Transcript
----------------- Introduction Table of Content Overview ■ Introduction Overview… … … … … ...… … … … … … … … … … … ....1 Features… … … … … … … .… … … … … … … … … ..… .2 ■ Installations Console Connection… … … … … … .… … … … … … ...3 Computers Connection… … … … … … .… … … .… .… 4 Initial Power-up… … … … … … .… … … … … … ..… … .6 ■ Operations Front Panel operation… … … … ...… … … … ...… ..… .7 Hot-key commands… ...… … … … ...… … … … … ..… .7 ■ Appendices
The KVM Switch SW0202C is a computer switch that allows access to two IBM compatible computers from one keyboard, mouse and monitor. Switching between computers is as easy as pressing the push button or entering hot-key commands from your keyboard. There is no interface card and software to install. The powerful KVM Switch is independent of the computer operating system, allowing the attached computers to run different applications. The space-saving design enables you to connect all the cables to the back of the SW0202C taking the least amount of space on your desk. It is a valuable tool for your computer management.
Specifications… … … … … … ..… … … … … … … … … .9
Automatic Mouse Conversion Please read this manual thoroughly and follow the Installation procedures to prevent any damage to the KVM Switch or any connecting device.
This technology enables you to connect computers with either PS/2 or serial mouse ports to the KVM Switch, and control both computers from one PS/2 mouse. The KVM Switch automatically identifies the mouse and switches to proper mouse protocol.
This device is tested and complies with Part 15 of FCC/class B, CE and VCCI rules.
-
1
-
-----------------Installation
Features nSupports both PS/2 and serial mouse nCascade configuration expands system capability nAuto scan automatically selects computers sequentially nSupports Microsoft IntelliMouse (Pro), IntelliTrackball nHot-key functions allow easy computer access nBuilt-in buzzer for hot-key command confirmation nKeyboard states automatically saved and restored when switching computers nOperating system independent, transparent to all applications nTrue plug and play system configuration nKeyboard and mouse can be hot plugged at any time nHigh VGA resolution 1920x1440 nDDC2B compatible nPower-free operation
Console Connection Turn your computers off. Connect a PS/2 keyboard and a PS/2 mouse to the mini-DIN-6 ports of the C (CONSOLE) marked with K and M respectively. Then connect your VGA monitor cable directly to the HD-DB-15 port of C as shown in figure 1.
Figure 1: CONSOLE Connection
The monitor connected to the HD-DB-15 VGA port of the C must be capable of synchronizing with the computer's video signal. If you are uncertain about the monitor type, please consult the monitor user's manual. The KVM Switch consumes negligible power and is designed to run reliably without external power adapter.
-
2
-
-
3
-
Computers Connection Now you want to connect two computers to the KVM Switch. Use a male-to-male Mini-DIN-6 cable to connect from the first PC’s keyboard port to the corresponding K1 port; and, use another male-to-male Mini-DIN-6 cable from the PC’s mouse port to the M1 port. Then, connect your computer’s VGA port to the HD-DB-15 port of the KVM Switch as shown in figure 2. Follow the same procedures for the second computer using K2 and M2 port.
Figure 3: Adapter and serial mouse connection
NOTE: 1. There is no serial mouse for the C (CONSOLE), just a PS/2 mouse. The KVM Switch's automatic mouse conversion system allows you to connect computers using serial mouse and control the computers from one PS/2 mouse. 2. Be ware that the mouse adapter can only be used on the PC side. Attempting to use it at the C (CONSOLE) side will not work. 3. If your PC uses an AT style keyboard, you will need an AT-to-PS/2 keyboard adapter, DIN-5 male to mini-DIN-6 female, at PC side in order to plug the cable to the SW0202C.
Figure 2: COMPUTER Connection If your computer uses serial mouse, a mouse adapter should be connected to the computer’s mouse port as shown in figure 3. (Note: use only the mouse adapter comes with the kit)
-
4
-
-
5
-
----------------- Operations
Initial Power-up Make sure all computers and KVM Switch are powered down during installation. After connection, you just power up the computers; the KVM Switch will get enough power to operate from the computers. This procedure ensures the KVM Switch receive computer settings correctly when computer boots. Therefore, the KVM Switch generates correct responses and allows both computers to boot successfully without user intervention. Should you decide to expand the system in the future or to replace failed devices, you may hot plug any additional power-downed computer and KVM Switch to the system .
Front Panel operation You may switch to a different computer by pressing the front panel push-button directly or by issuing hot-key commands. The front-panel red indicator changes to reflect the computer port selected. The indicator flashes while in either Auto Scan or Manual Scan mode.
Hot-key commands Hot-key command is a short keyboard sequence to select a computer, to activate computer scan, etc. The KVM Switch interprets keystrokes for hot-keys all the time. A hot-key sequence starts with two left Ctrl keystrokes followed by one or two more keystrokes. A built-in buzzer generates a high-pitch beep for correct hot-key command; otherwise, one low-pitch beep for error and the bad key sequence will not be forwarded to the selected computer. = To select a computer: left Ctrl + left Ctrl + 1 Selects the computer at port 1. left Ctrl + left Ctrl + 2 Selects the computer at port 2 Do not use the keypad at the right of the keyboard. =To start Auto Scan, automatically scan power-
-
6
-
-
7
-
on computers one by one at a fixed interval: left Ctrl + left Ctrl + F 1 To abort the Auto Scan mode, press the left Ctrl key twice. When Auto Scan detects any keyboard or mouse activity, it suspends the scanning till activity stops; it then resumes with the next computer in sequence. The length of the Auto Scan interval (Scan Rate) is adjustable, see below. = Manual Scan enables you to manually switch back and forth between power-on computers. left Ctrl + left Ctrl + F2 Press ↑or ↓to select the previous or the next computer in sequence. And, press any other key to abort the Manual Scan. = To adjust Scan Rate which sets the duration before switching to the next computer in Auto Scan: left Ctrl + left Ctrl + F3 The KVM Switch generates 1 to 4 beeps indicating scan interval of 3, 8, 15 and 30 seconds respectively. = To adjust keyboard typematic rate (characters/sec), this setting over-rides that of BIOS and any operating system: left Ctrl + left Ctrl + F4 The KVM Switch generates 1 to 4 beeps corresponding to 10, 15, 20 and 30 characters/sec respectively.
-
8
-
----------------- Appendices Specifications
SW0202C Computer port number Cascade control PC number Front panel button control Hot plug-and-play Hot-key control Automatic scan interval Year 2000 Compliant Cable Length (Max)
2 Up to 4* 1 Yes Yes 3, 8, 15, 30 seconds Yes 30M(100ft) at CONSOLE 30M(100ft) at PC 1920 x 1440, DDC2B PS/2 PS/2, serial (with adapter) HD-DB-15 male PS/2 PS/2 HD-DB-15 female 420g 40x124x70 1.6x4.9x2.7 Micro Optional (DC 9V,500mA)
VGA Computer keyboard connector mouse monitor Console keyboard connector mouse monitor Weight H x W x D (mm) (in.) size Power supply
* Use three SW0202Cs. If other models (SW0403C, SW0404C, SW0802C, SW0803C, SW0804C, SW1602C, SW1603C) are cascaded, you can control up to 122 computers.
-
9
-
Troubleshooting Ensure that all cables are well seated. Check that keyboard/mouse cables are not swapped. Label and bundle the cables for each computer to avoid confusion when connected to the KVM Switch.
Symptom
Causes
Solutions
Keyboard or Improper power-up Press and hold down the mouse does not sequence. push button for 3 work Keyboard or seconds, the KVM Switch mouse not properly will re-initialize the initialized. keyboard and mouse. If problem persists, unplug the keyboard or mouse, wait for few seconds then plug it back. Keyboard error Loose keyboard on boot connection.
Make sure keyboard cables are well seated.
Keyboard The computer was Press both SHIFT keys. strokes shifted in shifted state when last switched Auto Scan does All PCs are off or not switch PC only one PC is automatically turned on. Scan and KVM mode works for Switch beeps power-on computers only.
-
10
Turn computers on. Press left Ctrl key twice to abort Auto Scan mode.
-
The↑ and ↓ keys do not work in Manual Scan
All PCs are off or only one PC is turned on. Scan mode works for power-on computers only.
The KVM Switch fails to function occasionally.
Computers do not Add a power adapter with supply enough minimum of DC 9V power. 500mA output rating to the SPARE power jack.
Computer can not use serial mouse
Loose mouse adapter
Secure the mouse adapter to computer’s COM port.
Incorrect mouse adapter.
Use only the mouse adapter comes with the SW0202C.
In master/slave configuration, the master unit must have equal or more PC ports than that of slaves. If SW0202C is a slave, its master can be SW0202C, SW0403C, SW0404C, SW0802C, SW0803C, SW0804C, SW1602C, SW1603C
SW0202C can be a slave of SW0202C, SW0403C, SW0404C, SW0802C, SW0803C, SW0804C, SW1602C and SW1603C. If SW0202C is a master, only SW0202C can be its slave.
Not functional in cascade configuration.
-
11
Turn computers on. Press any other key to abort Manual Scan mode.
-
FCC Statement
Other KVM Switches Other high-performance KVM switches
2-port 4-port 8-port 16-port
One-Console KVM Switch No OSD OSD model Rack-mount kit SW0202C SW0403C SW0404C RMK04 SW0802C SW0803C RMK08 SW1602C RMK16
Two-Console KVM Switch OSD model Rack-mount kit 8-port SW0804C RMK08 16-port SW1603C RMK16
-OSD: Advanced On-Screen Display interface enables you to assign PC names, access PCs by the names. Other features include programmable scan pattern, password security, etc.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio technician for help.
Limited Warranty IN NO EVENT SHALL THE DIRECT VENDOR'S LIABILITY FOR DIRECT OR INDIRECT, SPECIAL, INCIDENTIAL OR CONSEQUENTIAL DAMAGES, LOSS OF PROFIT, LOSS OF BUSINESS, OR FINANCIAL LOSS WHICH MAY BE CAUSED BY THE USE OF THE PRODUCT EXCEEDS THE PRICE PAID FOR THE PDOCUDT., The direct vendor makes no warranty or representation, expressed or implied with respect to the contents or use of this documentation, and especially disclaims its quality, performance, merchantability, or fitness for any particular purpose.
-Rack-mount Kit: for industry-standard 19-inch rack cabinet with cable support.
The direct vendor also reserves the right to revise or update the product or documentation without obligation to notify any user of such revisions or updates. For further information, please contact your direct vendor.
-Two-Console KVM switch: provides two access points (local & remote up to 100ft/30M) to manage 8 or 16 computers.
All the brand names and registered trademarks are the property of their respective owners.
-
12
-
-
13
-
PP5-N1200-007 Printed in Taiwan
-
14
-
