Transcript
Specification Sheet
FTR2 Series
Linear Fluorescent
3/22/2013
Project:
T8 Troffer Reflector Kit
Catalog#:
Delamps up to 4-lamp grid ceiling fixtures to 2-lamps
Approved by:
The FTR2 Troffer Reflector Kit is a simple, cost-effective onepiece reflector used to change fixtures from 2, 3, or 4-lamp to a 2-lamp. This kit uses a reflector, brackets and Tek screws to provide you with recentered lamps without replacing the entire fixture. Additionally, the FTR2 kit offers reduced energy, better lighting efficiency and minimal light loss. Four reflector options include enhanced specular aluminum, specular aluminum, white reflector and white optics.
Reflector
Bracket
Dimensions 2-1/2” 9-3/4”
Front View
20-1/2”
.014” reflector material thickness
Tek Screw Plan View
ORDERING INFORMATION Model Family
Dimensions
Number of Lamps
Reflector Material
Packaging Code
FTR2
4
2
E
KR
FTR2
2 - 2’ x 2’ 4 - 2’ x 4’
Sample Ordering Number: FTR2 4 2 E KR Fluorescent T8 Troffer Reflector Kit 2ft by 4ft dimensions 2 lamps Enhanced Specular Aluminum Reflector Kit with Rapid Start Lampholders
2
N - No Reflector (use with BRKT option) A - Specular Aluminum (86%) E - Enhanced Specular Aluminum (95%) W - White Reflector (91%) O - White Optics (98%)
KR - Kit with Rapid Start Lampholders KI - Kit with Instant Start Lampholders REFL - Reflector only BRKT - Bracket only (use N reflector option)
KR Kit Includes: 2 - Brackets 8 - Tek Screws 4 - Rapid Start Lampholders 1 - Reflector
Specifications subject to change without notice. Howard Lighting Products | 580 Eastview Drive | Laurel, MS 39443 (toll free) 800.956.3456 | (direct) 601.422.0033 | (fax) 601.422.1652 www.HowardLightingProducts.com
KI Kit Includes: 2 - Brackets 8 - Tek Screws 4 - Instant Start Lampholders 1 - Reflector
Specification Sheet
FTR2 Series
Linear Fluorescent
3/22/2013
Project:
T8 Troffer Reflector Kit
Catalog#:
Delamps up to 4-lamp grid ceiling fixtures to 2-lamps
Approved by:
Installation Information
Socket Plate with Lampholders
Reflector
NOTE: 2’x2’ Reflector Assembly Not Shown
NOTE: Do not remove clear protective film from reflector until Step #8. 1. Turn off and lock out electrical power to the lighting fixture during the installation process. 2. Open or remove fixture doorframe (with lens or louver) from lighting fixture to gain access to the interior of the fixture. 3. Remove lamps, ballast covers and lampholder brackets. 4. Disconnect ballast (may not be required) to be removed and remove completely with related wire and lampholders from fixture. Ensure remaining ballast is adequately connected to circuit and unused wires are capped off and secured with UL Listed insulating connectors (wirenuts, electrical tape, etc). 5. Reinstall remaining lampholders into new socket brackets, route wires preventing any pinching or damage to wires leading to the ballast. 6. Center socket brackets on each end of fixture and fasten using TEK screws provided. 7. Remove protective film from reflector and secure reflector in place. 8. Replace lamps. 9. Re-install fixture door with lens or louver. 10. Reapply power to fixture
Specifications subject to change without notice. Howard Lighting Products | 580 Eastview Drive | Laurel, MS 39443 (toll free) 800.956.3456 | (direct) 601.422.0033 | (fax) 601.422.1652 www.HowardLightingProducts.com
