4.1
DTV Mode
Press the Source key to select DTV mode.
DTV
Menu
3.4.2
Vol-
Vol+
Ch-
Ch+
Source
Power
ATSC Menu
In the DTV mode, hold the Source key for five seconds to enter the ATSC digital TV system menu. Main Menu Auto Search CH setup CC setup Parental control System setting Version Information
Menu
3.4.3
Vol-
Vol+
Ch-
Ch+
Source
Power
DTV Mode Key Definitions
In DTV mode, key definitions change as follows:
˙The CH+ key will become the UP key. ˙The CH- key will become the DOWN key. ˙The VOL+ key will become the RIGHT key. ˙The VOL- key will become the LEFT key. ˙The Source key will become EXIT key. ˙The MENU key will become the OK key, used for confirmation.
37
3.5 Introduction to the ATSC Menu Auto search includes the following functions: ˙Source Type allows selection of source, either antenna or cable. ˙Start Search begins channel search. ˙Reset resets to factory default settings. ˙SNR (signal to noise ratio).
3.6 Auto Search Operation 3.6.1
DTV Menu
Hold the Source key for five seconds to enter the DTV Menu. From the DTV Menu, select Auto Search. Press the MENU（OK） key to select Source Type from the DTV Menu. Press the MENU（OK） key to select Antenna. Press the CH- key to choose the Start Search function from the DTV Menu. Then press the MENU （OK）key to enter the channel scan function. After channel scan is completed, the channel scan completion message will appear. Please wait for this message to disappear. Then be sure to press the Source（EXIT）key to ensure that keys resume their original functions. The scan function takes some time. Please wait patiently for the scan function to be completed. From menu, select Auto Search
MENU
MENU
CH-
MENU
Press to Press to confirm auto confirm source Go down to is cable/antenna. start search. search.
Auto Search Source type Start Search Reset SNR
Menu
Vol-
Vol+
Press to confirm scan mode activation.
Antenna ▶ 0.00dB
Ch-
Ch+
38
Source
Enter scan mode
Power
3.6.2
Scan Window
Searching Digital channels Source type [Antenna] Searching is in process now Please wait….. To stop press [EXIT] 5% Found 0 Digital channels
Menu
3.6.3
Vol-
Vol+
Ch-
Ch+
Source
Power
Channel Search Completed Window
Channel Search Completed Found ** Digital channels
This screen will automatically disappear.
Menu
Vol-
Vol+
Ch-
Ch+
39
Source
Power
DTV Screen
Menu
Vol-
Vol+
Ch-
Ch+
Source
Power
Note: After the channel scan has been completed, please press the Source key to ensure that keys resume their original functions. During the channel scan process, do not press any keys. Otherwise, the scan process might malfunction. Note: In DTV mode, if the channel scan message appears automatically, hold the Source key for five seconds. (The screen will show no reaction whatsoever.) Release the Source key. Then use VOL+/- to select YES/NO, with YES being confirmation to begin the channel scan function.
Menu
Vol-
Vol+
Ch-
Ch+
40
Source
Power
3.6.4
Channel Scan
After you select the YES key, the channel scan window appears as below.
Searching digital channels Source type [Antenna] Searching is in process now Please wait….. To stop press [EXIT] 5% Found 0 Digital channels
Menu
Vol-
Vol+
Ch-
Ch+
Source
Power
Note: During the channel scan process, please do not press any keys. Otherwise, the scan process might error. Note: In the DTV Menu, if you do not press any keys, within approximately 15 seconds, the screen will revert back to the main DTV screen. When the system reverts to the main DTV screen, press the Source（EXIT）key once to exit the DTV MENU control. Keys will resume their original functions.
41
3.7 DVB-T SD (European) Digital TV Functions Note DTV system OSD menu operation: 1. Press the Source key to directly select DTV from the upper left corner and enter the DTV mode. 2. Press the MENU key to enter the OSD screen. 3. Press the CH1 key to select the SYSTEM SETTING function. 4. Press the OK (MENU) key to enter the DTV System setting mode. 5. Press the CH+/- key to select DVBT mode. After making your selection, press the VOL- key to return to DTV System settings. 6. Then press the VOL- key to return to SYSTEM Settings. Then press the VOL- key to return to the SYSTEM Settings, and press the VOL- key again to exit the OSD screen. DTV
Menu
Vol-
Vol+
Ch-
Ch+
Source
System Setting Aspect
Full Screen
Color Temperature
6500k
Channel Display
ON
Language
English
TV System
NTSC Cable
▶
TV Scan
DTV System
ATSC
iPod System
Off
42
Power
SYSTEM SETTING Aspect
Full Screen
Color Temperature
6500k ON
Channel Display
English
Language
NTSC Cable
TV System TV Scan
DVBT-SD
DTV System
iPod System
Off
In the DTV screen, press and hold the Source key for five seconds until the DVB-T digital TV menu appears.
Main Menu Program List Program Search Parental Control System Setting Accessory Personal Style
Menu
Vo l -
Vol+
Ch-
Ch+
Source
In the DTV Menu, key functions operate as follows: ˙The CH+ key becomes the (Up）key. ˙The CH- key becomes the (DOWN）key. ˙The VOL+ key becomes the (RIGHT）key. ˙The VOL- key becomes the (LEFT）key. ˙The MENU key becomes the confirmation (Ok）key. ˙The Source key becomes the (EXIT）key.
43
Power
Key Functions (remote) ▲CH+ VOL-◀ ● MENU (ok)▶VOL+ ▼CH-
◆ Source(Exit)
3.8 The System Setup Process The system setup includes two steps: establishing the country setting, and establishing the OSD language setting.
3.8.1
Country Setting
The DVB-T SD system has 3 types of frequencies: 6/7/8MHz. Different signals are used in different areas, so during initial setup, country code must be established, before the channel scan process can be performed. Follow instructions below to establish the country setting: 1. Hold the Source key for five seconds until the DTV Menu appears. 2. Select the System Setting. Press the MENU ( OK) key. 3. Select Regional Setting, then press the MENU ( OK) key. 4. The Regional Setting menu appears. At Country, press the VOL+ or VOL- key to select elect your country. Countries include TWN (Taiwan), Vietnam, Deutschland, England, Italia, France, Espana, Nederland, Australia, and China. Note: If your country is not included in the list of countries, please refer to the DVB-T Frequency Table and Country List. For example, the country Poland has an 8 MHz regional setting. Because Poland is not listed, simply choose a country with a similar setting, for instance Holland or Spain. 5. The OSD language will change according to the country selected. Select the appropriate country to aid in DTV Menu operation. After establishing country and OSD language settings, press the MENU (OK) key. Note: OSD languages include English, French, German, Italian, Spanish, Portuguese, and Dutch. 6. After making selections, press the Source (Exit) key to exit the DTV MENU control. Keys resume their original functions. Note: Country and OSD language settings must only be established once. Country Setting Block Diagram Select System Setting from DVBT menu
MENU
CH-
Confirmation
Select Regional Setting
MENU
Press VOL+
MENU
Confirmation to Confirm enter regional Select OSD setting language
44
Source
Exit system
Main Menu Program List Program Search Parental Control
System Setting Accessory Personal Style
Menu
Vol-
Vo l +
Ch-
Ch+
Source
Power
Source
Power
System Setting TV Standard Display Type Video Output Antenna Power
Regional Setting Language Time Setting System Schedule
Menu
Vol-
Vo l +
Ch-
Ch+
45
Regional Setting Country ◀ TWN ▶ OSD Language English Time Zone GMT+8:00
Use VOL+ or VOLto select country.
Menu
Vo l -
Vo l +
Ch-
Ch+
Source
Power
Regional Setting Country TWN OSD Language ◀ English▶ Time Zone GMT+8:00
Use VOL+ or VOLto select OSD language.
Menu
Vo l -
Vo l +
Ch-
Ch+
46
Source
Power
Note: At this point, to establish other DTV system settings, or if you need to redo settings, hold the Source key for five seconds until the DTV Menu appears. Then follow instructions above. Note: If the initial setting wizard appears during a workout, cancel the wizard as follows: 1.Press the Source (Exit) key to leave the DTV MENU control. 2. Please hold the Source key for five seconds until the wizard screen disappears. 3.Press the Source (Exit) key again to leave the DTV MENU control.
47
3.8.2
Channel Search
Follow instructions below to perform a channel scan. 1. Hold the Source key for five seconds to enter the DTV Menu. 2. Select Program Search. Then press the MENU（OK） key to confirm your choice. 3. After entering the Program Search menu, select Automatic Search. 4. The following message appears: Do you want to start Auto Search? Select OK (by first pressing VOL- and pressing MENU). 5. The following message appears: Do you want to erase your previous channel list? Select YES (by first pressing VOL- and pressing MENU). 6. The channel scan window appears. During the channel scan procedure, do not press any key. Otherwise, an error will occur. 7. After channel scan process has been completed, the DTV screen will appear. Press the Source (Exit) key to leave the DTV MENU control. Keys resume their original functions.
3.8.3
Channel Search Block Diagram
Enter Menu, select Program Search
MENU
Enter Program Search menu
MENU
MENU
VOL-
Select Select OK Automatic Search
Confirm
VOL-
Select YES
MENU
Confirm
Main Menu Program List
Program Search Parental Control System Setting Accessory Personal Style
Menu
Vo l -
Vo l +
Ch-
Ch+
48
Source
Power
Start search
Program Search
Automatic Search Manual Search
Menu
Vo l -
Vo l +
Ch-
Ch+
Source
Power
Source
Power
Source
Power
Do you want to start Auto Search? OK
Menu
Vo l -
Vo l +
Cancel
Ch-
Ch+
Do you want to erase your previous channel list? YES
Menu
Vo l -
Vo l +
No
Ch-
Ch+
49
Automatic Search Progress XX% Channel No XX
Menu
TV List: XXX
Music List: XXX
XXX XXX XXX
XXX XXX XXX
Vo l -
Vo l +
Ch-
Ch+
Source
Power
DTV Screen
Menu
Vo l -
Vo l +
Ch-
Ch+
50
Source
Power
3.9 Other Notes 3.9.1
DVB-T SD Menu
The Program List includes the following: 1. TV Program List 2. Music Program List 3. Sort a. By Name b. By Service ID c. By Channel
Program List
TV Program List Music Program List Sort
Menu
3.9.2
Vo l -
Vo l +
Ch-
Ch+
Source
Power
Program Search
Program Search includes the following functions: 1. Automatic Search（This is the recommended channel scan program.） 2. Manual Search
Program Search Automatic Search Manual Search
Menu
Vo l -
Vo l +
Ch-
Ch+
51
Source
Power
3.9.3
Parental Control
˙This program is not activated because it requires a password. ˙Channel Lock ˙Parental Setting (Restricts channels) ˙Change Pin (Change the pin number) Parental Control Channel lock Parental Setting Change Pin
Menu
3.9.4
Vo l -
Vo l +
Ch-
Ch+
Source
Power
System Settings
System settings include the following: ˙TV Standard (Includes PAL, NTSC, and AUTO) ˙Display Type (Includes 4：3 PS, 4：3LB, 16：9) ˙Video Output (CVBS+S-Video) ˙Antenna Power (provides active antenna power supply) ˙Regional Setting ˙Language: OSD selection (Includes English, French, German, Italian, Spanish, Portuguese, Dutch) ˙Time Setting ˙System Schedule (system time)
System Setting TV Standard Display Type Video Output Antenna Power Regional Setting Language: OSD Time Setting System Schedule
Menu
Vo l -
Vo l +
Ch-
Ch+
52
Source
Power
3.9.5
Games
Game selections include the following: ˙Mine ˙Tetris ˙Gomoku ˙Calendar
Game Mine Tetris Gomoku Calendar
Menu
3.9.6
Vo l -
Vo l +
Ch-
Ch+
Source
Power
Ch+
Source
Power
Accessories
Accessories include the following: ˙System Information (version number) ˙Factory Default ˙System Update (software update)
Accessory
System information Factory Default System Update
Menu
Vo l -
Vo l +
Ch-
53
3.9.7
Personal Style
Personal style settings include the following: ˙Menu Color ˙Transparency Level ˙Border Pattern ˙Entry Animation
Personal Style Menu Color ◀ Blue Transparency Level 6 Border Pattern Round Entry Animation Right
Menu
Vo l -
Vo l +
Ch-
Ch+
54
▶
Source
Power
3.10 Setup Menu Navigation Program List TV Program List Music Program List Sort
Sort
▶
Program Search
By Name By Service ID By Channel No.
YES NO
Automatic Search Manual Search
TV Standard PAL
Parental Control
NTSC Channel Lock Parental Setting Change Pin
▶ ▶ ▶ ▶ ▶ ▶ ▶
TV Standard Display Type Video Outpu t Antenna Power Regional Setting Language Time Setting System Schedule
AUTO
Display Type 4:3 PS 4:3 PS 16:9
System Setting
Main Menu Program List Program Search Parental Control System Setting Game Accessory Personal Style
▶
▶ ▶ ▶ ▶
Video Output CVBS+S-Video
Antenna Power OFF ON
Game Mine Tetris Gomoku Calendar
Regional Setting Country ◀ TWN ▶ OSD Language English Time Zone GMT+8:00
Accessory System Information Factory Default System Update
▶ ▶
Personal Style Menu Color ◀ Blue ▶ Transparency Level 6 Border Pattern Round Entry Animation Right
Language OSD Language ◀English▶ 1st Audio Language English 2nd Audio Language English DVB Subtitle English Time Setting GMT Usage ◀ ON ▶ Time Zone GMT+8:00 Factory Default NO YES
55
3.11 DVB-T Frequency Table and Country List Band Switch 6M
Country Argentina Taiwan
VHF 177.0～213.0MHz X
UHF 473.0~803.0MHz
Australia
177.5～ 226.5 MHz 529.5 ～816.5 MHz
7M ＆8M
Deutschland
177.5～ 226.5 MHz 474.0 ～858.0 MHz
8M
Belgium Finland Ireland Netherlands Norway Poland Portugal Russian Singapore Slovenia Spain Sweden Vietnam
!" #$% &'( %)*+ ,-" /0 12
X X X X X X X X X X X X X
474.0～858.0 MHz 474.0～858.0 MHz 474.0～858.0 MHz 474.0～858.0 MHz 474.0～858.0 MHz 474.0～858.0 MHz 474.0～858.0 MHz 474.0～858.0 MHz 474.0～858.0 MHz 474.0～858.0 MHz 474.0～858.0 MHz 474.0～858.0 MHz 474.0～802.0 MHz
8M
Austria China Czech Denmark Estonia France Hungarian Icelandic Italy Latvia Lithuania Switzerland England
34 5 67 89 :+ ; <" => ? @A* BCD /E F
X X X X X X X X X X X X X
474.0～858.0 MHz 474.0～858.0 MHz 474.0～858.0 MHz 474.0～858.0 MHz 474.0～858.0 MHz 474.0～858.0 MHz 474.0～858.0 MHz 474.0～858.0 MHz 474.0～858.0 MHz 474.0～858.0 MHz 474.0～858.0 MHz 474.0～858.0 MHz 474.0～858.0 MHz
7M
PS: Bold characters represent countries included in the DVB-T SD system.
56
CHAPTER 4－ DTV DVB-T HD(European High Resolution) Digital TV Functions Operating Manual
57
CHAPTER 4－DTV DVB-T HD(European High Resolution) Digital TV Functions Instructions for DVB-T HD TV system OSD menu operation follow: 1. Press the Source key to directly select DTV from the upper left corner and enter the DTV mode. 2. Press the MENU key to enter the OSD screen. 3. Press the Ch- key to select the SYSTEM SETTING function. 4. Press the OK (MENU) key to enter the DTV System setting mode. 5. Press the CH+/- key to select DVBT mode. After making your selection, press the VOL- key to return to DTV System settings. 6. Then press the VOL- key to return to SYSTEM Settings, and press the VOL- key again to exit the OSD screen. DTV
Menu
Vo l -
Vo l +
Ch-
Ch+
Source
System Setting Aspect
Full Screen
Color Temperature
6500k
Channel Display
ON
Language
English
TV System
NTSC Cable
▶
TV Scan
DTV System
ATSC
iPod System
Off
58
Power
System Setting Aspect
Full Screen
Color Temperature
6500k
Channel Display
ON
Language
English
TV System
NTSC Cable
TV Scan
▶
DTV System
DVBT -HD
iPod System
Off
While viewing the DTV screen, hold the Source key for five seconds to directly enter the DVBT-HD digital system menu as shown below.
59
In the DTV Menu, key functions operate as follows: ˙The CH+ key becomes the (Up) key. ˙The CH- key becomes the (DOWN) key. ˙The VOL+ key becomes the (RIGHT) key. ˙The VOL- key becomes the (LEFT) key. ˙The MENU key becomes the confirmation (Ok) key. ˙The Source key becomes the (EXIT) key.
Key Functions (remote) ▲CH+ VOL-◀ ● MENU (ok)▶VOL+ ▼CH-
◆ Source(Exit)
4.1 Channel Scan Follow the instructions below to operate the channel scan function. Note: Country/Language setting is done at the factory. The user need not establish the country/language setting. Directly perform the channel scan function. 1. Hold the Source key five seconds to enter the DTV Menu. 2. Press CH+/-(UP/DN) keys to select the Auto Search function. 3. Press the Menu key (ok). At this time, after three seconds, the channel scan screen appears. 4. During channel scan, do not press any other keys. Otherwise, an error will occur. 5. When the channel scan has been completed (DATA SAVING appears on screen), the DTV screen appears. Press the Source (Exit) key to exit the DTV MENU. Key functions revert to their original functions (CH+ and CH- keys control channels; VOL+ and VOL- keys control volume.) Please see the following visual presentation of the channel scan function.
60
61
Auto Search Frequency xxxxKHz
Bandwidth
No.
No.
DVB-T TV
7M
DVB-T Radio
0
Bandwidth shown here will reflect that available in the area of use.
0
Scan progress appears here. After the channel scan is completed, channel information, etc., is stored to memory.
Message
Data Saving....
Note: After the channel scan is completed, the DTV screen appears. Press the Source (Exit) key again to exit the DTV MENU. Key operation will revert to their original functions (CH+ and CH- will control channels; VOL+ and VOL- will control volume.)
62
4.1.2 Display Function Settings Display function settings are explained below.
Channel List Channel Management Auto Search Audio Selection Aspect Ratio Subtitle Teletext
1. Enter the DTV Menu. 2. Press CH+/-(UP/DN) to select the Display Setting function. 3. Press the MENU (OK) key.
Common Interface Conax CA Display Setting
Display Setting Output Resolution
720p PAL
Option 720p PAL
Hue
720p NTSC Saturation
1080i PAL
Contrast
1080i NTSC 1080p PAL
Brightness
1080p NTSC
63
Output resolution setting 1. Press CH+/-(UP/DN) keys to select the Output Resolution function. 2. Press the MENU(OK) key to enter the Option selection. 3. Choose an appropriate resolution. 4. Press the MENU(OK) key to complete your settings.
Hue, saturation, contrast, brightness setting 1. Press CH+/-(UP/DN) keys to select the Hue function. Press VOL+/-(Right/Left) keys to make adjustments. After making adjustments, press the SOURCE key to exit. 2. Setting methods for saturation, contrast, and brightness are the same.
Aspect Ratio Aspect Ratio
Full Screen
Option Full Screen None
1. Press the MENU(OK) key to enter the Option selection. Press CH+/-(UP/DN) to make selections. 2. After making selections, press the MENU(OK) key. 3. Press the Source key to exit the DTV menu.
64
4.1.2 Other Functions Other functions are explained below. (1) Display setting functions appear below. (2) Channel List shows all channels found during the channel scan. (3) Channel Management allows you to ignore, move, or delete channels. (4) Audio Selection allows selection of primary and secondary languages and surround sound. (5) Channel Information offers present channel system parameters and information. (6) Subtitle provides subtitles. (7) Teletext provides access to teletext. (8) Common Interface provides condition assess card menu selection. (9) Conax CA provides conax smart card selection. Note: After the channel scan is completed, the DTV screen appears. Press the Source (Exit) key again to exit the DTV MENU. Keys operation will revert to their original functions (CH+ and CH- will control channels; VOL+ and VOL- will control volume.)
4.1.3 Setup Wizard Troubleshooting The occurrence of the following events will make the Setup Wizard stay on screen after the channel scan function has been completed: (1) if there is a power blackout during the channel scan; (2) if the channel scan begins before an antenna is connected, or if the signal source performs a channel scan during the unit's channel scan. Setup Wizard
Star t Country
Taiwan
OSD Language
English
Summer Time
Off
65
(1) If the channel scan operation is cut short because of a power outage, rectify the situation by carrying out the following instructions. When the power supply is resumed and you turn on the TV, the TV will directly enter DTV mode. The “Setup Wizard”will appear on screen. At this time, hold the Source key for five seconds to enter the DTV Menu. Then use the CH+/- keys to select Auto Search. Finally, press the MENU (OK) key to restart the channel scan. (2) If the antenna has not been installed or the signal source is scanning when the unit scan is started, rectify the situation by carrying out the following instructions. At the end of the channel scan, the “Setup Wizard” screen will appear. At this point, do not press the SOURCE (Exit) key. Just reconnect to the signal source. Use CH+/- keys to select the “START” function. Press the MENU(OK) key to restart the scan function. At this time, if you have already pressed the SOURCE (Exit) key, just reconnect the signal source, hold the Source key for five seconds (to enter the DTV Menu). Use CH+/- keys to select Auto Search. Then press the MENU(OK) key to restart the scan function.
4.1.4 Country/Language Setting Because the Country/Language setting is established at the factory, users generally need not establish this setting. But, if for some reason the language setting must be changed, please follow the instructions below to do so. Disconnect the antenna or signal source. Hold the Source key until the DTV menu screen appears. Start the channel scan function. After the scan function is completed do not press the SOURCE (Exit) key., the “Setup Wizard” screen appears (English is used in this example). Enter settings as shown below. Setup Wizard
Option
Start Country
Taiwan
Australia
OSD Language
English
Austria
Summer Time
Off
Belgium Czech China
1. Press the CH+/-(UP/DN) keys to select Country
2.Press the menu (ok) key to select “Option”. Then press Ch+/- keys to select your country. Press the Menu(ok) key to confirm your choice.
66
Setup Wizard
Option
Start Country
China
Dansk
OSD Language
English
Nederlands
Summer Time
Off
English Eestil Suomi
3. Press CH+/-(UP/DN) keys to select “OSD Language". 4. Press the Menu(ok) key to select language from the options
5. Press the Ch+/- key to select your language. Then press the Menu(ok) key to confirm your selection.
Setup Wizard
6. Select the Start option. Press the Menu(ok) key to begin the scan.
Start Country
Taiwan
OSD Language
English
Summer Time
Off
67
4.1.5 Main System Screen Troubleshooting If, after turning on the TV, the main system screen appears (This screen appears before country/language/scan settings or system reset appear.), follow instructions below to rectify the situation. Main screen
DVB-T TV
1. Press the Source key for five seconds (no prompt will appear).
DVB-T Radio Movie
2. Press the Menu(ok) key to enter “DVBT-TV” mode.
Music Photo System Setting 3. In ”Setup Wizard” select settings such as country, language, scan. The setting method is the same as that for language.
Setup Wizard
Start Country
Germany
OSD Language
English
Summer Time
Off
Note: After the function settings described above have been established, the DTV screen appears, press the Source (Exit) key once to exit the DTV menu. Key operations will return to their original functions (CH+ and CH- keys will control channels; VOL+ and VOL- keys will control volume functions.4 68
