Transcript
Engine
Model:
Deutz F4L912
Configuration:
4 cylinder, in-line, air cooled with integrated blower fan
Engine Capacity:
3.770 l
Governed Power:
46 kW
Max. torque:
230 Nm @ 1 500 rpm
Governed full Power Engine Speed:
2 150 rpm
Max. Rated Speed:
2 500 rpm
Aspiration:
Naturally aspirated
Frame Mounting:
3 point rigid mounting
Sump material:
Cast Aluminium
Oil Capacity:
9l
Blower failure warning:
Mechanical linkage induces injector pump shutoff
Low idle:
800 rpm
High idle:
2 250 rpm
Fuel filtration:
Two stage. Spin-on water separator primary, replaceable spin-on secondary
Oil filtration:
Replaceable spin-on paper-type micro filter- full flow
Exhaust
Type:
Rigid frame mounted stainless steel vertical silencerwith short stack pipe outlet
Air Cleaner
Type:
Dual (primary & safety) paper element cyclonic canister type with restriction visual indicator
Pre Cleaner System
Type:
Cyclonic dust bowl
Fuel Inlet System
Water separator primary filter- spin-on:
Frame mounted, 5 micron
Secondary filter- spin-on:
Frame mounted, 5 micron
Engine/Trans. Coupling
Type:
Bell nylon gear coupling
Drive Pumps
Model: Type:
Eaton 78363 Axial piston, closed loop, manualcontrol swash plate
Control:
Direct control, foot lonkage
Pump Displacement:
40.6 cc/rev per wheel
Relief pressure:
276 bar
Flow rate at governed RPM:
87.29 l/min per wheel
Drive Motors
Model:
Eaton 74318
Type:
Axial piston, closed loop
Transmission Charge Circuit
Model:
Bosch Rexroth Double
Type:
Aluminium gear pump
Pump displacement:
16 cc/rev
Pump Flow @ Governed engine:
34.4 l/min @ rpm
Relief Pressure setting:
17 bar
Pressure Filter Rating- Beta 75 rating:
13 micron
Drive Wheels
Drive Tyre Type:
All Traction Field & Road - 10 ply with inner tube
Drive Tyre size:
18.4 x 26
Drive Wheel rim:
16 x 26, 1 piece
Drive Wheels Tractive Effort:
29.019 kN-machine
Road speed:
10.00 km/hr at governed engine speed
Drive Wheel Inflation Pressure:
1.5 bar
Unladen Ground Pressure Rear:
0.49 bar
Tail Wheel
Tail Wheel Tyre Type:
High Flotation Implement, 10 Ply with inner tube
Tail Wheel Tyre Size:
400 x 15.5
Tail Wheel rim:
13 x 15.5, 1 piece
Tail Wheel Inflation Pressure:
3.0 bar
Unladen Ground Pressure:
1.28 bar
Brakes
Service Brake Type:
Closed Loop Hydrostatic Wheel retardation
Park Brake Type:
Spring applied , hydraulic release wet multi disc
Attachment
Type:
1.5m Class II fork tyne
Capacity:
3.5 tonnes
Hydraulic Tank
Type:
Integral with tubular frame
Oil Type:
Rando HDZ 68 Hydraulic fluid
Capacity:
140 l (150 l for system)
Maximum operating temp:
90 deg C @ 45 ambient
Implement Hyd System
Type:
Fixed displacement open centre seperate gear pumps with full flow suction filtering. WO return filtration or cooling
Suction Filtration:
20 micron
Boom/Mast Hydraulic Function
Pump Model:
Eaton #26
Pump Type:
Gear, open centre, Trans.pump thru-drive
Pump Displacement:
29 cc/rev
Fuel Tank
Type:
Remote to frame, rear mounted
Capacity:
76 L
Non-Boom Aux Hyd Functions
Pump Type:
Gear, open centre, engine geartrain drive
Pump displacement:
22.5 cc/rev
Pump Flow @ Governed engine:
48.4 l/min @ rpm
Electrical System
Voltage:
12V
Lighting:
Frame mounted foward and rear
Lockable Isolater Switch:
Battery mounted fuse, 300 Amp, fall system protection via resetable circuit breakers
Steering System
Type:
Cabin
Front wheel hydraulic skid steer via foot operated treadle control system
Type:
Integral with steel frame, no doors
Guarding:
HD windscreen guard & bonnet guard, rear engine bay doors
Safety/Ergonomics Over-centre lock-down latches x2 to prevent accidental seat plate tip-up; Low profile padded seat with lap strap seat belt; Frame post mounted rearview mirrors
Warning Lights Oil pressure sensor alternator charge light
Operating Mass
Unladen Front:
3,400 kg
Unladen Rear:
2,278 kg
Unladen Total:
5,678 kg
Shortest Wheelbase:
2,568 kg
Load distance ahead of front axle:
1,170 m
Outstretched Tipping load:
5,000 kg
SWL - Payload:
3,500 kg
SWL Laden Front:
8,495 kg
SWL Laden Rear:
683 kg
SWL Laden Total:
9,178 kg
Line Drawings
