Transcript
11/17/03
6:39 PM
Page 1
Printed in the U.S.A.
18890 Plx. HL1_HL2
65688-01 ©10•2003 P l a n t r o n i c s I n c .
www.plantronics.com 800.544.4660 345 Encinal Street Santa Cruz, California 95060 Copyright 2003 Plantronics, Inc. All rights reserved. • This warranty gives you specific legal rights, and you may also have other rights which vary from state to state or province to province. Please contact your dealer or our service center for the full details of our limited warranty, including items not covered by this limited warranty.
User Guide
• THIS IS PLANTRONICS’ COMPLETE WARRANTY FOR THE PRODUCTS. • To obtain service in the U.S. contact Plantronics at (800) 544-4660 and in Canada call (800) 540-8363. If you need additional i nformation, please contact our service centers at the numbers provided. • We will, at our option, repair or replace the Products that do not conform to the warranty. We may use functionally equivalent reconditioned/ refurbished/remanufactured/pre-owned or new Products or parts. • This warranty extends to you only if you are the end user with the original purchase receipt.
Models HL1 & HL2
• This warranty lasts for two years from the date of purchase of the Products. • This warranty covers defects in materials and workmanship of Commercial Products manufactured, sold or certified by Plantronics which were purchased and used in the United States and Canada.
Telephone Handset Lifter Accessory
for Plantronics Commercial Products Purchased in the US and Canada LIMITED WARRANTY
WARRANTY AND SERVICE HL2 DIAGRAM
HL2 TELEPHONE HANDSET LIFTER ACCESSORY
2
A
5
HL1
B
HL1
C
HL2
Snap the Lifter Motor Assembly with the A20 Adapter Housing to the A20 accessory deck.
D
6
2
HL2
HL1 CA10
5
er Pow TALK Talk
Char
ge CHANN
EL
MUTE
VOLU
–
ME
+
A20
4
8
Route the associated wiring for the A20 amplifier through the accessory deck as illustrated in the A20 User Guide. Replace the A20 accessory deck lid and place your telephone on the accessory deck.
D
Move and/or slide the Lifter Arm to a position near the top of the earpiece of the telephone handset. Tighten the adjusting screw firmly with a screw driver or small coin to prevent it from coming loose.
A
You may need to manually readjust the lifter arm to the position shown in D .
1
HL1 Adapter Power Plug
7
HL2 Adapter Housing
2
Lifter Motor Assembly
8
HL2 Adapter Power Plug
Repeat this process until the Lifter can pick up and put down the telephone handset without error.
3
HL1 Expandable Base
9
Adapter Power Line
No other connections are required. The Lifter will be powered directly by the A20 amplifier.
4
HL1 Ringer Detector and cable P/N 46780-01
5
Lifter Arm P/N 46778-01
6
HL1 Lifter Base
9 11
10
Accessory Jack
11
Ringer Detector Jack (only with the HL1 Lifter)
C
Connect the Adapter Power Plug to the aux jack of the A20 amplifier. The aux jack on the A20 amplifier is normally used for the on line Indicator (OLI). If you plan to use the OLI, connect the OLI plug to the Accessory Jack on the back side of the Lifter Motor Assembly .
To test the Lifter, depress the handset/headset selector bar on the A20 amplifier and the Lifter Arm will automatically pick up your handset. Push it again to have the unit return the telephone to its original position.
7
10
HARDWARE SETUP FOR THE A20 TELEPHONE HEADSET AMPLIFIER
3
1
HL2
HL2 TELEPHONE HANDSET LIFTER ACCESSORY
You are now ready to make or receive calls.
LIFTER OPERATION The handset/headset bar on the A20 amplifier will activate the lifter to make or receive a call.
D
Page 2
– ME VOLU
6:39 PM
rge
11/17/03
Cha
18890 Plx. HL1_HL2
+
NEL CHAN MUTE
Talk
TALK
er Pow
CA10
A20
HL1 HL2 D
HL1
B
HL2
C
A
HL1 DIAGRAM
HL1 DIAGRAM
Ringer Detector Jack
9
Accessory Jack
8
Adapter Power Line
7
HL1 Lifter Base
6
Lifter Arm P/N 46778-01
5
HL1 Ringer Detector and cable P/N 46780-01
4
HL1 Expandable Base
3
Lifter Motor Assembly
2
HL1 Adapter Power Plug
1
HL1 DIAGRAM KEY HL1 TELEPHONE HANDSET LIFTER ACCESSORY
HL1 TELEPHONE HANDSET LIFTER ACCESSORY
TROUBLESHOOTING
HARDWARE SETUP
LIFTER OPERATION
I CANNOT HEAR A DIAL TONE
FOR THE CA10 CORDLESS TELEPHONE HEADSET AMPLIFIER
MAKING AND RECEIVING A CALL (Near your telephone)
On the CA10 amplifier, press the talk button on the CA10 base or amplifier remote unit.
Slide the Lifter Motor Assembly into the LHL1 Base until it locks in. Avoid trying to snap it in, it slides in easily.
C
Connect the Adapter Power Plug to the lifter jack on the base of the CA10 Cordless Telephone Headset Amplifier. Loosen the Lifter Arm screw and insert the Lifter Arm into the shaft. Leave the screw untightened for now. Position your telephone on the Lifter Base so that the lifter arm is under the handset, near the earpiece. You may need to manually readjust the lifter arm to the position shown in D . You will hear gear whine during up-down adjustment. This will not hurt the device. Once in place, tighten the lifter arm screw.
A
D
NOTE: When using the speakerphone feature of your phone, turn the ringer off on the CA10 remote. Using the speakerphone will confuse the ring detector. B
On the A20 press the headset/handset Bar. Check that the Adapter Plug and the Ringer Detector Plug are completely engaged in the back side of the Lifter Motor Assembly 2 .
ON THE CA10 AMPLIFIER, I HEAR A RING ON THE TELEPHONE BUT NOT ON THE REMOTE
RECEIVING A CALL (Using the CA10 remote unit away from your telephone)
Press the talk button to hang-up.
Connect the Ring Detector Cable to the Ring Detector Jack located on the back of the Lifter Assembly .
D
When your call is complete, push the talk button again on the CA10 base or remote unit. The lifter will then return the telephone handset to its original position.
The Ring Detector detects a ring from the lifter on your telephone and transmits the ring to the remote unit which rings. When the talk button is pushed (on the remote unit ), a signal is sent to the Lifter which will lift the telephone handset off the telephone. You may now talk to your calling party.
Depress the Talk button on the CA10 base or remote unit and the Lifter will automatically pickup your handset so that you hear a dial tone.
Remove the tape from the Ring Detector Sensor and attach the sensor to a position closest to the telephone ringer/speaker. The Ring Detector Sensor is a little cylindrical microphone located at the end of the Ring Detector Cable .
Put on your headset and depress the talk button on the CA10 base or remote unit. This action activates the lifter to take the telephone handset off the hook.
B
Check that the ringer switch on the CA10 remote unit is set to the “on” position. Check your ring detector plug and ensure it is plugged in to the Ring Detector Jack . Check the location of your ring detector and ensure it is located at the position of loudest volume. Your phone’s ringer volume may need to be turned up.
LIFTING ARM HEIGHT VARIES Tighten the lifting arm retaining screw.
Make sure your remote unit “ringer” switch is in the “on” position.
Check the positioning of the phone on the base to be sure it has not shifted.
Have someone call you. Your remote unit should ring when your telephone rings.
Readjust the arm in rest position.
You are now ready to receive calls up to 150 feet from your telephone.
