Technical Reference Guide

Transcript

Stylistic® ST5100 Series Tablet PC Technical Reference Guide Copyright and Trademark Information Fujitsu Computer Systems Corporation has made every effort to ensure the accuracy and completeness of this document. Because ongoing development efforts are made to continually improve the capabilities of our products, however, the data contained herein represents Fujitsu design objectives and is provided for comparative purposes; actual results may vary based on a variety of factors. This product data does not constitute a warranty. Specifications are subject to change without knowledge. Fujitsu and the Fujitsu logo are registered trademarks of Fujitsu Limited. Stylistic is a registered trademark of Fujitsu Computer Systems Corporation. Softex and OmniPass are trademarks or registered trademarks of Softex, Inc. IBM is a registered trademark of IBM Corporation. PCMCIA and CardBus are registered trademarks of the Personal Computer Memory Card International Association. Intel and Core are trademarks or registered trademarks of Intel Corporation. Microsoft and Windows are registered trademarks of Microsoft Corporation. All other products are trademarks or registered trademarks of their respective companies. Warning Handling the cord on this product will expose you to lead, a chemical known to the State of California to cause birth defects or other reproductive harm. Wash hands after handling. • Installing or removing a Memory Stick or SD Card during your Tablet PC’s shutdown or bootup process may damage the card and/or your computer. • Do not insert a card into a slot if there is water or any other substance on the card as you may permanently damage the card, your Tablet PC, or both. Copyright 2006 - Fujitsu Computer Systems Corporation. All rights reserved. No part of this publication may be copied, reproduced, or translated, without the prior written consent of Fujitsu Computer Systems Corporation. No part of this publication may be stored or transmitted in any electronic form without the prior consent of Fujitsu Computer Systems Corporation. FPC58-1595-01 DECLARATION OF CONFORMITY according to FCC Part 15 Responsible Party Name: Address: Telephone: Declares that product: Fujitsu Computer Systems Corporation 1250 E. Arques Avenue, Sunnyvale, CA 94085 408-746-6000 Model: Stylistic ST5100 Series Tablet PC Complies with Part 15 of the FCC Rules This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and, (2) This device must accept any interference received, including interference that may cause undesired operation. For more detailed information about the FCC rules and their applicability to the Stylistic ST5100 Series Tablet PC, refer to “Agency Notices” on page 68 of this document. IMPORTANT SAFETY INSTRUCTIONS ■ For Authorized Repair Technicians Only This unit requires an AC adapter to operate. Use only UL Listed Class 2 Adapters with an output rating of 16 VDC, with a current of 3.75A minimum. AC Adapter output polarity: Danger of explosion if Lithium (clock) battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer’s instruction. + ■ When using your notebook equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury to persons, including the following: ■ Do not use this product near water for example, near a bathtub, washbowl, kitchen sink or laundry tub, in a wet basement or near a swimming pool. ■ Avoid using the modem during an electrical storm. There may be a remote risk of electric shock from lightning. ■ Do not use the modem to report a gas leak in the vicinity of the leak. ■ Use only the power cord and batteries indicated in this manual. Do not dispose of batteries in a fire. They may explode. Check with local codes for possible special disposal instructions. ■ To reduce the risk of fire, use only No. 26 AWG or larger UL Listed or CSA Certified Telecommunication Line Cord ■ For TV Tuner Models: To protect from overvoltages and transients on the Cable Distribution System, make sure that the outer shield of the coaxial cable is connected to earth (grounded) at the building premises as close to the point of cable entrance as practicable, as required per NEC Article 820.93, ANSI/NFPA 70: 2005. If you have questions about your CATV installation, contact your service provider. SAVE THESE INSTRUCTIONS For continued protection against risk of fire, replace only with the same type and rating fuse. System Disposal LAMP(S) INSIDE THIS PRODUCT Hg CONTAIN MERCURY AND MUST BE RECYCLED OR DISPOSED OF ACCORDING TO LOCAL, STATE, OR FEDERAL LAWS. Table of Contents Copyright and Trademark Information ......................................................................................... About This Guide .............................................................................................................................. 2 1 Organization....................................................................................................................................................... Related Documentation...................................................................................................................................... 1 2 Chapter 1 Stylistic ST5100 Tablet PC Features ............................................................................................... 3 Hardware Features ............................................................................................................................................. PC Card Support .................................................................................................................................... Internal Modem...................................................................................................................................... Internal LAN.......................................................................................................................................... ACPI Support......................................................................................................................................... DMI Support .......................................................................................................................................... USB 2.0 Support .................................................................................................................................... Smart Card Support ............................................................................................................................... SD Card/Memory Stick Support............................................................................................................ Infrared Support..................................................................................................................................... IEEE 1394 Support ................................................................................................................................ Software Features .............................................................................................................................................. Supported Operating Systems................................................................................................................ Pen Support............................................................................................................................................ Fujitsu Menu .......................................................................................................................................... 3 3 3 3 4 4 4 4 4 4 4 4 4 5 5 Chapter 2 Configuring the Stylistic ST5100 Tablet PC BIOS ........................................................................ 6 Permanent and Current BIOS Settings .............................................................................................................. BIOS Setup Utility............................................................................................................................................. Starting BIOS Setup............................................................................................................................... Using BIOS Setup.................................................................................................................................. Exiting BIOS Setup ............................................................................................................................... BIOS Setup Main Menu Options........................................................................................................... Drive0 Submenu Options....................................................................................................................... Advanced Menu Options ....................................................................................................................... IrDA Port Configuration Submenu Options .......................................................................................... Keyboard Features Submenu Options ................................................................................................... Video Submenu Options........................................................................................................................ Internal Device Configurations Submenu.............................................................................................. CPU Features Submenu ......................................................................................................................... USB Features Submenu ......................................................................................................................... Miscellaneous Configurations Submenu ............................................................................................... Event Logging Submenu ....................................................................................................................... Security Menu Options .......................................................................................................................... Hard Disk Security Submenu ................................................................................................................ Owner Information Submenu ................................................................................................................ Security Chip Setting Submenu............................................................................................................. Boot Menu Options................................................................................................................................ Boot Device Priority Submenu .............................................................................................................. Info Menu .............................................................................................................................................. Exit Menu Options................................................................................................................................. 6 6 6 7 8 9 10 11 12 13 14 15 16 18 19 20 21 23 24 25 26 27 28 29 Chapter 3 Hardware Specifications .................................................................................................................. 30 General Specifications ....................................................................................................................................... Digitizer Specifications...................................................................................................................................... External Video Capabilities ............................................................................................................................... Display Specifications ....................................................................................................................................... Environmental Specifications ............................................................................................................................ Peripheral Interface Specifications .................................................................................................................... Physical Specifications ...................................................................................................................................... Power System Specifications............................................................................................................................. Internal Modem Specifications.......................................................................................................................... Internal LAN Specifications .............................................................................................................................. Agency Approval Specifications ....................................................................................................................... Tablet Dock Specifications................................................................................................................................ 30 31 31 32 32 33 33 34 35 35 36 36 Chapter 4 Peripheral Interfaces ........................................................................................................................ 37 DC Power Input ................................................................................................................................................ Universal Serial Bus Port................................................................................................................................... IrDA Port ........................................................................................................................................................... Tablet Dock Interface Port................................................................................................................................. Audio Jacks........................................................................................................................................................ PC Card Port ...................................................................................................................................................... Hard Drive Port.................................................................................................................................................. RJ-45 LAN Port ................................................................................................................................................. IEEE 1394 Port .................................................................................................................................................. 37 38 38 39 43 44 46 47 47 Chapter 5 System Power .................................................................................................................................... 49 System Power Hardware.................................................................................................................................... Battery Pack........................................................................................................................................... DC Power Inputs.................................................................................................................................... 49 49 50 Chapter 6 Installing Hardware Options ........................................................................................................... 51 Installing/Removing a DIMM Module .............................................................................................................. Installing a Memory Module ................................................................................................................. Removing a Memory Module................................................................................................................ Replacing/Installing a Wireless LAN Module.................................................................................................. Removing a Wireless LAN Module ...................................................................................................... Installing a Wireless LAN Module....................................................................................................... Replacing the IDE Hard Drive........................................................................................................................... Removing the Hard Drive...................................................................................................................... Installing the Hard Drive ....................................................................................................................... 51 51 52 53 53 54 54 54 54 AT Command Set ............................................................................................................................. 55 AT Commands Table......................................................................................................................................... AT Data Commands .............................................................................................................................. AT Fax (Class1) Commands.................................................................................................................. V.25ter AT Commands.......................................................................................................................... S Register Table................................................................................................................................................. Result Codes Summary...................................................................................................................................... 56 56 61 62 63 66 Agency Notices .................................................................................................................................. 68 Wireless LAN Agency Notices.......................................................................................................................... 70 About This Guide This guide provides technical information on the Fujitsu Stylistic ST5100 Tablet PC for technicians, hardware developers, and software developers. Organization 0 This guide is organized as follows: • Chapter 1: Tablet PC Features This chapter discusses some of the system’s main features and technology. • Chapter 2: Configuring the Stylistic ST5100 Tablet PC BIOS This chapter provides details on using BIOS Setup Utility for the Stylistic ST5100 Tablet PC. BIOS configuration options are explained in detail. • Chapter 3: Hardware Specifications This chapter gives hardware specifications on the Tablet PC system. Industry standards supported by the Stylistic ST5100 Tablet PC are listed. • Chapter 4: Peripheral Interfaces This chapter provides details on peripheral interfaces provided by the Stylistic ST5100 Tablet PC and the Stylistic ST5100 Tablet Dock. • Chapter 5: System Power This chapter provides information on the Tablet PC’s system power hardware. • Chapter 6: Installing Hardware Options This chapter gives detailed instructions on installing hardware options such as PCMCIA, DIMM, and WLAN cards, as well as the IDE Hard Drive. • Appendix A: AT Command Set This appendix provides a detailed list of AT commands used by the Tablet PC’s modem, including AT Commands, S Register Table, and Result Codes Summary information. • Appendix B: Agency Notices This appendix states notices required by regulatory agencies in the United States and Canada that apply to the Stylistic ST5100. 1 Related Documentation 0 Documentation relating to the Stylistic ST5100 Tablet PC is listed below. Refer to these documents for details on topics not covered in this guide. Stylistic ST5100 User’s Guide This guide provides an introduction to the Stylistic ST5100 Tablet PC’s basic functions for the end user. Stylistic ST5100 Tablet Dock User’s Guide This guide gives instructions on using the Stylistic ST5100 Tablet Dock. The following documents, available from retail booksellers, contain additional information about software preinstalled on the Stylistic ST5100 Tablet PC. Microsoft Windows XP Professional Resource Kit (ISBN: 0-7356-1974-3) This manual is a technical guide for installing, configuring, and supporting Windows XP and is published by Microsoft Press, 1-800-MSPRESS in the U.S. as well as from retail book sellers. The following resources contain information on software development tools for Windows: Microsoft Developer’s Network The Microsoft Developer’s Network web site provides links to information on application programming interfaces (APIs) used with Microsoft Windows. The site address is . The following documents provide information on industry standards supported by the Stylistic ST5100 Tablet PC. Advanced Configuration and Power Interface (ACPI) Specification The ACPI specification was developed by Microsoft, Intel, and Toshiba to manage device control in order to conserve power. The specification and additional detailed information is available at the ACPI web site, www.acpi.info. PC Card Standards The Stylistic ST5100 Tablet PC and supporting system software comply with PCMCIA and PC Card standards specifications up to and including the PC Card Standard February 1995 (also referred to as PC Card Standard Release 3.0 in this document and other related documentation). PC Card standards are published by: Personal Computer Memory Card International Association, 2635 North First Street, Suite 209, San Jose, CA 95134, , (408) 433-CARD (2273). IrDA Standards The IrDA port on the Stylistic ST5100 Tablet PC is compliant with IrDA (Infrared Data Association) Standard Version 1.1 published by: Infrared Data Association, . Universal Serial Bus Specification The Universal Serial Bus (USB) ports on the Stylistic ST5100 Tablet PC and docking peripherals are compliant with the Universal Serial Bus Specification Version 2.0. Refer to this specification for USB details including: cable requirements, topology, and USB power distribution. This specification and other technical documents regarding USB are available on the Universal Serial Bus Implementer’s Forum home page at . Related Documentation 2 Chapter 1 Stylistic ST5100 Tablet PC Features This chapter provides an introduction to the Stylistic ST5100 Tablet PC system hardware and software and gives an overview of some of the Tablet PC’s features. Detailed specifications on the features discussed in this chapter are given in other chapters of this guide. The Stylistic ST5100 computer series is designed for the Microsoft Windows XP Tablet PC Edition. The system uses an active digitizer and conforms to the Windows Tablet PC standards. The Stylistic ST5100 Tablet PC system has been tested by Windows Hardware Quality Labs (WHQL) at Microsoft Corporation and is compliant with PC2001 system design guidelines. Hardware Features 1 PC Card Support 1 The Stylistic ST5100 Tablet PC is equipped with a PC Card slot that allows you to install a Type I or II PC Card. The PC Card slot is compliant with PC CardBus Standard Release 3.0 and provides support for the following PC Card features: • Multivoltage 3.3/5 V PC Cards (detected automatically) • CardBus (PCI bridge) type PC Cards • Supports PCIC (PC Card I/O Card) protocol • Backward compatibility with previous PC Card Standard Release level PC Cards Among the types of PC Cards supported by this slot are: • Wireless LAN cards • Bluetooth cards • ISDN cards • Communications cards • LAN cards • SCSI cards Internal Modem 1 The Stylistic ST5100 Tablet PCs are equipped with an internal 56 Kbps* modem. * The 56 Kbps rate is nominal; due to FCC restrictions, actual rates are limited to 53 Kbps. For details on the built-in modem, see “Internal Modem Specifications” on page 35. Internal LAN 1 The Stylistic ST5100 Tablet PCs are equipped with an internal wired 10/100/1000* Base-T/Tx Ethernet LAN. *1000 Mbps, commonly referred to as Gigabit Ethernet. 3 ACPI Support 1 The Stylistic ST5100 Tablet PC supports the Advanced Configuration and Power Interface (ACPI) Specification in all system configurations. With ACPI, power management features are controlled and configured primarily by the BIOS and BIOS settings. The ACPI specifications allow for additional control over power management features such as state transitions and device timeouts. Refer to the ACPI specifications and the documentation for your operating system regarding power management with ACPI. DMI Support 1 The Stylistic ST5100 supports the Desktop Management Interface (DMI). DMI provides a framework for managing the variety of components within the Tablet PC. The Event Logging menu in the BIOS allows you to configure the DMI event logging options (see “Event Logging Submenu” on page 20). USB 2.0 Support 1 The Universal Serial Bus (USB) 2.0 design is the primary interface for your tablet PC. The Stylistic ST5100 USB ports are compliant with Universal Serial Bus Specification 2.0, and are backward-compatible with USB 1.1 devices. For more information on the USB interface, refer to “Universal Serial Bus Port” on page 38. Smart Card Support 1 The dedicated Smart Card slot allows you to insert a Smart Card, on which you can store information such as medical records or electronic “cash”. SD Card/Memory Stick Support 1 The Secure Digital (SD)/Memory Stick (MS) card slot allows you to install a flash memory card for data storage. Infrared Support 1 There are three infrared ports on your Stylistic ST5100 Tablet PC, two infrared keyboard/mouse ports and an IrDA/ FIR port. The keyboard/mouse ports are used for receiving communications from an infrared keyboard or mouse. (Note that the infrared keyboard/mouse ports are receive-only, one-direction serial ports.) The IrDA/FIR port is used for communications compliant with IrDA Standard Revision 1.1. IEEE 1394 Support 1 The Institute of Electrical and Electronics Engineers, Inc. (IEEE) standard 1394 architecture supports a fast external bus that allows transfer rates of up to 400 Mbps. IEEE 1394 (also known as “Firewire” or “iLink” by other vendors) allows connection of the tablet PC with peripherals such as digital video cameras, providing for fast transfer of the large files. For more information on the IEEE 1394 port, refer to “IEEE 1394 Port” on page 47. Software Features 1 Supported Operating Systems 1 The Stylistic ST5100 Tablet PC is distributed with Microsoft Windows XP Tablet PC Edition 2005 pre-installed. Licensing and user documentation for the operating system installed on your system is also included with the Tablet PC. For details on the operating system, refer to the documentation provided, or refer to the documents listed in “Related Documentation” in the About This Manual section of this guide. Note: MS-DOS is not supported as an end-user operating environment. Support for MS-DOS is limited to the use of configuration and other support utilities designed for the Stylistic ST5100 system. Software Features 4 Pen Support 1 The Stylistic ST5100 Tablet PC has an active digitizer and employs the Microsoft Windows XP for Tablet PC as its operating system. As such, the on-screen keyboard, handwriting recognition, and pen utilities are part of the tablet PC operating system. There are three ways to access the pen utilities: • Double-click on the “Change tablet and pen settings” icon in the system tray in the lower right of the screen, • Select Start -> Control Panel -> Tablet and Pen Settings, or, • Click on the Fujitsu Menu icon in the system tray (or press the [Fn] button twice in quick succession), and select Tablet and Pen Settings from the menu. To display the on-screen keyboard: • Click the Tablet PC Input Panel icon adjacent to the Start button, or, • Click on the Fujitsu Menu icon in the system tray (or press the [Fn] button twice in quick succession), and select Tablet PC Keyboard from the menu. To access the Pen Configuration applet (developed by Fujitsu), click Start -> Control Panel -> Fujitsu Pen Settings. Fujitsu Menu 1 The Fujitsu Menu provides a handy list of shortcuts to commonly-used utilities. To open the Fujitsu Menu, click on the Fujitsu Menu icon in the system tray at the bottom right of the screen or press the [Fn] button twice in quick succession. The following utilities can be accessed directly from the Fujitsu Menu: • Control Panel • Tablet PC Keyboard • Tablet and Pen Settings • Fujitsu Display Controls • Brightness Control • Sounds and Audio Devices • Capture Screen • Capture Window • Organize Favorites • Power Options • Printers and Faxes • LCD Brightness Min. • LCD Brightness Max. • Enable/Disable Button Panel • Fujitsu Menu Settings Any of these utilities can be added or deleted from the Fujitsu Menu by clicking on the Fujitsu Menu Settings button and checking or unchecking the utility then applying your changes. Additionally, any new applications can be added to the menu by clicking Fujitsu Menu Settings ->, then browsing to the application you want to add. Software Features 5 Chapter 2 Configuring the Stylistic ST5100 Tablet PC BIOS This chapter provides instructions on how to use the Setup Utility to configure the Stylistic ST5100 Tablet PC BIOS. Permanent and Current BIOS Settings 2 Some BIOS configuration utilities allow you to select permanent and/or current settings when configuring BIOS options. When you change a permanent setting, BIOS parameters stored in CMOS memory are changed and the new setting is applied after the system is restarted. When you change a current setting, BIOS parameters stored in dynamic memory are changed and the new setting is applied for the current session. Also, note that a change to the current setting only remains in effect until the system is restarted or shut down. BIOS data resides in the system’s CMOS memory. When the system is powered on, BIOS data is copied or “shadowed” into the system’s dynamic memory and the system runs using BIOS parameters stored in dynamic memory. BIOS Setup Utility 2 The BIOS Setup Utility is a configuration utility that you can use to change your system’s permanent BIOS settings. The BIOS Setup Utility application is stored in the BIOS flash ROM. (BIOS Setup values or settings are stored in CMOS memory.) Instructions for starting and running BIOS Setup are given in the following discussions. Starting BIOS Setup 2 To start BIOS Setup, restart your system and when the message “Tap, Click, or Enter for System Utilities” is displayed in the status bar at the bottom of the screen, tap anywhere on the screen with your tablet pen. Select “BIOS Setup” from the pop-up menu that appears. You can also press the [Alt] button (the button closest to the corner of the display), or press [F2] on an external keyboard to launch BIOS Setup. The system starts the BIOS Setup Utility and the BIOS Setup Main menu is displayed. Options and settings for menus in BIOS Setup are described in tables appearing later in this chapter. Permanent and Current BIOS Settings 6 Using BIOS Setup 2 Once the BIOS Setup Utility is started, you can use BIOS Setup to change your system BIOS settings. The BIOS Setup screen consists of a menu bar, menu items, a command bar, and a window for item-specific help as shown below. BIOS Configuration Options Menu Bar BIOS Configuration Settings Main Advanced PhoenixBIOS Setup Utility Security Boot Info Item-Specific Help Window Exit Item Specific Help [02:34:56] [10/18/2006] Drive0 [FUJITSU MHV2060BH-(PM)] Language: [English (US)] Command Bar F1 Help ESC Exit Select Item Select Menu Adjust calendar clock. , , or selects field. - Change Values Space Enter Select Sub-Menu F9 Setup Defaults F10 Save and Exit ▲ (Triangle symbol indicates that a submenu is available) ▲ System Time: System Date: Highlighted text indicates equivalent keyboard command Figure 2-1 BIOS Setup Screen Instructions for selecting and changing BIOS options and navigating BIOS Setup menus: If you want to... Do one of these... Select a BIOS Setup menu from the menu bar To move left and right to highlight the menu and display a list of menu options, do one of the following: • • • • Select a BIOS option Press either side of the lower navigation button (the one that is farthest from the application buttons) Tap on the menu name in the menu bar Tap on the right or left side of the Select Menu field in the command bar Use the right or left arrow keys on an external keyboard To highlight an option in the list of items for a given menu, do one of the following: • • • • Press either side of the upper navigation button (the one that is closest to the application buttons) Tap on the setting field for the option Tap on the right or left side of the Select Item field in the Command Bar Use the up and down arrow keys on an external keyboard BIOS Setup Utility 7 If you want to... Change the setting of a selected BIOS option Do one of these... To cycle through the list of possible settings, do one of the following: • • • • Tap directly on the setting field Tap on the highlighted commands to the right or left of Change Values in the command bar Use the -, +, and space keys on an external keyboard Press the Display Orientation button (third button from the right) Access a pop-up menu with a list all possible settings for a given BIOS option Tap on the [option], then press the [Ent] application button. Tap on the setting of your choice to select it. You can also hold the pen barrel button while tapping to bring up the pop-up menu. Select and enter a submenu To select and enter a submenu, do one of the following: • Tap on the submenu name, then tap again to activate it. • Select the submenu using the up and down arrow keys on an external keyboard and press Enter, or press the [Ent] application button. View Item-Specific Help for a BIOS option View General Help for BIOS Setup Exit BIOS Setup Load factory default settings for all BIOS options Select the option. Item-specific help is displayed in the Item Specific Help panel on the right-hand side of the screen. Tap on Help in the command bar or press F1 on your external keyboard. The BIOS Setup help screen is displayed giving general instructions for using BIOS Setup To exit the BIOS Setup Utility, do one of the following: • Choose the appropriate option from the Exit menu • Tap Save and Exit in the command bar • Press F10 on an external keyboard. To load the factory BIOS default settings, do one of the following: • Press F9 on an external keyboard • Select Setup Defaults from the command bar • Select Load Setup Defaults from the Exit menu Exiting BIOS Setup 2 Once you have finished making changes in BIOS Setup, you must exit BIOS Setup and allow the system to boot to apply your configuration changes. You can exit BIOS Setup by selecting options in the Exit menu. The Exit menu includes options that allow you to load default BIOS settings, load previous settings, discard your changes, save your changes, and exit BIOS Setup. For details on Exit menu options, see “Exit Menu Options” on page 29. BIOS Setup Utility 8 BIOS Setup Main Menu Options 2 BIOS Setup Main menu options are given in Table 2-1. (Options and settings for other BIOS Setup menus are described in the tables that follow.) The default setting for each option is listed in bold type when applicable. Main Advanced PhoenixBIOS Setup Utility Security Boot Info Exit Item Specific Help ▲ System Time: System Date: [02:34:56] [10/18/2006] Drive0 [FUJITSU MHV2060BH-(PM)] Language: [English (US)] Select Item Select Menu , , or selects field. - Change Values Space Enter Select Sub-Menu ▲ F1 Help ESC Exit Adjust calendar clock. F9 Setup Defaults F10 Save and Exit Table 2-1. BIOS Setup Main Menu Options Menu Field Options Default Description System Time 00:00:00 to 23:59:59 ___ Real Time Clock (RTC) setting in hours, minutes, and seconds. Note that the system time option uses a 24 hour format. System Date 01/01/1980 to 12/31/ 2099 ___ RTC calendar setting in month/day/year format. Drive0 Submenu ___ ___ Select this field to access the primary disk drive submenu. (See “Drive0 Options” later in this section.) Language • English • Japanese [English] Select the display language for the BIOS. BIOS Setup Utility 9 Drive0 Submenu Options 2 Options and settings for the Drive0 Submenu are given in Table 2-2. PhoenixBIOS Setup Utility Exit Submenu Item Specific Help Drive0 [FUJITSU MHV2060BH PL] Type: [Auto] LBA Format Total Sectors: 117210240 Maximum Capacity: 60012MB Select Serial ATA/IDE drive installed here. [Auto] The BIOS auto-types the drive on boot time. [None] The drive is disabled. Select Item Select Menu - Change Values Space Enter Select Sub-Menu ▲ F1 Help ESC Exit F9 Setup Defaults F10 Save and Exit Table 2-2. the Primary Master Submenu of the Main Menu Menu Field Options Default Description Type: • Auto • None [Auto] Selects the Serial ATA/IDE device type. Select Auto to have the type automatically identified by the BIOS at POST. If None is selected, all of the following Set-up items do not appear. LBA Format Logical Block Addressing (LBA) Total Sectors: --- --- The total number of sectors on your hard disk Maximum Capacity: --- --- The maximum capacity of your hard disk BIOS Setup Utility 10 Advanced Menu Options 2 Options in the Advanced menu are described in Table 2-3. Main Advanced PhoenixBIOS Setup Utility Security Boot Info Exit Item Specific Help ▲ ▲ ▲ ▲ ▲ ▲▲ IrDA Port Configurations Keyboard Features Video Features Internal Device Configurations CPU Features USB Features Miscellaneous Configurations ▲ Event Logging Select Item Select Menu - Change Values Space Enter Select Sub-Menu ▲ F1 Help ESC Exit Configures IrDA ports. F9 Setup Defaults F10 Save and Exit Table 2-3. BIOS Setup Advanced Menu Options Option Description IrDA Port Configurations Submenu Enter this submenu to configure the infrared port features. (See “IrDA Port Configuration Submenu Options” on page 12 for details.) Keyboard Features Submenu Enter this submenu to configure the system keyboard. (See “Keyboard Features Submenu Options” on page 13 for details). Video Features Submenu Enter this submenu to select system resources for the video controller. (See “Video Features Submenu Options” on page 14 for details.) Internal Device Configurations Submenu Enter this menu to configure additional device controllers. (See “Internal Device Configurations Submenu Options” on page 15 for details.) CPU Features Submenu Enter this submenu to change CPU features. (See “CPU Features Submenu Options” on page 16 for details). USB Features Submenu Enter this submenu to change USB features. (See “USB Features Submenu Options” on page 18 for details). Miscellaneous Configurations Submenu Enter this submenu to change several miscellaneous features, such as Wake Up On LAN. (See “Miscellaneous Configurations Submenu Options” on page 19 for details). Event Logging Submenu Enter this submenu to view the Event Log features. (See “Event Logging Submenu Options” on page 20 for details). BIOS Setup Utility 11 IrDA Port Configuration Submenu Options 2 Configuration options for the IrDA Port Configuration submenu are given in Table 2-4. PhoenixBIOS Setup Utility Exit Submenu Item Specific Help IrDA Port Configurations Infrared Port: Mode: I/O Address: Interrupt: DMA Channel: [Enabled] [FIR] [2E8-2EF] [IRQ 6] [DMA 3] [Disabled] The port is disabled. [Enabled] The port is enabled with user configuration. [Auto] Plug & Play OS configure the port. Select Item Select Menu - Change Values Space Enter Select Sub-Menu ▲ F1 Help ESC Exit F9 Setup Defaults F10 Save and Exit Table 2-4. IrDA Port Configurations Submenu Menu Field Options Default Description Infrared Port: • Disabled • Enabled • Auto [Enabled] Determines whether the infrared port is active and the method used to configure the infrared port. • Select [Auto] to allow the BIOS or operating system to configure the port automatically. • Select [Enabled] to configure the I/O Address and Interrupt options manually in BIOS setup. • Select [Disabled] to turn off the infrared port. Mode: • IrDA • FIR [FIR] Determines which physical interface the infrared port is assigned to. Select IrDA to use the IrDA port in Standard IR (SIR) mode (115 Kbps). Select FIR to use the IrDA port in Fast IR mode (4 Mbps). Note: The Infrared port option must be Enabled before this setting can be changed. I/O Address • • • • 3F8 - 3FF 2F8 - 2FF 3E8 - 3EF 2E8 - 2EF [2E8 - 2EF] Determines the base I/O address and interrupt request level used for the infrared port. The Infrared Port option must be set to [Enabled] before this setting can be changed. Interrupt: • • • • IRQ 3 IRQ 6 IRQ 10 IRQ 11 [IRQ 6] Determines the interrupt number for the infrared port. Note: The Infrared port option must be Enabled before this setting can be changed. DMA Channel • DMA 1 • DMA 3 [DMA 3] Determines the DMA channel assigned to the infrared port when using Fast IR mode. This option is only selectable when the Infrared Port Mode setting is FIR. BIOS Setup Utility 12 Keyboard Features Submenu Options 2 Configuration options for the Keyboard Features submenu are given in Table 2-5. PhoenixBIOS Setup Utility Exit Submenu Item Specific Help Keyboard Features Numlock: Select power-on state for Numlock. Select Item Select Menu - Change Values Space Enter Select Sub-Menu ▲ F1 Help ESC Exit [Off] F9 Setup Defaults F10 Save and Exit Table 2-5. Keyboard Features Submenu Options Menu Field Options Numlock • On • Off Default [Off] Description This option determines the state of the NumLock key when the system is powered on. BIOS Setup Utility 13 Video Submenu Options 2 Options for the Video Features submenu are given in Table 2-6. PhoenixBIOS Setup Utility Exit Submenu Item Specific Help Video Features Display: [Auto]] Select display terminal. * This setting is not effective after operating system starts up. Select Item Select Menu - Change Values Space Enter Select Sub-Menu ▲ F1 Help ESC Exit F9 Setup Defaults F10 Save and Exit Table 2-6. Video Features Submenu Options Menu Field Options Default Description Display: • Internal Flat Panel • External • Auto [Auto] Selects where the video signal will be routed. Note that once the system boots up, the settings for the Windows video driver take precedence over this setting. BIOS Setup Utility 14 Internal Device Configurations Submenu 2 Options for the Internal Device Configurations submenu are given in Table 2-7. PhoenixBIOS Setup Utility Exit Submenu Internal Device Configurations Serial ATA Controller: SATA Controller Mode Option: AHCI Configuration: Bluetooth(R): LAN Controller: Wireless LAN: IEEE1394 Controller: Select Item Select Menu [Disabled] Serial ATA port is disabled. [Enabled] Serial ATA port is enabled. - Change Values Space F9 Setup Defaults Enter Select Sub-Menu F10 Save and Exit ▲ F1 Help ESC Exit [Enabled] [Enhanced] [Enabled] [Enabled] [Enabled] [Enabled] [Enabled] Item Specific Help Table 2-7. Internal Device Configurations Submenu Options Menu Field Options Default Description Serial ATA Controller: • Disabled • Enabled [Enabled] When [Enabled] is selected, the Serial ATA port is enabled. When [Disabled] is selected, the Serial ATA port is disabled. SATA Controller Mode Option: • Enhanced • Compatible [Enhanced] In Compatible mode, S-ATA and P-ATA drives are auto-detected and put into legacy mode. When Enhanced is selected, S-ATA and P-ATA drives are auto-detected and put into Native IDE mode AHCI Configuration: • Disabled • Enabled [Enabled] When [Enabled] is selected, the Advanced Host Controller Interface (AHCI) is enabled. When [Disabled] is selected, the AHCI is disabled. Bluetooth(R): • Disabled • Enabled [Enabled] When [Enabled] is selected, the Bluetooth device is enabled. When [Disabled] is selected, the Bluetooth device is disabled. LAN Controller: • Disabled • Enabled [Enabled] When [Enabled] is selected, the LAN device is enabled. When [Disabled] is selected, the LAN device is disabled. Wireless LAN: • Disabled • Enabled [Enabled] When [Enabled] is selected, the wireless LAN is enabled. When [Disabled] is selected, the wireless LAN is disabled. IEEE1394 Controller: • Disabled • Enabled [Enabled] When [Enabled] is selected, the IEEE 1394 (Firewire) device is enabled. When [Disabled] is selected, the IEEE 1394 (Firewire) device is disabled. BIOS Setup Utility 15 CPU Features Submenu 2 Options for the CPU Features submenu are given in Table 2-8. PhoenixBIOS Setup Utility Exit Submenu Item Specific Help CPU Features Core Multi-Processing: [Enabled] SpeedStep(R) Technology: On Battery: On AC: [Enabled] [Battery Optimized] [Maximum Performance] XD Bit functionality: Virtualization Technology: [Enabled] [Disabled] Select Item Select Menu - Change Values Space Enter Select Sub-Menu ▲ F1 Help ESC Exit Select Core Multi-Processing enabled or disabled. F9 Setup Defaults F10 Save and Exit Table 2-8. CPU Features Submenu Options Menu Field Options Default Description Core Multi-Processing • Disabled • Enabled [Enabled] Enable or disable Core Multi-Processing feature. SpeedStep(R) Technology: • Disabled • Enabled [Enabled] This option enables or disables the Intel SpeedStep Technology. When [Disabled] is selected, the CPU speed is fixed to the lower speed and the Intel SpeedStep Technology applet does not start. When [Enabled] is selected, the Intel SpeedStep applet works using Enhanced SpeedStep Technology. The SpeedStep applet reflects the settings of the BIOS and vice versa. On Battery: • Max Performance • Battery Optimized • Automatic [Battery Optimized] This option allows you to determine the speed of the CPU when battery power is applied. Note that this option is visible but disabled if SpeedStep Technology is disabled. When Max Performance is selected, the CPU runs at high speed. When Batt Optimized is selected, the CPU runs at low speed. When Automatic is selected, the CPU is maximized in busy state and set to the lower speed in the idle state. On AC: • Max Performance • Battery Optimized • Automatic [Maximum Performance] This option allows you to determine the speed of the CPU when power is applied. Note that this option is visible but disabled if SpeedStep Technology is disabled. When Max Performance is selected, the CPU runs at high speed. When Batt Optimized is selected, the CPU runs at low speed. When Automatic is selected, the CPU is maximized in busy state and set to the lower speed in the idle state. BIOS Setup Utility 16 Menu Field Options Default Description XD Bit functionality: • Disabled • Enabled [Enabled] Allows the user to enable and disable the Execute Disable Bit functionality. Execute Disable Bit allows the processor to classify areas in memory where application code can and cannot execute. In the event an internet worm attempts to insert code in the buffer, the processor disables code execution to prevent damage or worm propagation. Virtualization Technology: • DIsabled • Enabled [Disabled] Allows the user to enable or disable the Virtualization Technology. Note that in order for this setting to take effect, the system must be rebooted. BIOS Setup Utility 17 USB Features Submenu 2 Options for the USB Features submenu are given in Table 2-8. PhoenixBIOS Setup Utility Exit Submenu USB Features Legacy USB Support: SCSI SubClass Support: Item Specific Help [Disabled] The feature is disabled. [Enabled] [Enabled] [Enabled] Legacy USB Emulation is enabled and USB devices are available without USB aware OS. Select Item Select Menu - Change Values Space Enter Select Sub-Menu ▲ F1 Help ESC Exit F9 Setup Defaults F10 Save and Exit Table 2-9. USB Features Submenu Options Menu Field Legacy USB Support: Options • Disabled • Enabled Default [Enabled] Description This option enables or disables Legacy USB emulation. When [Disabled] is selected, Legacy USB support is disabled. When [Enabled] is selected, Legacy USB support is enabled, and certain USB devices (such as CD-ROMs and keyboards) can be used without a USB-aware operating system. SCSI SubClass Support: • Disabled • Enabled [Enabled] This option enables or disables support for USB devices that belong to the SCSI subclass in the Mass Storage class (e.g., USB CD-ROM). Note that this option is visible but disabled if Legacy USB Support is disabled. When [Disabled] is selected, the feature is disabled. When [Enabled] is selected, USB devices that belong to the SCSI subclass in the Mass Storage class can be used. Note that enabling this feature could cause the system to hang during POST, depending upon the device that is connected BIOS Setup Utility 18 Miscellaneous Configurations Submenu 2 Options for the Miscellaneous Configurations submenu are given in Table 2-8. PhoenixBIOS Setup Utility Exit Submenu Miscellaneous Configurations Power Button: Wake up on LAN: Force LAN Boot: Auto Save To Disk: Volume Setting: UMA Video Memory Size: Hardware Power Management: [Disabled] [Disabled] [Disabled] [Off] [Middle] [128MB] [Enabled(Level2)] Select Item Select Menu Configures the power button. *ACPI OS ignores this setting. Change Values Space Enter Select Sub-Menu ▲ F1 Help ESC Exit Item Specific Help F9 Setup Defaults F10 Save and Exit Table 2-10. Miscellaneous Configurations Submenu Options Menu Field Options Default Description Power Button: • Disabled • Power Off [Disabled] This option enables or disables the system power button. Note that an ACPI OS overrides this setting. Wake up on LAN: • Disabled • Enabled [Disabled] Enabling this feature will cause the system to wake when the internal LAN receives a Magic Packet while in the Power-Off state. Force LAN Boot: • Disabled • Enabled [Disabled] (Can only be selected when Wake Up On LAN is enabled.) When this is enabled, the system will first try to boot from the LAN before attempting to boot from any other device regardless of the BIOS priority settings or whether Preboot Execution Environment is disabled. Auto Save To Disk: • Off • On [Off] When turned On, when the battery becomes low and the system is in Suspend mode, the system will automatically save its state and then power off. Volume Setting: • • • • [Middle] Allows you to set or disable the system “beep” level. UMA Video Memory Size: • 64MB • 128MB • 224MB [128MB] Select the maximum allocated shared video memory size. UMA memory is dynamically allocated as needed by Intel Dynamic Video Memory Technology (DVMT). Hardware Power Management: • Disabled • Enabled (Level1) • Enabled (Level2) [Enabled (Level2)] This allows you to enable or disable the running of Hardware Power Management. Level1 is standard hardware management; Level2 is deeper than Level1. Off Minimum Middle Maximum BIOS Setup Utility 19 Event Logging Submenu 2 The Event Logging Submenu allows you to configure DMI (Desktop Management Interface) event logging options. To access this submenu, select Event Logging Submenu from the Advanced menu. PhoenixBIOS Setup Utility Exit Submenu Event Logging Event Log Capacity: Event Log Validity: Item Specific Help Space Available Valid View Event Log: [Enter] Event Logging: System Boot Event: [Enabled] [Disabled] Clear All Event Logs: [No] Mark Events as Read: [Enter] Select Item Select Menu -/ Change Values Space Enter Select Sub-Menu ▲ F1 Help ESC Exit Press key to view the contents of the event log. F9 Setup Defaults F10 Save and Exit Table 2-11. Event Logging Submenu Options Menu Field Options Default Description Event Log Capacity ----- ----- Status of the event log is displayed. Event Log Validity ----- ----- Indicates whether data in the event log is valid. View Event Log • Enter ----- Press the key or select the [Enter] option to view the contents of the event log. Event Logging • Disabled • Enabled [Enabled] Determines whether DMI event logging is enabled. System Boot Event • Disabled • Enabled [Disabled] This option is only available when [Enabled] is selected for Event Logging. When [Enabled] is selected, the event may be logged. When [Disabled] is selected, the event is ignored. Clear All Event Logs • No • Yes [No] Choose [Yes] to clear all DMI event logs at the next boot. (This setting is reset to No after the event logs are cleared.) Mark Events as Read • Enter [Enter] Press [Enter] or press the key to mark all events currently in the event log as read. Marked events will not be displayed the next time View Event Log is selected. BIOS Setup Utility 20 Security Menu Options 2 Security menu options for the Stylistic ST5100 Tablet PC are described in Table 2-12. Note that settings for some security menu options determine whether other options are available. Main Advanced PhoenixBIOS Setup Utility Security Boot Info Exit Item Specific Help ▲▲▲ Supervisor Password Is: User Password Is: Clear Clear Set Supervisor Password Set User Password Minimum User Password Length: Password on Boot: On Automatic Wake up: Boot from Removable Media: Flash Write: Hard Disk Security Owner Information Security Chip Setting Security Panel on Resume: [Enter] [Enter] [0] [Disabled] [Disabled] [All] [Enabled] Select Item Select Menu Then password entry is required to enter BIOS Setup. [Enabled] - Change Values Space F9 Setup Defaults Enter Select Sub-Menu F10 Save and Exit ▲ F1 Help ESC Exit Press [Enter] key to set Supervisor Password to enable any password features. Table 2-12. BIOS Setup Security Menu Options Menu Field Options Default Description Supervisor Password Is: • Set • Clear Clear Indicates whether a supervisor password has been specified. (This field cannot be changed directly. To enable or disable the supervisor password, enter a new password or clear the old one using the Set Supervisor Password option.) User Password Is: • Set • Clear Clear Indicates whether a user password has been specified. (This field cannot be changed directly. To enable or disable the user password, enter a new password or clear the old password using the Set User Password option.) Set Supervisor Password* (Tap on the setting field for this option or press the key to specify a supervisor password.) ----- Specifying a supervisor password grants access to all password protected Security menu options. When a supervisor password is enabled and a user password is used to enter BIOS Setup, the user cannot access the following Security menu options: Set Supervisor Password, Floppy Disk Access, and Hard Disk Boot Sector. When enabled, a supervisor password (or user password if used) is required to run BIOS Setup. Set User Password* (Tap on the setting field for this option or press the key to specify a user password.) ----- Specifying a user password grants access to the following Security menu options only: User Password, Password On Boot. Other Security menu options are not accessible. (When a supervisor password is enabled and a user password is used to enter BIOS Setup, the user cannot access the following Security options: Set Supervisor Password, Floppy Disk Access, Hard Disk Boot Sector.) When enabled, a user (or supervisor) password is required to run BIOS Setup. Note that a supervisor password must be enabled before a user password can be specified. * When both the Supervisor and User passwords are set, and a User password is used to enter the BIOS, the following Menu items can be changed: Main -> Language, Advanced -> Video Features -> Display, Advanced -> CPU Features -> (all items), Advanced -> Miscellaneous Configurations -> (all items), Advanced -> Events Logging -> View Event Log, Security -> Set User Password, Exit -> Exit Saving Changes, Exit -> Exit Discarding Changes, Exit -> Save Changes. BIOS Setup Utility 21 Table 2-12. BIOS Setup Security Menu Options (Continued) Menu Field Options Default Description Minimum User Password Length: [0] ----- Set the minimum length for the user password. Once this field is set, the user cannot enter any passwords less than the minimum length. Password On Boot: • Disabled • First Boot • Every Boot [Disabled] Select [First Boot] to require a user or supervisor password to boot the system the first time. Select [Every Boot] to require a user or supervisor password to boot the system every time the system is booted. Note that a user or supervisor password must be specified before this option can be enabled. On Automatic Wake up: • Disabled • Enabled [Disabled] This feature is only available when Password on Boot: is enabled. When enabled, password entry is required on automatic wake up by LAN or RTC. When disabled, password entry is not required on automatic wake up by LAN or RTC. Boot from Removable Media: • All • Supervisor Only [All] This option determines who has permission to boot the system using removable media. Select [Supervisor Only] to allow the system only to be booted from removable media after the system is started by entering a supervisor password when the Password On Boot option is enabled. When [Supervisor Only] is selected, the system cannot be booted from removable media if Supervisor Password is enabled and the Supervisor password was not entered at boot time. Flash Write: • Disabled • Enabled [Enabled] When set to disabled, the BIOS Flash memory will be write protected. Hard Disk Security Submenu ____ ____ Enter this submenu to change hard disk security. (See “Hard Disk Security Submenu” on page 23 for details). Owner Information Submenu ____ ____ Enter this submenu to change owner information. (See “Owner Information Submenu” on page 24 for details). Security Chip Setting ____ ____ Enter this submenu to enable or disabled the security chip. Security Panel on Resume: • Disabled • Enabled [Enabled] When enabled, the Security Panel feature is enabled upon Resume from Suspend. When disabled, the Security Panel feature is disabled upon Resume from Suspend. BIOS Setup Utility 22 Hard Disk Security Submenu 2 The Hard Disk Security Submenu allows you to enable or disable the Primary Master device. To access this submenu, select Hard Disk Security from the Security menu. Main Advanced PhoenixBIOS Setup Utility Exit Submenu Power Savings Hard Disk Security Drive0: Set Master Password Set User Password Password Entry on Boot: Select Item Select Menu Item Specific Help Clear [Enter] [Enter] [Enabled] Change Values Space Enter Select Sub-Menu ▲ F1 Help ESC Exit Exit F9 Setup Defaults F10 Save and Exit Table 2-13. Hard Disk Security Submenu Options Menu Field Options Default Description Note that when a Master Password is set for a hard disk drive, the hard disk drive will only function in a system that has the same hard disk drive password. If the drive is put into another system with no password or with a different password, the hard disk drive will not work. Note, however, that the data on the drive is not encrypted. The hard disk cannot be set or changed if the system is rebooted from the operatinf system.If you choose “Save Changes and Power Off” in the Exit menu to shut down the system, then the hard disk password can be set or changed on the next boot. Drive0 Clear ----- Display only. Either Clear or Set, depending upon whether a Master Password is entered in the following field. Set Master Password ----- ----- Allows you to enter a master password when a supervisor password has been set. Set User Password ----- ----- Allows you to enter a user password when a supervisor password has been set. Password Entry on Boot: • Disabled • Enabled [Enabled] When set to disabled, the Hard Disk Password entry is not required before OS boot. Note that the hard disk is still password-protected without password entry. BIOS Setup Utility 23 Owner Information Submenu 2 The Owner Information Submenu allows you to enter information about the owner and to change the foreground and background colors. To access this submenu, select Owner Information from the Security menu. Note that the owner information is only displayed if Diagnostic Screen is enabled. PhoenixBIOS Setup Utility Exit Submenu Owner Information Owner Information Is: Clear Set Owner Information [Enter] Foreground Color: Background Color: [Gray] [Black] Select Item Select Menu Change Values Space Enter Select Sub-Menu ▲ F1 Help ESC Exit Item Specific Help F9 Setup Defaults F10 Save and Exit Table 2-14. Owner Information Submenu Options Menu Field Options Default Description Owner Information Is: –— Clear Display only. Set Owner Information: –— [Enter] Field to write owner information (e.g., name). Foreground Color: • • • • • • Black Blue Green Cyan Red Magenta • • • • • Brown White Gray Light Blue Light Green • • • • • Light Cyan Light Red Light Magenta Yellow Bright White [Gray] Select a color for the foreground. Background Color: • • • • • • Black Blue Green Cyan Red Magenta • • • • • Brown White Gray Light Blue Light Green • • • • • Light Cyan Light Red Light Magenta Yellow Bright White [Black] Select a color for the background. BIOS Setup Utility 24 Security Chip Setting Submenu 2 The Security Chip Setting Submenu allows you to enable or disable the security chip in your system. To access this submenu, select Security Chip Setting from the Security menu. PhoenixBIOS Setup Utility Exit Submenu Security Chip Setting Security Chip: Clear Security Chip [Enabled] [Enter] Security Chip State: Enabled Activated Select Item Select Menu Change Values Space Enter Select Sub-Menu ▲ F1 Help ESC Exit Item Specific Help F9 Setup Defaults F10 Save and Exit Table 2-15. Security Chip Setting Submenu Options Menu Field Options Default Description Security Chip: • Disabled • Enabled [Enabled] Allows you to enable or disable the Security Chip. When disabled, the following field does not appear. Clear Security Chip ____ [Enter] Allows you to clear the security chip. Note that if you clear the security chip, you will not be able to access data that has already been encrypted. Security Chip State: ____ Enabled Activated Display only. Indicates the current state of the security chip. BIOS Setup Utility 25 Boot Menu Options 2 Boot menu options are described in Table 2-16. Main Advanced PhoenixBIOS Setup Utility Security Boot Info Exit Item Specific Help ▲ Quick Boot: Boot Time Diagnostic Screen: Boot Menu: Preboot Execution Environment: Boot Device Priority [Enabled] [Disabled] [Enabled] [Disabled] [Disabled] All diagnostic tests will be done. [Enabled] Some diagnostic tests may be skipped while booting to speed up. Select Item Select Menu -/ Change Values Space Enter Select Sub-Menu ▲ F1 Help ESC Exit F9 Setup Defaults F10 Save and Exit Table 2-16. BIOS Setup Boot Menu Options Menu Field QuickBoot Options • Disabled • Enabled Default [Enabled] Description Determines whether the full set of tests are run during the Power-On Self Test (POST). When [Enabled] is selected, a less extensive memory test is performed and the size of installed memory is not displayed during the memory test. When [Disabled] is selected, the full set of tests is run. Boot Time Diagnostic Screen • Disabled • Enabled [Disabled] Determines whether status messages are displayed as the Power On Self Test (POST) is performed. Select [Enabled] to display messages. If [Disabled] is selected, messages are not displayed and the logo screen is displayed. (If POST errors occur, POST messages are displayed regardless of this setting.) Boot Menu: • Disabled • Enabled [Enabled] This field is not active unless the Supervisor’s Password has been set. When disabled, access to the Boot Menu with the [F12] key is disabled. When enabled, the Boot Menu is enabled and the [F12] key will allow you to display it. Preboot Execution Environment • Disabled • Enabled [Disabled] Determines whether to boot up from a network server. Select [Enabled] to allow the system to boot from a network server (Preboot Execution Environment). If [Disabled] is selected, this feature is disabled. Boot Device Priority Submenu ----- ----- Select this submenu to configure the order in which drives are searched for a bootable image. BIOS Setup Utility 26 Boot Device Priority Submenu 2 Table 2-17. describes settings in the Boot Device Priority submenu. Main Advanced PhoenixBIOS Setup Utility Security Power Savings Boot Boot Device Priority Item Specific Help Keys used to view or configure devices: Boot priority order: 1: Floppy Disk Drive 2: Drive0: FUJITSU MHV2060BH PL 3: CD/DVD Drive 4: NETWORK: B02 D00 Yukon PXE 5: 6: 7: 8: Excluded from boot order: : USB MEMORY: None : USB HDD: None Select Item Select Menu - Change Values Space F9 Setup Defaults Enter Select Sub-Menu F10 Save and Exit ▲ F1 Help ESC Exit <+>/ or <-> moves the device up or down. exclude or include the device to boot. Table 2-17. BIOS Setup Boot Sequence Submenu Setting Description Menu Field Description Boot priority order: 1: Floppy Disk Drive 2: Drive0: 3: CD/DVD Drive 4: NETWORK: 5: 6: 7: 8: Excluded from boot order: : USB MEMORY: : USB HDD: The boot selections determine the order in which the BIOS searches for the operating system during a startup sequence. To change the order, highlight one source by using the [up] or [down] cursor keys and then press the [+] or [-] key to change the order number. Tapping [x] removes from the list a device that is not installed. Tapping [x] on an item in the Excluded list adds the device to the Boot priority list. Be sure to save your changed order when you exit the BIOS setup utility. NOTE: Be aware that if you use the CD-ROM drive as the first boot device, certain files may be overwritten, depending upon your operating environment. BIOS Setup Utility 27 Info Menu 2 The Info menu displays information about the Tablet PC hardware and BIOS software installed on the system as described in Table 2-18. Main PhoenixBIOS Setup Utility Security Boot Info Advanced BIOS Version: BIOS Date: BIOS Area: 1.06 10/12/2006 E000h - FFFFh CPU Type: CPU Speed: L1 Cache: L2 Cache: Genuine Intel(R) CPU U2500 1.20 GHz 128 KB 2048 KB Exit Total Memory: 512 MB Memory Slot 1: 512 MB DDR2 SDRAM Memory Slot 2: None Select Item Select Menu -/ Change Values Space Enter Select Sub-Menu ▲ F1 Help ESC Exit F9 F10 Setup Defaults Save and Exit Table 2-18. BIOS Setup Info Menu Field Description BIOS Version: Version number of the BIOS software installed on system. BIOS Date: Release date of the BIOS software. BIOS Area: Memory area used by the BIOS. CPU Type: CPU type used. CPU Speed: Processor speed. L1 Cache: Size of CPU level 1 cache. L2 Cache: Size of CPU level 2 cache. Total Memory: Total memory installed in Tablet PC (including built-in memory). Memory Slot 1: Total memory installed in memory slot 1. Memory Slot 2: Total memory installed in memory slot 2. BIOS Setup Utility 28 Exit Menu Options 2 Exit menu options are described in Table 2-19. Main PhoenixBIOS Setup Utility Security Power Boot Advanced Info Exit Item Specific Help Exit Saving Changes Exit Discarding Changes Load Setup Defaults Discard Changes Save Changes Save Changes and Power Off Select Item Select Menu - Change Values Space Enter Select Sub-Menu ▲ F1 Help ESC Exit Exit System Setup and save your changes to CMOS. F9 F10 Setup Defaults Save and Exit Table 2-19. BIOS Setup Exit Menu Options Menu Field Description Exit Saving Changes Exit Saving Changes and Exit will store all the entries on every menu of the setup utility to the BIOS memory and then exit the setup utility. A confirmation message Save Configuration changes and exit now? [Yes] [No] will be displayed. Exit Discarding Changes Selecting Exit Discarding Changes and Exit will exit the setup utility immediately without writing to the BIOS memory and without displaying a confirmation screen. When the BIOS recognizes this selection it will load the operating system and begin operation. Load Setup Defaults Selecting Load Setup Defaults will load the factory preset default values for all menu fields, then display the message Load default configuration now? [Yes] [No]. When confirmed the setup utility will return to the Exit Menu. Discard Changes Selecting Discard Changes will load the previous values in BIOS memory for all menu fields. The message Load previous configuration now? [Yes] [No] will be displayed. When confirmed the setup utility will return to the Exit menu. Save Changes Selecting Save Changes will cause the new settings in all menus to be written to the BIOS memory. The message Save configuration changes now? [Yes] [No] will be displayed. When confirmed, the setup utility will return to the Exit menu. Save Changes and Power Off Selecting Save Changes and Power Off will cause the new settings in all menus to be written to the BIOS memory, then power the system off. The message Save configuration changes now and power off? [Yes] [No] will be displayed. When confirmed, the setup utility shut down the system. BIOS Setup Utility 29 Chapter 3 Hardware Specifications Specifications for the Stylistic ST5100 Tablet PC and Tablet Dock are given in this chapter. General Specifications 3 General specifications for the Tablet PC are given in Table 3-1. Table 3-1. General System Specifications Feature Specification Comments Microprocessor Intel® Core™ Duo Processor ULV U2500 (1.20 GHz, 2 MB L2, 533 MHz FSB) Chipset Intel 945GM and ICH7-M Front Side Bus (FSB) 533 MHz Cache Level 1 (L1) cache: 64 KB Level 2 (L2) cache: 2 MB L1 and L2 caches are always enabled. BIOS ROM 1 MB Boot block type flash ROM, 48 pin RAM (expansion) Two 200-pin SO-DIMM slots, DDR2 533 MHz. Supports up to 4 GB memory. Memory Bus Clock: 533 MHz Total allowable RAM is 4 GB. (2 GB in each slot) Graphics • Controller: Internal VGA • Intel GMA950 chipset with shared memory using UMA and DVMT. • 3D accelerator • AGP support (internal circuit) • MPEG-2 support Unified Memory Architecture (UMA) delivers low-power, high-performance 3D/2D graphics, video, and display capabilities. Dynamic Video Memory Technology (DVMT) responds dynamically to application requirements and allocates the proper amount of memory (128 MB max.) for optimal graphics and system performance. I/O Controller SMSC LPC47N227 Controller for IrDA and communication with Tablet Controller. PC Card Controller OZ711MP1 (3 slot) Controller is on PCI bus. Supports CardBus (PCI bridge) and PCIC protocols. The controller does not support Zoomed Video. • Type II CardBus slot x 1 • Dedicated Smart Card slot x 1 • SD/Memory Stick slot x 1 LAN Controller Marvell Yukon 88E8055 PCI-E Gigabit Ethernet IEEE 1394 Controller OZ711MP1 USB Controller Integrated ICH7-M (USB 2.0) CPU Temperature Monitor Analog Devices ADM1030-R4 IrDA Module Agilent Technologies HSDL-3602 TPM Module Infineon SLD9630TT1.2 Bluetooth Module UGXZ5-102A Fingerprint Sensor AuthenTec AES2501A Bluetooth V2.0 30 Table 3-1. General System Specifications (Continued) Feature Specification Audio Codec Sigmatel STAC9228 ASIC ANN (Compatible with HOOP) Comments 12.1” model: dual-mic, 10.4”: single-mic Communications Devices • Onboard LAN: Marvell Yukon 88E8055 PCI-E Gigabit Ethernet, 10BASE-T/ 100BASE-T/1000BASE-T • Modem: Agere AC-Link MDC1.5 • Wireless LAN (Mini-PCI): Atheros AR5006EXS Wireless network card 802.11a/b/g, or, Intel PRO/Wireless 3945ABG Network Connections 802.11a+b/g Hard Disk Drive • • • • Shock-mounted S-ATA 150 Smart Support Fujitsu Shock Sensor technology Depending upon configuration: 40 GB, 60 GB, 80 GB, 100 GB, or 120 GB @ 5400 rpm Digitizer Specifications 3 Specifications for the two different Stylistic ST5100 Tablet PC digitizers are given in Table 3-2.. Table 3-2. Digitizer Specifications Feature Feature Active Digitizer Sensor Unit for 12.1” LCD Sensor Unit for 10.4” LCD Type Electromagnetic digitizer Electromagnetic digitizer Area 9.75” x 7.33” (247.8 mm x 186.3 mm) 9.26” x 5.8” (235.3 mm x 147.4 mm) Resolution 0.01 mm 0.01 mm Sampling Rate 133 pps 133 pps Interface Serial interface Serial interface Vendor Wacom Wacom Pen Weight: 0.53 oz. (15g). Size: 5.51” (length) x 0.35” (diameter) (140 mm x 9 mm) Vendor: Wacom External Video Capabilities 3 The Stylistic ST5100 Tablet PC Tablet Dock can drive an external video monitor. You can select an external monitor, the Tablet PC display screen, or both as the active video display. The Tablet PC supports VGA, SVGA, and XGA video modes with external monitors. Screen resolutions supported are given in Table 3-3. Table 3-3. Supported Video Modes for External Monitors Video Configuration Resolution Colors The Stylistic ST5100 Tablet PC video driver supports Extended Desktop (extended desktop maximum resolutions are the same as the supported video modes listed below). CRT only Max. 1600 x 1200 Up to 16 M Simultaneous Max. 1024 x 768 Up to 16 M Digitizer Specifications 31 Display Specifications 3 Specifications for the Stylistic ST5100 Tablet PC display are given in Table 3-4. Table 3-4. Display Specifications Feature Specification Transmissive XGA LCD • 12.1" diagonal TFT Color • Indoor/outdoor viewability • XGA 1024 x 768 dot composition • Aspect ratio: 4:3 • Dot pitch: 0.2400 mm • Transmissive • 260K colors • Active area: 9.67” x 7.25” (245.76 mm x 184.32 mm) • Brightness: 8 gradations • Backlight: FL Tube; brightness: ~20-150 Cd/m2 Reflective XGA LCD • 10.4" diagonal TFT Color • XGA 1024 x 768 dot composition • Aspect ratio: 4:3 • Dot pitch: 0.2055 mm • Reflective • 260K colors • Active area: 8.28” x 6.21” (210.43 mm x 157.82 mm) • Brightness: 8 gradations • Frontlight: FL Tube; brightness: ~0 - 45 Cd/m2 Environmental Specifications 3 Environmental specifications for the Stylistic ST5100 Tablet PC are given in Table 3-5. Table 3-5. Environmental Specifications Feature Specification Temperature Operating: 41° to 95°F (5° to 35°C) Nonoperating: 14° to 140°F (-10° to 60°C) (with appropriate power management) Humidity Operating: 20% to 80% RH noncondensing Nonoperating: 20% to 80% RH noncondensing Vibration 0.67G, Random Display Specifications 32 Peripheral Interface Specifications 3 Specifications for peripheral interfaces on the Tablet PC are given in Table 3-6. For specifications on peripheral interfaces provided by the Tablet Dock, see “Tablet Dock Specifications” later in this chapter. Also note that pin assignments and other details for peripheral interfaces on the Stylistic ST5100 Tablet PC are given in Chapter 4. Table 3-6. Peripheral Interface Specifications Feature Specification Comments PC Card Slot One Type II PCMCIA CardBus slot. Compliant with PC Card Standard Rev. 3.0 Supports CardBus and PCIC (PC Card I/O Cards). Smart card via adapter is not supported by this slot. Modem Port RJ-11 connector for internal modem See “Internal Modem Specifications” on page 35 for more information. LAN Port RJ-45 connector for internal LAN. See “Internal LAN Specifications” on page 35 for more information. External Monitor Port Analog RGB mini D-Sub 15-pin connector that allows you to connect an external monitor. See Table 3-3, “Supported Video Modes for External Monitors,” on page 31 for more details. Universal Serial Bus Port (USB A) 2.0 Two (2) USB 2.0 Series A receptacles on Tablet PC. IrDA Port Infrared transceiver built into Tablet PC. Smart Card Slot Dedicated Smart Card slot SD/Memory Stick Slot Secure Digital/Memory Stick slot Infrared Keyboard Ports IR receivers built into the Tablet PC for use with optional infrared keyboard or mouse. Proprietary Fujitsu receivers. Range: approximately 1 M, 15o from center DC Power Input 16 VDC ±10%, 3.75 A Connector vendor: Hosiden (Hosiden part number HEC3900-01-010) This connector is a EIAJ-RC5320A standard connector. External power can be connected to DC input connector on the Tablet PC or Tablet Dock. See “DC Power Inputs” on page 50 for more details. Audio Jacks Stereo microphone input mini jack Stereo headphone output mini jack Standard 3.5 mm mini jacks. See “Audio Jacks” on page 43 for details on audio inputs and outputs. IEEE 1394 Jack S400, 4-pin connector System Interface Port 100-pin connector Compliant with IrDA Standard Revision 1.1 Supports: FIR (4 Mbps max), SIR (115 Kbps max) Range: approximately 1 M, 15 degrees from center For use with Stylistic ST5100 Tablet Dock. Physical Specifications 3 Physical specifications for the Stylistic ST5100 Tablet PC are given in Table 3-7. Table 3-7. Stylistic ST5100 Tablet PC Specifications Feature Specification Tablet PC Dimensions 10.4” Model: 8.66” (w) x 12.77” (d) x 0.92/1.01” (h) (220 mm x 324.4 mm x 23.29/25.7mm) 12.1” Model: 8.66” (w) x 12.77” (d) x 0.82/0.94” (h) (220 mm x 324.4 mm x 20.9/23.8mm) Tablet PC Weight (with battery pack) 10.4” Model: 3.4 lbs. (1.54 Kg); 12.1” Model: 3.5 lbs (1.61 Kg) Peripheral Interface Specifications 33 Power System Specifications 3 Specifications for the Stylistic ST5100 Tablet PC power system are given in Table 3-8. The power system and power management characteristics are further described in Chapter 5 of this manual. Table 3-8. Power System Specifications Feature Specification Comments Power Management Standard Supported ACPI Specification Revision 1.0 Battery Pack Rechargeable 6-cell lithium ion battery pack: Charge times are for a 0% charged battery pack charging in Tablet PC (not in an external battery charger). • Capacity: 5200 mAh, 56 Wh • Nominal operating voltage: 10.8 V • Charge time: Approximately 4.5 hours • Size: 218.2 5 mm (w) x 50.9 mm (d) x 22.3 mm (h) • Weight: Approximately 330g If the battery pack charge is 90% or higher when you connect DC power, the battery pack will not charge, thus preventing overcharging. Battery life values are approximate. Rechargeable 9-cell lithium ion battery pack: • Capacity: 7800 mAh, 84 Wh • Nominal operating voltage: 10.8 V • Charge time: Approximately 6.0 hours • Size: 218.2 mm (w) x 59.7 mm (d) x 22.3 mm (h) • Weight: Approximately 480g Contact layout: GND1 GNDA ESDA1 ESCL1 BT1ID BT1IN BATTM+ SCONT1 VSENSE1 BATT1 Bridge Battery • Nickel metal hydride Bridge battery supplies power to RAM in suspend mode for about 5 minutes while battery pack is removed. • 6 cells • Capacity: 6.0 V, 35 mAH (210 mWh) Sub Battery • Suspend life (backup battery only): Approximately 5 minutes • In all modes when external DC power is connected. • In On, Idle, or Standby modes (when system is running) when external DC power is not connected. • Lithium battery (built in) Provides real time clock power backup. Approximate battery life is 5 years. (Not field replaceable.) • 210 mAh AC Adapter Bridge battery is charged: • Input: 100-240 VAC, 50/60 Hz • Output: 16 VDC ±10%, 3.75 A Power System Specifications 34 Internal Modem Specifications 3 The internal modem device connects to the system’s PCI bus. Specifications for the internal modem are given in Table 3-9. The internal modem is built-in and is not field replaceable. Table 3-9. Internal Modem Specifications Feature Specification Interface HD Audio Size 35 mm (w) x 27.6 mm (d) x 5.2 mm (h) Chip Agere Systems CSP1040 AC-Link Soft Modem Chipset Data Mode Capability • ITU-T V.90 • ITU-T V92 • ITU-T V.34 extended rate, V32bis, V32, V22bis • TIA/EIA 602 standard for AT command set • V.42 error correction • V.42bis and MNP Class 5 data compression Fax Mode Capability • ITU-T V17, V29, V27ter, V21 ch2 • TIA/EIA 578 Class 1 Fax Support Countries USA, Canada, Japan, Singapore, Malaysia, Australia, New Zealand, UK, France Germany, Finland, Sweden, Norway, Portugal, Spain, Italy, Belgium, Greece, Austria, Denmark, Ireland, Luxembourg, Netherlands, Switzerland, Cyprus, Czech Republic, Estonia, Hungary, Iceland, Latvia, Liechtenstein, Lithuania, Malta, Poland, Slovak Republic, Slovenia, Bangladesh, Bulgaria, China, Colombia, Egypt, Hong Kong, India, Indonesia, Israel, UAE, Korea, Kuwait, Lebanon, Mexico, Morocco, Oman, Pakistan, Peru, Phillipines, Romania, Russia, Saudi Arabia, Sri Lanka, Taiwan, Thailand, Turkey, Venezuela, Chile, Uruguay. Supply Voltage 3.3v Storage Humidity 80% RH Manufacturer Fujitsu Media Devices Internal LAN Specifications 3 The internal LAN device connects to the system’s PCI bus. Specifications for the internal modem are given in Table 3-10. The internal modem is built-in and is not field replaceable. Table 3-10. Internal LAN Specifications Feature Bus Connection Specification • PCI-E • Internal wired 10Base-T/100Base-Tx/1000* Base-T/Tx Ethernet LAN. *1000 Mbps, commonly referred to as Gigabit Ethernet. Location On-board Chip Marvell Yukon 88E8055 PCI-E Gigabit Ethernet Additional Features Wake On LAN support Internal Modem Specifications 35 Agency Approval Specifications 3 Specifications for government agency approvals are given in Table 3-11. Table 3-11. Agency Approval Specifications Feature Specification Emissions • FCC Part 15, Class B • EN55022 (CISPR22) Class B • VCCI Class B Immunity • EN55024 (1998) Safety • UL and cUL Listed, UL 60950, 3rd edition • CB Report, IEC 60950-1, 1st edition Telecom • FCC Part 68 • IC CS-03 Specific Absorption Rate (SAR) • FCC/RSS • ACA/EN Wireless • EN300328 • EN301489 • EN301893 • FCC 15E • RSS210 • RSS220 Other • Energy Star Tablet Dock Specifications 3 The Stylistic ST5100 Tablet Dock is designed to provide optimal support for your Tablet PC. Specifications for interfaces on the Stylistic ST5100 Tablet Dock are given in Table 3-12. Note that these interfaces duplicate corresponding ports on the Tablet PC. For details on peripheral interfaces provided by the Tablet Dock, refer to Chapter 4 of this manual. Table 3-12. Stylistic ST5100 Tablet Dock Specifications Feature Specification Comments DC power input + tip / - sleeve 16 VDC ±10%, 3.75 A See “DC Power Input Connector Pin Assignments” on page 37 for more details. External Monitor (VGA) Port Standard 15-pin video connector System supports simultaneous operation of external monitor with LCD. LAN Port Standard RJ-45 port See “Internal LAN Specifications” on page 35 for more information. Line Output Jack 3.5 mm mini stereo jack Using the line output jack does not disable any other audio features on the Tablet PC or Tablet Dock. (The line output jack is not disabled when other audio jacks are used.) Universal Serial Bus 2.0 Ports Three (3) USB Series A receptacles IEEE 1394 Port S400, 4-pin Agency Approval Specifications 36 Chapter 4 Peripheral Interfaces Details on peripheral interfaces on the Stylistic ST5100 Tablet PC and/or Tablet Dock are described in this chapter. The Stylistic ST5100 Tablet PC and Tablet Dock provide the following peripheral interfaces: Table 4-1. Peripheral interfaces Interface Tablet PC Quantity Tablet Dock Quantity DC Input connector 1 1 Wireless LAN port 1 -- IEEE 1394 jack 1 1 External Monitor port 1 1 Line Out jack -- 1 IrDA port 1 -- Infrared keyboard port 2 -- Universal Serial Bus (USB) 2.0 port 2 3 RJ-11 modem jack 1 -- RJ-45 LAN jack 1 1 Stereo headphone jack 1 -- Microphone jack 1 -- PC Card socket 1 -- Smart Card slot 1 -- SD/Memory Stick slot 1 -- System interface port* 1 1 * Note that the system interface port allows you to connect the optional Stylistic ST5100 Tablet Dock. Pin assignments for peripheral interfaces on the Stylistic ST5100 Tablet PC are given in the following sections. DC Power Input 4 The DC power input connector connects to the AC adapter or auto adapter to power the Tablet PC. The DC power input connector is a two-conductor connector with a center pin and sleeve. Pin assignments for this connector are given in Table 4-2. Table 4-2. DC Power Input Connector Pin Assignments Conductor Description Center Pin 16 Volts DC ±10%, 3.75 A Sleeve Ground Comments (Hosiden part number HEC3900-01-010) This connector is a EIAJ-RC5320A standard connector. S When a DC power source is connected to the DC power input on the Tablet PC, circuitry built into the Tablet PC provides protection against reverse polarity and over voltage. DC Power Input 37 Universal Serial Bus Port 4 The Tablet PC and Tablet Dock provide Universal Serial Bus (USB) ports that are compliant with the Universal Serial Bus Specification Revision 2.0. A USB port is a powered USB hub and can support concurrent operation of up to 127 devices. The Stylistic ST5100 Tablet PC provides two USB ports, and functions as a USB host. The system supports high-power, bus-powered functions as defined in the USB specification. System resources for the USB are assigned by the operating system, no software configuration is necessary; however, it may be necessary to install drivers and application software to support your USB device. The Stylistic ST5100 Tablet Dock provides three USB ports. Ensure that your USB configuration does not exceed the individual port maximum load on the total system load. Note that the conductor gauge and length of your USB cabling will affect the voltage drop and signal propagation between USB devices. Refer to the Universal Serial Bus Specification for details on cable requirements or contact your cable vendor (see “Related Documentation” on page 2.) Also note that some USB devices are self-powered and do not draw power over the USB cable. Contact pin assignments for the USB port are shown in the table below. Table 4-3. USB Port Contacts Contact Pin Locations Position 3 Contact Number Signal Name Signal Description 1 5V Cable power (+ 5 volts DC, 500mA) 2 DATA - Data 3 DATA + Data 4 GND Position 2 Position 4 Position 1 Cable ground IrDA Port 4 The IrDA port on the Stylistic ST5100 Tablet PC is compliant with the Infrared Data Association (IrDA) Standard Revision 1.1. Specifications for the IrDA port on the Tablet PC are given below. Before you can use the IrDA port, the Serial Port B Device BIOS option must be set to IrDA or FIR. See “IrDA Port Configuration Submenu Options” on page 12 for details on BIOS options for the IrDA port. Table 4-4. IrDA Port Specifications Feature Specification Standard supported IrDA Standard Revision 1.1 Distance Up to 1 meter point to point (environmental conditions affect usable range) Conveyable wave Infrared rays (wavelength peak 875 nm) Signal Send data / Receive data Modulation/Data Rate IrDA SIR: 9.6 - 115.2 Kbps IrDA FIR: 4,000.0 Kbps Angle 0° to 15° from center of beam (30° viewing angle) Universal Serial Bus Port 38 Tablet Dock Interface Port 4 NOTES The Tablet Dock interface port on the Stylistic ST5100 Tablet PC allows you to attach the Stylistic ST5100 Tablet Dock. The interface port is a 100-pin connector. The following figure and table show the pin locations for the interface port connector on the Tablet PC. Signals designated with the “pound” (#) symbol are active low. 100 99 50 49 • Signal names listed in the second column of this table are not industry standard signal names. They are provided to assist in cross-referencing these signal names when they appear elsewhere. • The connectors used for the system interface port are manufactured by Hirose. Connector part numbers are: EX80-1005 (main unit) and EX80-100P1 (tablet dock side) 98 97 54 53 48 47 4 3 52 51 2 1 Table 4-5. Tablet Dock Interface Connector Pin Assignments Pin Signal Name Level Description 1 GND1 2 GND1 GND Ground 3 SAFE +5V Dock Detect 4 PWR_DOCK 5 PWR_DOCK 6 PWR_DOCK 7 PWR_DOCK 8 PWR_DOCK +5V PWR_DOCK 9 PWR_DOCK 10 PWR_DOCK 11 PWR_DOCK 12 BAY1-ON -- -- 13 GND1 GND Ground 14 USB_P4NC 15 USB_P4PC 16 GND1 17 USB_P6PC 18 USB_P6NC 19 GND1 Port or Connector Docking Station -- USB GND Ground GND Ground Tablet Dock Interface Port 39 Table 4-5. Tablet Dock Interface Connector Pin Assignments Pin Signal Name Level Description GND Ground GND Ground 20 Reserve 21 Reserve 22 GND1 23 Reserve 24 DOCK_ID1 25 GND 26 ROTATE 27 GND1 28 TRD0+ Giga-LAN 29 TRD0- Giga-LAN 30 GND1 31 TRD1+ Giga-LAN 32 TRD1- Giga-LAN 33 GND1 34 Reserve 35 TRD2+ Giga-LAN 36 TRD2-D Giga-LAN 37 GND1 GND Ground 38 GND1 GND Ground 39 TRD3+ 40 TRD3- 41 GND1 42 Reserve 43 GNDAUD 44 SENSE 45 GNDAUD 46 LOUTL 47 GNDAUD 48 LOUTR 49 GNDAUD 50 DOCK_ON1 51 PWR_EXDCIN 52 PWR_EXDCIN GND GND Port or Connector Ground Ground Giga-LAN Giga-LAN Ground GND Ground GND Ground Giga-LAN for Audio Line-Out GND Ground for Audio Line-Out GND Ground for Audio Line-Out GND Ground +16V DC-IN for Audio Tablet Dock Interface Port 40 Table 4-5. Tablet Dock Interface Connector Pin Assignments Pin Signal Name Level Description 53 GND1 54 GND1 55 GND1 56 GND1 57 GND1 GND Ground 58 GND1 59 GND1 60 GND1 61 GND1 62 Reserve 63 Reserve 64 Reserve 65 Reserve 66 Reserve 67 Reserve 68 Reserve 69 GND1 GND Ground 70 DOCK_FANON# 71 FAN_TACH2_ DOCK 72 Reserve 73 Reserve 74 Reserve 75 Reserve 76 Reserve 77 GND1 78 D_VGACLK 79 D_VGADATA 80 GND1 81 D_VGAVS 82 D_VGAHS 83 GND1 GND Ground 84 GND1 GND Ground 85 D_VGAB Port or Connector For debugging GND Ground CRT GND Ground CRT for CRT CRT Tablet Dock Interface Port 41 Table 4-5. Tablet Dock Interface Connector Pin Assignments Pin Signal Name Level Description Port or Connector 86 GND1 GND Ground for CRT 87 D_VGAG 88 GND1 89 D_VGAR 90 GND1 GND Ground 91 GND1 GND Ground 92 GND1 GND Ground 93 D_TPB1- IEEE 1394 94 D_TPB1+ IEEE 1394 95 GND1 96 D_TPA1- IEEE 1394 97 D_TPA1+ IEEE 1394 98 GND1 GND Ground 99 GND1 GND Ground 100 SAFE CRT GND Ground for CRT CRT GND Ground for CRT for IEEE 1394 for IEEE 1394 for IEEE 1394 Tablet Dock Interface Port 42 Audio Jacks 4 when outputs on the Tablet PC and Tablet Dock are used. Note that using one of the jacks on the system, the other system device is disabled (e.g., when an external microphone is used, the internal microphone is disabled). All audio jacks on the Stylistic ST5100 Tablet PC are stereo mini jacks. Some audio functions on the Tablet PC are disabled when audio jacks are used. Table 4-6 shows which audio inputs are disabled when inputs on the Tablet PC and Tablet Dock are used (enabled). Table 4-7 shows which audio outputs are disabled Table 4-6. Active Audio Inputs Tablet Dock Tablet PC Input Activity Microphone (built-in) Microphone Input Jack Line Input Jack Microphone On (microphone built into Tablet PC) Enabled Plug not inserted NA Tablet PC Microphone jack used (external microphone connected) Disabled Enabled NA “NA” indicates that the condition does not apply. (The condition has no effect on the given input.) Table 4-7. Active Audio Outputs Tablet PC Tablet Dock Output Activity Speaker (built-in) Headphone Jack Line Output Jack Speaker On (speaker built into Tablet PC) Enabled Plug not inserted NA Tablet PC Headphone jack used (external headphone connected) Disabled Enabled NA Tablet Dock Line Output jack used NA NA Enabled “NA” indicates that the condition does not apply. (The condition has no effect on the given output.) Audio Jacks 43 PC Card Port 4 The PC Card socket is compliant with PCMCIA Card standard 3.0. The table and figure below show the pin assignments and pin locations for the PC Card port. 1 2 3 4 5 30 31 32 33 34 35 36 37 38 39 64 65 66 67 68 Table 4-8. PC Card Pin Assignments 16-bit PC Card Interface CardBus 16-bit PC Card Interface Pin Memory-Only I/O & Memory 24 A5 A5 CAD21 CardBus Pin Memory-Only I/O & Memory 1 GND GND GND 25 A4 A4 CAD22 2 D3 D3 CAD0 26 A3 A3 CAD23 3 D4 D4 CAD1 27 A2 A2 CAD24 4 D5 D5 CAD3 28 A1 A1 CAD25 5 D6 D6 CAD5 29 A0 A0 CAD26 6 D7 D7 CAD7 30 D0 D0 CAD27 7 CE1# CE1# CCBE0# 31 D1 D1 CAD29 8 A10 A10 CAD9 32 D2 D2 RFU 9 OE# OE# CAD11 33 WP IOIS16# CCLKRUN# 10 A11 A11 CAD12 34 GND GND GND 11 A9 A9 CAD14 35 GND GND GND 12 A8 A8 CCBE1# 36 CD1# CD1# CCD1# 13 A13 A13 CPAR 37 D11 D11 CAD2 14 A14 A14 CPERR# 38 D12 D12 CAD4 15 WE# WE# CGNT# 39 D13 D13 CAD6 16 READY IREQ# CINT# 40 D14 D14 RFU 17 VCC VCC VCC 41 D15 D15 CAD8 18 VPP1 VPP1 VPP1 42 CE2# CE2# CAD10 19 A16 A16 CCLK 43 VS1# VS1# CVS1 20 A15 A15 CIRDY# 44 RUF IORD# CAD13 21 A12 A12 CCBE2# 45 RFU IOWR# CAD15 22 A7 A7 CAD18 46 A17 A17 CAD16 23 A6 A6 CAD20 47 A18 A18 RFU PC Card Port 44 16-bit PC Card Interface CardBus Pin Memory-Only I/O & Memory 48 A19 A19 CBLOCK# 49 A20 A20 CSTOP# 50 A21 A21 CDEVSEL# 51 VCC VCC VCC 52 VPP2 VPP2 VPP2 53 A22 A22 CTRDY# 54 A23 A23 CFRAME# 55 A24 A24 CAD17 56 A25 A25 CAD19 57 VS2# VS2# CVS2 58 RESET RESET CRST# 59 WAIT# WAIT# CSERR# 60 RFU INPACK# CREQ# 61 REG# REG# CCBE3# 62 BVD2 SPKR# CAUDIO 63 BVD1 STSCHG# CSTSCHG 64 D8 D8 CAD28 65 D9 D9 CAD30 66 D10 D10 CAD31 67 CD2# CD2# CCD2# 68 GND GND GND PC Card Port 45 Hard Drive Port 4 Under ordinary circumstances, it is not necessary to access the hard drive port. The pin locations are listed 1 2 3 4 5 6 7 1 and illustrated below in the event of hard replacement. 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Power Segment Signal Segment Table 4-9. Hard Drive Pin Assignments Signal Segment Pin Number Signal 1 GND 2 A+ 3 A- 4 GND 5 B- 6 B+ 7 GND Description 2nd mate Differential signal pair A from Phy 2nd mate Differential signal pair B from Phy 2nd mate Power Segment Pin Number Signal Description 1 V33 3.3V power 2 V33 3.3V power 3 V33 3.3V power, pre-charge. 2nd mate 4 GND 1st mate 5 GND 2nd mate 6 GND 2nd mate 7 V5 5V power, pre-charge, 2nd mate 8 V5 5V power 9 V5 5V power 10 GND 2nd mate 11 Reserved 12 GND 1st mate 13 V12 12V power, pre-charge, 2nd mate 14 V12 12V power 15 V12 12V power Hard Drive Port 46 RJ-45 LAN Port 4 12345678 Table 4-10. LAN Port Pin Assignments Note: The following table is correct for 10Base-T and 100Base-Tx, but not for 1000Base-T. For 1000Base-T pin assignments, go to one of the following Web sites: http://www.foundrynet.com/services/documentation/EI48G/b_48Gcables.html http://home.cfl.rr.com/bjp/RJ45pins.htm Pin Signal Remarks 1 TX+ Transmit + 2 TX- Transmit - 3 RX+ Receive + 4 NC Not used 5 NC Not used 6 RX- Receive - 7 NC Not used 8 NC Not used IEEE 1394 Port 4 The IEEE 1394 ports on the Tablet PC and the Tablet Dock conform to IEEE 1394 standards. The IEEE 1394 and USB ports on the Tablet Dock are independent ports (i.e., they are not pass-through ports). IEEE 1394 cable characteristics follow: • Suggested maximum cable length: 4.5 meters • 110 ohms characteristic impedance - differential mode • 33 ohms characteristic impedance - common mode • Relative propagation skew < 400ps @ 100 MHz and < 100ps @ 400 MHz (the difference between the differential mode propagation delay of the two twisted pair conductors that must be measured in the frequency domain). • TPA to TPB crosstalk < -26dB (within 1 MHz to 500 MHz range) • Signal velocity equal to or less than 5.05ns/meter • Signal pair attenuation: 100MHz = <2.3dB 200MHz = <3.2dB 400MHz = <5.8dB 1 2 3 4 Table 4-11. IEEE 1394 Connector Pin Assignments Pin Signal 1 TPB- 2 TPB+ 3 TPA- 4 TPA+ Remarks Twisted Pair B - differential signal Twisted Pair A - differential signal RJ-45 LAN Port 47 External Monitor Port SD Card* Interface Table 4-14. SD Card Pin Assignments 5 4 10 15 3 9 14 2 8 1 7 13 12 6 11 Table 4-12. External Monitor Port Pin Assignments Host I/O Pin Signal Remarks 1 CD/DAT3 Card Detect/Data Line (Bit 0) 2 CMD Command/Response 3 VSS1 Ground 4 CDD Supply Voltage 5 CLK Clock 6 VSS2 Ground 7 DAT0 Data Line (Bit 1) 8 DAT1 Data Line (Bit 2 9 DAT2 Data Line (Bit 3 Pin Signal (KB) 1 RED 2 GREEN 3 BLUE 4 NC -- Memory Stick* Interface 5 GND -- Table 4-15. Memory Stick Pin Assignments 6 GND -- 7 GND -- 8 GND -- 9 DDCVCC -- 10 GND -- 11 NC -- 12 DDCDATA 13 HSYNC 14 VSYNC 15 DDCCLK *SDIO card is not supported. Smart Card Interface Pin Signal Remarks 1 VSS 2 BS 3 VCC 4 DIO 5 Reserve 6 INS 7 Reserve 8 SCLK 9 VCC 10 VSS Serial Protocol Bus State Signal Serial Protocol Data Signal Stick On/Off Detection Pin Serial Protocol Lock Signal *Memory Stick PRO™ is not supported. Table 4-13. Smart Card Pin Assignments Pin Signal Remarks C1 Vcc 4.75-5.25V Icc=200mA (max.) C2 RST C3 CLK C4 RFU C5 GND C6 Vpp C7 I/O C8 RFU Reserve Reserve IEEE 1394 Port 48 Chapter 5 System Power This chapter covers the Stylistic ST5100 Tablet PC’s system power hardware, power management states, and state transitions. System Power Hardware 5 The Stylistic ST5100 Tablet PC uses components designed for low power consumption in mobile applications. DC power, whether supplied by the battery pack or an external source, is regulated to different voltage levels required to power various components in the system. Battery Pack 5 When the system is not connected to external power, system power is provided by the battery pack. When an external DC power source is connected to the Tablet PC, the battery pack is gradually charged and the system is powered by the external source. The battery pack can also be removed from the Tablet PC and charged in an external charger. A bridge battery built into the Tablet PC powers the system in suspend mode for approximately 5 minutes while the battery pack is removed. Note: Do not remove the battery pack while the system is running unless an AC Adapter is connected. Suspend system operation or shut down the system before removing the battery pack. The bridge battery will not power the system in the Fully On state. The Tablet PC is equipped with a microcontroller, called the power management microcontroller unit (PMU), which is dedicated to managing battery pack power. The battery pack charge is monitored by the PMU. The PMU determines the percent of charge remaining in the battery pack, controls the battery level, and supplies battery status information to the system through a dedicated interface. A low voltage level detect circuit (independent of the PMU) measures the battery pack voltage level to determine whether the battery pack voltage has dropped to the critically low level (the critically low voltage varies depending on total current draw). When the system is running and the critically low voltage level is reached, the circuit forces the system into Suspend mode and the battery level LED indicates the critically low condition. When the system is forced into Suspend mode by a critically low battery, the system is powered by the remaining charge in the battery pack or the bridge battery (whichever has the highest voltage). In this mode, the Suspend/ Resume button is disabled and system operation cannot be resumed until either an external DC power source is connected or a battery pack with adequate charge is installed. 49 DC Power Inputs 5 External DC power can be connected at two locations on the Tablet PC: • DC power connector on the Tablet PC • System interface connector (via Tablet Dock) A DC power source connected to any of these inputs must provide 3.75 amps at a continuous DC voltage of 16 volts ±10%. Specifications for the DC input connectors on the Tablet PC and Tablet Dock are given below. Table 5-1. DC Input Connectors Connector type EIAJ RC-5320A Type 5 Connector vendor Hosiden Vendor part number* HEC3900-01-010 Pin assignments Center conductor: +16 VDC ±10% Sleeve: ground * This is the part number for the female DC input connector on the Tablet PC and the Tablet Dock. System Power Hardware 50 Chapter 6 Installing Hardware Options This chapter provides procedures for installing DIMM cards, the WLAN device, and the internal IDE hard drive. Installing/Removing a DIMM Module 6 There are two DIMM slots in your Tablet PC. 256 MB, 512 MB, 1 GB and 2 GB modules are available, so you can install a combination of up to 4 GB in the system. DIMM replacement should only be performed at a static-free workstation. Avoid touching connector pins, circuit boards, or other circuit components on the drive or Tablet PC. Electrostatic discharge caused by doing so can damage sensitive components. Installing a Memory Module 6 To install a DIMM module in the Tablet PC: 1. Ensure that the Tablet PC is off. To do so, carry out the Shut Down command in the Start menu. (Do not attempt to remove or install a DIMM module when the system is in Suspend mode or running.) 2. Remove the battery pack and store in a safe place. 3. Remove the three screws from the cover plate on the back of the Tablet PC and remove the cover plate as shown in Figure 6-1 Figure 6-1 Accessing the Memory Slot 4. Insert the DIMM module in the socket at an angle and push it down until it locks into place as shown in Figure 6-2 Note that the DIMM module is keyed to prevent it from being inserted backwards. 51 Figure 6-2 Installing a DIMM Module 5. Reinstall the cover and screws that you removed in step 2. 6. Reinstall the battery pack. 7. Confirm that the DIMM module is recognized by the system. To do so, run BIOS Setup. The size of the DIMM module should be displayed in the Info menu in BIOS Setup. The DIMM module is installed in the Tablet PC and you can now use the system. Removing a Memory Module 6 To remove a DIMM module: 1. Ensure that the Tablet PC is off. To do so, carry out the Shut Down command in the Start menu. (Do not attempt to remove or install a DIMM module when the system is in Suspend mode or running.) 2. Remove the battery pack and store in a safe place. 3. Remove the screws from the cover plate on the back of the Tablet PC and remove the cover plate as shown in Figure 6-1 4. Spread the fingers on the socket that lock the DIMM module in place until the DIMM module is loose. Figure 6-3 Removing a DIMM Module 5. Remove the DIMM module from the socket. 6. Reinstall the battery pack. The DIMM module is now removed from the Tablet PC. Refer to “Installing a Memory Module” on page 51 to install a new DIMM module. Installing/Removing a DIMM Module 52 Replacing/Installing a Wireless LAN Module 6 Wireless LAN Module replacement should only be performed at a static-free workstation. Avoid touching connector pins, circuit boards, or other circuit components on the module or Tablet PC. Electrostatic discharge caused by doing so can damage sensitive components. Removing a Wireless LAN Module 6 Note that the antenna module is installed only if the system was purchased with a Wireless LAN device installed. 1. Remove the four screws (three small and one large) holding the large Wireless LAN Module/hard disk drive cover (adjacent to the memory compartment). Slide the cover away from the system to disengage it from its slots. Set the cover aside for later reinstallation. 2.Carefully disconnect the small connector from the Antenna Module (Figure 6-4). Be careful not to damage the small jumper wire that connects the module with the Wireless LAN Module. 3.Carefully unplug the small cable connector (Figure 6-4) from the Wireless LAN Module. 4.Press the two card latches that hold the Wireless LAN Module away from the module to disengage the module from the latches. The back of the module will pop up when it is disengaged. 5.Once the module is disengaged, pull it carefully from the card connector. Antenna module connector WLAN card latches Screw location Hard drive (inside case) Screw location Hard drive cable Cable connector Hard drive connector WLAN Module Screw location Memory compartment Screw location Figure 6-4 Wireless LAN / Hard Drive Compartment Replacing/Installing a Wireless LAN Module 53 Installing a Wireless LAN Module 6 To install a new Wireless LAN Module, follow the instructions in “Removing a Wireless LAN Module” on page 53, in reverse order. Replacing the IDE Hard Drive 6 The internal IDE hard drive in the Stylistic ST5100 Tablet PC can be removed and replaced, if necessary. • Do not attempt to disassemble or modify the hard drive. • Do not remove any labels from the hard drive. • Hard drive replacement should only be performed at a static-free workstation. Avoid touching connector pins and circuit boards on the drive or Tablet PC. Electrostatic discharge caused by doing so can damage sensitive components. Removing the Hard Drive 6 To remove the hard drive from the Tablet PC, reference Figure 6-4. 1. Close all applications and shut down the system completely. 2. Using a Phillips screw driver, remove the four screws in the WLAN/hard drive cover plate (see Figure 6-4 for location). Slide the cover plate slightly towards the edge of the system to disengage it. Remove the cover. 3. Lift the aluminum case holding the hard drive by the end without the connector until it is at approximately a 45 degree angle from the system. 4. Carefully disconnect the small hard drive connector by pulling it away from the drive. Use care when disconnecting this connector; it is attached to a delicate flex cable. Do not pull the tab on the flex cable connector when lifting the drive. Doing so could damage the flex cable; it is fragile. 5. Lift the drive case out of the system, and slide the drive out of the aluminum case. 6. Once the hard drive has been removed from the Tablet PC, you can install a new hard drive. If you are returning the hard drive for repair, ensure that the packaging material will protect the drive sufficiently during shipment. Installing the Hard Drive 6 To install the hard drive, follow the steps contained in the section entitled “Removing the Hard Drive” in reverse order. Use care when installing the drive to prevent damage to the flex cable. The hard drive is now installed in the Tablet PC. Replacing the IDE Hard Drive 54 Appendix A AT Command Set This Appendix contains a summary of AT commands used by the Stylistic ST5100 Tablet PC’s modem. There are several things to note about this set of commands: • Commands should be entered as ASCII characters. • Commands should begin with “AT”, with a description of the character after the “AT”. • The commands are not case-sensitive; upper and lower case characters are treated the same. • All commands should be followed by the “CR” character stored in “S3”. • Spaces are counted as characters. • Command indication can be a selected letter or number message, or it can be no return message by designation. • Data format is as follows: Start bit Data bit Parity Stop bit 1 7 even 1 1 7 odd 1 1 7 none 2 1 8 none 1 Note: Baud rate and data format are detected by the “AT” character. 55 AT Commands Table 6 AT Data Commands 6 The shaded portion of the table are stored with the AT&W command. Command Specification A/ Repeat last command. A Answer command. D Dial H I L M 3 T 123456789*0#ABCD P 1234567890 W Wait for dial tone. Modem waits for a second dial tone before processing the dial string. @ Wait for quiet answer. ‘ Pause for a time specified by S8 before dialing. ! Hook flash ; Return to command mode after processing command. S=n E Default Dial a telephone number previously stored using the &Zn=x command. The range of n is 0-3. 0 Disables echo to the computer 1 Enables echo to the computer 3 0 Modem goes on-hook 3 1 Modem goes off-hook 0 Returns modem identity string and driver version number, same as I3 1 Calculates ROM checksum and displays it on the DTE. 2 Performs a ROM check and calculates and verifies the checksum, displaying OK or ERROR. 3 Returns modem identity string and driver version number, same as I0 0 Selects low volume. 1 Selects low volume. 2 Selects medium volume. 3 Selects high volume. 0 The speaker is off. 1 The speaker is on until the modem detects the carrier signal. 2 The speaker is always on when modem is off-hook. 3 The speaker is on until the carrier is detected, except while dialing. 3 AT Commands Table 3 56 Command N O When originating or answering, this is for handshake only at the communication standard specified by S7 and the ATB command. 1 When originating or answering, begin the handshake only at the communication standard specified by S7 and the ATB command. During handshake, fallback to a lower speed may occur. 0 Instructs the modem to exit online command mode and return to data mode (see AT Escape Sequence, +++). Enables modem to send result codes to the computer. 1 Disables modem from sending result codes to the computer. Select Tone Dialing. 0 Displays results codes as digits. 1 Displays results codes as text. Result Code No Dial tone Busy Code 0 After S6 Displays “CONNECT” Not displays Not displays 1 After S6 Displays “CONNECTXXX” Not displays Not displays 2 Wait Dial Tone (S6) Displays “CONNECTXXX” Displays Not displays 3 After S6 Displays “CONNECTXXX” Not displays Displays 4 Wait Dial Tone (S6) Displays “CONNECTXXX” Displays Displays Z 3 Reset and recall stored user profile. 0 State of the carrier from remote modem is ignored. DCD circuit is always on. 1 DCD turns on when the remote modem’s carrier signal is detected, and off when the carrier signal is not detected. 0 Ignores status of DTR signal. 1 Enters command state upon On-to-Off transition of DTR. 2 Goes on hook upon On-to-Off transition of DTR. 3 Goes on hook and resets upon On-to-Off transition of DTR. &F &K 3 Result Code Selection and Call Progress Monitoring Dialing &D 3 0 X &C 3 Select Pulse Dialing. T V Default 0 P Q Specification 3 3 Recall factory setting as active configuration. 0 Disable flow control. 3 Enable RTS/CTS (hardware) flow control. 4 Enable XON/XOFF flow control. 3 AT Commands Table 57 Command &P &S &T Specification 0 39% make/break ratio. 10PPS 1 33% make/break ratio. 10PPS 2 33% make/break ratio. 20PPS 0 DSR always ON. 1 DSR comes on when establishing a connection and goes off when the connection ends. 0 Abort. Stops any test in progress. 1 Local analog loop. &V View active configuration and stored profile. &W Store current configuration &Zn Store telephone number. (n=0, 1, 2, 3) /A 3 3 0 Sets MNP block size max. 64 characters 1 Sets MNP block size max. 128 characters 2 Sets MNP block size max. 192 characters 3 Sets MNP block size max. 256 characters 3 Transmit break to remote. /B1-/B9 break length in 100ms units. 3 /Bn /K Default 1) Receives break from the DTE when on-line mode. 5 0, 2, 4 Enter on-line command mode, no break set to remote. 1 Clear data buffers and send break to remote modem 3 Send break to remote modem immediately. 5 Send break to remote modem in sequence with transmitted data. 2) On-line command mode during a data connection. The /B is received in order to send a break to the remote. 0, 1 Clear data buffers and send break to remote modem. 2, 3 Send break to remote modem immediately. 4, 5 Send break to remote modem in sequence with data. 3) Break is received from a remote modem during on-line mode. 0, 1 Clears data buffers and sends break to the DTE. 2, 3 Send a break immediately to the DTE. 4, 5 Send a break in sequence with received data to the DTE. AT Commands Table 58 Command /N /V /X Specification Default 0 Normal speed-buffered mode. 1 Direct mode (if parallel I/F is selected, same as /NO). 2 MNP reliable mode (MNP -> disconnect) 3 Auto-reliable mode (LAPM -> MNP -> NORMAL -> disconnect). Same as /N5. 4 LAPM-reliable mode (LAPM -> disconnect) 5 Auto-reliable mode (LAPM -> MNP -> NORMAL -> disconnect). Same as /N3. 0 Disable protocol result code appended to DCE speed. 1 Enable protocol result code appended to DCE speed. 2 Same as /V1. 0 Do not pass XON/XOFF flow control characters. 1 Pass XON/XOFF flow control characters. -V90= =0 Disable V.90 =1 Enable V.90 Auto Rate =2 Attempt to connect at 28000 bit/s =3 Attempt to connect at 29333 bit/s =4 Attempt to connect at 30666 bit/s =5 Attempt to connect at 32000 bit/s =6 Attempt to connect at 33333 bit/s =7 Attempt to connect at 34666 bit/s =8 Attempt to connect at 36000 bit/s =9 Attempt to connect at 37333 bit/s =10 Attempt to connect at 38666 bit/s =11 Attempt to connect at 40000 bit/s =12 Attempt to connect at 41333 bit/s =13 Attempt to connect at 42666 bit/s =14 Attempt to connect at 44000 bit/s =15 Attempt to connect at 45333 bit/s =16 Attempt to connect at 46666 bit/s =17 Attempt to connect at 48000 bit/s =18 Attempt to connect at 49333 bit/s =19 Attempt to connect at 50666 bit/s =20 Attempt to connect at 52000 bit/s 3 3 3 3 AT Commands Table 59 Command %C %E Specification =21 Attempt to connect at 53333bit/s =? Shows the current value. ? Shows the range [0-21] 0 V.42bis/MNP5 disable. No data compression. 1 V.42bis/MNP5 enable. Data compression enabled. 0 Disable line quality monitor and auto-retrain. 1 Enable line quality monitor and auto-retrain. 2 Enable line quality monitor and fall back/fall forward. Default 3 3 AT Commands Table 60 AT Fax (Class1) Commands 6 Command +FCLASS Specification Default ? Service class indication (*1) =n Service class selection (*2) =? Service class capabilities (*2) +FTS =n Transmission silence (n=0-255, 10ms intervals) +FRS =n Receive silence. (n=0-255, 10ms intervals) +FTM =n Transmit FAX data with carrier. =? Transmit FAX modulation. (*3) =n Receive FAX with carrier. =? Receive FAX modulation. (*3) =n Transmit HDLC data with carrier. =? Transmit HDLC data modulation (*3). =n Receive HDLC data with carrier. =? Receive HDLC data modulation. (*3). +FRM +FTH +FRH *1: 000 -> Data mode 3 *2: 0 -> Data mode 001 -> Facsimile Class 1 1 -> Facsimile Class 1 008 -> Voice Mode 8 -> Voice Mode 080 -> VoiceView Mode (not supported) 80 -> VoiceView Mode (not supported) *3: Modulation by parameter 3: V.21 Channel2 300bps 24: V.27ter 2400bps 48: V.27ter 4800bps 72: V.29 7200bps 73: V.17 7200bps (long 74: V.17 7200bps (short) 96: V.29 9600bps 97: V.17 9600bps (long 98: V.17 9600bps (short) 121: V.17 12000bps (long) 122: V.17 12000bps (short) 145: V.17 14400bps (long) 146: V.17 14400bps (short) AT Commands Table 61 V.25ter AT Commands 6 Command Specification Description +GMI Return ‘Lucent Data/Fax’ Manufacturer Identification +GMR Return Lucent driver version number (e.g., 5.54) Version/Revision Information +GMM Return ‘H.324 video-ready rev. 1.0’ Modem Identification AT+A8E= v8o v8a v8cf 1: The default value disables the CI origination option while in V.8 negotiation. However, the modem, when initiating the call as a data call, detects ANSam and is capable of starting in V.34 mode. 6: Enables DCE control of V.8 and CI option. 1: The default value disables the CI option while in V.8 negotiation. However, the modem, when answering a call, sends the ANSam and is capable of starting in V.34 mode. 5: Enables DCE control of V.8 and CI option. 21h: c1h: Defined for two conditions: as a parameter to configure V.8 originating and answering operation while the DCE is on-hook.It initiates an action if the DCE is off-hook. If enabled, V.8 negotiation does not preclude simultaneous implementation of other negotiation means like V.8bis, V.18, or V.32bis. Call function for H.324 calls. Call function for DSVD calls. AT+A8E? Report current values of subparameter. AT+A8E=? Report supported ranges of values , , +A8I: This indication is used by an answering DCE if +A8E, !=0, to indicate detection of a V.8 CI signal, and report the recovered Call Function octet(s). Value is a hexadecimal code octet that can take values as shown above in +A8E command. +A8M= +A8A: Refer to V.8 document for coding. 1: 0: Directs the DCE to send a V.8 CM or JM signal using the specified hexadecimal coded string. Indicates V.8 ANSam signal flags. Indicates no ANSam signal detected. AT Commands Table 62 S Register Table 6 Default is North America. The shaded portions of the table are stored with AT&W command. Reg * S0 Function Units Auto answer ring number Rings Default 000 Range 000-255 *JP000-015 S1 Ring counter. Read only. Rings 000 000-255 S2 Escape character ASCII 043 000-128 * * S3 Carriage return character (CR) ASCII 013 000-127 * * S4 Line feed character (LF) ASCII 010 000-127 * * S5 Backspace character (BS) ASCII 008 000-032 * S6 Wait time for dial tone. sec 002 002-065 *JP 004 * S7 Wait time for dial tone. sec 050 *JP004-065 001-255 *JP035-059 * S8 Pause for dial delay modifier “,”. sec 002 002-065 * S10 Carrier loss Disconnect time. 100ms 020 001-255 * S11 DTMF Dialing speed. 1ms 095 050-150 *JP70-150 S12 Escape prompt delay. S14 General bit mapped options status. (Read only) S21 20ms 050 0: Enable short form result codes ATV0 1: Enable long form result codes. ATV1 3 0: 10PPS AT&P0, &P1 3 1: 20PPS AT&P2 000-255 Bit 3 Bit 6 General bit mapped options status (Read only) 0: DTR behavior. AT&D0 1: DTR behavior. AT&D1 2: DTR behavior. AT&D2 3: DTR behavior. AT&D3 0: DCD behavior. 1: DCD behavior. Bits 4, 3 3 Bit 5 S Register Table 63 “*” : These S-registers are country-specific. “**” : These return to default value by &W command “*JP” : Default for Japan mode S22 Results bit mapped options status (Read only) 0: Displays “CONNECT” ATX0 4: Displays “CONNECT xxx” ATX1 5: ATX1 mode + dial tone detection ATX2 6: ATX1 mode + busy tone detection ATX3 7: ATX1 mode + dial & busy tone detection ATX4 3 0: 33% Make/Break ratio AT&P1, &P2 3 Bit 7 1: 39% Make/Break ratio AT&P0 010 000, 005-065 S24 Timer to control sleep mode. 000 = disable S37 Dial line rate. =0 Maximum modem speed =1 Reserved =2 1200 bits/s and 75 bits/s =3 300 bits/s =4 Reserved =5 1200 bits/s =6 2400 bits/s =7 4800 bits/s =8 7200 bits/s =9 9600 bits/s =10 12000 bits/s =11 14400 bits/s =12 16800 bits/s =13 19200 bits/s =14 21600 bits/s =15 24000 bits/s =16 26400 bits/s =17 28800 bits/s =18 31200 bits/s =19 33600 bits/s Bits 6-4 sec 3 S Register Table 64 S38 S91 56K Dial Line Rate =0 56K disabled =1 56K enabled - automatic speed selection - maximum modem speed. =2 32000 bits/s =3 34000 bits/s =4 36000 bits/s =5 38000 bits/s =6 40000 bits/s =7 42000 bits/s =8 44000 bits/s =9 46000 bits/s =10 48000 bits/s =11 50000 bits/s =12 52000 bits/s =13 54000 bits/s =14 56000 bits/s Line Transmit Level. This register is effective only for Japan. 3 -dBm 14 S Register Table 9-15 65 Result Codes Summary Result Code 6 Numeric Description OK 0 Command executed. CONNECT 1 Modem connected to line. RING 2 A ring signal has been detected. NO CARRIER 3 Modem lost carrier signal, or does not detect carrier signal, or does not detect answer tone. ERROR 4 Invalid command. NO DIAL TONE 6 No dial tone detected. BUSY 7 Busy signal detected. NO ANSWER 8 No quiet answer. CONNECT 2400 EC* 10 Connection at 2400 bits/s. CONNECT 4800 EC* 11 Connection at 4800 bits/s. CONNECT 9600 EC* 12 Connection at 9600 bits/s. CONNECT 14400 EC* 13 Connection at 14400 bits/s. CONNECT 19200 EC* 14 Connection at 19200 bits/s. CONNECT 7200 EC* 24 Connection at 7200 bits/s. CONNECT 12000 EC* 25 Connection at 12000 bits/s. CONNECT 16800 EC* 86 Connection at 16800 bits/s. CONNECT 300 EC* 40 Connection at 300 bits/s. CONNECT 21600 EC* 55 Connection at 21600 bits/s. CONNECT 24000 EC* 56 Connection at 24000 bits/s. CONNECT 26400 EC* 57 Connection at 26400 bits/s. CONNECT 28800 EC* 58 Connection at 28800 bits/s. CONNECT 31200 EC* 59 Connection at 31200 bits/s. CONNECT 33600 EC* 60 Connection at 33600 bits/s. CONNECT 38400 EC* 28 Connection at 38400 bits/s. (DTE rate) CONNECT 57600 EC* 18 Connection at 57600 bits/s. (DTE rate) CONNECT 115200 EC* 87 Connection at 115200 bits/s. (DTE rate) DELAYED 88 Delay is in effect for the dialed number. BLACKLISTED 89 Dialed number is blacklisted. BLACKLIST FULL 90 Blacklist is full. CONNECT 32000 EC* 70 Connection at 32000 bits/s. (K56flex or V.90 mode) CONNECT 34000 EC* 71 Connection at 34000 bits/s. (K56flex mode) CONNECT 03600 EC* 72 Connection at 36000 bits/s. (K56flex or V.90 mode) Result Codes Summary 66 Result Code Numeric Description CONNECT 38000 EC* 73 Connection at 38000 bits/s. (K56flex mode) CONNECT 40000 EC* 74 Connection at 40000 bits/s. (K56flex or V.90 mode) CONNECT 42000 EC* 75 Connection at 42000 bits/s. (K56flex mode) CONNECT 44000 EC* 76 Connection at 44000 bits/s. (K56flex or V.90 mode) CONNECT 46000 EC* 77 Connection at 46000 bits/s. (K56flex mode) CONNECT 48000 EC* 78 Connection at 48000 bits/s. (K56flex or V.90 mode) CONNECT 50000 EC* 79 Connection at 50000 bits/s. (K56flex mode) CONNECT 52000 EC* 80 Connection at 52000 bits/s. (K56flex or V.90 mode) CONNECT 54000 EC* 81 Connection at 54000 bits/s. (K56flex mode) CONNECT 56000 EC* 82 Connection at 56000 bits/s. (K56flex mode) CONNECT 28000 EC* 100 Connection at 28000 bits/s. (V.90 mode) CONNECT 29333 EC* 101 Connection at 29333 bits/s. (V.90 mode) CONNECT 30666 EC* 102 Connection at 30666 bits/s. (V.90 mode) CONNECT 33333 EC* 103 Connection at 33333 bits/s. (V.90 mode) CONNECT 34666 EC* 104 Connection at 34666 bits/s. (V.90 mode) CONNECT 37333 EC* 105 Connection at 37333 bits/s. (V.90 mode) CONNECT 38666 EC* 106 Connection at 38666 bits/s. (V.90 mode) CONNECT 41333 EC* 107 Connection at 41333 bits/s. (V.90 mode) CONNECT 42666 EC* 108 Connection at 42666 bits/s. (V.90 mode) CONNECT 45333 EC* 109 Connection at 45333 bits/s. (V.90 mode) CONNECT 46666 EC* 110 Connection at 46666 bits/s. (V.90 mode) CONNECT 49333 EC* 111 Connection at 49333 bits/s. (V.90 mode) CONNECT 50666 EC* 112 Connection at 50666 bits/s. (V.90 mode) CONNECT 53333 EC* 113 Connection at 53333 bits/s. (V.90 mode) CONNECT 54666 EC* 114 Connection at 54666 bits/s. (V.90 mode) * EC only appears when the extended result code configuration option is enabled. EC is replaced by one of the following symbols, depending upon the error control method used: V42bis -> V.42 error control and V.42bis data compression. V42 -> V.42 error control only. MNP5 -> MNP class 4 error control and MNP class 5 data compression. MNP4 -> MNP class 4 error control only. Neck -> No error control protocol. Note: In “Normal mode”, connection speed is up to 31200bps. Result Codes Summary 67 Appendix B Agency Notices NOTICE Changes or modifications not expressly approved by Fujitsu could void this user’s authority to operate the equipment. FCC NOTICES Notice to Users of Radios and Television These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet that is on a different circuit than the receiver. • Consult the dealer or an experienced radio/TV technician for help. Shielded interconnect cables must be employed with this equipment to ensure compliance with the pertinent RF emission limits governing this device. Notice to Users of the US Telephone Network Your Tablet PC may be supplied with an internal modem which complies with Part 68 of the FCC rules. On the system is a label that contains the FCC Registration Number and the Ringer Equivalence Number (REN) for this equipment among other information. If requested, the user must provide their telephone company with the following information: 1. The telephone number to which the computer is connected. 2. The Ringer Equivalence Number (REN) for this equipment. 3. The equipment requires a standard modular jack type USOC RJ-11C which is FCC Part 68 compliant. 4. The FCC Registration Number. This equipment is designed to be connected to the telephone network or premises wiring using a standard modular jack type USOC RJ-11C which is FCC Part 68 compliant and a line cord between the modem and the telephone network with a minimum of 26AWG. NOTICE: The Ringer Equivalence Number (REN) for this terminal equipment is 0.1B. The REN is used to determine the number of devices that you may connect to your telephone line and still have all of those devices ring when your number is called. Too many devices on one line may result in failure to ring in response to an incoming call. In most, but not all, areas the sum of the RENs of all of the devices should not exceed five (5). To be certain of the number of devices you may connect to your line, as determined by the RENs, contact your local telephone company. If this equipment causes harm to the telephone network, your telephone company may discontinue your service temporarily. If possible, they will notify you in advance. If advance notice is not practical they will notify you as soon as possible. You will also be advised of your right to file a complaint with the FCC. This fax modem also complies with fax branding requirements per FCC Part 68. Your telephone company will probably ask you to disconnect this equipment from the telephone network until the problem is corrected and you are sure that the equipment is not malfunctioning. This equipment may not be used on coin-operated telephones provided by your telephone company. Connection to party lines is subject to state tariffs. Contact your state’s public utility commission, public service commission or corporation commission for more information. This equipment includes automatic dialing capability. When programming and/or making test calls to emergency numbers: • Remain on the line and briefly explain to the dispatcher the reason for the call. • Perform such activities in off-peak hours, such as early morning or late evening. FCC rules prohibit the use of non-hearing aid compatible telephones in the following locations or applications: • All public or semi-public coin-operated or credit card telephones. • Elevators, highways, tunnels (automobile, subway, railroad or pedestrian) where a person with impaired hearing might be isolated 68 in an emergency. • Places where telephones are specifically installed to alert emergency authorities such as fire, police or medical assistance personnel. • Hospital rooms, residential health care facilities, convalescent homes and prisons. • Stores where telephones are used by patrons to order merchandise. • Public transportation terminals where telephones are used to call taxis or to reserve lodging or rental cars. • In hotel and motel rooms as at least ten percent of the rooms must contain hearing aid-compatible telephones or jacks for plug-in hearing aid compatible telephones which will be provided to hearing impaired customers on request. DOC (INDUSTRY CANADA) NOTICES Notice to Users of Radios and Television This Class B digital apparatus meets all requirements of Canadian Interference-Causing Equipment Regulations. CET appareil numérique de la class B respecte toutes les exigence du Réglement sur le matérial brouilleur du Canada. Notice to Users of the Canadian Telephone Network NOTICE: This equipment meets the applicable Industry Canada Terminal Equipment Technical Specifications. This is confirmed by the registration number. The abbreviation, IC, before the registration number signifies that registration was performed based on a Declaration of Conformity indicating that Industry Canada technical specifications were met. It does not imply that Industry Canada approved the equipment. Before connecting this equipment to a telephone line the user should ensure that it is permissible to connect this equipment to the local telecommunication facilities. The user should be aware that compliance with the certification standards does not prevent service degradation in some situations. Repairs to telecommunication equipment should be made by a Canadian authorized maintenance facility. Any repairs or alterations not expressly approved by Fujitsu or any equipment failures may give the telecommunication company cause to request the user to disconnect the equipment from the telephone line. NOTICE: The Ringer Equivalence Number (REN) for this terminal equipment is 0.1B. The REN assigned to each terminal equipment provides an indication of the maximum number of terminals allowed to be connected to a telephone interface. The termination on an interface may consist of any combination of devices subject only to the requirement that the sum of the Ringer Equivalence Numbers of all the devices does not exceed five. For safety, ensure that the electrical ground of the power utility, the telephone lines and the metallic water pipes are connected together. Do NOT attempt to make such connections; rather, contact the appropriate electric inspection authority or electrician. This may be particularly important in rural areas. Avis Aux Utilisateurs Du Réseau Téléphonique Canadien AVIS: Le présent matériel est conforme aux spécifications techniques d’Industrie Canada applicables au matériel terminal. Cette conformité est confirmée par le numéro d’enregistrement. Le sigle IC, placé devant le numéro d’enregistrement, signifie que l’enregistrement s’est effectué conformément à une déclaration de conformité et indique que les spécifications techniques d’Industrie Canada ont été respectées. Il n’implique pas qu’Industrie Canada a approuvé le matériel. Avant de connecter cet équipement à une ligne téléphonique, l’utilisateur doit vérifier s’il est permis de connecter cet équipement aux installations de télécommunications locales. L’utilisateur est averti que même la conformité aux normes de certification ne peut dans certains cas empêcher la dégradation du service. Les réparations de l’équipement de télécommunications doivent être eVectuées par un service de maintenance agréé au Canada. Toute réparation ou modification, qui n’est pas expressément approuvée par Fujitsu, ou toute défaillance de l’équipement peut entraîner la compagnie de télécommunications à exiger que l’utilisateur déconnecte l’équipement de la ligne téléphonique. AVIS: L’indice d’équivalence de la sonnerie (IES) du présent matériel est de 0.1B. L’IES assigné à chaque dispositif terminal indique le nombre maximal de terminaux qui peuvent être raccordés à une interface téléphonique. La terminaison d’une interface peut consister en une combinaison quelconque de dispositifs, à la seule condition que la somme d’indices d’équivalence de la sonnerie de tous les dispositifs n’excède pas 5. Pour assurer la sécurité, les utilisateurs doivent vérifier que la prise de terre du service d’électricité, les lignes télphoniques et les conduites d’eau métalliques sont connectées ensemble. Les utilisateurs NE doivent PAS tenter d’établir ces connexions eux-mêmes, mais doivent contacter les services d’inspection d’installations électriques appropriés ou un électricien. Ceci peut être particulièrement important en régions rurales. 69 Wireless LAN Agency Notices 6 FCC REGULATORY INFORMATION Please note the following regulatory information related to the optional wireless LAN module. Regulatory Notes and Statements Wireless LAN, Health and Authorization for use Radio frequency electromagnetic energy is emitted from Wireless LAN devices. The energy levels of these emissions, however, are much less than the electromagnetic energy emissions from wireless devices such as mobile phones. Wireless LAN devices are safe for use by consumers because they operate within the guidelines found in radio frequency safety standards and recommendations. The use of Wireless LAN devices may be restricted in some situations or environments, such as: • On board an airplane, or • In an explosive environment, or • In situations where the interference risk to other devices or services is perceived or identified as harmful. In cases in which the policy regarding use of Wireless LAN devices in specific environments is not clear (e.g., airports, hospitals, chemical/oil/gas industrial plants, private buildings), obtain authorization to use these devices prior to operating the equipment. Regulatory Information/Disclaimers Installation and use of this Wireless LAN device must be in strict accordance with the instructions included in the user documentation provided with the product. Any changes or modifications made to this device that are not expressly approved by the manufacturer may void the user’s authority to operate the equipment. The manufacturer is not responsible for any radio or television interference caused by unauthorized modification of this device, or the substitution or attachment of connecting cables and equipment other than those specified by the manufacturer. It is the responsibility of the user to correct any interference caused by such unauthorized modification, substitution or attachment. The manufacturer and its authorized resellers or distributors will assume no liability for any damage or violation of government regulations arising from failure to comply with these guidelines. This device must not be co-located or operating in conjunction with any other antenna or transmitter. For Atheros Wireless LAN: For operation within 5.15~5.25GHz frequency range, it is restricted to indoor environment, and the antenna of this device must be integral. Federal Communications Commission statement This device complies with Part 15 of FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause interference, and, (2) This device must accept any interference, including interference that may cause undesired operation of this device. FCC Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy. If not installed and used in accordance with the instructions, it may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try and correct the interference by one or more of the following measures: 1. 2. 3. 4. Reorient or relocate the receiving antenna. Increase the distance between the equipment and the receiver. Connect the equipment to an outlet on a circuit different from the one the receiver is connected to. Consult the dealer or an experienced radio/TV technician for help. FCC Radio Frequency Exposure statement The available scientific evidence does not show that any health problems are associated with using low power wireless devices. There is no proof, however, that these low power wireless devices are absolutely safe. Low power wireless devices emit low levels of radio frequency energy (RF) in the microwave range while being used. Whereas high levels of RF can produce health effects (by heating tissue), exposure to low-level RF that does not produce heating effects causes no known adverse health effects. Many studies of low-level RF exposure have not found any biological effects. Some studies have suggested that some biological effects might occur, but such findings have not been confirmed by additional research. The wireless LAN radio device has been tested and found to comply with FCC radiation exposure limits set forth for an uncontrolled equipment and meets the FCC radio frequency (RF) Exposure Guidelines in Supplement C to OET65. Wireless LAN Agency Notices 70 The maximum SAR values measured from the devices are: • Intel PROSet Wireless LAN (WM3945ABG): 1.47 W/kg • Atheros Wireless LAN (AR5BX6): 1.57 W/kg • Intel PROSet Wireless LAN + Bluetooth Simultaneous: 1.47 W/kg • Atheros Wireless LAN + Bluetooth Simultaneous: 1.56 W/kg Export restrictions This product or software contains encryption code which may not be exported or transferred from the US or Canada without an approved US Department of Commerce export license. This device complies with Part 15 of FCC Rules., as well as ICES 003 B / NMB 003 B. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesirable operation. Modifications not expressly authorized by Fujitsu Computer Systems Corporation may invalidate the user's right to operate this equipment. Canadian Notice To prevent radio interference to the licensed service, this device is intended to be operated indoors and away from windows to provide maximum shielding. Equipment (or its transmit antenna) that is installed outdoors is subject to licensing. High-power radars are allocated as the primary users of 5250 - 5350 MHz and 5650 - 5850 MHz, and these radars could cause interference and/or damage to LELAN (license exempt LAN) devices operating in these bands. Wireless LAN Agency Notices 71 Index A Info menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 Keyboard Features Submenu Options . . . . . . . . . 13 Main menu options . . . . . . . . . . . . . . . . . . . . . . . . . 9 Owner Information menu . . . . . . . . . . . . . . . . 24, 25 Primary Master submenu . . . . . . . . . . . . . . . . . . . . 10 QuickBoot mode, enabling . . . . . . . . . . . . . . . . . . 26 Security menu options . . . . . . . . . . . . . . . . . . . . . . 21 setup prompt, enabling . . . . . . . . . . . . . . . . . . . . . . 26 starting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 supervisor password, enabling . . . . . . . . . . . . . . . . 21 system date, changing . . . . . . . . . . . . . . . . . . . . . . . . 9 system time, changing . . . . . . . . . . . . . . . . . . . . . . . . 9 using . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 AC adapter, specifications . . . . . . . . . . . . . . . . . . . . . 34 ACPI Specification . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 ACPI, support for . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 agency approval, specifications . . . . . . . . . . . . . . . . . 36 Agency Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68 AT Command Set . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55 AT Commands Table . . . . . . . . . . . . . . . . . . . . . . . . . 56 audio inputs and outputs, enabled and disabled on pen tablet and port replicator . . . . . . . . . . . . . . . . . . . . . . 43 audio jacks, connector, specifications . . . . . . . . . . . . 33 BIOS Setup Utility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 BIOS version, displaying in BIOS Setup . . . . . . . . . . 28 B battery battery pack, charge status . . . . . . . . . . . . . . . . . . . 49 battery pack, system power hardware and power management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49 bridge battery, specifications . . . . . . . . . . . . . . . . . 34 main battery pack, specifications . . . . . . . . . . . . . . 34 sub battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 BIOS Advanced Menu Options . . . . . . . . . . . . . . . . . . . . Boot Device Priority Submenu . . . . . . . . . . . . . . . Boot Menu Options . . . . . . . . . . . . . . . . . . . . . . . . CPU Features Submenu . . . . . . . . . . . . . . . . . . . . . Event Logging Submenu . . . . . . . . . . . . . . . . . . . . Exit Menu Options . . . . . . . . . . . . . . . . . . . . . . . . . Hard Disk Security Submenu . . . . . . . . . . . . . . . . Info Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Internal Device Configurations Submenu . . . . . . Keyboard Features Submenu Options . . . . . . . . . Miscellaneous Configurations Submenu . . . . . . . Owner Information Submenu . . . . . . . . . . . . . . . . Primary Master Submenu Options . . . . . . . . . . . . Security Chip Setting Submenu . . . . . . . . . . . . . . . USB Features Submenu . . . . . . . . . . . . . . . . . . . . . Video Submenu Options . . . . . . . . . . . . . . . . . . . . 11 27 26 16 20 29 23 28 15 13 19 24 10 25 18 14 BIOS settings about . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 BIOS Setup Boot menu options . . . . . . . . . . . . . . . . . . . . . . . . . 26 boot-time diagnostic messages, enabling . . . . . . . 26 display screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Exit menu options . . . . . . . . . . . . . . . . . . . . . . . . . . 29 boot-time diagnostic messages, enabling in BIOS Setup 26 bridge battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 C cache, specifications . . . . . . . . . . . . . . . . . . . . . . . . . . 30 cache, viewing size of in BIOS Setup . . . . . . . . . . . . . 28 connectors DC power input, pin assignments . . . . . . . . . . . . . 37 CPU speed, specifications . . . . . . . . . . . . . . . . . . . . . . 30 CPU speed, viewing in BIOS Setup . . . . . . . . . . . . . . 28 current BIOS settings . . . . . . . . . . . . . . . . . . . . . . . . . . 6 D date, changing in BIOS Setup . . . . . . . . . . . . . . . . . . . . 9 DC power input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . connector, pin assignments . . . . . . . . . . . . . . . . . . connector, specifications . . . . . . . . . . . . . . . . . . . . voltage specifications . . . . . . . . . . . . . . . . . . . . . . . 37 37 50 33 dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 DIMM installing and removing . . . . . . . . . . . . . . . . . . . . . 51 DIMM card, removing . . . . . . . . . . . . . . . . . . . . . . . . 52 DIMM slot, specifications . . . . . . . . . . . . . . . . . . . . . 30 DMI event logging options, BIOS Setup . . . . . . . . . . 20 DMI support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 72 E M environmental, specifications . . . . . . . . . . . . . . . . . . 32 External Monitor Port . . . . . . . . . . . . . . . . . . . . . . . . 48 memory DIMM slot, specifications . . . . . . . . . . . . . . . . . . . .30 video memory, specifications . . . . . . . . . . . . . . . . .30 viewing size of in BIOS Setup . . . . . . . . . . . . . . . . .28 external video . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 memory module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .52 F memory stick . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 exiting BIOS Setup, exit menu options . . . . . . . . . . . 29 Fujitsu Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 H hard disk drive installing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54 internal, replacing . . . . . . . . . . . . . . . . . . . . . . . . . . 54 removing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54 Microsoft Developer’s Network . . . . . . . . . . . . . . . . . .2 Microsoft Windows XP Tablet PC Edition . . . . . . . . .4 O operating systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 organization of manual . . . . . . . . . . . . . . . . . . . . . . . . .1 OS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 hard disk drive port, specifications . . . . . . . . . . . . . . 46 hardware options, installing . . . . . . . . . . . . . . . . . . . . 51 P headphone jack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43 password on boot, BIOS option . . . . . . . . . . . . . . . . .22 humidity, specifications . . . . . . . . . . . . . . . . . . . . . . . 32 passwords, in BIOS Setup . . . . . . . . . . . . . . . . . . . . . .21 I I/O controller, specifications . . . . . . . . . . . . . . . . . . . 30 IEEE 1394 Jack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 IEEE 1394 Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 IEEE 1394 support . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 info menu, in BIOS Setup . . . . . . . . . . . . . . . . . . . . . 28 Infrared support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Installing a Memory Module . . . . . . . . . . . . . . . . . . . 51 installing the hard disk drive . . . . . . . . . . . . . . . . . . . 54 installing the internal hard disk drive . . . . . . . . . . . . 54 Installing/Removing a DIMM Module . . . . . . . . . . . 51 internal LAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 internal LAN/modem . . . . . . . . . . . . . . . . . . . . . . . . . . 3 specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 IrDA port, specifications . . . . . . . . . . . . . . . . . . . 33, 38 IrDA standards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 PC Card PC Card Standards, related documentation . . . . . .2 slots, specifications . . . . . . . . . . . . . . . . . . . . . . . . . .33 support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 PC Card port, specifications . . . . . . . . . . . . . . . . . . . .44 PC2001 design guidelines . . . . . . . . . . . . . . . . . . . . . . . .3 PCIC protocol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 pen support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 peripheral interface, specifications . . . . . . . . . . . . . . .33 peripheral interfaces, on tablet pc . . . . . . . . . . . . . . . .37 permanent BIOS settings . . . . . . . . . . . . . . . . . . . . . . . .6 physical specifications . . . . . . . . . . . . . . . . . . . . . . . . .33 power management power management microcontroller unit (PMU) 49 power system, specifications . . . . . . . . . . . . . . . . . .34 states . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .49 Q QuickBoot mode, enabling in BIOS Setup . . . . . . . . .26 L LAN/modem, internal, See also internal LAN/modem 3 level 1 cache, viewing size of in BIOS Setup . . . . . . . 28 level 2 cache, viewing size of in BIOS Setup . . . . . . . 28 R related documentation . . . . . . . . . . . . . . . . . . . . . . . . . .2 removing a DIMM card . . . . . . . . . . . . . . . . . . . . . . . .52 removing the hard disk drive . . . . . . . . . . . . . . . . . . . .54 Replacing/Installing a Wireless LAN Module . . . . . .53 Result Codes Summary . . . . . . . . . . . . . . . . . . . . . . . .66 RJ-45 LAN Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47 73 S sub battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34 S Register Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63 supervisor password, enabling in BIOS Setup . . . . . .21 SD Card/Memory Stick support . . . . . . . . . . . . . . . . . 4 supported operating systems . . . . . . . . . . . . . . . . . . . . .4 setup prompt, enabling in BIOS setup . . . . . . . . . . . 26 system date, changing in BIOS Setup . . . . . . . . . . . . . .9 Smart Card support . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 system interface port connector type . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33 specifications AC adapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 agency approvals . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 audio controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 battery pack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 Bluetooth Module . . . . . . . . . . . . . . . . . . . . . . . . . . 30 cache . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 Chipset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 Communications Devices . . . . . . . . . . . . . . . . . . . 31 CPU Temperature Monitor . . . . . . . . . . . . . . . . . . 30 DC power input connector . . . . . . . . . . . . . . . . . . 50 DC power input voltage . . . . . . . . . . . . . . . . . . . . . 33 Digitizer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 DIMM slot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 environmental . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 External Video Capabilities . . . . . . . . . . . . . . . . . . 31 Fingerprint Sensor . . . . . . . . . . . . . . . . . . . . . . . . . 30 Front Side Bus (FSB) . . . . . . . . . . . . . . . . . . . . . . . 30 general . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 Hard Disk Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 hard disk drive port . . . . . . . . . . . . . . . . . . . . . . . . 46 humidity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 I/O controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 IEEE 1394 Controller . . . . . . . . . . . . . . . . . . . . . . . 30 infrared keyboard port . . . . . . . . . . . . . . . . . . . . . . 33 Internal modem . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 IrDA Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 IrDA port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33, 38 LAN Controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 PC Card controller . . . . . . . . . . . . . . . . . . . . . . . . . 30 PC Card port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44 peripheral interface . . . . . . . . . . . . . . . . . . . . . . . . . 33 physical . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 power management . . . . . . . . . . . . . . . . . . . . . . . . 34 power system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 processor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 sub battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 tablet dock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 TPM Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 USB Controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 USB port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 video memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 system power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .49 system time, changing in BIOS Setup . . . . . . . . . . . . . .9 T Tablet Dock Interface Port . . . . . . . . . . . . . . . . . . . . . .39 Tablet Dock User’s Guide . . . . . . . . . . . . . . . . . . . . . . .2 tablet dock, specifications . . . . . . . . . . . . . . . . . . . . . .36 Tablet PC features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 temperature, specifications . . . . . . . . . . . . . . . . . . . . .32 time, changing in BIOS Setup . . . . . . . . . . . . . . . . . . . .9 U Universal Serial Bus, specification . . . . . . . . . . . . . . . . .2 USB port, position assignments . . . . . . . . . . . . . . . . .38 USB port, specifications, pen tablet . . . . . . . . . . . . . .33 USB port, specifications, tablet dock . . . . . . . . . . . . .36 USB support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 user password, enabling in BIOS Setup . . . . . . . . . . .21 V video memory, specifications . . . . . . . . . . . . . . . . . . .30 video modes supported for use with external monitor . . . . . . . .31 video, external . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31 W Windows XP Professional Resource Kit . . . . . . . . . . . .2 Stylistic ST5000 User’s Guide . . . . . . . . . . . . . . . . . . . . 2 74 75