Transcript
Getting Started
TelVue® ProVue™ SDI and Analog
1 2
IP ADDRESS ASSIGNMENT
Connect Video & Audio Outputs
DHCP – Dynamic Host Configuration Protocol Your appliance will acquire an IP address from a DHCP server. This isn’t ideal for an appliance like your TelVue® server because your server may be assigned a new IP address unexpectedly, and it can be hard to determine what its current IP address is.
Connect your video and audio outputs per the connection diagrams on the back page.
Static IP You set an IP address during configuration and the appliance always uses that IP address. This is the preferred method because you always know what the IP address is. You will need an available IP address on your network, outside the DHCP range. Contact your IT department to get one. TelVue® recommends an IP address in the form 192.168.nnn.nnn, 172.nnn.nnn.nnn., or 10.nnn.nnn.nnn.
Configure Networking Press the Down arrow on the server’s LCD display to access the Menu. If there is more than one network cable attached to the system, then the first menu will ask which device you want to configure. See diagram for the port numbering.
Ethernet [0]
Ethernet [1]
The Up and Down arrows can be used to select which device to configure. Once the appropriate device has been found, press Enter to continue with the configuration process.
DHCP Reservation The reservation tells your DHCP server to give your appliance the same IP address. This lets you use the simpler DHCP setup for your appliance, while still letting it use the same IP address. Refer to your DHCP server’s documentation to set up a reservation.
3
Select “yes” by using the Up and Down arrows at the DHCP menu to configure the selected ethernet device automatically.
Select the feed type, then press Enter. The different incoming stream types you can select are: unicast, multicast, or source-specific multicast (SSM). If unicast was selected, use the Up and Down arrows to select the UDP port. Press Enter. Then use Up and Down arrows to select or deselect RTP mode.
Once a valid IP address has been entered, press Enter to accept.
TelVue ProVue™ LCD Screen
Use DHCP? yes
Network Config IP, Subnet, GW
CANCEL ENTER
CANCEL ENTER
Press the Down arrow to access the menu. Use the Right arrow button to navigate to the “Configure Input Network Feed” menu, and press Enter. Use the Up and Down arrow keys to select the source of the input feed (eth0 or eth1).
To specifiy the IP address statically, select “no” at the DHCP menu and press Enter. Then use the Left and Right arrows to select the part of the IP address to modify. Use the Up and Down arrows to adjust its value. An underscore will appear below the part of the IP address that is being modified. Configure the subnet mask and default gateway using the above instructions. Press Enter after each address has been configured. Generally, eth0 should be used for control, and eth1 for video. Note that out of the box, eth0 is set to DHCP, and eth1 is set to static IP 1.1.1.1.
Configure Incoming Stream
If multicast was selected, specify the multicast address using the same procedure you used in Step 2. Once set, select the port and RTP mode as described under the unicast instructions above.
4
If SSM was selected, specify the multicast address, then specify the source IP address in the same manner. Once set, select the port and RTP mode as described above.
Configure Output Format Press the Down arrow to access the menu. 1a.[ProVue Analog start here.] Use the Right arrow button to navigate to the “Set Output Configuration” menu, and press Enter. You will be prompted to choose between Composite, S-Video, Component, or HDMI. Continue to 1b. 1b. [ProVue SDI start here.] Use the Right arrow button to navigate to the “Set Output Format” menu. 2. The next screen will present a list of possible output formats, ranging from SD to HD, and are available in several different resolutions.
Set IP address 192.168.1.127 CANCEL ENTER
3. Scroll through the list using the Up and Down arrow keys until the desired format is found. Press the Enter key to complete the process. 16000 Horizon Way, Suite 500 Mount Laurel, NJ 08054 800.885.8886 www.telvue.com/support
Toll Free: 800-885-8886 Email:
[email protected] Support Portal: http://www.telvue.com/support APIs: http://www.telvue.com/api Training Videos: http://www.telvue.com/training
QSG_TC_7_13_V2
Getting Started
TelVue® ProVue™ SDI and Analog
TelVue ProVue™ Analog Video and Audio Output Connectors
TelVue ProVue™ SDI Video and Audio Output Connectors
Genlock
HDMI 4:2:2 Input HDMI 4:2:2 Output
HD-SDI Out
Deck Control - Not Used
HD-SDI In
Breakout Cable
S-Video Connector
BNC Connector
For S-Video out, connect the: • S-Video green connector to the breakout cable #4 Y Out green connector • S-Video blue connector to the breakout cable #5 B-Y Out blue connector
What’s Next? We have many resources available to help you further and get you up and running faster! Solutions, documentation, literature, training videos and more are all at your fingertips. Check them out! http://www.telvue.com/support/ http://www.telvue.com/support/training/ http://www.telvue.com/manual/provue
4 Breakout Cable
Analog Video Output - Y Out (For Composite)
8
If you would like to set up an appointment for training please contact the TelVue® Support team at
[email protected].
7 10 5
Analog Audio Input Audio In Left
9
14 12
15
13
Analog Video Input Y In
3
Analog Video Input R-Y In
Analog Audio Output Audio Out Left Analog Audio Input Audio In Right Analog Audio Output Analog Video Audio Out Right Output R-Y Out
Digital Audio Output AES/EBU Out Analog Video Output B-Y Out
Analog Video Input B-Y In
16000 Horizon Way, Suite 500 Mount Laurel, NJ 08054 800.885.8886 www.telvue.com/support
Toll Free: 800-885-8886 Email:
[email protected] Support Portal: http://www.telvue.com/support APIs: http://www.telvue.com/api Training Videos: http://www.telvue.com/training QSG_TP_7_13_V2
