Transcript
Table of contents
SAFETy
Safety ......................................................... 2
Maintenance ............................................... 6
Specifications ............................................. 4 Setup .......................................................... 4 Operation.................................................... 5
Parts List and Diagram ............................... 7 Warranty ..................................................... 8
IMpORTANT SAFETy INFORMATION GENERAL pOWER TOOL SAFETy WARNINGS Read all safety warnings and instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury. Save all warnings and instructions for future reference.
SETUp
1. Do not expose to rain or wet conditions. Water entering a tool will increase the risk of electric shock. 2. Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired.
3. Disconnect the adapter from the Light before making any adjustments, changing accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally.
Battery tool use and care
OpERATION
1. Recharge only with the adapters specified by the manufacturer. An adapter that is suitable for one type of tool may create a risk of fire when used with another tool.
2. Under abusive conditions, liquid may be ejected from the battery; avoid contact. If contact accidentally occurs, flush with water. If liquid contacts eyes, additionally seek medical help. Liquid ejected from the battery may cause irritation or burns.
Service Have your tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the tool is maintained.
Spotlight Safety Warnings MAINTENANcE
1. Maintain labels and nameplates on the tool. These carry important safety information. If unreadable or missing, contact Harbor Freight Tools for a replacement. 2. This product is not a toy. Keep it out of reach of children.
4. The warnings, precautions, and instructions discussed in this instruction manual cannot cover all possible conditions and situations that may occur. It must be understood by the operator that common sense and caution are factors which cannot be built into this product, but must be supplied by the operator.
3. WARNING: Handling the cord on this product’s Adapter will expose you to lead, a chemical known to the State of California to cause cancer, and birth defects or other reproductive harm. Wash hands after handling. (California Health & Safety Code § 25249.5, et seq.)
Page 2
For technical questions, please call 1-800-444-3353.
Item 69286
LITHIUM BATTERIES STORE A LARGE AMOUNT OF ENERGy AND WILL VENT FIRE OR EXpLODE IF MISTREATED: 1. Keep Battery pack dry. 2. DO NOT DO ANy y OF THE FOLLOWING TO THE BATTER BATTERy yp pA AcK: a. Open,
b. c. d. e. f.
Drop, Short-circuit, puncture, Incinerate, or Expose to temperatures greater than 140°F.
3. Charge Battery Pack only according to its Adapter’s instructions. 4. Inspect Battery Pack before every use; do not use or charge if damaged.
SAFETy
Lithium Battery Safety Warnings
SAVE THESE INSTRUcTIONS.
TO pREVENT ELEcTRIc SHOcK AND DEATH FROM INcORREcT GROUNDING WIRE cONNEcTION: check with a qualified electrician if you are in doubt as to whether the outlet is properly grounded. Do not modify the power cord plug provided with the Adapter. Do not use the Adapter if the power cord or plug is damaged. If damaged, have it repaired by a service facility before use. If the plug will not fit the outlet, have a proper outlet installed by a qualified electrician.
SETUp
Grounding
Outlets for 2-prong plug
2. Double insulated tools may be used in either of the 120 volt outlets shown in the preceding illustration. (See Outlets for 2-prong plug.)
Extension cords Note: Extension cords must not be used with this item’s Adapter.
OpERATION
1. Tools marked “Double Insulated” do not require grounding. They have a special double insulation system which satisfies OSHA requirements and complies with the applicable standards of Underwriters Laboratories, Inc., the Canadian Standard Association, and the National Electrical Code.
Symbology
Canadian Standards Association Underwriters Laboratories, Inc.
V~ A Item 69286
Volts Alternating Current Amperes WARNING marking concerning Risk of Eye Injury. Wear ANSI-approved safety goggles with side shields.
Read the manual before set-up and/or use. WARNING marking concerning Risk of Fire. WARNING marking concerning Risk of Electric Shock. Properly connect Adapter’s power cord to appropriate outlet. WARNING marking concerning Risk of Explosion. Do not puncture, short, or open battery packs and do not charge damaged battery packs.
For technical questions, please call 1-800-444-3353.
Page 3
MAINTENANcE
Double Insulated
Specifications
SAFETy
Battery Rating
3.7V / 2200mAh
Battery Type
Li-ion
AC/DC Adapter Input Rating
120V~ / 60Hz / 35mA
Cigarette Lighter Adapter Input Rating
12V DC, Fuse: 2A 250V
Light Output
1 Million Candlepower
Setup - Before Use: Read the ENTIRE IMpORTANT SAFETy y INFORMATION section at the beginning of this manual including all text under subheadings therein before set up or use of this product.
SETUp
Note: For additional information regarding the parts listed in the following pages, refer to Parts List and Diagram on page 7.
Functions Adapter Inlet (on back of light)
OpERATION Trigger Lock Switch
MAINTENANcE
Figure A
Page 4
For technical questions, please call 1-800-444-3353.
Item 69286
Operating Instructions Read the ENTIRE IMpORTANT SAFETy y INFORMATION section at the beginning of this manual including all text under subheadings therein before set up or use of this product.
SAFETy
charging Please Note: Spotlight will NOT operate during charging. Adaptor plug lug Inlet
SETUp
pistol Grip charge Light Indicator
charging harging with Ac/Dc A Adaptor:
charging harging with 12V cigarette igarette Lighter Adaptor:
1. Plug AC/DC Adaptor (21) into a 120V outlet.
1. Plug into any 12V DC outlet in an automobile, boat or RV, and then into the Adaptor Plug Inlet located on the back of the Spotlight.
2. Attach the end of the Adaptor cord to the Adaptor Cord Inlet, located on the back of the Spotlight. 3. The Charge Light Indicator will light up. When the Charge Light Indicator goes out, the Spotlight is ready for use. Unplug the Adaptor.
2. The Charge Light Indicator will light up. When the Charge Light Indicator goes out, the Spotlight is ready for use. Unplug the Adaptor. Note: Spotlight will not operate during charging. charging
OpERATION
Figure B
General Operating Instructions 1. Hold the Spotlight using the Pistol Grip. 2. Squeeze the Trigger. If you want the Spotlight to stay on, slide the Lock Switch up while squeezing the Trigger, then release the Trigger and the Spotlight will stay on.
Item 69286
3. When finished using the Spotlight, release the Trigger or push the Lock Switch downward to turn the Spotlight off. Keep Spotlight indoors away from children.
For technical questions, please call 1-800-444-3353.
MAINTENANcE
Using the Rechargeable Spotlight:
Page 5
Maintenance and Servicing procedures not specifically explained in this manual must be performed only by a qualified technician.
SAFETy
TO pREVENT REVENT SERIOUS INJUR INJURy y FROM AccIDENTAL OpERATION: Turn the Trigger of the tool off and unplug the Adapter before performing any inspection, maintenance, or cleaning procedures.
cleaning, Maintenance, and Lubrication 1. BEFORE EAcH USE, inspect the general condition of the tool. Check for: • loose hardware, • cracked or broken parts, and • any other condition that may affect its safe operation.
2. AFTER USE, wipe external surfaces of the Spotlight with clean cloth. 3. Store the Adapter and tool in a dry, indoor area out of reach of children.
SETUp
Replacing the 4V Halogen Bulb:
Ring Lens Reflector
Note: To prevent hand-oil contamination, DO NOT touch the Halogen Bulb with bare hands. Use a lint free, soft, clean rag to handle the Bulb. Note: Unplug all wire connections by holding the connectors and pulling. Do not pull the wires apart by tugging on the wires.
Ring Cover
Bulb
1. Slide the Ring Cover off of the Housing. 2. Unthread the two screws holding the Ring in place. Housing
3. Carefully remove the Ring, the glass Lens and the Reflector.
Spring Clip
Figure c
OpERATION
4. Unplug the black wire (negative) from the bottom of the Reflector. 5. Pull back the casing on the red wire (positive) connection, then unplug the bulb wire from the red wire connection.
Screw
Housing
Black Wire
6. Unhook the ends of the Spring Clip and remove the clip and old Bulb.
Reflector
7. Place the new Bulb into the Reflector Bowl opening and slide the Spring clip under the Tab, over the Bulb Flange, then lock the ends into the “T” Slot. 8. Plug the red and black wires back in place, sliding the casing over the red wire connection. 9. Reassemble the Reflector, Lens, Ring and Ring Cover.
MAINTENANcE
Position Spring Clip Black Wire as shown below Connection
Flange
Tab
Press these ends into “T” Slot
Casing
Red Wire
Figure D
Bulb before locking Spring Clip in place
Bulb Wire Bulb properly installed
“T” slot
Figure E Page 6
For technical questions, please call 1-800-444-3353.
Item 69286
Removing and Recycling the 3.7V Dc D Battery: Note: The Battery for this product is rechargeable and long lasting. When it is worn beyond further use, it should be removed and recycled.
SAFETy
To remove the Battery from the Housing (2), follow these steps: 10. Remove the seven Screws from the Housing. 11. Pull the Housing (2) apart and remove the wires connected to the Battery. 12. Remove the Battery from the Housing (2).
Seven Screws Hold Housing Together Figure G
part
Description
Circuit Board Housing Pistol Grip Holder Pistol Grip Lock Switch Switch Spring Trigger Reflector Lens Ring
Qty 1 1 1 1 1 1 1 1 1 1 1
part 12 13 14 15 16 17 18 19 20 21 22
Description
Ring Cover Screw Halogen Bulb (25W H3 4V) Screw (Housing) Battery Screw Circuit Board Wrist Wrap Auto, Boat, RV, 12V DC Adaptor AC/DC Adaptor (120V) Spring Clip
Qty 1 2 1 7 1 2 1 1 1 1 1
MAINTENANcE
OpERATION
1 2 3 4 5 6 7 8 9 10 11
SETUp
parts List and Diagram
22
Item 69286
For technical questions, please call 1-800-444-3353.
Page 7
Record product’s Serial Number Here: Note: If product has no serial number, record month and year of purchase instead.
Note: Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts.
pLEASE READ THE FOLLOWING cAREFULLy AREFULL AREFULLy THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.
Limited 90 Day Warranty Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase. This warranty does not apply to damage due directly or indirectly, to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activity, improper installation, normal wear and tear, or to lack of maintenance. We shall in no event be liable for death, injuries to persons or property, or for incidental, contingent, special or consequential damages arising from the use of our product. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation of exclusion may not apply to you. THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS. To take advantage of this warranty, the product or part must be returned to us with transportation charges prepaid. Proof of purchase date and an explanation of the complaint must accompany the merchandise. If our inspection verifies the defect, we will either repair or replace the product at our election or we may elect to refund the purchase price if we cannot readily and quickly provide you with a replacement. We will return repaired products at our expense, but if we determine there is no defect, or that the defect resulted from causes not within the scope of our warranty, then you must bear the cost of returning the product. This warranty gives you specific legal rights and you may also have other rights which vary from state to state.
3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • (800) 444-3353
