Transcript
LED light engine / OLED LED compact
Umodule STARK SLE GEN2 CLASSIC STARK SLE
Product description
T
• For spotlights and downlights • High efficiency up to 145 lm/W for the LED module • High system efficiency up to 115 lm/W at tp = 65 °C
U
• High colour consistency (MacAdams 3) angle for spotlights • Excellent thermal management by COB technology • NTC for temperature control for type LES23 and LES26 • Fixing holes for M3 screws • Cooling required
LES 23
7,2
LES 19
• Built-in LED module
Ø50 35 Ø19
• Long life time: up to 80 % luminous flux after 50,000 operating
7,2
O
• Uniform radiation with Dam&Fill technology
LES 26
Ø50 35 Ø23
7,2
• Small LES (light emitting surface) diameter enables small beam
Ø50 35 Ø26
Colour temperatures and tolerances, page 12
ø3,3
Ø3,2
□31
1,75
tc/tp
3,13
□31
tc/tp
ø3,3
Ø26 3,13
Standards, page 5
1,75
tc/tp 22,5
È
□31
LES 26
1,2 ±0,5
1,65 ±0,15
1,75
1,65 ±0,15
IP00
LES 23
22,5
Type of protection
LES 19
1,2 ±0,5
1
Ø23 3,13
65 °C
Risk group (EN 62471:2008)
1,65 ±0,15
tp_rated temperature1
With housing (tc/tp position same as without housing)
22,5
-25 ... +55 °C
1,2 ±0,5
140°
Ambient temperature ta
AS E
Beam characteristic
Ø19 3,13
Technical data
Ø3,2
Ø3,2
• Flexible operating modes
D
hours
3,13
ø3,3
3,13
Without housing Ordering data
PH
Type
Colour Connection Housing Packaging temperature cable
Weight per pc.
STARK SLE G2 LES19 830 CLA
89601652 3,000 K
yes
no
15 pc(s).
0.008 kg
STARK SLE G2 LES19 840 CLA
89601632 4,000 K
yes
no
15 pc(s).
0.008 kg
STARK SLE G2 LES19 750 CLA
89601633 5,000 K
yes
no
15 pc(s).
0.008 kg
STARK SLE G2 LES23 830 CLA
89601634 3,000 K
yes
no
15 pc(s).
0.008 kg
STARK SLE G2 LES23 840 CLA
89601635 4,000 K
yes
no
15 pc(s).
0.008 kg
STARK SLE G2 LES23 750 CLA
89601636 5,000 K
yes
no
15 pc(s).
0.008 kg
STARK SLE G2 LES26 830 CLA
89601637 3,000 K
yes
no
15 pc(s).
0.008 kg
STARK SLE G2 LES26 840 CLA
89601638 4,000 K
yes
no
15 pc(s).
0.008 kg
STARK SLE G2 LES26 750 CLA
89601639 5,000 K
STARK SLE PURE G2 LES19 830 CLA 89601622 3,000 K
yes
no
15 pc(s).
0.008 kg
no
yes
20 pc(s).
0.010 kg
STARK SLE PURE G2 LES19 840 CLA 89601623 4,000 K
no
yes
20 pc(s).
0.010 kg
STARK SLE PURE G2 LES19 750 CLA 89601624 5,000 K
no
yes
20 pc(s).
0.010 kg
STARK SLE PURE G2 LES23 830 CLA 89601625 3,000 K
no
yes
20 pc(s).
0.010 kg
STARK SLE PURE G2 LES23 840 CLA 89601626 4,000 K
no
yes
20 pc(s).
0.010 kg
STARK SLE PURE G2 LES23 750 CLA 89601627 5,000 K
no
yes
20 pc(s).
0.010 kg
STARK SLE PURE G2 LES26 830 CLA 89601628 3,000 K
no
yes
20 pc(s).
0.010 kg
STARK SLE PURE G2 LES26 840 CLA 89601629 4,000 K
no
yes
20 pc(s).
0.010 kg
STARK SLE PURE G2 LES26 750 CLA 89601630 5,000 K
no
yes
20 pc(s).
0.010 kg
Data sheet 06/13-LED100-10 Subject to change without notice.
Article number
www.tridonic.com
1
LED light engine / OLED LED compact
Specific technical data Type7
Photometric Forward Luminous flux Luminous code at flux at current3 4 5 tp = 25 °C2 tp = 65 °C2
Power consumption module8
Forward voltage module6 8
Luminous Luminous Luminous Colour efficacy module efficacy module efficacy system rendering at tp = 25 °C at tp = 65 °C at tp = 65 °C index CRI
Energy classification
STARK SLE LES19 – Operating mode HE at 350 mA STARK SLE G2 LES19 830 CLA
830/349
350 mA
1,450 lm
1,250 lm
11.6 W
33.2 V
125 lm/W
108 lm/W
97 lm/W
80
A+
STARK SLE G2 LES19 840 CLA
840/349
350 mA
1,600 lm
1,400 lm
11.6 W
33.2 V
138 lm/W
121 lm/W
109 lm/W
80
A++
STARK SLE G2 LES19 750 CLA
750/349
350 mA
1,750 lm
1,500 lm
11.6 W
33.2 V
142 lm/W
125 lm/W
113 lm/W
70
A++
STARK SLE LES19 – Operating mode NM at 500 mA STARK SLE G2 LES19 830 CLA
830/349
500 mA
2,000 lm
1,750 lm
17.1 W
34.2 V
117 lm/W
102 lm/W
STARK SLE G2 LES19 840 CLA
840/349
500 mA
2,250 lm
1,900 lm
17.1 W
34.2 V
132 lm/W
112 lm/W
101 lm/W
80
A+
STARK SLE G2 LES19 750 CLA
750/349
500 mA
2,400 lm
2,100 lm
17.1 W
34.2 V
135 lm/W
117 lm/W
105 lm/W
70
A++
80
A+
T
STARK SLE LES19 – Operating mode HO at 700 mA
92 lm/W
830/349
700 mA
2,700 lm
2,300 lm
24.7 W
35.3 V
109 lm/W
93 lm/W
84 lm/W
80
A+
840/349
700 mA
3,000 lm
2,550 lm
24.7 W
35.3 V
121 lm/W
103 lm/W
93 lm/W
80
A+
STARK SLE G2 LES19 750 CLA
750/349
700 mA
3,250 lm
2,800 lm
24.7 W
35.3 V
126 lm/W
107 lm/W
96 lm/W
70
A+
STARK SLE LES23 – Operating mode HE at 500 mA 830/349
500 mA
2,100 lm
1,800 lm
16.5 W
33.1 V
840/349
500 mA
2,300 lm
2,000 lm
16.5 W
33.1 V
STARK SLE G2 LES23 750 CLA
750/349
500 mA
2,500 lm
2,150 lm
16.5 W
33.1 V
127 lm/W
109 lm/W
98 lm/W
80
A+
139 lm/W
121 lm/W
109 lm/W
80
A++
145 lm/W
127 lm/W
115 lm/W
70
A++
O
STARK SLE G2 LES23 830 CLA STARK SLE G2 LES23 840 CLA
U
STARK SLE G2 LES19 830 CLA STARK SLE G2 LES19 840 CLA
STARK SLE LES23 – Operating mode NM at 700 mA STARK SLE G2 LES23 830 CLA
830/349
700 mA
2,850 lm
2,450 lm
23.8 W
33.9 V
120 lm/W
103 lm/W
93 lm/W
80
A+
STARK SLE G2 LES23 840 CLA
840/349
700 mA
3,150 lm
2,700 lm
23.8 W
33.9 V
132 lm/W
113 lm/W
102 lm/W
80
A+
STARK SLE G2 LES23 750 CLA
750/349
700 mA
3,400 lm
2,950 lm
23.8 W
33.9 V
137 lm/W
118 lm/W
106 lm/W
70
A++
STARK SLE LES23 – Operating mode HO at 1,050 mA 830/349
1,050 mA
4,050 lm
3,500 lm
37.1 W
35.3 V
109 lm/W
94 lm/W
85 lm/W
80
A+
840/349
1,050 mA
4,450 lm
3,850 lm
37.1 W
35.3 V
120 lm/W
104 lm/W
93 lm/W
80
A+
STARK SLE G2 LES23 750 CLA
750/349
1,050 mA
4,850 lm
4,200 lm
37.1 W
35.3 V
124 lm/W
108 lm/W
97 lm/W
70
A+
STARK SLE LES26 – Operating mode HE at 700 mA
D
STARK SLE G2 LES23 830 CLA STARK SLE G2 LES23 840 CLA
STARK SLE G2 LES26 830 CLA
830/349
700 mA
2,950 lm
2,500 lm
23.2 W
33.2 V
127 lm/W
108 lm/W
97 lm/W
80
A+
STARK SLE G2 LES26 840 CLA
840/349
700 mA
3,250 lm
2,800 lm
23.2 W
33.2 V
140 lm/W
121 lm/W
109 lm/W
80
A++
STARK SLE G2 LES26 750 CLA
750/349
700 mA
3,500 lm
3,000 lm
23.2 W
33.2 V
144 lm/W
125 lm/W
113 lm/W
70
A++
AS E
STARK SLE LES26 – Operating mode NM at 1,050 mA STARK SLE G2 LES26 830 CLA
830/349
1,050 mA
4,200 lm
3,650 lm
36.0 W
34.3 V
117 lm/W
101 lm/W
91 lm/W
80
A+
STARK SLE G2 LES26 840 CLA
840/349
1,050 mA
4,650 lm
4,000 lm
36.0 W
34.3 V
129 lm/W
111 lm/W
100 lm/W
80
A+
STARK SLE G2 LES26 750 CLA
750/349
1,050 mA
5,050 lm
4,350 lm
36.0 W
34.3 V
133 lm/W
115 lm/W
104 lm/W
70
A++
STARK SLE LES26 – Operating mode HO at 1,400 mA STARK SLE G2 LES26 830 CLA
830/349
1,400 mA
5,400 lm
4,650 lm
49.5 W
35.3 V
109 lm/W
94 lm/W
85 lm/W
80
A+
STARK SLE G2 LES26 840 CLA
840/349
1,400 mA
5,950 lm
5,100 lm
49.5 W
35.3 V
120 lm/W
103 lm/W
93 lm/W
80
A+
STARK SLE G2 LES26 750 CLA
750/349
1,400 mA
6,450 lm
5,550 lm
49.5 W
35.3 V
124 lm/W
107 lm/W
96 lm/W
70
A+
1 If
the max, temperature limits are exceeded, the life of the system will be greatly reduced or the system may be damaged, The temperature of the umodule at the tp-point is to be measured in the thermally stable state with a temperature sensor or or temperature-sensitive sticker as per EN 60598-1, For the precise position of the tp point see the drawing above.
2 Tolerance
range for optical data: ±10 %.
the max, operating current leads to an overload on the umodule, This may in turn result in a significant reduction in lifetime or even destruction of the umodule.
3 Exceeding 4 Max.
permissible surge current: 3 A, duration max. 10 µs. max. 50 % of typ. forward current.
PH
5 Ripple
6 Tolerance
range voltage: ±10 %.
7 HE
... high efficiency, NM ... nominal mode, HO ... high output.
8 All
values at tp = 65 °C.
Data sheet 06/13-LED100-10 Subject to change without notice.
www.tridonic.com
2
LED light engine / OLED LED compact
LED control gear matrix – Umodule STARK SLE G2 REMOTE Type Article no.
IN-BUILT
LCAI 015/0350 A020
LCI 015/0350 E020
LCCI 016/0350 B020
86458899
24166312
86459210
LCI 015/0350 M020
LCI 20W 350mA TEC SR
LCCI 016/0350 Q010
LCI 20W 350mA TEC C
86459179
87500187
86459213
87500079
G
G
G
assignable control gear
Type
Operating mode at 350 mA G
G
G
T
G
STARK SLE G2
REMOTE
Article no.
IN-BUILT
LCI 20W 500mA TEC SR
LCI 20W 500mA TEC C
87500189
87500188
86459107
assignable control gear
Type
Operating mode at 500 mA G
G
D
G
STARK SLE G2
O
Type
LCAI 020/0500 A120 one4all
U
LED control gear matrix – Umodule STARK SLE G2
LED control gear matrix – Umodule STARK SLE G2
REMOTE
Article no..
Type
LCAI 030/0700 A120 one4all
LCI 030/0700 E020
LCI 033/0700 U010
LCI 35W 700mA TEC SR
LCI 030/0700 M120
86458900
24166314
25000669
87500197
86459178
G
G
AS E
Type
LCI 030/0700 A120 86458901
assignable control gear
Operating mode at 700 mA
G
STARK SLE G2
G
G
G
LED control gear matrix – Umodule STARK SLE G2 REMOTE
Type
PH
Article no.
LCAI 050/1050 N020 DALI 24166469*
IN-BUILT
LCI 050/1050 N020
LCI 35W 700mA TEC C
24166468*
87500196
assignable control gear
Type
Operating mode at 700 mA STARK SLE G2
G
G
G
* Configuratet for 700 mA, see control gear data sheet.
Data sheet 06/13-LED100-10 Subject to change without notice.
www.tridonic.com
3
LED light engine / OLED LED compact
LED control gear matrix – Umodule STARK SLE G2 REMOTE Type
IN-BUILT
LCAI 050/1050 N020 DALI
LCI 050/1050 N020
LCI 050/1050 R010
LCI 050/1050 T020
LCI 60W 1050mA TEC SR
LCAI 055/1400 O010 DALI
LCI 055/1400 O010
LCI 60W 1050mA TEC C
24166469
24166468
86459216
86459218
87500203
24166471*
24166470*
87500202
G
G
G
Article no.
assignable control gear
Type
Operating mode at 1,050 mA G
STARK SLE G2
G
G
G
G
U
T
* Configurated for 1,050 mA, see control gear data sheet.
LED control gear matrix – Umodule STARK SLE G2 REMOTE
Article no.
LCI 055/1400 T020
LCI 65W 1400mA TEC SR
LCAI 055/1400 O010 DALI
86459219
87500205
24166471
LCI 055/1400 O010
LCI 055/1400 R010
O
Type
IN-BUILT
24166470
86459217
G
G
assignable control gear
Type
Operating mode at 1,400 mA G
G
G
PH
AS E
D
STARK SLE G2
Data sheet 06/13-LED100-10 Subject to change without notice.
www.tridonic.com
4
LED light engine / OLED LED compact
Standards EN 62031 EN 62471 EN 61547 EN 55015 IEC 62717
Mounting instruction umodule STARK SLE G2 from Tridonic which have to be installed on a heat sink have to be connected with heat-conducting paste or heat conducting adhesive film and fixed with M3 screws. The fixing/cooling surface must be cleaned before installing the u modules to remove all dirt, dust and grease. None of the components of the umodule STARK SLE G2 (substrate, LED, electronic components etc.) may be exposed to tensile or compressive stresses.
Photometric code
Max. torque for fixing: 0.5 Nm.
Key for photometric code, e. g. 830 / 349
For further information please refer to to the brochure entitled “Technical Design-In-Guide SLE GEN2”.
4th digit
6th digit Luminous flux after 25% McAdams after of the lifetime (max.6000h) Code CRI Code Luminous flux Colour temperature in McAdams 25% of the 7 67 – 76 7 ≥ 70 % lifetime Kelvin x 100 initial 8 77 – 86 8 ≥ 80 % (max.6000h) 9 87 – ≥90 9 ≥ 90 %
U
2nd + 3rd digit
5th digit
The device / module contains components that are sensitive to electrostatic discharge and may only be installed in the factory and on site if appropriate EOS/ESD protection measures have been taken. No special measures need be taken for devices/modules with enclosed casings (contact with the pc board not possible), just normal installation practice. Please note the requirements set out in the document EOS / ESD guidelines (Guideline_EOS_ESD.pdf) at: http://www.tridonic.com/com/en/technical-docs.asp
D
Thermal design and heat sink The rated life of u products depends to a large extent on the temperature. If the permissible temperature limits are exceeded, the life of the umodule STARK SLE G2 will be greatly reduced or the umodule STARK SLE G2 may be destroyed.
EOS/ESD safety guidelines
O
1st digit
T
Glow wire test according to EN 62031 with increased temperature of 960 °C passed.
Temperature control for LES23 and LES26 An NTC resistor is on the board of the umodule STARK SLE G2 to control the tp temperature during the operation with a resistor value of 220 kΩ NTC.
Therefore the umodule STARK SLE G2 needs to be mounted onto a heat sink heat sink which does not exceed the value for Rth,max.
240
PH
tp point, ambient temperature and lifetime The temperature at tp reference point is crucial for the light output and life time of a u product. The opeating temperature of a Talex product is crucial for the light output, the product life time but also for the product safety. The thermal limits can be checked at the tp/tc point and at tr. On page 10 the lumen maintenance is shown in relation to the temperature at tp. tp,rated shows the temperature at which the rated values are reached. tc shows the thermal limit for safety reason und must never be exceeded under normal conditions. For the interchangeablity with othe Zhaga products, tr,max is specified directly at the thermal interface to the heatsink of the luminaire. For umodule STARK SLE G2 a tp temperature of 65 °C has to be complied in order to achieve an optimum between heat sink requirements, light output and life time. Compliance with the maximum permissible reference temperature at the tp point must be checked under operating conditions in a thermally stable state. The maximum value must be determined under worst-case conditions for the relevant application.
220 200 180 160
Resistance [kΩ]
AS E
Tridonic’s excellent thermal design for the umodule STARK SLE G2 products provides the lowest thermal resistance and therefore allowing new compact designs without sacrificing quality, safety and life time.
140 120 100 80 60 40 20 0
30
25
35
40
45
60 55 50 Temperature [°C]
65
70
75
80
85
Electrical supply/choice of LED control gear umodule STARK SLE G2 from Tridonic are not protected against overvoltages, overcurrents, overloads or short-circuit currents. Safe and reliable operation can only be guaranteed in conjunction with a LED control gear which complies with the relevant standards. The use of u LED control gears from Tridonic in combination with umodule STARK SLE G2 guarantees the necessary protection for safe and reliable operation. If a LED control gear other than Tridonic uconverter is used, it must provide the following protection: • Short-circuit protection • Overload protection • Overtemperature protection umodule STARK SLE G2 must be supplied by a constant current LED control gear. Operation with a constant voltage LED control gear will lead to an irreversible damage of the module. Wrong polarity can damage the umodule STARK SLE G2.
Data sheet 06/13-LED100-10 Subject to change without notice.
www.tridonic.com
5
LED light engine / OLED LED compact
Umodule STARK SLE G2 LES26 CLASSIC ta tp If 25 °C 65 °C 700 mA 30 °C 65 °C 700 mA 65 °C 700 mA 40 °C 50 °C 65 °C 700 mA 25 °C 65 °C 1050 mA 30 °C 65 °C 1050 mA 40 °C 65 °C 1050 mA 50 °C 65 °C 1050 mA 25 °C 65 °C 1400 mA 30 °C 65 °C 1400 mA 40 °C 65 °C 1400 mA 50 °C 65 °C 1400 mA
Rth, hs-a 2.76 K/W 2.41 K/W 1.70 K/W 1.00 K/W 1.68 K/W 1.46 K/W 1.03 K/W 0.60 K/W 1.16 K/W 1.01 K/W 0.71 K/W 0.40 K/W
U
Rth, hs-a 3.59 K/W 3.13 K/W 2.22 K/W 1.31 K/W 2.41 K/W 2.10 K/W 1.49 K/W 0.87 K/W 1.46 K/W 1.27 K/W 0.89 K/W 0.52 K/W
O
Umodule STARK SLE G2 LES23 CLASSIC ta tp If 25 °C 65 °C 500 mA 30 °C 65 °C 500 mA 40 °C 65 °C 500 mA 50 °C 65 °C 500 mA 25 °C 65 °C 700 mA 30 °C 65 °C 700 mA 40 °C 65 °C 700 mA 50 °C 65 °C 700 mA 25 °C 65 °C 1050 mA 30 °C 65 °C 1050 mA 40 °C 65 °C 1050 mA 50 °C 65 °C 1050 mA
D
Rth, hs-a 5.14 K/W 4.49 K/W 3.19 K/W 1.89 K/W 3.37 K/W 2.94 K/W 2.08 K/W 1.23 K/W 2.23 K/W 1.94 K/W 1.37 K/W 0.80 K/W
PH
AS E
Umodule STARK SLE G2 LES19 CLASSIC ta tp If 25 °C 65 °C 350 mA 30 °C 65 °C 350 mA 40 °C 65 °C 350 mA 50 °C 65 °C 350 mA 25 °C 65 °C 500 mA 30 °C 65 °C 500 mA 40 °C 65 °C 500 mA 50 °C 65 °C 500 mA 25 °C 65 °C 700 mA 30 °C 65 °C 700 mA 40 °C 65 °C 700 mA 50 °C 65 °C 700 mA
T
Heat sink values
Notes The actual cooling can differ because of the material, the structural shape, outside influences and the installation situation. A thermal connection between umodule STARK SLE G2 and heat sink with heat-conducting paste or heat conducting adhesive film is absolutely necessary. Additionally the umodule STARK SLE G2 has to be fixed on the heat sink with M3 screws to optimise the thermal connection. Use of thermal interface material with thermal conductivity of l > 1 W/mK and layer thickness of interface material with max. 50 µm or a similar interface material where the quotient of layer thickness and thermal conductivity b < 50 µmmK/W.
Data sheet 06/13-LED100-10 Subject to change without notice.
www.tridonic.com
6
LED light engine / OLED LED compact
Thermal behaviour storage temperature operating temperature ta tp (at typ. current) tc max. (at typ. current)* max. humidity
Condensation on the module is not allowed. During the processing of the LED modules in the lamp the humidity has to be between 30 and 70%.
-30 ... +80 °C +25 ... +55 °C 65 °C 75 °C 0 ... 80 %
* according to the derating curves
900
800
800
700
700
600
600
500
500
300 200
100
55
60
65
70
75 80 Tc [°C]
85
90
95
100
0
800 700 500 400 300
If [mA]
If [mA]
600
200 100
55
60
65
70
75 80 Tc [°C]
85
90
95
100
PH
50
60
65
70
75 80 Tc [°C]
85
90
95
100
50
55
60
65
70
75 80 Tc [°C]
85
90
95
100
1200 1100 1000 900 800 700 600 500 400 300 200 100 0
50
1200 1100 1000 900 800 700 600 500 400 300 200 100 0
50
Data sheet 06/13-LED100-10 Subject to change without notice.
55
60
65
70
75 80 Tc [°C]
85
90
95
100
Derating curve for Umodule STARK SLE G2 LES23 CLASSIC 5,000 K
If [mA]
Derating curve for Umodule STARK SLE G2 LES23 CLASSIC 4,000 K
If [mA]
55
Derating curve for Umodule STARK SLE G2 LES23 CLASSIC 3,000 K
AS E
900
1200 1100 1000 900 800 700 600 500 400 300 200 100 0
50
D
50
Derating curve for Umodule STARK SLE G2 LES19 CLASSIC 5,000 K
0
300 200
100 0
400
O
400
U
900
T
Derating curve for Umodule STARK SLE G2 LES19 CLASSIC 4,000 K
If [mA]
If [mA]
Derating curve for Umodule STARK SLE G2 LES19 CLASSIC 3,000 K
www.tridonic.com
55
60
65
70
75 80 Tc [°C]
85
90
95
100
7
LED light engine / OLED LED compact
Derating curve for Umodule STARK SLE G2 LES26 CLASSIC 3,000 K
Derating curve for Umodule STARK SLE G2 LES26 CLASSIC 4,000 K
1600
1400
1400
1200
1200
1000
1000
800
800 600
400
400
200
200 50
55
60
65
70
75 80 Tc [°C]
85
90
95
0
100
Derating curve for Umodule STARK SLE G2 LES26 CLASSIC 5,000 K
1600 1400 1200
50
55
60
65
70
75 80 Tc [°C]
85
90
95
100
O
0
T
600
U
If [mA]
If [mA]
1600
D
If [mA]
1000 800 600 400
50
55
60
65
70
75 80 Tc [°C]
85
90
95
100
PH
0
AS E
200
Data sheet 06/13-LED100-10 Subject to change without notice.
www.tridonic.com
8
LED light engine / OLED LED compact
Lumen maintenance for HE operation operating time in h
80 70 50 80 70 50 80 70 50 80 70 50
> 50,000 > 50,000 > 50,000 > 50,000 > 50,000 > 50,000 50,000 > 50,000 > 50,000 42,000 > 50,000 > 50,000
25
55
65
75
T
luminous flux in %
U
tp temperature in °C
luminous flux in %
operating time in h
80 70 50 80 70 50 80 70 50 80 70 50
> 50,000 > 50,000 > 50,000 43,000 > 50,000 > 50,000 37,000 > 50,000 > 50,000 31,000 50,000 > 50,000
25
55
65
AS E
75
D
tp temperature in °C
O
Lumen maintenance for HO operation
Luminous flux and operating current for LES19 at tp = 65 °C 3000 2500
lm
2000 1500
PH
1000
3000 K 4000 K 5000 K
500
0
0
100
200
300
400 mA
500
600
700
Data sheet 06/13-LED100-10 Subject to change without notice.
www.tridonic.com
800
9
LED light engine / OLED LED compact
Luminous flux and operating current for LES23 at tp = 65 °C 4500 3000 K
4000
4000 K
3500
5000 K 3000
T
lm
2500 2000 1500
U
1000 500 0 200
400
600 mA
800
1000
Luminous flux and operating current for LES26 at tp = 65 °C
D
6000 5000
3000 2000 1000 0
AS E
4000
lm
1200
O
0
0
200
400
600
800 mA
1000
1200
1400
3000 K 4000 K 5000 K
1600
PH
Relative forward voltage and relative luminous flux 1.05
1.14 1.12 1.1
1.03
rel. luminous flux [a.u.]
relative voltage [a.u.]
1.04
1.02
1.01 1
0.99
1.06 1.04 1.02 1 0.98 0.96
0.98 0.97 20
1.08
0.94 30
40
50 tp [°C]
60
70
75
0.92 20
30
40
50 tp [°C]
60
70
75
The diagrams based on statistic values. The real values can be different.
Data sheet 06/13-LED100-10 Subject to change without notice.
www.tridonic.com
10
LED light engine / OLED LED compact
Wiring with housing
Wiring without housing NTC solder pads
+
+ red AWG 24 - black
Removing wires by lightly pressing on the push button.
D
wire preparation:
U
Wiring type and cross section The wiring has to be solid cable with a cross section of 0.5 to 0.75 mm² or with flexible cable with soldered ends with a cross section of 0.5 mm². For the push-wire connection you have to strip the insulation (5 – 6 mm).
600 mm
O
8
T
NTC (if existing)
–
5 – 6 mm
Optical characteristics Umodule STARK SLE G2
AS E
The optical design of the umodule STARK SLE G2 product line ensures optimum homogenity for the light distribution. Light distribution 100
60 40 20
-10° 0° 10°
20°
30°
40°
-50°
50°
-60°
60°
70°
PH
relative inetnsity [%]
80
-30° -40°
-20°
-90° 100 80
60
40
20
80°
0
20
40
60
80 100
90°
Data sheet 06/13-LED100-10 Subject to change without notice.
www.tridonic.com
11
LED light engine / OLED LED compact
Coordinates and tolerances according to CIE 1931 The specified colour coordinates are measured integral by a current impulse with nominal values of module after a settling time of 100 ms. The ambient temperature of the measurement is ta = 25 °C. The measurement tolerance of the colour coordinates are ± 0.01. 3,000 K y0 0,4041
0,4250
0,04
0,4200
0,035
0,4050 0,4000 0,3950 0,3900
4,000 K x0 0,3804
y0 0,3767
norm. intensity [W/nm]
0,4000
0,3950
0,3900
0,3850
PH
0,3600
0,3550
0,3800
0,3600
0,3750
0,3650
0,3700
0,3700
0,3650
0,3750
0,015 0,01
0 380
AS E
Centre
0,3800
0,02
460
500
540 580 620 660 wave length [nm]
700
740
780
420
460
500
540 580 620 660 wave length [nm]
700
740
780
0,04 0,035 0,03 0,025 0,02 0,015 0,01 0,005 0 380
MacAdam ellipse: 3SDCM
Data sheet 06/13-LED100-10 Subject to change without notice.
420
D
0,4600
0,4550
0,4500
0,4450
0,4400
0,4350
0,4300
0,4250
0,4200
MacAdam ellipse: 3SDCM
0,3850
0,025
0,005
0,3850
0,3900
0,03
U
0,4100
O
norm. intensity [W/nm]
0,4150
0,3950
T
x0 0,4369
Centre
www.tridonic.com
12
LED light engine / OLED LED compact
5,000 K x0 0,3451
Centre
y0 0,3516
0,06
0,3600 0,3550 0,3500 0,3450 0,3400 0,3350
0,3650
0,3600
0,3550
0,3500
0,3450
0,3400
0,3350
0,3300
0,04 0,03 0,02 0,01 0 380
0,3300 0,3250
0,05
T
norm. intensity [W/nm]
0,3650
U
0,3700
420
500
540 580 620 660 wave length [nm]
700
740
780
PH
AS E
D
O
MacAdam ellipse: 3SDCM
460
Data sheet 06/13-LED100-10 Subject to change without notice.
www.tridonic.com
13
