Transcript
TAMLITE EMERGENCY BAY 3 II UNIT 48 B II PIPERS ROAD PARK FARM INDUSTRIAL ESTATE II REDDITCH WORCESTERSHIRE II B98 0HU T 01527 510 253 F 01526 510 592 E
[email protected] W WWW.FIRESCAN.CO.UK
FIRE ALARM TECHNICAL T 01527 510 598 F 01527 510 592 E
[email protected] Firescan 0056
CONVENTIONAL II 2 WIRE II ADDRESSABLE II SPECIALIST II ANCILLARIES
WELCOME TAMLITE EMERGENCY AND FIRE HAS BEEN ESTABLISHED FOR OVER 25 YEARS AS A SUPPLIER OF FIRE ALARM PRODUCTS. COMPLEMENTED WITH AN INFRASTRUCTURE OF INDUSTRY PROFESSIONALS FOR SALES, MARKETING AND TECHNICAL SUPPORT. WE CAN OFFER SYSTEM SOLUTIONS FOR ALL TYPES OF PREMISES INCLUDING MULTIPLE-OCCUPANCY, LOCAL AUTHORITY, INDUSTRIAL OR COMMERCIAL PROPERTIES.
CONTENTS CONVENTIONAL
3-20
2 WIRE
21-24
ADDRESSABLE
25-37
SPECIALIST EQUIPMENT
38-40
ANCILLARY EQUIPMENT
41-44
TECHNICAL
44-48
THE FIRESCAN SPECIFIERS GUIDE DETAILS PRODUCTS TO MEET ALMOST ANY SYSTEM REQUIREMENT. THIS IS OFFERED IN CONJUNCTION WITH A CRUCIAL DESIGN AND TECHNICAL SUPPORT SERVICE TO ENSURE FULLY COMPLIANT SYSTEMS, AS WELL AS TROUBLE FREE INSTALLATION, COMMISSIONING AND HAND OVER. TO COMPLEMENT THIS SERVICE WE ARE ABLE TO OFFER ON-SITE SURVEYS, DESIGN, AND COMMISSIONING.
1
2
INFINITY FEATURES - LPCB and EN54 part 2 and 4 approved - BS5839 part 4 compliant - Microprocessor control - 2-8 Zones - Fire and fault contacts - Can be semi-flush mounted - One-man test - Earth fault monitoring - Zone isolate - Capacity for 2 x 3.4 Ah batteries - Sounder delay option - Coded access via keypad - Sounder circuits 3 and 4 can be
configured as auxiliary 24V supplies
3
-
Operating voltage ~ 230V AC @ 50/60Hz
-
System voltage ~ 24V DC nominal
-
Charger voltage ~ 27.6V DC nominal
-
Fire triggering resistance ~ 470Ω/680Ω
-
Detection zone EOL ~ IN4002 diode
A
B
C
-
Sounder circuit EOL ~ 10KΩ Resistor
375
316
90
-
Auxiliary fire relay ~
1A @ 30V DC Max (volt free)
-
Auxiliary fault relay ~
1A @ 30V DC Max (volt free)
-
ABS flame retardant
-
Coloured white
DIMENSIONS (mm)
A
B
INFINITY Order Codes
FSINF-2
FSINF-4
FSINF-6
FSINF-8
No. of detection circuits
2
4
6
8
No. of sounder circuits
4
4
4
4
Zone capacity
40mA
40mA
40mA
40mA
Sounder circuit current
250mA per circuit
250mA per circuit
250mA per circuit
250mA per circuit
Supplied c/w batteries
2 x 3.4Ah 12V
2 x 3.4Ah 12V
2 x 3.4Ah 12V
2 x 3.4Ah 12V
Wgt (Kg) incl. batteries
5.6
5.6
5.6
5.6
C
CONVENTIONAL
CONVENTIONAL
SPECIFICATION
4
OPTIMA FEATURES - EN54 part 2 approved - BS5839 part 4 compliant - Microprocessor control - 2-8 Zones - Fire contacts - Can be semi-flush mounted - Auxiliary 24V power supply - One-man test - Earth fault monitoring - Zone isolate - Modern design - Capacity for 2 x 7.2 Ah batteries - Sounder delay option - Four sounder circuits - Keyswitch and coded access - Removable grommets on top of enclosure
5
-
Operating voltage ~ 230V AC @ 50/60Hz
-
System voltage ~ 24V DC nominal
-
Charger voltage ~ 28.4V DC nominal
-
Fire triggering resistance ~ 470Ω/680Ω
-
Detection zone EOL ~ 100µF capacitor 25 - 100V
-
Sounder circuit EOL ~ 10KΩ Resistor
-
Auxiliary fire relay ~ 1A @ 30V DC Max (Volt Free)
-
Auxiliary supply ~ 24V DC 200mA
-
ABS flame retardant
-
Coloured black
DIMENSIONS (mm) A
B
C
355
275
100
A
B
OPTIMA Order codes
FSOPT-2
FSOPT-4
FSOPT-6
FSOPT-8
No. of detection circuits
2
4
6
8
No. of sounder circuits
4
4
4
4
Detection zone capacity
30mA
30mA
30mA
30mA
Sounder circuit current
150mA per circuit
150mA per circuit
150mA per circuit
150mA per circuit
Supplied c/w batteries
2 x 3.4Ah 12V
2 x 3.4Ah 12V
2 x 7.2Ah 12V
2 x 7.2Ah 12V
Wgt (kg) incl. batteries
5.60
5.60
8.55
8.55
* Configuration of 6 zone panel
C
CONVENTIONAL
CONVENTIONAL
SPECIFICATION
6
VISTA
VISTA
FEATURES
FEATURES
-
LPCB approved
-
LPCB approved
-
Remote indicator output
-
Remote indicator output
-
Modern attractive design
-
Modern attractive design
-
Central LED providing 360° visibility
-
Central LED providing 360° visibility
-
Available in a range of coloured
-
Available in a range of coloured
decorative finishes
decorative finishes
-
Symmetrical chamber
-
Symmetrical chamber
-
Patented double dust trap
-
Patented double dust trap
-
Easy to install
-
Easy to install
SMOKE DETECTORS
HEAT DETECTORS
SPECIFICATION
SPECIFICATION
-
Operating voltage ~ 10 - 30V DC
-
Operating voltage ~ 10 - 30V DC
-
Quiescent Current (typical) ~ 90µA
-
Quiescent Current (typical) ~ 90µA
-
Maximum Current ~ 40mA
-
Maximum Current ~ 40mA
-
Remote Indicator Drive ~ 20mA (max)
-
Remote Indicator Drive ~ 20mA (max)
-
Operating temperature ~ -30°C to + 70°C
-
Operating temperature ~
-
Base fixing centres ~ 46 - 72mm
-10°C to + 50°C
-
Constructed from modified polycarbonate
-
Base fixing centres ~ 46 - 72mm
-
Coloured white
-
Constructed from modified
-
Coloured decorative finishes
Coloured decorative finishes
polycarbonate
IP42
7
VISTA HEAT DETECTOR
Order Code
Description
Wgt (Kg)
FSV-OPT
Photoelectric smoke detector
0.09
Dimensions (mm) Dia
C
110
54
DETECTOR BASES
Dia
IP42
Order Code
Description
Wgt (Kg)
FSV-FH78
Fixed Heat Detector
FSV-RR58
Dimensions (mm) Dia
C
0.09
110
54
Rate of Rise detector
0.09
110
54
Order Code
Description
Wgt (Kg)
DETECTOR BASES
Order Code
Description
Wgt (Kg)
FSV-CDB
Common Diode Base
FSV-DDB FSV-RDB
C
Coloured white
-
Dia
Dimensions (mm) Dia
C
0.04
110
16
FSV-CDB
Common Diode Base
Deep detector base
0.05
110
25
FSV-DDB
Relay detector base
0.10
110
30
FSV-RDB
C
Dia
-
EOL
C
Dia
Dimensions (mm) Dia
C
0.04
110
16
Deep detector base
0.05
110
25
Relay detector base
0.10
110
30
C
-
+
+
Control panel
Control panel
EOL
CONVENTIONAL
CONVENTIONAL
VISTA SMOKE DETECTOR
-
8
HOCHIKI
HOCHIKI
FEATURES
FEATURES
-
LPCB and VdS approved
-
LPCB and VdS approved
-
Remote indicator output
-
Remote indicator output
-
Wide voltage range
-
Wide voltage range
-
Low profile modern design
-
Low profile modern design
-
Twin fire LEDs allow 360° viewing
-
Twin fire LEDs allow 360° viewing
-
Range of mounting bases
-
Range of mounting bases
-
Also available in black or white
-
Electronic linear heat detection
SMOKE DETECTORS
HEAT DETECTORS
SPECIFICATION
SPECIFICATION
OPTIONS
-
Operating voltage ~ 9.5 - 30V DC
-
BK Black versions for special order (FSOS2 only)
-
Quiescent current (typical) ~35µA
-
W
-
Maximum current ~ 40mA
-
Remote Indicator drive ~ 20mA (max)
- IS
-
Operating temperature ~ -10°C to + 50°C
-
Base fixing centres ~ 48 - 74mm
-
ABS flame retardant
-
Coloured ivory
-
IP42
White versions for special order Intrinsically safe for special order (coloured ivory only)
HOCHIKI HEAT DETECTOR
HOCHIKI SMOKE DETECTOR Description
Dia
C
FSOS2
Photoelectric smoke detector
0.10
100
43
FSIRFD
Infrared flame detector
0.12
100
43
60ºC fixed heat detector
FSFH90
C
0.08
100
43
90ºC fixed heat detector
0.08
100
43
FSRR60
60ºC rate of rise and fixed heat detector
0.08
100
43
FSRR90
90ºC rate of rise and fixed heat detector
0.08
100
43
Quiescent current (typical) ~35µA
-
Maximum current ~ 40mA
-
Remote Indicator drive ~ 20mA (max)
-
Operating temperature ~
-10°C to + 50°C
-
Base fixing centres ~ 48 - 74mm
-
ABS flame retardant
-
Coloured ivory
-
IP63
OPTIONS -
BK Black versions for special order
-
W White versions for special order
- IS Intrinsically safe for special order (coloured ivory only)
DETECTOR BASES
Order Code
Description
Wgt (Kg)
FSCB1/D
Base with diode
FSCB1
Dimensions (mm)
Order Code
Description
Wgt (Kg)
Dia
C
0.05
100
8
FSCB1/D
Base with diode
Standard base
0.05
100
8
FSCB1
FSCB1/R
Non-latching relay base
0.10
100
13
FSCB1/LR/D
Latching relay base with diode
0.10
100
13
C
0.05
100
8
Standard base
0.05
100
8
FSCB1/R
Non-latching relay base
0.10
100
13
FSCB1/LR/D
Latching relay base with diode
0.10
100
13
C C C
-
-
+
+ Control panel
2
Dia Dia Dia
Dia
1
C C
Dimensions (mm)
2
2
2 1
1
Dia Dia
FSFH60
Dia
-
1
DETECTOR BASES
Control panel
9
Wgt (Kg)
Description
Dimensions (mm)
Wgt (Kg)
Operating voltage ~ 9.5 - 30V DC
CONVENTIONAL
CONVENTIONAL
Order Code
Dimensions (mm)
Order Code
-
10
INFINITY
INFINITY
FEATURES
FEATURES
-
EN54 Part 7 approved
-
EN54 Part 5 approved
-
Modern attractive design
-
Modern attractive design
-
Unique LED indicator design
-
Unique LED indicator design
-
Combined heat and smoke detector available
-
Remote LED output
-
Remote LED output
-
Anti tamper lock
-
Anti tamper lock
-
Built in 10 seconds
-
Built in 10 seconds alarm verification
alarm verification
SMOKE DETECTORS
HEAT DETECTORS
SPECIFICATION
SPECIFICATION
PDOS1
PDSH
-
Operating voltage ~ 10.5 - 33V DC
-
Operating voltage ~ 10.5 - 33V DC
-
Quiescent current (typical) ~ 120µA
-
Quiescent current (typical) ~ 120µA
-
Maximum current ~ 45mA
-
Maximum current ~ 45mA
-
Remote Indicator drive ~ 20mA (max)
-
Remote Indicator drive ~ 20mA (max)
-
Operating temperature ~ -10°C to + 50°C
-
Operating temperature ~ -20°C to + 60°C
-
Constructed from modified polycarbonate
-
Constructed from modified polycarbonate
-
Coloured white
-
Coloured white
-
IP43
-
IP43
polycarbonate
11
Dia
Description
Wgt (Kg)
PDOS1
Optical smoke detector
PDSH
Smoke and heat detector
Dia
-
Quiescent current (typical) ~ 120µA
-
Maximum current ~ 45mA
-
Remote Indicator drive ~
20mA (max)
-
Operating temperature ~
-10°C to + 50°C
-
Constructed from modified
-
Coloured white
-
IP43
INFINITY HEAT DETECTOR
Order Code
C
Operating voltage ~ 10.5 - 33V DC
C
Dimensions (mm)
Order Code
Description
Alarm condition
Wgt (Kg)
Dia
C
0.1
98
40
PDFH90
Fixed heat detector
Trigger 90°C
0.1
98
51
PDRR60
Rate of rise detector
Trigger 57°C
Dia
C
Dimensions (mm) Dia
C
0.08
98
40
0.08
98
40
CONVENTIONAL
CONVENTIONAL
INFINITY SMOKE DETECTOR
-
12
INFINITY BASES
FEATURES -
Relay base allows control of other equipment
-
Built in Diode for head removal
-
Sounder base has 8 selectable tones
-
Large cut out for easy cable entry
SPECIFICATION
PDCB1/D
-
Operating voltage ~ 9 - 28V DC
-
Operating temperature ~ -10°C to + 55°C
-
Base fixing centres ~ 41 - 70mm
-
Constructed from modified polycarbonate
-
Coloured white
PDCB1/R
1. Asperation Site Photo (The Big Blue)
PDSFB
Description
Contacts
Sound output dB @ 1m
Wgt (kg)
PDCB1/D
Common Base
-
-
0.10
PDCB1/R
Relay Base
NO C NC
-
0.10
PDSB
Sounder Base
-
89
0.15
PDSFB
Sounder Flasher Base
-
89
0.16
DIMENSIONS (mm)
C
Order code
Dia
C
PDCB1/D
100
25
PDCB1/R
100
25
PDSB
100
39
PDSFB
100
39
CONVENTIONAL
Dia
* L1 O
L1 O
UT
UT
L2
L2
-
L2
L2
UT
SND+ SND -
--+
+ -R
1234
-R
Control panel
--+
L1 I N
+
L1 I N
L1 I N
NO
C
NC
NO
C
+
NC
-R
-R
Control panel
L1 O
UT
1234
-
L1 O
PDCB1/D
13
PDSB
Order Codes
L1 I N
CONVENTIONAL
INFINITY BASES
+
PDSB/PDSFB
*Please note that the sounder base and the sounder flasher base still has to be wired to the sounder circuit and zone circuit
Firescan “Advantage” addressable installation at Hampton Manor Hotel, Solihull
14
UNIVERSAL
APPLICATION
FEATURES
FEATURES
CALL POINTS
-
CPD certified to EN54 part 11
-
Surface, flush, reusable or break glass
-
Activation LED indicator
-
Weatherproof option
-
Re-usable element
-
Clip on cover available
-
Unique test/reset/cover removal key
CALL POINTS
-
Surface, flush, reusable or break glass
-
Range of colours available for
specific applications
-
Unique test/reset/cover removal key
-
Clip on cover available
-
Re-usable element
-
Suitable for a range of applications
such as emergency door release
SPECIFICATION
SPECIFICATION
-
Operating voltage ~
FSUBG
FSRBG/S/IP67
up to 24V DC or 250V AC
-
Operating voltage ~ 9 - 30V DC
-
Operating voltage ~ 9 - 30V DC
-
Element type ~ glass
-
Fire triggering resistance ~ 470Ω/680Ω
-
Fire triggering resistance ~ 470Ω/680Ω
-
Operating temperature ~
-
Element type ~ plastic or glass
-
Element type ~ plastic
-10°C to + 55°C
-
Operating temperature ~ -10°C to + 55°C
-
Operating temperature ~ -25°C to + 70°C
-
NO,C,NC connections
-
ABS flame retardant
-
ABS flame retardant
-
ABS flame retardant
-
Coloured red
-
Coloured red
-
IP42
-
IP42
-
IP66
OPTIONS
15
APPLICATION CALL POINTS
B
Blue versions for special order
-
W
White versions for special order
-
Y
Yellow versions for special order
Order code
Description
Wgt (Kg)
FSUBG
Universal call point
0.19
Order code
Description
Wgt (Kg)
FSRBG/S/IP67
Weatherproof call point
0.29
FSACP/G
Green call point
0.19
CALL POINTS ACCESSORIES
DIMENSIONS (mm)
CALL POINTS ACCESSORIES
DIMENSIONS (mm)
Order code
Description
Order code
A
B
C
Order code
Description
Order code
A
B
C
FSRBG/ELE
Re-usable element
FSUBG
87
87
53
FSRBG/ELE
Re-usable element
FSACP/G
87
87
53
FSRRK1/FULL
Reset key
FSRBG/S/IP65
87
87
57
FSRRK1/FULL
Reset key
FSAG10
Pack of 10 break glasses
FSAG10
Pack of 10 break glasses
FSRBG/COVER
Clip on plastic protective cover
FSRBG/COVER
Clip on plastic protective cover
FSRBB
Back box only
FSRBB
Back box only
C
B
A
C
B
A
CONVENTIONAL
CONVENTIONAL
UNIVERSAL CALL POINTS
-
16
SOUNDERS
SOUNDERS
FEATURES
FEATURES
-
LPCB approved (FS109S only)
-
CPD certified to EN54 part 3
-
CPD certified to EN54 part 3
-
2 available tones
-
High sound output
-
Easy to install
-
32 selectable tones
-
Range of bases
-
Automatic synchronisation
-
Volume control -10dB adjustment
-
Second tone for two stage alarms
-
Easy to install
-
Range of bases
FS109S FS98S
SPECIFICATION
SPECIFICATION
-
Operating voltage ~ 9 - 28V DC
-
Operating voltage ~ 9 - 28V DC
-
Operating temperature ~
-
Operating temperature ~
-25°C to + 70°C (FS109S)
-10°C to + 55°C
-10°C to + 55°C (FSCS200)
-
Running current ~ 18mA
-
Running current ~ 16mA
-
ABS flame retardant
-
ABS flame retardant
-
Coloured red or white
-
Coloured red as standard (white optional) FSCS200
17
SOUNDERS
Order code
Description
IP rating
Sound output dB @ 1m
Wgt (Kg)
FS109S
Electronic sounder
IP54
102
0.17
FS109S/DP
Electronic sounder
IP65
102
0.20
FSCS200
Electronic sounder
IP54
100
0.20
OPTIONS
DIMENSIONS (mm) Order code
- W
White
-
UB
U-base cable entry/exit (FS109S only)
-
230
230V mains version (FS109S only)
Dia
FS96
C
FS109S
Dia
Dia 93
Description
IP rating
Sound output dB @ 1m
Wgt (Kg)
FS98S
Base sounder
IP54
93
0.11
FS96
Flush mounted sounder
IP33
96
0.15
OPTIONS * Note:
Colour must be specified when ordering
C
- W
White
63
- R
Red
FS109S/DP
93
121
FSCS200
96
62
C
Order code
-
BOX/R Red back box for FS96
-
BOX/W White back box for FS96
-
COV/R Red cover for FS98
-
COV/W White cover for FS98
DIMENSIONS (mm)
Dia
Order code
A
B
C
Dia
FS98S
-
-
30
112
FS96
86
86
36
-
C
A
B
C
CONVENTIONAL
CONVENTIONAL
SOUNDERS
18
SOUNDERS
BEACONS
FEATURES
FEATURES
-
High sound output
-
Automatic synchronisation
-
Low current consumption
-
High efficiency
-
Extensive choice of messages (FSVS1 only)
-
Choice of lens colours
-
Easy to install
and combinations
-
Easy to install
-
Suitable for outdoor use
AND BELLS
SPECIFICATION FS6B -
Operating voltage ~ 20 - 28V DC
-
Operating temperature ~ -10°C to + 55°C
-
Running current ~ 25mA
FS1ST/R
-
Steel gong and polycarbonate base construction
-
Operating voltage ~
9 - 60V DC
-
Operating temperature ~
-25°C to + 70°C
FSVS1
-
ABS flame retardant case with
-
Operating voltage ~ 15 - 30V DC
polycarbonate lens
-
Operating temperature ~ -20°C to + 70°C
-
Running current ~ 29mA
SPECIFICATION
-
10 selectable Tones
FS109S/ST/R
-
Constructed from ABS flame retardant
-
Operating voltage ~
9 - 28V DC
-
Operating temperature ~
-10°C to + 55°C
-
ABS flame retardant case with
polycarbonate lens
FS6B
SPECIFICATION
FS1ST/R
FSVS1
FS109S/ST/R
19
Order code
Description
IP rating
Sound output dB @ 1m
Wgt (Kg)
FS6B
Motorised bell
IP33
95
0.82
FSVS1
Voice sounder
IP66
97
0.22
BEACONS
DIMENSIONS (mm)
Dia
C
Dia
C
Order Code
Description
IP rating
Sound output dB @ 1m
Wgt (Kg)
Dimensions (mm) Dia
C
Order code
Dia
C
FS1ST/R
Red flashing beacon
IP54
N/A
0.15
93
62
FS6B
152
63
FS109S/ST/R
Electronic sounder/beacon
IP65
101
0.33
93
121
FSVS1
105
85
OPTIONS - A Amber - G Green - C Clear - B Blue -
UB
-
230 230V mains version
Dia
C
Dia
C
CONVENTIONAL
CONVENTIONAL
SOUNDERS AND BELLS
U-base version (FS1ST/R only)
20
TWINFLEX PRO FEATURES - LPCB and EN54 part 2 and 4 approved - 2, 4 and 8 zone panel - Ideal for HMOs - Quick and easy 2 wire installation - Detectors and sounders use the same 2 wires - Call point activation identified by panel - Key and code entry - 2 additional conventional sounder circuits - 4 line x 20 character LCD display - 500 event log - One-man test function
SPECIFICATION - Operating voltage ~ 230V AC @ 50/60Hz - System voltage ~ 24V DC nominal
FST-OUTM
- Dedicated Sounder circuit EOL ~ 10KΩ Resistor - Auxiliary fire relay ~ 1A @ 30V DC Max (Volt Free)
- Output module for use with door magnets and other automated devices
- Auxiliary fault relay ~ 1A @ 30V DC Max (Volt Free) - Remote Fire Output Load ~ 250mA 1Amp - Auxiliary supply ~ 21 - 30V DC (unregulated) - ABS flame retardant
DIMENSIONS (mm) A
B
C
331
331
99
A
C
FST200-2PRO
FST200-4PRO
FST200-8PRO
No. of detection circuits
2
4
8
No. of sounder circuits*
2 (+2)
4 (+2)
8 (+2)
Zone capacity
250mA (27 devices max)
250mA (27 devices max)
250mA (27 devices max)
Sounder circuit current
300mA per circuit
300mA per circuit
300mA per circuit
Supplied c/w batteries
2 x 3.4Ah 12V
2 x 3.4Ah 12V
2 x 3.4Ah 12V
Wgt (Kg) incl. batteries
4.85
4.88
4.96
*2 wire zones plus dedicated circuits
B
FIRE
FAULT
PROG INPUTS
NET A NET B SCRN NET A NET B MI/P+ MI/PSCRN 1+ 12+ 2Z4+ Z4SCRN Z3+ Z3SCRN Z2+ Z2SCN Z1+ Z1SCRN N/C N/0 COM N/C N/O COM MO1+ MO1SCRN MO2+ MO2SCRN AUX+ AUX1 SCRN BAT+ BAT24V IN 0V IN EARTH
21
Order codes
2 WIRE
2 WIRE
TWINFLEX PRO
22
TWINFLEX
TWINFLEX
FEATURES
FEATURES
-
EN54 compliant
-
EN54 compliant
-
7 modes of detection from 1 device
-
Stand alone sounder and strobes
-
Self calibrates every 6 hours
-
Wired to a zone
-
1 detector to suit all applications
-
Built in selectable end of line
-
Sounder built into the detectors
-
High sound output
-
Built in selectable end of line
DETECTORS AND CALL POINTS
SOUNDERS AND STROBES
SPECIFICATION
SPECIFICATION
FST-90S
FST-CHS/SND
-
Operating voltage ~ 18 - 35V DC
-
Operating voltage ~ 18 - 35V DC
-
Operating temperature ~
-
Operating temperature ~ -10°C to + 50°C
-10°C to + 50°C
-
ABS flame retardant
-
ABS flame retardant
-
Coloured white
-
Coloured red as standard
-
IP21
-
IP21
OPTIONS FST-95S/STR
FST-DBS
DETECTORS AND CALL POINTS
FST-BG
Order code
Description
Sound output dB @ 1m
Wgt (Kg)
FST-CHS
Heat and smoke detector c/w base
N/A
0.27
FST-CHS/SND
Heat and smoke detector c/w integral sounder and base
90 (HIGH) 75 (LOW)
FST-BG
Re-settable call point c/w back box
N/A
Order code
Description
Sound output dB @ 1m
Wgt (Kg)
FST-90S/R
Sounder
85
0.25
0.27
FST-DBS
High output sounder
103
0.35
0.28
FST-95S/STR
Sounder/strobe
90
0.32
DIMENSIONS (mm)
Order code
A
B
C
Dia
Order code
A
B
C
Dia
FST-CHS
-
-
61.5
105
FST-90S/R
85
85
60
-
FST-CHS/SND
-
-
61.5
105
FST-95S/STR
-
-
50
110
FST-BG
85
85
52
-
FST-DBS
-
-
60
100
Dia
A
C
B
C
A
B
C
Dia
C
Dia
C
2 WIRE
2 WIRE
White
SOUNDERS AND STROBES
DIMENSIONS (mm)
23
- W
24
SIMPLICITY
QUATTRO
FEATURES
FEATURES
- EN54 part 2 and 4 compliant
-
EN54 part 2 and 4 compliant
- 2,048 event log
-
1-250 Zones
- No additional software required
-
1-4 Loop cards
- Alpha numeric key pad
- 4,096 event log
- 4 x 20 character LCD display
-
- User programmable open protocol
- User programmable open protocol
- Simple to install
-
Key and coded access
- Key and coded access
-
Connection to PC via RS485 or USB
- RS232 printer port
-
Removable grommets on top of enclosure
- Removable grommets on top of enclosure
-
Rear cut out for hidden cable entry
- Rear cut out for hidden cable entry
SPECIFICATION
SPECIFICATION
-
Operating voltage ~
- Operating voltage ~ 230V AC @ 50/60Hz
230V AC @ 50/60Hz
- System voltage ~ 24V DC nominal
-
System voltage ~ 24V DC nominal
-
Charger voltage ~ 27.6V DC nominal
-
Charger voltage ~ 27.6V DC nominal
-
Auxiliary fire relay ~ 1A @ 30V DC Max (Volt Free)
-
Auxiliary fire relay ~
-
Auxiliary supply ~ 24V DC 500mA
1A @ 30V DC Max (Volt Free)
-
Metal enclosure
-
Auxiliary power supply ~
-
Powder coated grey
500mA @ 24V DC
-
Powder coated grey
QUATTRO
Order Codes
FSSIM-64/M
FSSIM-126/M
FSSIM-252/M
Order codes
QUATTRO-1
QUATTRO-2
QUATTRO-3
QUATTRO-4
No. of loops per panel
1
1
2
No. of loops per panel
1
2
3
4
No. of devices per loop
64
126
126
No. of devices per loop
125
125
125
125
No. of programmable zones
4
8
16
No. of programmable zones
1 - 250
1 - 250
1 - 250
1 - 250
Maximum loop length
1.5 km
1.5 km
1.5 km
Maximum loop length
2 km
2 km
2 km
2 km
Supplied c/w batteries
2 x 7.2Ah 12V
2 x 7.2Ah 12V
2 x 12Ah 12V
Supplied c/w batteries
2 x 7.2Ah 12V
2 x 12Ah 12V
2 x 17Ah 12V
2 x 17Ah 12V
Wgt (kg) incl. batteries
10.55
10.75
13.33
Wgt (kg) incl. batteries
15.72
18.50
21.90
22.10
REPEATER PANEL
REPEATER PANEL
Order code
Supply voltage
System voltage
Connections
Enclosure size (mm)
Wgt (kg)
Order code
Supply voltage
System voltage
Connections
Enclosure size (mm)
Wgt (kg)
FSSIM-RPT
20 - 30V DC
29V DC (Nominal)
RS485
355 x 275 x 70
1.00
QUATTRO-RPT
21- 30V DC
29V DC (Nominal)
RS485
375 x 335 x 125
5.30
DIMENSIONS (mm) A
B
C
375
335
125
A
FIRE FAULT
B
GND
RS485 1
A CTS TX RX DSR GND 1A- 1A+ 1B- 1B+ NO CM NC
PRINTER 2
3
C
FIRE RLY 4
NO CM NC -CLASS+
FAULT RLY 5
6
B
FIRE FAULT
FIRE FAULT
DIMENSIONS (mm) A
B
C
375
335
125
A
FIRE FAULT
TEST
TEST
TEST
TEST
DISABLE
DISABLE
DISABLE
DISABLE
B
C
ADDRESSABLE
ADDRESSABLE
SIMPLICITY
25
4 x 40 character LCD display
26
SIMPLICITY
SIMPLICITY
FEATURES
FEATURES
-
EN54 part 5 and 7 approved
-
LPCB and EN54 part 11 approved
-
Modern attractive design
-
Modern attractive design
-
Unique LED indicator design
-
Activation LED indicator
-
Combined heat and smoke
-
Back box with fixing screws
detector option available
-
Weatherproof version available
-
Remote led output
-
Anti tamper lock
-
Built in 10 seconds alarm verification
DETECTORS
DEVICES
FSSIM-ACP6
FSSIM-OPT64
SPECIFICATION
SPECIFICATION
-
Operating voltage ~ 17 - 28V DC
-
Operating voltage ~17-28V DC
-
Operating temperature ~
-
Operating temperature ~
-10°C to + 50°C
-10°C to + 50°C
-
ABS flame retardant
-
ABS flame retardant
-
Coloured white
-
IP67 (FSSIM-ACP7)
FSSIM-HTFH90
FSSIM-CDB64
27
SIMPLICITY AND QUATTRO DEVICES
Order code
Description
Maximum current alarm
Quiescent current (typical)
Wgt (kg)
FSSIM-OPT64
Optical smoke
5mA
500µA
0.09
FSSIM-CHS
Combined smoke and heat
5mA
500µA
0.09
FSSIM-HTFH90
Fixed heat
5mA
500µA
0.07
FSSIM-HTRR64
Rate of rise
5mA
500µA
0.07
DIMENSIONS (mm)
Dia
Order code
Dia
C
FSSIM-OPT64
98
40
FSSIM-CHS
98
51
FSSIM-HTFH90
98
FSSIM-HTRR64
98
C
Dia
C
Order code
Description
Quiescent current (typical)
Wgt (Kg)
FSSIM-ACP6
Call point
500µA
0.19
FSSIM-ACP7
WP call point
500µA
0.30
FSSIM-CDB64
Common base
-
0.05
FSSIM-CB/IS64
Isolator base
-
0.05
Dia
A
C
C
DIMENSIONS (mm) Order code
A
B
C
Dia
FSSIM-CDB64
-
-
24
100
FSSIM-CB/IS64
-
-
24
100
40
FSSIM-ACP6
87
87
58
-
40
FSSIM-ACP7
119
128
62
-
B
ADDRESSABLE
ADDRESSABLE
SIMPLICITY AND QUATTRO DETECTORS
28
SIMPLICITY
SIMPLICITY
FEATURES
FEATURES
-
EN54 compliant
-
EN54 compliant
-
Loop powered
-
Link external equipment to the loop
-
Selectable tones
-
Loop fault indication
-
Selectable sound levels
-
Fire indication
-
230V version available
SOUNDERS AND BEACONS
RELAY
SPECIFICATION
SPECIFICATION
-
Operating voltage ~ 17 - 33V DC
-
Operating voltage ~17 - 33V DC
-
Operating temperature ~ -10°C to + 50°C
-
Operating temperature ~
-
ABS flame retardant
0°C to + 50°C
-
White colour option on FSSIM-SUND95
-
Relay rating ~ 1 Amp SELV only
-
IP65 (FSSIM-SNDSTR/MAXI)
-
Input EOL ~ 47K
-
Alarm current ~ 10.6mA
-
Fault current ~ 2.8mA
-
Isolating current ~ 7.3mA
-
ABS flame retardant
-
Coloured white
-
IP43
FSSIM-SUND95
FSSIM-SNDSTR
FSSIM-MAXI
FSSIM-CB/SD64
FSSIM-CB/SF64
29
SIMPLICITY RELAY
Order code
Description
Maximum current alarm
Sound level dB @ 1m
Wgt (Kg)
FSSIM-SUND95
Wall sounder
12mA
95
FSSIM-SNDSTR
Wall sounder/beacon
15mA
FSSIM-MAXI
Wall sounder
FSSIM-CB/SD64 FSSIM-CB/SF64
Dimensions (mm) A
B
C
Dia
0.20
100
100
73
-
94
0.20
118
118
104
-
12mA
100
0.20
118
118
104
-
Base sounder
6mA
85
0.15
-
-
38
102
Base sounder/beacon
8mA
85
0.15
-
-
38
104
Order Code
Description
Quiescent Current (typical)
Wgt (Kg)
FSSIM-ZIOU
RELAY
900µA
0.22
DIMENSIONS (mm) A
B
C
A
B
C
DIA
A
C
B
C
A
B
C
127
88
59
ADDRESSABLE
ADDRESSABLE
SIMPLICITY SOUNDERS AND BEACONS
30
ADVANTAGE
DIMENSIONS (mm) Order code
A
B
C
FEATURES
FS2000-M101
345
320
88
FS2000-M202
450
475
125
- EN54 part 2 and 4 compliant
FS2000-M403
450
475
125
- 1-8 loop panels
FS2000-M404
450
475
125
- 240 x 64 pixel LCD display
A
- 200 Programmable zones
C
- 1,000 event log - Individual loop cards
B
- Optional printer - Auto learn facility - Configuration via PC through RS232 - Networking option up to 127 panels - 8 Loop option available - Zonal LED cards available - RS485 optional network card
SPECIFICATION - Operating voltage ~ 230V AC @ 50/60Hz - System voltage ~ 24V DC nominal - Charger voltage ~ 27.6V DC nominal - Maximum loop length ~ 2km - Auxiliary supply ~ 2 x 24V DC @ 500mA - Auxiliary contacts ~ 2 x 1A @ 30V DC - Dedicated sounder circuit ~ 2 x 1A @ 24V DC - Steel enclosure
31
ADDRESSABLE
ADDRESSABLE
- IP30
ADVANTAGE Order codes
FS2000-M101
FS2000-M202
FS2000-M403
FS2000-M404
No. of loops per panel
1
2
3
4
No. of devices per loop
Hochiki =127, Vista = 252 Max
ADVANTAGE COMPONENTS - FS2000-RCT
Remote control terminal
- FS2000-MOD
Modem interface card
No. of programmable zones
100 Max
200 Max
200 Max
200 Max
- FS2000-MXP003
Network interface card
Supplied c/w batteries
2 x 7.2Ah 12V
2 x 12Ah 12V
2 x 17Ah 12V
2 x 17Ah 12V
- FS2000-50ZONE
50 zone LED card
No. of sounder circuits
2
4
4
4
- FS2000-PCNETT
Programming software and lead
Sounder circuit current
1A
1A
1A
1A
Protocols
Hochiki
Wgt (Kg) incl. batteries
10.60
Hochiki and Vista
17.40
20.80
NC
21.00
NO COM NC
NO COM UP MODE
LOCK MEM
OUT OUT IN + +
IN OUT OUT IN + +
IN -
32
HOCHIKI
HOCHIKI
FEATURES
FEATURES
-
LPCB & VdS approved
-
LPCB & VdS approved
-
Remote indicator output
-
Wide voltage range
-
Wide voltage range
-
Modern design
-
Twin fire LEDs allow 360° viewing
-
Re-settable element
-
Wide range of mounting bases
-
Addressed via hand held
-
Low profile modern design
programmer
-
Addressed via hand held programmer
-
Available in white
ADDRESSABLE DETECTORS
ADDRESSABLE DEVICES
FS2000-OSD3
FS2000-ACP3
SPECIFICATION
SPECIFICATION
-
Operating voltage ~17 - 41V DC
-
Operating voltage ~ 17 - 41V DC
-
Remote Indicator drive ~ 20mA (max)
-
Operating temperature ~
-
Operating temperature ~ -10°C to + 50°C
-10°C to + 50°C (call points)
-
ABS flame retardant
-10°C to + 50°C (bases)
-
Coloured ivory
-
ABS flame retardant
-
IP42 (FS2000-HDS5 IP64)
-
IP24 (FS2000-ACP3 only)
FS2000-HDS5
FS2000-AAB7
33
HOCHIKI ADDRESSABLE DEVICES
Order code
Description
Maximum current alarm
Quiescent current (typical)
Wgt (Kg)
Order code
Description
Maximum current alarm
Quiescent current (typical)
Wgt (Kg)
FS2000-OSD3
Smoke detector
9mA
400µA
0.09
FS2000-ACP3
Call point
5mA
220µA
0.16
FS2000-HDS5
Multi heat sensor
19mA
350µA
0.10
FS2000-ACPLI
Call point with isolator
10mA
250µA
0.16
FS2000-CHS
Smoke and heat detector
19mA
450µA
0.10
FS2000-AAB7
Common base
-
-
0.50
FS2000-AAB8
Isolator base
-
50µA
0.85
HOCHIKI ACCESSORIES - FS2000-ASX
Hand held programmer
Dia
DIMENSIONS (mm)
Dia Dia
C C
Dia Dia Dia
A
C
C C C
C
DIMENSIONS (mm) Order code
A
B
C
Dia
FS2000-AAB7
-
-
12
100
FS2000-AAB8
-
-
12
100
Order code
Dia
C
FS2000-OSD3
100
43
FS2000-HDS5
100
43
FS2000-ACP3
89
93
60
-
FS2000-CHS
100
51
FS2000-ACPLI
89
93
60
-
B
ADDRESSABLE
ADDRESSABLE
HOCHIKI ADDRESSABLE DETECTORS
34
HOCHIKI
ADDRESSABLE SOUNDERS AND RELAYS
FEATURES -
LPCB and EN54 approved
-
Loop powered
-
Single address
-
Auxiliary monitored input
-
Selectable sound levels
-
IP65 weatherproof kit available for wall sounders
FS2000-LWS
SPECIFICATION -
Operating voltage ~ 17 - 41V DC
-
Operating temperature ~
-10°C to + 50°C
-
Relay contact rating ~
1A @ 30V DC max (FS2000-DRM only)
-
ABS flame retardant
-
White colour option on FS2000-WSB/LWS
FS2000-WSB
FS2000-LPS
FS2000-LPSB
FS2000-DRM
1. Asperation Site Photo (The Big Blue)
35
Maximum Quiescent current current alarm (typical)
Sound level dB @ 1m
Wgt (Kg)
200µA
90-102dB
13mA
200µA
Base sounder
16mA
FS2000-LPSB
Base sounder/beacon
FS2000-DRM
Dual relay module
Order code
Description
FS2000-LWS
Wall sounder
8mA
FS2000-WSB
Wall sounder/beacon
FS2000-LPS
C
Dia
Dimensions (mm) A
B
C
Dia
0.15
-
-
68
112
90-102dB
0.16
-
-
68
112
150µA
50-98dB
0.11
-
-
43
113
21mA
250µA
50-98dB
0.16
-
-
43
113
22mA
300µA
-
0.34
157
127
35
-
Dia
A
C
ADDRESSABLE
ADDRESSABLE
HOCHIKI ADDRESSABLE SOUNDERS AND RELAYS
C
B Firescan aspirating system installed at WH Smith Distribution Centre, Birmingham
36
VISTA
VISTA
ADDRESSABLE DEVICES
ADDRESSABLE SOUNDERS AND RELAYS
FEATURES
FEATURES
-
-
EN54 compliant
-
High sound output
-
Low current consumption
-
Incorporated isolators in all devices
-
All devices addressed via hand
held programmer
-
LED indication for fire and fault
LPCB and EN54 approved
-
Low current consumption
-
Remote indicator output
-
Wide voltage range
-
Fire LED allows 360° viewing
-
Modern design
-
Addressed via hand
held programmer
FSVA-WS
FSVA-OPT
SPECIFICATION
SPECIFICATION
-
Operating voltage ~ 15 - 40V DC
-
Operating voltage ~ 15 - 40V DC
-
Operating temperature ~
-
Operating temperature ~
-30°C to + 70°C
-25°C to + 60°C
-20°C to + 60°C (call point)
-
Relay contact rating ~
-
ABS flame retardant
2A @ 30V DC max (FSVA-DRM)
-
ABS flame retardant
FSVA-CB
FSVA-CP FSVA-WSB
37
Order code
Description
FSVA-OPT
Smoke detector
6mA
90µA
IP42
FSVA-HS
Multi heat sensor
6mA
70µA
FSVA-CHS
Multi sensor
6mA
FSVA-CP
Call point
FSVA-CB
Common base
C
Dia
FSVA-DRM
VISTA ADDRESSABLE SOUNDERS AND RELAYS
Maximum current alarm
Dia
FSVA-LPSB
Quiescent current (typical)
IP rating
Wgt (Kg)
Dimensions (mm) A
B
C
Dia
0.09
-
-
54
110
IP52
0.09
-
-
54
110
90µA
IP42
0.09
-
-
54
110
6mA
70µA
IP54
0.18
87
87
56
-
-
-
-
0.05
-
-
16
110
A
C
Sound level dB @ 1m
Wgt (Kg)
70µA
100dB
7mA
70µA
Base sounder
8mA
FSVA-LPSB
Base sounder/beacon
FSVA-DRM
Dual relay module
Description
FSVA-WS
Wall sounder
7mA
FSVA-WSB
Wall sounder/beacon
FSVA-LPS
Dimensions (mm) A
B
C
Dia
0.23
-
-
96
108
100dB
0.23
-
-
96
108
-
88-95dB
0.12
-
-
40
115
11mA
-
88-95dB
0.20
-
-
56
142
6mA
120µA
-
0.08
87
87
40
-
C Dia
B
Maximum Quiescent current current alarm (typical)
Order code
C
Dia
C
Dia
A
C
C
ADDRESSABLE
ADDRESSABLE
VISTA ADDRESSABLE DEVICES
FSVA-LPS
B
38
MOTORISED
ASPIRATION
BEAM DETECTORS
System
FEATURES FEATURES
-
EN54 part 12 approved
-
VdS and CPD approved
-
Compatible with conventional
-
VdS approved
and addressable systems
-
Compatible with conventional
-
Self aligning
and addressable systems
-
Easy to install
-
Can be used for heights
-
Colour coded installation
up to 21 metres
-
Low current consumption
-
Up to 100 metres coverage in length
-
Fault indication for air flow
-
Fire and fault indication
-
Coded access
-
Can be used up to a height of 40 metres
-
A range of accessories available
-
Low level controller for easy commissioning
SPECIFICATION
SPECIFICATION
-
Operating temperature ~
-10°C to + 50°C
-
Pipe diameter ~ 25mm
-
Pipe length ~ 100m Max
-
Alarm indication via detector
-
Operating temperature ~
-10°C to + 55°C
-
ABS flame retardant
-
Coloured grey
-
Coloured white
-
IP65
-
IP65
FSRP80-100*
FSRP40-80*
Description
Detection range
Maximum current alarm
Quiescent current (typical)
Fire/fault contact rating
Wgt (Kg)
FSSCBD
Beam head and controller
5-40 metres
3mA
3mA
2A @ 30V DC
1.60
FSRP40-80
Mid range reflector
40-80 metres
-
-
-
0.80
FSRP80-100
Long range reflector
80-100 metres
-
-
-
1.80
FSAB
Adjustable bracket
-
-
-
-
0.60
Order code
DIMENSIONS (mm)
A
Order Code
A
B
C
FSSCBD (beam head)
155
182
137
FSSCBD (controller)
120
166
62
FSRP40-80
293
293
5
FSRP80-100
394
394
5
FSAB
120
150
100
B
A
C
B
C
ASPIRATION SYSTEM Order code
Description
Current
Number of pipe outlets
Wgt (kg)
FSASD1
1 Detector aspirator
300mA max
1
0.90
FSASD2
2 Detector aspirator
300mA max
2
0.90
HOCHIKI ACCESSORIES
DIMENSIONS (mm) Order code
A
B
C
End cap
FSASD1
259
183
166
- ASPCLIP
Pipe clip
FSASD2
259
183
166
- ASPIPE
3m pipe 25mm
- ASSOCKET
Socket for pipe
- ASCUTTER
Pipe cutters
- ASSOLVENT
Solvent cement
- ASTEE
Connector T shape
- ASWARN
Sample hole warning labels (100)
- AS90BEND
90 degree bend
- ASENDCAP
A
B
C
SPECIALIST EQUIPMENT
Operating voltage ~ 10 - 40V DC
MOTORISED BEAM DETECTORS
SPE
Operating voltage ~ 18 - 30V DC
-
*Reflector supplied with beam head completes the reflector array
39
-
40
POWER SUPPLIES
RELAYS
FEATURES
FEATURES
-
Mains on LED Indication (GREEN)
-
Removable grommets for
-
Fault LED Indication (RED)
cable entry
-
Battery back up facility
-
Large terminals can accommodate
2 x 2.5mm² cables
SPECIFICATION -
Operating voltage ~ 230V DC
-
Operating temperature ~ -20°C to + 40°C
SPECIFICATION FSPSU1A/7
-
Output voltage ~27.6V DC nominal
-
Battery back up ~ 2 x 12V - 7.2 Amp-hours
-
Steel enclosure
-
Coloured white
-
IP42
A
FSRHD2
C A
C
B B
41
Operating voltage ~ 24V DC
-
Operating temperature ~
-
-10°C to + 50°C
-
Contact rating ~ 5A @ 230V AC
-
2 sets of contacts NO,C,NC
-
ABS flame retardant
-
Coloured grey
-
IP65
Dimensions (mm)
Order Code
Description
Supplied c/w batteries
Wgt (Kg)
A
B
C
FSPSU1A/7
1 Amp power supply
2 x 7.2Ah 12V
8.32
295
330
80
FSPSU2A/7
2 Amp power supply
2 x 7.2Ah 12V
8.92
295
330
80
FSPSU3A/7
3 Amp power supply
2 x 7.2Ah 12V
9.02
295
330
80
FSPSU5A/7
5 Amp power supply
2 x 7.2Ah 12V
9.12
295
330
80
HEAVY DUTY RELAY UNIT Order Code
Description
Wgt (Kg)
FSRHD2
HEAVY DUTY RELAY UNIT
0.60
Dimensions (mm) A
B
C
145
170
86
FEATURES
FEATURES
-
Can operate up to 7 Door Magnets
-
Semi flush
-
Removable grommets for cable entry
-
Fits a single gang back box
-
Large terminals can accommodate
2 x 2.5mm² cables
SPECIFICATION
SPECIFICATION
-
Operating voltage ~ 24V DC
-
Operating temperature ~
-10°C to + 40°C
Output voltage ~ 24V DC (unregulated)
-
Contact rating ~ 5 Amp @ 230V AC
-
2 sets of contacts NO,C,NC
-
ABS flame retardant
-
ABS flame retardant
-
Coloured grey
-
IP65
-
Operating voltage ~ 230V DC
-
Operating temperature ~ -10°C to + 50°C
-
A
FSAP1
C
B
Description
FSAP1
Auxiliary power supply for door magnets
C
FSFRP4
B
DOOR MAGNET POWER SUPPLY Order Code
A
-
Coloured grey
-
IP42
SINGLE GANG RELAY PLATE Wgt (Kg) 1.24
Dimensions (mm) A
B
C
Order Code
Description
Wgt (Kg)
180
245
85
FSFRP4
Single gang relay plate
0.09
Dimensions (mm) A
B
C
86
86
15
ANCILLARY EQUIPMENT
ANCILLARY EQUIPMENT
POWER SUPPLY UNIT
-
42
DOOR
ANCILLARIES
FEATURES
FEATURES
-
EN1155 compliant
-
-
Strong holding force
detectors
-
Low current consumption
-
-
Robust design
-
Adjustable keeper plate
-
Integrated release button
MAGNETS
A
-
Operating voltage ~
24V DC (FSDH24)
230V AC (FSDH240)
-
Operating temperature ~ 0°C to + 30°C
-
Rated holding force ~ 200N
-
Residual holding force ~ zero
-
Coloured white
ANCILLARY EQUIPMENT
-
Operating voltage ~ 5 - 24V DC
C
-
Operating temperature ~
-10°C to + 40°C
-
Maximum current ~ 24mA
-
ABS flame retardant
-
IP42
REMOTE INDICATOR UNIT
Order code
Description
Nominal current (mA)
Wgt (Kg)
FSDH24
24V DC door magnet
50
0.46
FDDH240
230V AC door magnet
12
0.46
Order Code
Description
Wgt (Kg)
FSR1
Remote indicator unit
0.04
C
MAGNET ENCLOSURE
80
80
56
KEEPER PLATE
70
70
40
A
A
C
C
MAINS ISOLATOR SWITCH B
B
86
86
12
Essential for local mains power
-
Mains neon indication
-
Surface mount
-
20mm knockouts
-
Supplied with 13A fuse
SPECIFICATION
FSRPE5142
B C
C
isolation
DIMENSIONS (mm) B
B
-
Floor mounting bracket
A
A
FEATURES
DOOR MAGNET ACCESSORIES
Part
Dimensions (mm)
Order Code
Description
Wgt (Kg)
FSRPE5142
Mains isolator switch
0.26
-
Operating voltage ~ 230V AC
-
Operating temperature ~
-10°C to + 40°C
-
Maximum current ~ 13A
-
Metal enclosure
-
Coloured red
-
IP21 Dimensions (mm) A
B
C
87
87
45
ANCILLARY EQUIPMENT
43
FSR1
B
DOOR MAGNET
A
For use in roof voids , lift shafts etc.
SPECIFICATION
SPECIFICATION
- FSDHB3
Indication of hidden active
44
A basic guide
SYSTEM
to fire alarm system design
There are a number of documented standards that should be considered during the design and selection of the components that form the vital fire detection system. The Regulatory Reform (Fire Safety) Order 2005 and the Fire (Scotland) Act 2005 covers fire safety requirements applicable in the UK. The Fire Safety Regulatory Reform Order (RRO) applies to all premises where people meet, for example every office, shop, factory, warehouse, public residential premises including care homes, educational premises, restaurants, public houses, theatres, cinemas, stadiums, hospitals and public transport premises.
WIRING CONFIGURATION CONVENTIONAL SYSTEM (INFINITY and OPTIMA)
2 WIRE (TWINFLEX)
EOL
Compliance with the Fire Safety RRO is ensured through a Fire Risk Assessment by a “Competent Person” organised by the “Responsible Person” typically being the landlord, owner, occupier or manager. Related current industry standards must be used to ensure premises are appropriately and suitably equipped. Some industry standards for Fire detection systems at the time of this publication are:-
EOL EOL
-
BS5839-1:2002+A2:2008 Fire detection and fire alarm systems for buildings. Code of practice for system design, installation, commissioning and maintenance.
-
BS5839-6:2004 Fire detection and fire alarm systems for buildings. Code of practice for the design and installation of fire detection and fire alarm systems in dwellings.
For specific systems and components -
BS EN 54 Parts 1 to 25 covers a multitude of systems and devices including panels, detectors, call points, sounders, beam detectors and aspirating systems.
EOL
EOL Built in
Radial circuits terminated by EOL (End Of Line) device. Must have a minimum of two sounder circuits.
Radial circuits terminated by built in EOL (End Of Line) device. Must have a minimum of two sounder circuits.
ADDRESSABLE (QUATTRO and ADVANTAGE)
Industry standard third party accreditation e.g. CPD (Construction Products Directive) and LPCB (Loss Prevention Certification Board) approvals, ensures the reliability of the equipment, being fit for purpose, and compliant with the law.
*
SYSTEM ZONING AND LAYOUT It is recommended that one of the first stages in fire alarm system design is to divide the property into precise areas or detection zones. This is a fairly straightforward process so long as the following criteria is adhered to: -
A zone should not extend beyond a single fire compartment.
-
The floor area of a zone should not exceed 2000m² other than an open plan area (e.g. uncompartmented warehouse) which should not exceed 10,000m².
-
A zone should not extend beyond a single floor area, therefore each floor level in a building will constitute at least one zone.
-
As an exception to the above, stairwells, lift shafts and other vertical shafts should be designated as an individual zone.
-
Small premises with multiple floor levels not exceeding an area of 300m² in total may be considered as a single zone.
-
The search distance in a zone should not exceed 60m from point of entry, i.e. that distance which needs to be travelled for a searcher to visually establish the position of the fire.
*INCORPORATED LOOP ISOLATOR
Ring or loop circuit.
COMPATIBILITY GUIDE System panel
Detectors and bases
Call points
Sounders and beacons
Infinity and Optima
Conventional
FSV-OPT, FSV-CDB, FSV-DDB, FSV-RDB, FSV-FH78, FSV-RR58, FSOS2, FSIRFD, FSCB1/D, FSCB1, FSCB1/R, FSCB1/LR/D, FSFH60, FSFH90, FSRR60, FSRR90, PDOS1, PDSH, PDFH90, PDRR60, PDCB1/D, PDCB1/R, PDSB
FSUBG, FSRBG/S/IP67, FSRBG/ELE, FSAG10, FSRBB, FSRBG/COVER, FSRRK1/FULL
FS109S, FS109S/DP, FSCS200, FS98S, FS96, FS6B, FSVS1, FS1ST/R, FS109S/ST/R
Twinflex
2 wire
FST-CHS, FST-CHS/SND
FST-BG
FST-90S/R, FST-DBS, FST-95S/STR
Simplicity and Quattro
Addressable
FSSIM-OPT64, FSSIM-CHS, FSSIM-HTFH90, FSSIM-HTRR64, FSSIM-CDB64, FSSIM-CB/IS64
FSSIM-ACP6, FSSIM-ACP7
Whilst an optical detector provides the highest level of protection for point detectors it is susceptible to airborne contamination through dust or smoke generated typically in certain areas of manufacturing and kitchens. Careful consideration must be given to the selection of the most suitable detector for its particular environment. Whilst the best level of protection can be achieved with smoke detectors repeated false alarms may become a nuisance to the point that the alarm could be ignored, even disabled, with obvious risks to life, safety and property protection.
FSSIM-SUND95, FSSIM-SNDSTR, FSSIM-MAXI,FSSIM-CB/SD64, FSSIM-CB/SF64
Advantage
Addressable Hochiki (ESP) protocol
FS2000-OSD3, FS2000-HDS5, FS2000-CHS, FS2000-AAB7, FS2000-AAB8
FS2000-ACP3
FS2000-LWS, FS2000-WSB, FS2000-LPS, FS2000-LPSB
The Firescan design service will be pleased to give qualified advice on any specific application.
Advantage
Addressable Vista (Vega) protocol
FSVA-OPT, FSVA-HS, FSVA-CHS, FSVA-CB
FSVA-CP
FSVA-WS, FSVA-WSB, FSVA-LPS, FSVA-LPSB
The various types of heat and smoke detectors are summarised below: OPTICAL (photoelectric) type smoke detectors provide the best method of smoke detection in stairwells, corridors, sleeping areas. They are designed to detect smoke particles that can be expected in such areas from smouldering and developing fires. FIXED TEMPERATURE heat detectors will operate when their rated temperature is exceeded. They are ideally suited to kitchen areas, boiler rooms, and hot industrial environments. RATE-OF-RISE heat detectors will detect an abnormally rapid heat build up that might be expected to occur under fire conditions.
TECHNICAL
TECHNICAL
PC LAN connection
System Type
NOTE: This can be made less complex with the use of remote indicators removing the necessity to open every door and inspect each room in a zoned area. Zoning should further take account of accessibility into an area and the heightened importance of any specific areas. On conventional control panels, zoning will also isolate the effects of faults occurring to a specific zone from the other circuits (on addressable systems, short circuit loop isolators will be needed to perform the same function on a specific loop).
45
*
46
SYSTEM DESIGN
SYSTEM DESIGN
BS5839 PART1:2002 + A2:2008
P AFD* designed to primarily protect property P1 AFD* installed throughout all areas P2 AFD* installed only in defined areas
P1
L4 L3 L1
P2
L2
L L1 L2 L3 L4 L5 M
AFD* designed to primarily protect Human Life AFD* installed throughout all areas AFD* installed in defined areas in addition to L3 AFD* installed in escape routes and rooms opening onto these routes AFD* installed in escape routes comprising circulation areas and spaces such as corridors and stairways Protected area is designed to satisfy a specific fire risk objective other than that of L1 to L4 System designed to be manually operated (no AFD*)
*
AFD = Automatic Fire Detection
MINIMUM SOUND LEVELS The minimum sound level of a sounder device should be 65dB(A) or 5dB(A) above a background noise which is louder than 60dB(A) (if lasting more than 30 seconds) and at a frequency of between 500Hz and 1000Hz.
Heat detectors BS EN 54-5 grade 1
Point smoke detectors
65dB(A) @ 500Hz to 1000Hz
General limits
Rapid attendance
9.0 7.5
13.5 12.0
Class A1 Other classes
Background noise
Aspirating smoke Detection systems (category 1)
+5dB(A) @ 500Hz to 1000Hz
For ceilings that feature an apex: as long as the height of the apex from the rest of the ceiling is less than 150mm for Heat detectors or less than 600mm for Smoke detectors then these can be treated the same as flat ceilings.
Ceiling heights (m)
Detector type
Optical beam smoke detectors BS5839: Part 5
10.5
15.0
Normal 10.5 Enhanced 12.0 Very high 15.0
Normal 15.0 Enhanced 17.0 Very high 21.0
25.0
40.0
For higher apexes, a device should be installed at the highest point. The distance to adjacent devices can be increased by 1% per degree of angle of the roof up to a maximum of 25%.
DEVICE CABLING Sounder device cabling should be arranged so that in the event of a fault at least one sounder will remain operational during a fire condition.
7.5m
7.5m
7.5m
5.3m
5.3m
2m
X
15m
5.3m
15m
10.6m
SMOKE DEVICES
10.6m HEAT DEVICES
<500mm
BEAM
<300mm
AIR VENT/AIR CON
>800mm
2m
47
Manual Call points should be positioned 1.4m (+/-200mm) from floor level. Any nonmechanically protected cable medium should have additional protection.
Voids less than 800mm in height need not have independent coverage, unless fire or smoke is able to spread from one area to another through the void or risk assessment shows AFD (Automatic Fire Detection) to be necessary.
Unless MICC cable is used, all cabling should be mechanically protected from floor level up to a height of 2m.
>150mm
LIFT SHAFTS 5.3m
7.5m
HEAT DEVICES
SMOKE DEVICES
60m MAX
>2.1m
1.5m 5.3m
A person searching a Zone for a fire should not have to travel more than 60m to identify the source of a fire.
10.6m
10.6m x 10.6m = 112m²
Smoke detection devices have an individual coverage of 7.5m radius. However these radii must overlap to ensure there are no ‘blind spots’.
3.8m
7.5m
7.5m x 7.5m = 56.3m²
Heat detection devices have an individual coverage of 5.3m radius. However these radii must overlap to ensure there are no ‘blind spots’.
Vertical shafts like lifts and stairways should have a device mounted within 1.5m of any opening.
Enclosed stairways should have a detector on each main landing.
Visual alarms such as strobes should always be mounted above 2.1m from floor level but never closer than 150mm to the ceiling.
TECHNICAL
TECHNICAL
A device should not be mounted within 500mm of any obstruction. If the top of a solid partition is less than 300mm from ceiling then treat it as a wall. Similarly, ceiling obstructions such as beams should be treated as walls if deeper than 10% of the ceiling height. A person should not have to travel more than 45m along an escape route to reach a Manual Call Point. Manual Call Points should be sited at all stair wells and exits from the building.
LIGHT FITTING
<200mm
Never mount devices closer than twice the depth of light fittings.
PARTITION
1.4m (+/-200mm)
At no stage should detectors be mounted less than 1m from air Inlets or air conditioning units.
>10% Ceiling height
FIRE DOOR
75dB(A)
Decibel loss occurs through doors: approximately -20dB(A) through a normal door, and approximately -30dB(A) through a fire door.
45m MAX
>1m
-30dB(A)
<500mm
For areas where people are sleeping, sounder devices should produce a minimum of 75dB(A) at the bed-head with all doors shut.
2m
In corridors less than 2m wide the horizontal spacing of detectors may be increased, the areas of coverage need not overlap as in the case of a room. Any corridor over 2m wide is deemed a room and device spacing should follow the standard for rooms (previous page).
-20dB(A)
<1m
100mm
Fire Alarm and Detection systems are categorised in the following way:
BS5839 PART1:2002 + A2:2008
48
INDEX
DISTRIBUTOR
Order code
Page Number
Order code
Page Number
Order code
Page Number
AS90BEND
40
FSCB1/R
9
FSSIM-MAXI
29
ASCUTTER
40
FSCS200
17
FSSIM-OPT64
27
ASENDCAP
40
FSDH24
43
FSSIM-RPT
25
ASPCLIP
40
FSFH60
10
FSSIM-SNDSTR
29
ASPIPE
40
FSFH90
10
FSSIM-SUND95
29
ASSOCKET
40
FSFRP4
42
FSSIM-ZIOU
30
ASSOLVENT
40
FSINF-2
3
FST200-2PRO
21
ASTEE
40
FSINF-4
3
FST200-4PRO
21
ASWARN
40
FSINF-6
3
FST200-8PRO
21
FDDH240
43
FSINF-8
3
FST-90S/R
24
FS109S
17
FSIRFD
9
FST-95S/STR
24
FS109S/DP
17
FSOPT-2
5
FST-BG
23
FS109S/ST/R
20
FSOPT-4
5
FST-CHS
23
FS1ST/R
20
FSOPT-6
5
FST-CHS/SND
23
FS2000-50 ZONE
31
FSOPT-8
5
FST-DBS
24
FS2000-AAB7
34
FSOS2
9
FSUBG
15
FS2000-AAB8
34
FSPSU1A/7
41
FSVA-CB
37
FS2000-ACP3
34
FSPSU2A/7
41
FSVA-CHS
37
FS2000-ACPLI
34
FSPSU3A/7
41
FSVA-CP
37
FS2000-CHS
33
FSPSU5A/7
41
FSVA-DRM
38
FS2000-HDS5
33
FSR1
44
FSVA-HS
37
FS2000-LPS
35
FSRBB
15
FSVA-LPS
38
FS2000-LPSB
35
FSRBG/COVER
15
FSVA-LPSB
38
All products are distributed through the UK’s largest network of wholesale outlets: City Electrical Factors with over 400 branches in the British Isles and almost 1,000 more premises in mainland Europe, the Middle East, North America and Australia. Each branch provides the customer with a service that is second to none as well as stocking a wide range of Tamlite Lighting products. www.cef.co.uk
FIRESCAN. CO.UK Visit our all new website to browse all of our products and be updated on our latest news and services available from Tamlite Emergency and Fire.
49
FS2000-LWS
35
FSRBG/ELE
15
FSVA-OPT
37
FS2000-M101
31
FSRBG/S/IP67
15
FSVA-WS
38
FS2000-M202
31
FSRHD2
42
FSVA-WSB
38
FS2000-M403
31
FSRP40-80
39
FSV-CDB
7
simus magnis ra deles debis mil et et, est et que nis millo ex estota
FS2000-M404
31
FSRP80-100
39
FSV-DDB
7
estiis ex explitae.
FS2000-MOD
31
FSRPE5142
44
FSV-FH78
8
FS2000-MXP003
31
FSRR60
10
FSV-OPT
7
NEWS
LATEST PRODUCTS
PROJECTS
Am velentiasi re nihiliq uissus porion ea abo. Itasper natiatias et, serum faceprem is eaqui consequam et quate corrunt aut enimolu trupt atempore culparum cust, unto volorer spicate quiam Read More
Am velentiasi re nihiliq uissus porion ea abo. consequam et quate corrunt aut enimolu mquodi auda dolorer ionsenis enetus qui rem trupt atempore culparum cust, unto volorer spicate quiam Read More
Am velentiasi re nihiliq uissus porion ea abo. consequam et quate corrunt aut enimolu mquodi auda dolorer ionsenis enetus qui rem trupt atempore culparum cust, unto volorer spicate quiam Read More
FS2000-OSD3
33
FSRR90
10
FSV-RDB
7
FS2000-PCNETT
31
FSRRK1/FULL
15
FSV-RR58
8
FS2000-RCT
31
FSSCBD
39
FSVS1
19
FS2000-ROM7
35
FSSCBD/AP
39
PDCB1/D
13
FS2000-WSB
35
FSSIM-126/M
25
PDCB1/R
13
FS6B
19
FSSIM-252/M
25
PDFH90
12
FS96
18
FSSIM-64/M
25
PDOS1
11
FS98S
18
FSSIM-ACP6
28
PDRR60
12
FSACP/G
16
FSSIM-ACP7
28
PDSB
13
FSAG10
15
FSSIM-CB/IS64
28
PDSFB
13
FSAP1
41
FSSIM-CB/SD64
29
PDSH
11
FSASD1
40
FSSIM-CB/SF64
29
QUATTRO-1
26
FSASD2
40
FSSIM-CDB64
28
QUATTRO-2
26
FSCB1
9
FSSIM-CHS
27
QUATTRO-3
26
FSCB1/D
9
FSSIM-HTRR64
27
QUATTRO-4
26
FSCB1/LR/D
9
FSSIM-HTFH90
27
QUATTRO-RPT
26
WELCOME Tiunti as dus reicienis reperio nsedit que rem labo. Et pratia nis eostius quam sitaspiet laut et quam, cum et volupta quibus accum parum, coreped itaeped mo mo blabor reprae. Uga. Itas culparibus
View Basket
Tell a friend
Bookmark
Join Our Mailing List
Links
Mission Startement
© Saldon Products Ltd trading as Tamlite Lighting
Terms & Conditions
Privacy Policy
The Tamlite Lighting policy of continuous improvement and development may mean certain products are not featured in this publication and that specifications
TECHNICAL
TECHNICAL
HOME II ABOUT US II PRODUCTS II TECHNICAL II DISTRIBUTOR II CONTACT US
may change or items be discontinued. General specifications shall not form part of any contract. All goods supplied are subject to Tamlite Lighting’s General Conditions of Sale, a copy of which is available on request. Illustrations have been used as a guide to product identification and dimensions, they may not be accurate in every detail. Technical data provided is typical and for guidance only. The manufacturer reserves the right to alter specifications without prior notice.
50
