Preview only show first 10 pages with watermark. For full document please download

Technical Information - Ea Værktøj Engros A/s

   EMBED


Share

Transcript

T ECHNICAL INFORMATION Model No. Description PRODUCT P 1/ 6 HR2610/ HR2611F/ HR2610T/ HR2611FT Combination Hammers 26mm (1") CONCEPT AND MAIN APPLICATIONS L HR2610 series models are 26mm (1") combination hammers adapted for SDS-PLUS bits, featuring compact and lightweight design, enhanced comfort and better control with ergonomic handle. Model HR2610T/HR2611FT are equipped with quick change drill chuck while Model HR2611/HR2611FT are with AVT; Anti Vibration Technology consisting of Active dynamic vibration absorber with counterweight and Damper spring. AVT ensures operation with extremely low vibration, which is much superior to the competitors. HR2610 series models are available in the variations listed below, including HR2300 and HR2600 series models developed on the same concept. H W (The image above is HR2610/HR2611F.) Dimensions: mm (") Capacity Model Operation Mode AVT LED Chuck type HR2610 HR2610T No No 23mm HR2300 2 modes HR2611F HR2611FT (Rotation only/ No No HR2600 Adapted for Length (L) 361 (14-1/4) 385 (15-1/8) Rotation with hammering) Yes No HR2601 SDS-PLUS shank bits 26mm 77 (3) Width (W) No No HR2610 3 modes 209 (8-1/4) Height (H) Yes Yes HR2611F (Rotation only/ HR2310T 23mm Rotation with hammering/ No No Adapted for *Round shank bits can also be used by No No SDS-PLUS shank bits HR2610T 26mm Hammering only) replacing the factory-mounted chuck with Yes Yes and Round shank bits* Quick change drill chuck (keyless). HR2611FT For information of HR2300 and HR2600 series models, see “TECHNICAL INFORMATION” of each series. Specification Voltage (V) Current (A) Cycle (Hz) 110 120 127 220 230 240 7.7 7 6.6 3.8 3.7 3.5 50/ 60 50/ 60 50/ 60 50/ 60 50/ 60 50/ 60 Specification No load speed: minֿ¹= rpm Impacts per minute= minֿ¹ Model Continuous Rating (W) Input Output 800 400 --400 800 400 800 400 800 400 800 400 HR2610/ HR2611F Max. Output (W) 550 550 550 550 550 550 HR2610T/ HR2611FT Concrete 0 - 1,200 0 - 4,600 Adapted for SDS-PLUS shank bits Adapted for Chuck type and Round shank bits*1 SDS-PLUS shank bits TCT bit 26 (1) Core bit 68 (2-11/16) Capacities: 80 (3-1/8) Diamond core bit mm (") 13 (1/2) Steel 32 (1-1/4) Wood 3 modes Operation mode (Rotation only/ Rotation with hammering/ Hammering only) Vibration absorption No/ Yes (AVT*2) No/ Yes (AVT*2) Yes (by trigger) Variable speed control Yes Rotation reversing facility Torque limiter Yes LED Job light No/ Yes No/ Yes Double insulation Yes Europe, North America: 4.0 (13.1), Australia, Brazil: 2.0 (6.6), Power supply cord: m (ft) Other countries: 2.5 (8.2) Weight according to 2.8/ 2.9 2.9/ 3.0 EPTA-Procedure 01/2003*3: kg (lbs) (6.1/ 6.4) (6.4/ 6.6) *1 Round shank bits can also be used by replacing the factory-mounted chuck with Quick change drill chuck (keyless). *2 AVT (Anti Vibration Technology); Counterweight mechanism + Damper spring *3 with side grip P 2/ 6 Standard equipment Depth gauge .............................................. 1 pc Side grip ................................................... 1 pc Dust cup set ............................................... 1 pc (for some countries only) Quick change drill chuck (keyless) ........... 1 pc (HR2610T/ HR2611FT only) Carrying case ............................................ 1 pc (plastic or aluminum) Note: The standard equipment for the tool shown above may vary by country. Optional accessories SDS-PLUS shank TCT hammer drill bits Taper shank TCT hammer drill bits Taper shank adaptor Cotter Core bits Center bits Core bit adaptor Rod Drill chuck ass'y Chuck adapter assembly Drill chuck S13 Chuck key S13 Tool holder set Scraper assembly Waterproof cover Quick change drill chuck (keyless) Dust cups 5 and 9 Hose Joint 25 Dust cup set Plastic carrying case Hammer grease (30g) Bit grease Depth gauge Blow out bulb Safety goggles Bull points Cold chisels Scaling chisels Grooving chisels Hammer service kit P 3/ 6 Features and benefits [HR2611F, HR2611FT only] Extremely low vibration of 11.5-12.0m/s² achieved by AVT(Anti-Vibration Technology): Counterweight mechanism Counterweight Counterweight mechanism dampens the vibration produced by impact mechanism by moving a counterweight in the opposite direction to the movement of the piston. When the swash bearing moves the piston back and forth, it simultaneously makes the counterweight swing in the opposite direction to the piston in order to counteract the force produced by the movement of the piston. Damper spring absorbs reaction force caused by drill bit at the moment of impact. Compact and Lightweight design Although equipped with AVT: • Features an overall length 9mm shorter than HR2470. • Weighs as light as HR2470 series models. Damper spring Less bit wobbling Easy depth adjustment Increased repairability obtained by making bit guide portion 9mm longer than that of the current models with a single motion. The repairability of clutch cam is drastically increased by simplifying the mechanism of operation mode change. compared with HR2470 series models Depth gauge can be adjusted Quick change drill chuck (keyless) * (HR2610T, HR2611FT only) Easy-to-grip handle ergonomically designed to: • give maximum power thrust. • provide a sure and comfortable grip in any operation; overhead application, drilling with palm-up or palm-down grip. 40 Different bit-angle settings * The bit-angle is adjustable without chisel adapter. High durability * Rubberized soft grip * provides more comfort and control. One-touch sliding chuck * for easy bit changes Single-light LED job light with afterglow function (HR2611F, HR2611FT only) * Torque limiter * illuminates workpiece and drill bit brightly Operation mode change lever positioned on the bottom of gear housing for efficient operation in dark environment. for reduced possibility of breakage *The same advantages as HR2470 series models Redesigned accessories Plastic carrying case Dust cup Easy to transport with large carrying handle Easy to open with large latches Stackable with other plastic carrying cases of the same size or different size Higher visibility of the bit tip obtained by transparent cup mouth Large carrying handle Large latches Connectable with the hose of Makita vacuum cleaner without joint parts • With Makita vacuum cleaner, this dust cup can efficiently extract dust and debris in a wide range of drilling operations; from overhead to vertical downward applications. • Also can be used like the current dust cup by plugging the suction port. Comparison P 4/ 6 of products Performance Comparison Note: 1. The test results depend to a great extent on the hardness of materials, etc. 2. Numbers in the chart below are relative values when the capacities of HR2470 are indexed at 100. (1) Drilling Test conditions: Drilled holes to a depth of 40mm (1-9/16") using ø1.5mm² x 50m cord reel. Test material: Concrete with compressive strength of 40N/mm² [Work speed] [Work speed] [diameter: ø6.5mm (1/4")] slow fast [diameter: ø10.5mm (5/16")] slow fast Makita HR2610 series 100 105 Makita HR2470 series 100 100 BOSCH GBH2-26DRE 90 95 HITACHI DH24PC3 90 90 0 50 100 150 0 [diameter: ø12.5mm( 1/2")] slow fast 50 100 [diameter: ø16.5mm (5/8")] slow fast Makita HR2610 series 105 105 Makita HR2470 series 100 100 BOSCH GBH2-26DRE 110 110 HITACHI DH24PC3 105 90 0 50 100 150 (2) Chipping Test conditions: Chipped concrete with compressive strength of 40N/mm², and measured the amount of concrete removed. [Work speed] Large small Makita HR2610 series 130 Makita HR2470 series 100 BOSCH GBH2-26DRE 130 0 50 100 150 150 0 50 100 150 6.7 24 (15/16) 54 (2-1/8) 65 (2-9/16) 13 (1/2) 32 (1-1/4) 0 - 1,100 0 - 4,500 7.0 26 (1) 68 (2-11/16) 80 (3-1/8) 13 (1/2) 32 (1-1/4) 0 - 1,200 0 - 4,600 Adapted for SDS-PLUS shank bits 2.4 2.9 Diamond core bit Steel Wood No load speed: minֿ¹= rpm Capacities: mm (") 26 (1) 68 (2-11/16) N/A 800 No 15.5 90 Yes Yes No/ Yes 370 (14-1/2) 84 (3-1/4) 214 (8-3/8) No/ Yes (AVT*3) 15.5/ 12.0 91/ 90 Yes Yes No/ Yes 361 (14-1/4) 77 (3) 209 (8-1/4) 204 (8) 360 (14-1/8) 80 (3-1/8) 15.5 86 Yes/ No/ No Yes/ Yes/ No Yes (F-model only)/ No/ No 3 modes (R/ R+H/ H) 3 modes (R/ R+H/ H) 210 (8-1/4) 380 (15) 84 (3-5/16) 15.0 (18.5*2) 91 (92*2) Yes/ No Yes No 65 (2-9/16) 80 (3-1/8) 13 (1/2) 13 (1/2) 32 (1-1/4) 30 (1-3/16) 0 - 900 0 - 1,100/ 0 - 1,100/ 1,100 0 - 4,000 0 - 4,500/ 0 - 4,500/ 4,500 Adapted for SDS-PLUS shank bits 2.5*2 2.3 2.7 3.0 24 (15/16) 54 (2-1/8) 6.7 780 HR2450(F)/ HR2451/ HR2452 GBH2-26DRE/ GBH2-26DE BOSCH 198 (7-3/4) 351 (13-3/4) 73 (2-7/8) 12.7 (20.0*2) 92 (91*2) Yes Yes No unknown 3.2 0 - 4,600 65 (2-9/16) 13 (1/2) 32 (1-1/4) 0 - 1,150 24 (15/16) 50 (2) 7.0 800 DH24PC3 HITACHI 5.0 (16.4) 4.0 (13.1) 4.0 (13.1)*4 4.0 (13.1) Power supply cord: m (ft) 4.0 (13.1) 2.8 2.7 Weight according to EPTA2.9 2.9 2.8/ 2.9 (6.2) (6.0) Procedure 01/2003*5: kg(lbs) (6.4) (6.4) (6.1/ 6.4) *1 Measured according to our conventional reference, *2 Actually measured value, *3 AVT (Anti Vibration Technology); Counterweight mechanism + Damper spring *4 Europe, North America: 4.0 (13.1), Australia, Brazil: 2.0 (6.6), Other countries: 2.5 (8.2), *5 with side grip Vibration absorption Vibration: m/s² Noise: dB(A) Rotation reversing facility Variable speed control LED Job light Length Dimensions: Width mm (") Height R= Rotation only R+H= Rotation with Hammering H= Hammering only Impact energy (EPTA): J Impact energy*1: J Operation mode: Chuck type Impacts per minute= minֿ¹ 2.4 2.7 780 800 Continuous rating input: W Rated amperage for North America: A TCT bit Core bit Concrete Specification HR2470/ HR2470F Makita HR2610/ HR2611F Model Specification Comparison Comparison of products P 5/ 6 Specification Continuous rating input: W Rated amperage for North America: A TCT bit Core bit Diamond core bit Steel Wood No load speed: minֿ¹= rpm Impacts per minute= minֿ¹ Model Capacities: mm (") 24 (15/16) 54 (2-1/8) 65 (2-9/16) 13 (1/2) 32 (1-1/4) 0 - 1,100 0 - 4,500 26 (1) 68 (2-11/16) 80 (3-1/8) 13 (1/2) 32 (1-1/4) 0 - 1,200 0 - 4,600 Adapted for SDS-PLUS shank bits and Round shank bits*1 2.4 2.9 15.5 90 Yes Yes No/ Yes 394 (15-1/2) 431 (17) 84 (3-1/4) 214 (8-3/8) 4.0 (13.1) 3.0 (6.7) 15.5 86 Yes Yes No/ Yes 384 (15-1/8) 421 (16-1/2) 80 (3-1/8) 204 (8) 4.0 (13.1) 2.9 (6.5) Yes No 15.0 91 Yes Yes No 407 (16) 433 (17) 84 (3-5/16) 210 (8-1/4) 4.0 (13.1) 3.0 (6.7) Yes No/ Yes (AVT*3) 15.0/ 11.5 91/ 90 Yes Yes No/ Yes 385 (15-1/8) 422 (16-5/8) 77 (3) 209 (8-1/4) 4.0 (13.1)*6 2.9/ 3.0 (6.4/ 6.6) 2.5*4 3.0 Adapted for SDS-PLUS shank bits and Round shank bits*1 26 (1) 68 (2-11/16) 80 (3-1/8) 13 (1/2) 30 (1-3/16) 0 - 900 0 - 4,000 N/A 3 modes (R/ R+H/ H) 2.1 2.7 24 (15/16) 54 (2-1/8) 65 (2-9/16) 13 (1/2) 32 (1-1/4) 0 - 1,100 0 - 4,500 6.7 GBH2-26DFR 800 BOSCH 3 modes (R/ R+H/ H) 2.4 2.7 6.7 7.0 HR2470T/ HR2470FT HR2450T/ HR2450FT 780 780 Makita unknown 10.2 90 Yes Yes No 384 (15-1/8) N/A 73 (2-7/8) 198 (7-3/4) 5.0 (16.4) unknown 3.2 24 (15/16) 50 (2) 65 (2-9/16) 13 (1/2) 32 (1-1/4) 0 - 1,150 0 - 4,600 7.0 DH24PM 800 HITACHI 10.0 (14.0*4) 89 (88*4) Yes Yes No 352 (13-7/8) N/A 89 (3-1/2) 203 (8) 4.0 (13.1) 3.0 (6.5) 2 modes (R/ R+H) unknown 1.8 22 (7/8) unknown unknown 13 (1/2) 20 (13/16) 0 - 1,200/ 0 - 2,500 0 - 4,600 unknown TE2-M 650 HILTI *1 Round shank bits can also be used by replacing the factory-mounted chuck with Quick change drill chuck (keyless), *2 Measured according to our conventional reference, *3 AVT (Anti Vibration Technology); Counterweight mechanism + Damper spring, *4 Actually measured value, *5 with Quick change drill chuck, *6 Europe, North America: 4.0 (13.1), Australia, Brazil: 2.0 (6.6), Other countries: 2.5 (8.2), *7 with side grip Quick change drill chuck Vibration absorption Vibration: m/s² Noise: dB(A) Rotation reversing facility Variable speed control LED Job light Length Dimensions: Length*5 mm (") Width Height Power supply cord: m (ft) Weight according to EPTAProcedure 01/2003*7: kg(lbs) R= Rotation only R+H= Rotation with Hammering H= Hammering only Impact energy (EPTA): J Impact energy*2: J Operation mode: Chuck type Concrete HR2610T/ HR2611FT 800 Specification Comparison Comparison of products P 6/ 6