Transcript
Tempest2400 Remote Transceiver Technical Data Sheet
ABOUT The Tempest2400 Remote Transceiver (RT) allows the Tempest2400 BaseStation antenna to be located up to 1500 ft. (450 m) from the BaseStation without any loss of RF signal. The RT is connected to the BaseStation via a standard CAT 5/6 cable using RJ-45 connectors. Power is provided over the CAT 5/6 cable so that no local power is required for the RT to operate normally. The RT is constructed of aluminum alloy. It comes with a universal mounting plate that can be used to mount the transceiver to poles, walls, or other desired areas. When ordering, reference Part Number TMP-RT24 (or TMP-RT24-EU for European sales). FEATURES & BENEFITS • For use with the Tempest2400 BaseStation
• Weather-resistant for outdoor use
• Allows remote location of antennas from the base with no RF signal loss
• Rx, Tx, Sync, Config, and Power LED indicators
• Cable runs of up to 1500 ft. (457 m)
• Includes two omni-directional 2 dBi antennas
• Operates on standard CAT 5/6 cable
• Can remote antennas from the Transceiver with low loss coaxial cable
• Power is provided over the cable from BaseStation
• RP-TNC antenna connectors (2)
• RoHS compliant
• Durable aluminum alloy enclosure
OPERATION One Remote Transceiver can be connected to a single Tempest BaseStation (2- or 4-channel) to provide RF coverage where it is needed. A direct connection is required, and once connected, the Base Radio is disabled. (The transceiver will not operate properly if connected to a Local Area Network (LAN) or routed through a network device such as a router or switch.) The transceiver has two RP-TNC antenna connectors on top of the enclosure that can attach the standard 2 dBi omni-directional antennas, or employ optional directional antenna via low loss coaxial cable.
LED INDICATORS The Remote Transceiver is equipped with five LED indicators so that the user can ensure proper operation of the transceiver. • • •
Power LED illuminates whenever the BaseStation is providing adequate power to the transceiver over the CAT 5/6 cable. Sync and Config LEDs indicate that the transceiver has been properly initialized and is communicating with the BaseStation. Receive (Rx) and Transmit (Tx) LEDs indicate proper data transfer to and from the BaseStation and wireless BeltStation.
DURABILITY The Remote Transceiver is weather resistant and is intended for use outdoors. It is recommended, however, that in extreme weather conditions appropriate measures are taken to ensure that no water enters into the enclosure.
+1.334.321.1160
www.plianttechnologies.com
Model TMA-RMTCVR-01
page 2
SYSTEM SPECIFICATIONS* RF Frequency 2400 to 2480 MHz RF Scheme FHSS with TDMA Effective Radiated Power 100mW using 2dBi antenna Receiver Sensitivity -93 dBm for 10-5 BER Radio Certification FCC Part 15.247, ETS 300 328 v1.8.1 rules (apply to model numbers ending in “EU” only**), Canadian RSS-210, license free. Transmission Range 1,000 ft. (304.8 m) under ideal conditions. 500 ft. to 900 ft. (152.4 m to 274.3 m) typical Audio Dynamic Range >94 dB Audio Frequency Response 300Hz–3.8KHz with proprietary audio voice shaping System Latency Less than 50 ms direct RoHS Compliant Yes
TRANSCEIVER SPECIFICATIONS* Maximum Distance, Base to Transceiver 1,500 ft (457.2 m), powered from the BaseStation Connection to BaseStation CAT-5 standard wiring BaseStations Supported per Transceiver 1 Number of Antenna Ports per Transceiver 2 Antenna Connector Type RP-TNC Supplied Antenna Whip antenna (2) Dimensions with Antennas (inches) H 12 in. × W 3.7 in. × D 1.7 in. (30.5 cm × 9.4 cm × 4.3 cm) Weight 11 oz (312 g) Operating Environment -20° to 50° C (-4° to 122° F); 10% to 90% Humidity
*Notice About Specifications While Pliant makes every attempt to maintain the accuracy of the information contained in this datasheet, this information is subject to change without notice. Please check our website for the latest system specifications and certifications. **TMA-RMTCVR-EU models meet the same specifications and comply with ETSI standards (300.328 v1.8.1). Non-EU models are non-compliant with ETSI standards. P l i a n t Te c h n o l o g i e s, L L C Te m p e s t ® 2 0 5 Te c h n o l o g y Pa r k w a y Auburn, AL 36830 USA w w w. p l i a n t t e c h n o l o g i e s. c o m Phone +1.334.321.1160 To l l - Fr e e 1 . 8 4 4 . 4 7 5 . 4 2 6 8 o r 1 . 8 4 4 . 4 P L I A N T Fax +1.334.321.1162
T M 2 4 0 0 RT D a t a S h e e t _ T M P - RT 2 4 & E U _ 3 . 1 6 C o p y r i g h t © 2 0 1 6 P l i a n t Te c h n o l o g i e s, L L C. A l l r i g h t s r e s e r v e d . Th e P l i a n t ™ w o r d m a r k a n d t h e P l i a n t “ P ” l o g o a r e t r a d e m a r k s o f P l i a n t Te c h n o l o g i e s, L L C. Th e Te m p e s t ® a n d S m a r t B o o m ® w o r d m a r k s a r e t r a d e m a r k s o f C o a c h C o m m L L C. A n y a n d all other trademark references within this document are property of their respective o w n e r s.
