Table Of Contents: Stor-more® Bulk Storage Locker-welded Wire Mesh Installation Instructions

Transcript

Stor-More® Bulk Storage Locker-Welded Wire Mesh & Stor-More® Tenant Storage Locker Installation Instructions Providing Reliable Engineered Solutions TABLE OF CONTENTS: PAGE 1 PAGE 2 PAGE 3 PAGE 4 PAGE 5 | | | | | COVER, TOOLS REQ’D SPECIFICATIONS PARTS LIST HARDWARE PROVIDED STARTER LOCKER ASSEMBLY INSTRUCTIONS - OPTIONAL SHELF ASSEMBLY PAGE 6 | ADD-ON ASSEMBLY INSTRUCTIONS - OPTIONAL EXPANDED METAL MESH BACK PANEL ASSEMBLY PAGE 7 | OPTIONAL EXPANDED METAL TOP PANEL ASSEMBLY INSTRUCTIONS - WALL MOUNTING INSTRUCTION PAGE 8 | WALL MOUNTING CONTINUED TOOLS REQUIRED: 5/16” [8mm] 3/8” [10mm] MEASURING TAPE LEVEL BATTERY DRILL 7/16” [11mm] OPEN END WRENCH HAMMER HAMMER DRILL WITH Ø 5/16” BIT [8 mm] www.FoldingGuard.com FGI-326 RevB 10/09/2015 ©2015 Folding Guard, A Division of Leggett & Platt Incorporated PAGE 1 of 8 LOCKER TYPE WIDTH ST - STARTER UNIT AD - ADD ON UNIT 3 - 36” DEPTH 4 - 48” DEPTH MESH TYPE: WELDED WIRE ST 133 -FW NO. OF TIERS DEPTH 1 - SINGLE TIER FRONT DOOR 2 - DOUBLE TIER FRONT DOOR 3 - 36” DEPTH 4 - 48” DEPTH 5 - 60” DEPTH FGI-326 RevB 10/09/2015 PART NO. NO. OF TIERS WIDTH ST133-FW 1 36” 36” 90” ST134-FW 1 36” 48” 90” ST135-FW 1 36” 60” 90” ST143-FW 1 48” 36” 90” ST144-FW 1 48” 48” 90” ST145-FW 1 48” 60” 90” ST233-FW 2 36” 36” 90” ST234-FW 2 36” 48” 90” ST235-FW 2 36” 60” 90” ST243-FW 2 48” 36” 90” ST244-FW 2 48” 48” 90” ST245-FW 2 48” 60” 90” AD133-FW 1 36” 36” 90” AD134-FW 1 36” 48” 90” AD135-FW 1 36” 60” 90” AD143-FW 1 48” 36” 90” AD144-FW 1 48” 48” 90” AD145-FW 1 48” 60” 90” AD233-FW 2 36” 36” 90” AD234-FW AD235-FW 2 2 36” 36” 48” 60” 90” 90” AD243-FW 2 48” 36” 90” AD244-FW 2 48” 48” 90” AD245-FW 2 48” 60” 90” ©2015 Folding Guard, A Division of Leggett & Platt Incorporated DEPTH HEIGHT PAGE 2 of 8 PARTS LIST: FRONT: SIDE: WELDED WIRE MESH FRAMED DOOR HARDWARE KIT: WELDED WIRE MESH x1 SINGLE TIER (x1) DOUBLE TIER (x1) STARTER (x2) ADD-ON (x1) OPTIONS: SHELF: (STANDARD ON DOUBLE TIER LOCKERS) BACK: WELDED WIRE MESH TOP: WELDED WIRE MESH 36” WIDE 48” WIDE x3 = 36” DEEP x4 = 48” DEEP x5 = 60” DEEP x1 x1 FGI-326 RevB 10/09/2015 ©2015 Folding Guard, A Division of Leggett & Platt Incorporated PAGE 3 of 8 HARDWARE PROVIDED: STARTER / ADD-ON LOCKER O K AG x1 KT008 N x 12 x 12 x 12 x 12 OPTIONS: EXPANDED METAL MESH BACK WELDED WIRE MESH TOP K AG x 10 x 10 O K AG x1 KT245 x1 KT009 N x 16 x 16 x5 x5 HARDWARE LIST: (K) 1/4”-20 FLANGE NUT (AG) 1/4”-20 x 3/4” SQUARE NECK CARRIAGE BOLT (N) #14-10 x 1 –1/4” SLOTTED HEX HEAD SMS (O) # 14 x 1 TUBULAR PLASTIC ANCHOR FGI-326 RevB 10/09/2015 ©2015 Folding Guard, A Division of Leggett & Platt Incorporated PAGE 4 of 8 1 STARTER 2 X4 AG AG K K X4 INSIDE VIEW INSIDE VIEW NOTE: DO NOT FULLY TIGHTEN ANY NUTS, (FINGER TIGHTEN ONLY) FULLY TIGHTEN AFTER STEP 2 3 4 APPLIES TO MULTI TIER UNITS ONLY INSTALLING SHELVES IN A MULTI TIER UNIT REAR VIEW FINISHED STARTER UNIT FGI-326 RevB 10/09/2015 ©2015 Folding Guard, A Division of Leggett & Platt Incorporated PAGE 5 of 8 5 ADD-ON 6 REMOVE THE STARTER UNIT SIDE PANEL ( RIGHT OR LEFT ) x4 K AG 7 NOTE: BACK PANEL IS OPTIONAL AND NOT SUPPLIED WITH THE STARTER KIT. ATTACH THE ADD-ON ASSEMBLY TO THE STARTER UNIT. REPEAT AS NEEDED. REPLACE THE ORIGINAL SIDE PANEL TO COMPLETE. 8 X8 K AG AG K X8 FGI-326 RevB 10/09/2015 ©2015 Folding Guard, A Division of Leggett & Platt Incorporated PAGE 6 of 8 9 11 FGI-326 RevB 10/09/2015 NOTE: OPTIONAL TOP MOUNTING 10 x10 12 ©2015 Folding Guard, A Division of Leggett & Platt Incorporated PAGE 7 of 8 13 14 x 10 O x10 FGI-326 RevB 10/09/2015 ©2015 Folding Guard, A Division of Leggett & Platt Incorporated PAGE 8 of 8