Preview only show first 10 pages with watermark. For full document please download

Termin Lov Servery řady Nport 6000 A Cn2600

Rating
Date

September 2018
Size

2.3MB
Views

6,482
Categories

Computers & electronics Computer components Interface components Serial converters/repeaters/isolators

Transcript

Terminal Servers Product Selection Guide NPort® 6000 Terminal Servers�� 9-2 CN2600 Terminal Servers�� 9-4 Secure Terminal Servers Secure Terminal Servers�� 9-6 NPort® 6150 Series: 1-port RS-232/422/485 secure terminal server��9-8 NPort® 6250 Series: 2-port RS-232/422/485 secure terminal servers��9-10 NPort® 6450 Series: 4-port RS-232/422/485 secure terminal server��9-13 NPort® 6600 Series: 8/16/32-port RS-232/422/485 rackmount terminal servers��9-16 CN2600 Series: 8/16-port RS-232/422/485 terminal servers with dual LAN redundancy��9-19 9 Terminal Servers Terminal Servers NPort® 6000 Terminal Servers NPort 6150/6150-T NPort 6250/6250-T NPort 6250-M-SC/ 6250-M-SC-T NPort 6250-S-SC/ 6250-S-SC-T NPort 6450/6450-T NPort 6610-8 NPort 6610-8-48V NPort 6610-16 NPort 6610-16-48V 1 (multi-mode) 1 (single-mode) – – – – – LAN Interface 9 10/100BaseT(X) Ports Magnetic Isolation Protection 100BaseFX Ports 1 port (8-pin RJ45 connector) 1.5 kV – – Expansion Modules Terminal Servers > Product Selection Guide 10/100BaseT(X) (RJ45) Multi-mode Fiber (SC) Single-mode Fiber (SC) Modem – – – – 1 or 2 ports 1 or 2 ports 1 or 2 ports 1 or 2 ports 1 or 2 ports – – – – 1 or 2 ports 1 or 2 ports 1 or 2 ports 1 or 2 ports 1 or 2 ports – – – – 1 or 2 ports 1 or 2 ports 1 or 2 ports 1 or 2 ports 1 or 2 ports – – – – P P P P P Serial Interface RS-232 Ports RS-232/422/485 Ports Connectors Communication Parameters Flow Control Baudrate 15 kV ESD Protection RS-485 Data Direction Control RS-232 Console Port – – – – – 8 8 16 16 1 2 2 2 4 – – – – DB9 male DB9 male DB9 male DB9 male DB9 male 8-pin RJ45 8-pin RJ45 8-pin RJ45 8-pin RJ45 Data Bits: 5, 6, 7, 8; Stop Bits: 1, 1.5, 2; Parity: None, Even, Odd, Space, Mark RTS/CTS, DTR/DSR, XON/XOFF 50 bps to 921.6 kbps (supports non-standard baudrates) P P P P P P P P P ADDC ADDC ADDC ADDC ADDC ADDC ADDC ADDC ADDC P P P P P P P P P 64 KB 64 KB – 64 KB 64 KB P 64 KB 64 KB P 64 KB 64 KB P 64 KB 64 KB P 64 KB 64 KB P 64 KB 64 KB P 64 KB 64 KB P 64 KB 64 KB P Advanced Features Serial Data Log Offline Port Buffering SD Slot Software Network Protocols Security Protocols Configuration Options Windows Real COM Drivers Fixed TTY Drivers Linux Real TTY Drivers Management IP Routing Standard Operation Modes Secure Operation Modes Terminal Sessions ICMP, IPv4/v6, TCP, UDP, DHCP, BOOTP, Telnet, DNS, SNMP V1/V2c/V3, DDNS, HTTP, SMTP, HTTPS, SSL, SSH, PPPoE, RFC2217, IPv6, IPv4, Turbo Ring, Turbo Ring 2 DES, 3DES, AES, SSH, SSL Web Console, Telnet Console, Serial Console, Windows Search Utility Windows 95/98/ME/NT/2000, Windows XP/2003/Vista/2008/7/8/8.1 (x86/x64), Windows 2008 R2/2012/2012 R2 (x64), Windows Embedded CE 5.0/6.0, Windows XP Embedded SCO Unix, SCO OpenServer, UnixWare 7, QNX 4.25, QNX 6, Solaris 10, FreeBSD, AIX 5.x, HP-UX 11i, Mac OS X Linux 2.4.x, 2.6.x, 3.x SNMP MIB-II Static, RIP-I, RIP-II Real COM, TCP Server, TCP Client, UDP, Pair Connection, RFC2217, Terminal, Reverse Telnet, Ethernet Modem, Printer, PPP, Disabled Secure Real COM, Secure TCP Server, Secure TCP Client, Secure Pair Connection, SSH, Reverse SSH 8 sessions per port Physical Characteristics Housing Weight Dimensions (mm) Metal 700 g 67 x 100.4 x 29 730 g 77 x 111 x 29 730 g 77 x 111 x 29 730 g 77 x 111 x 29 1020 g 158 x 103 x 35 3460 g 440 x 195 x 44 3460 g 440 x 195 x 44 3580 g 440 x 195 x 44 3580 g 440 x 195 x 44 100 to 240 VAC 285 mA @ 100 V 190 mA @ 240 V ±48 VDC 100 to 240 VAC 285 mA @ 100 V 190 mA @ 240 V ±48 VDC Environmental Limits Operating Temperature Storage Temperature Ambient Relative Humidity Altitude 0 to 55°C (-40 to 75°C for T models) -40 to 75°C 5 to 95% (non-condensing) Up to 2000 m Note: Please contact Moxa if you require products guaranteed to function properly at higher altitudes. Power Requirements Input Voltage 12 to 48 VDC 12 to 48 VDC 12 to 48 VDC 12 to 48 VDC 12 to 48 VDC Power Consumption 285 mA @ 12 V 150 mA @ 24 V 333 mA @ 12 V 173 mA @ 24 V 428 mA @ 12 V 219 mA @ 24 V 376 mA @ 12 V 193 mA @ 24 V 730 mA @ 12 V 330 mA @ 24 V 293 mA @ 48 V 293 mA @ 48 V Standards and Certifications Safety EMC UL 60950-1, EN 60950-1 CE (EN 55022 Class A, EN 55024), FCC Part 15 Subpart B Class A Reliability Buzzer, RTC, WDT MTBF Warranty 9-2 P P P 231,709 hrs 226,128 hrs 225,762 hrs 5 years (see www.moxa.com/warranty) w w w. m o x a . c o m P 225,762 hrs P 120,354 hrs [email protected] P 135,891 hrs P 135,891 hrs P 102,373 hrs P 102,373 hrs Serial Connectivity NPort® 6000 Terminal Servers NPort 6610-32 NPort 6610-32-48V NPort 6650-8/ 6650-8-T NPort 6650-8-48V NPort 6650-16/ 6650-16-T NPort 6650-16-48V NPort 6650-32 NPort 6650-32-48V 1 or 2 ports 1 or 2 ports 1 or 2 ports P 1 or 2 ports 1 or 2 ports 1 or 2 ports P 1 or 2 ports 1 or 2 ports 1 or 2 ports P 1 or 2 ports 1 or 2 ports 1 or 2 ports P 1 or 2 ports 1 or 2 ports 1 or 2 ports P 1 or 2 ports 1 or 2 ports 1 or 2 ports P – 16 – 16 – 32 – 32 LAN Interface 10/100BaseT(X) Ports Magnetic Isolation Protection 100BaseFX Ports 1 port (8-pin RJ45 connector) 1.5 kV – Expansion Modules 10/100BaseT(X) (RJ45) Multi-mode Fiber (SC) Single-mode Fiber (SC) Modem 1 or 2 ports 1 or 2 ports 1 or 2 ports P 1 or 2 ports 1 or 2 ports 1 or 2 ports P 9 Serial Interface 32 32 – – – – 8 8 8-pin RJ45 Data Bits: 5, 6, 7, 8; Stop Bits: 1, 1.5, 2; Parity: None, Even, Odd, Space, Mark RTS/CTS, DTR/DSR, XON/XOFF 50 bps to 921.6 kbps (supports non-standard baudrates) P P P P P P P P ADDC ADDC ADDC ADDC ADDC ADDC ADDC ADDC P P P P P P P P 64 KB 64 KB P 64 KB 64 KB P 64 KB 64 KB P 64 KB 64 KB P 64 KB 64 KB P 64 KB 64 KB P 64 KB 64 KB P 64 KB 64 KB P Terminal Servers > Product Selection Guide RS-232 Ports RS-232/422/485 Ports Connectors Communication Parameters Flow Control Baudrate 15 kV ESD Protection RS-485 Data Direction Control RS-232 Console Port Advanced Features Serial Data Log Offline Port Buffering SD Slot Software Network Protocols Security Protocols Configuration Options Windows Real COM Drivers Fixed TTY Drivers Linux Real TTY Drivers Management IP Routing Standard Operation Modes Secure Operation Modes Terminal Sessions ICMP, IPv4/v6, TCP, UDP, DHCP, BOOTP, Telnet, DNS, SNMP V1/V2c/V3, DDNS, HTTP, SMTP, HTTPS, SSL, SSH, PPPoE, RFC2217, IPv6, IPv4, Turbo Ring, Turbo Ring 2 DES, 3DES, AES, SSH, SSL Web Console, Telnet Console, Serial Console, Windows Search Utility Windows 95/98/ME/NT/2000, Windows XP/2003/Vista/2008/7/8/8.1 (x86/x64), Windows 2008 R2/2012/2012 R2 (x64), Windows Embedded CE 5.0/6.0, Windows XP Embedded SCO Unix, SCO OpenServer, UnixWare 7, QNX 4.25, QNX 6, Solaris 10, FreeBSD, AIX 5.x, HP-UX 11i, Mac OS X Linux 2.4.x, 2.6.x, 3.x SNMP MIB-II Static, RIP-I, RIP-II Real COM, TCP Server, TCP Client, UDP, Pair Connection, RFC2217, Terminal, Reverse Telnet, Ethernet Modem, Printer, PPP, Disabled Secure Real COM, Secure TCP Server, Secure TCP Client, Secure Pair Connection, SSH, Reverse SSH 8 sessions per port Physical Characteristics Housing Weight Dimensions (mm) Metal 3600 g 440 x 195 x 44 3600 g 440 x 195 x 44 3460 g 440 x 195 x 44 3460 g 440 x 195 x 44 3580 g 440 x 195 x 44 3580 g 440 x 195 x 44 3600 g 440 x 195 x 44 3600 g 440 x 195 x 44 – -40 to 75°C – -40 to 75°C – – – ±48 VDC Environmental Limits Standard Temperature Wide Temperature Storage Temperature Ambient Relative Humidity Operating Temperature Altitude 0 to 55°C – -40 to 75°C 5 to 95% (non-condensing) Up to 2000 m Note: Please contact Moxa if you require products guaranteed to function properly at higher altitudes. Power Requirements Input Voltage Power Consumption 100 to 240 VAC 285 mA @ 100 V 190 mA @ 240 V ±48 VDC 293 mA @ 48 V 100 to 240 VAC 285 mA @ 100 V 190 mA @ 240 V ±48 VDC 293 mA @ 48 V 100 to 240 VAC 285 mA @ 100 V 190 mA @ 240 V 293 mA @ 48 V 100 to 240 VAC 285 mA @ 100 V 190 mA @ 240 V 293 mA @ 48 V ±48 VDC P 101,783 hrs P 101,783 hrs P 68,177 hrs P 68,177 hrs Standards and Certifications Safety EMC UL 60950-1, EN 60950-1 CE (EN 55022 Class A, EN 55024), FCC Part 15 Subpart B Class A Reliability Buzzer, RTC, WDT MTBF Warranty P P 68,707 hrs 68,707 hrs 5 years (see www.moxa.com/warranty) P 135,370 hrs P 135,370 hrs [email protected] w w w. m o x a . c o m 9-3 Terminal Servers CN2600 Terminal Servers CN2610-8-2AC CN2610-16-2AC CN2650-8 CN2650-16 8 16 – – 8-pin RJ45 Data Bits: 5, 6, 7, 8; Stop Bits: 1, 1.5, 2; Parity: None, Even, Odd, Space, Mark RTS/CTS, DTR/DSR, XON/XOFF 50 bps to 921.6 kbps P P – – – 8 – 16 P – P – ADDC® ADDC® ADDC® ADDC® P P P P LAN Interface 10/100BaseT(X) Ports Magnetic Isolation Protection 9 2 ports (2 IPs, 8-pin RJ45 connectors) 1.5 kV Serial Interface Terminal Servers > Product Selection Guide RS-232 Ports RS-232/422/485 Ports Connectors Communication Parameters Flow Control Baudrate 15 kV ESD Protection 2 kV isolation protection RS-485 Data Direction Control RS-232 Console Port Advanced Features Serial Data Log Offline Port Buffering 128K 128K Software Network Protocols Security Protocols Configuration Options Windows Real COM Drivers Fixed TTY Drivers Linux Real TTY Drivers Management IP Routing Standard Operation Modes Terminal Sessions ICMP, IPv4, TCP, UDP, DHCP, BOOTP, Telnet, DNS, SNMP V1/V2c/V3, HTTP, SMTP, ARP, PPPoE, DDNS RADIUS, HTTPS, SSH, PAP, CHAP Web Console, Telnet Console, Serial Console, Windows Search Utility Windows 95/98/ME/NT/2000, Windows XP/2003/Vista/2008/7/8/8.1 (x86/x64), Windows 2008 R2/2012/2012 R2 (x64), Windows Embedded CE 5.0/6.0, Windows XP Embedded SCO Unix, SCO OpenServer, UnixWare 7, QNX 4.25, QNX 6, Solaris 10, FreeBSD, AIX 5.x, HP-UX 11i, Mac OS X Linux 2.4.x, 2.6.x, 3.x SNMP MIB-II Static, RIP-I, RIP-II Real COM, TCP Server, TCP Client, UDP, RFC2217, Terminal, Reverse Telnet, PPP, DRDAS, Redundant COM, Disabled 8 sessions per port Physical Characteristics Housing Weight Dimensions (mm) Metal 3760 g 440 x 198 x 45.5 3980 g 3740 g 3790 g Environmental Limits Operating Temperature Storage Temperature Ambient Relative Humidity Altitude 0 to 55°C -40 to 75°C 5 to 95% (non-condensing) Up to 2000 m Note: Please contact Moxa if you require products guaranteed to function properly at higher altitudes. Power Requirements Dual Power Inputs for Redundancy Input Voltage Power Consumption P P – – P P 100 to 240 VAC, 47 to 63 Hz 235 mA @ 100 VAC, 145 mA @ 240 V Standards and Certifications Safety EMC UL 60950-1, EN 60950-1 CE (EN 55022 Class A, EN 55024), FCC Part 15 Subpart B Class A Reliability Buzzer, RTC, WDT MTBF Warranty 9-4 P 99,302 hrs 5 years (see www.moxa.com/warranty) P w w w. m o x a . c o m [email protected] Serial Connectivity CN2600 Terminal Servers CN2650-8-2AC CN2650-8-2AC-T CN2650-16-2AC CN2650-16-2AC-T CN2650I-8 CN2650I-16 CN2650I-8-2AC CN2650I-16-2AC 16 DB9 male 8 DB9 male 16 DB9 male P P ADDC® P P P ADDC® P P P ADDC® P LAN Interface 10/100BaseT(X) Ports Magnetic Isolation Protection 2 ports (2 IPs, 8-pin RJ45 connectors) 1.5 kV Serial Interface – 8 16 8 8-pin RJ45 8-pin RJ45 DB9 male Data Bits: 5, 6, 7, 8; Stop Bits: 1, 1.5, 2; Parity: None, Even, Odd, Space, Mark RTS/CTS, DTR/DSR, XON/XOFF 50 bps to 921.6 kbps P P P P – – ADDC® ADDC® ADDC® P P P 9 Terminal Servers > Product Selection Guide RS-232 Ports RS-232/422/485 Ports Connectors Communication Parameters Flow Control Baudrate 15 kV ESD Protection 2 kV isolation protection RS-485 Data Direction Control RS-232 Console Port Advanced Features Serial Data Log Offline Port Buffering 128 KB 128 KB Software Network Protocols Security Protocols Configuration Options Windows Real COM Drivers Fixed TTY Drivers Linux Real TTY Drivers Management IP Routing Standard Operation Modes Terminal Sessions ICMP, IPv4, TCP, UDP, DHCP, BOOTP, Telnet, DNS, SNMP V1/V2c/V3, HTTP, SMTP, ARP, PPPoE, DDNS RADIUS, HTTPS, SSH, PAP, CHAP Web Console, Telnet Console, Serial Console, Windows Search Utility Windows 95/98/ME/NT/2000, Windows XP/2003/Vista/2008/7/8/8.1 (x86/x64), Windows 2008 R2/2012/2012 R2 (x64), Windows Embedded CE 5.0/6.0, Windows XP Embedded SCO Unix, SCO OpenServer, UnixWare 7, QNX 4.25, QNX 6, Solaris 10, FreeBSD, AIX 5.x, HP-UX 11i, Mac OS X Linux 2.4.x, 2.6.x, 3.x SNMP MIB-II Static, RIP-I, RIP-II Real COM, TCP Server, TCP Client, UDP, RFC2217, Terminal, Reverse Telnet, PPP, DRDAS, Redundant COM, Disabled 8 sessions per port Physical Characteristics Housing Weight Dimensions (mm) Metal 3900 g 440 x 198 x 45.5 3980 g 3666 g 3776 g 3932 g 4022 g -40 to 75°C – – – – – P P P P P Environmental Limits Standard Temperature Wide Temperature Storage Temperature Ambient Relative Humidity Operating Temperature Altitude 0 to 55°C -40 to 75°C -20 to 70°C 5 to 95% (non-condensing) Up to 2000 m Note: Please contact Moxa if you require products guaranteed to function properly at higher altitudes. Power Requirements Dual Power Inputs for Redundancy Input Voltage Power Consumption P P – 100 to 240 VAC, 47 to 63 Hz 235 mA @ 100 VAC, 145 mA @ 240 VAC Standards and Certifications Safety EMC UL 60950-1, EN 60950-1 CE (EN 55022 Class A, EN 55024), FCC Part 15 Subpart B Class A Reliability Buzzer, RTC, WDT MTBF Warranty P P 99,302 hrs 5 years (see www.moxa.com/warranty) P [email protected] w w w. m o x a . c o m 9-5 Terminal Servers Secure Terminal Servers 9 NPort® 6000 secure terminal servers provide serial-to-Ethernet connectivity that is both reliable and secure. They can be used to connect any serial device to an Ethernet network using a variety of operation modes—Real COM, TCP Server, TCP Client, UDP, RFC2217, Pair Connection, Ethernet Modem, Terminal, Reverse Terminal, Printer, and Dial in/out. For applications that require data security, such as banking, telecom, access control, and remote site management, secure modes are also available—Secure TCP Server, Secure TCP Client, Secure Pair-Connection, Secure Real COM, and Secure Terminal modes. Safe Data Communication Terminal Servers > Secure Terminal Servers Secure Data Communication with SSL Network security is a critical issue for certain applications, and is especially important when data is transmitted over the Internet where it is vulnerable to interception by third parties. The NPort® 6000 secure terminal servers use SSL to implement secure data transmission for Secure TCP Server, Secure TCP Client, Secure Pair Connection, and Secure Real COM modes. The NPort®’s drivers follow the SSL standard and automatically negotiate the encryption key. To prevent hacker attacks, the NPort® will automatically switch from DES/3DES to AES encryption. Reliable Data Communication Port Buffering that Preserves Data if the Ethernet Connection Fails For mission-critical applications, data collected from a serial Connection device must be safeguarded in case the Ethernet network gets disconnected. The NPort® 6000 provides exceptionally reliable data transmission by saving serial data to an internal 64 KB port 9-6 w w w. m o x a . c o m buffer if the Ethernet connection fails. When the Ethernet network is reconnected, data in the buffer is automatically released and sent to the appropriate destination. For the NPort® 6250, 6450, and 6650, this buffer can be expanded by installing an SD card. [email protected] Serial Connectivity Ethernet Port Expansion (NPort® 6450/6600 only) Although more and more devices are now Ethernet-ready, many legacy devices only provide a serial interface. The main purpose of a device server is to connect serial devices to an Ethernet network, allowing engineers to integrate all of their devices into an Ethernet environment. A problem can arise if both Ethernet-ready and legacy serial devices need to be connected at the same location. The NPort® 6000 can use the Ethernet expansion module to add additional Ethernet ports, effectively allowing operation as a combination Ethernet switch and device server. By using the NPort® 6000’s Ethernet expansion modules, users no longer need to invest in a more expensive switch or hub to connect every device. Modules are available for different Ethernet media, including copper Ethernet, multimode fiber, and single-mode fiber. Ethernet expansion modules can also be used to create a cascading topology in which device servers are connected to each other in a daisy chain arrangement. The NM-Modem network module can be used to provide NPort® 6000 secure terminal servers with an automatic backup capability. The NPort® 6000 backup function makes data transmission safer and more reliable. Interchangeable modules for Ethernet expansion 2 fiber Ethernet ports (single or multi mode) 1 RJ45 Ethernet port 2 RJ45 Ethernet ports NM-Modem Terminal Servers > Secure Terminal Servers 1 fiber Ethernet port (single or multi mode) 9 Ethernet Ring Topology with Fast Recovery (NPort® 6450/6600 only) NPort® 6000 secure terminal servers support the Turbo Ring protocol for cascade topologies. With Turbo RingTM, if any segment of the daisy-chain ring is disconnected, the network will recover in less than 300 ms. Ethernet Serial Fiber Redundant Ethernet (NPort® 6450/6600 only) The NM-Modem network module can be used to provide NPort® 6000 secure terminal servers with an automatic backup capability. When the backup function is enabled, the NPort® 6000 will check the remote host connection on the Ethernet side after powering on. Once a connection failure has occurred, data from the serial device will be sent Ethernet Serial out through the PSTN network. When the remote host on the Ethernet side returns to normal status, data will again be sent through the Ethernet connection. The NPort® 6000 backup function makes data transmission safer and more reliable. Remote Host Internet Ethernet [email protected] w w w. m o x a . c o m 9-7 Terminal Servers NPort® 6150 Series 1-port RS-232/422/485 secure terminal servers ››Secure operation modes for Real COM, TCP Server, TCP Client, Pair Connection, Terminal, and Reverse Terminal ››Non-standard baudrates supported with high precision ››Automatic RS-485 data direction control with Moxa’s patented ADDC® ››Enhanced remote configuration with HTTPS and SSH ››Port buffers for storing serial data when the Ethernet is off-line ››Supports IPv6 ››Generic serial commands supported in Command-by-Command 9 mode Terminal Servers > NPort® 6150 Series Overview The NPort® 6150 1-port device servers use the SSL and SSH protocols to transmit encrypted serial data over Ethernet. The NPort® Secure Data Transmission For many applications, guaranteeing secure data transmission is an important concern when connecting serial devices to a network. To answer this concern, the NPort® 6150 supports the SSL and SSH protocols, which work by encrypting data before sending it over the network. With the NPort® 6150, users can rest assured that serial data is transmitted securely over both private and public networks. Specifications Ethernet Interface Number of Ports: 1 Speed: 10/100 Mbps, auto MDI/MDIX Connector: 8-pin RJ45 Magnetic Isolation: 1.5 kV built-in Serial Interface Number of Ports: 1 Serial Standards: RS-232/422/485 Connector: DB9 male RS-485 Data Direction Control: ADDC® (Automatic Data Direction Control) Serial Line Protection: 15 kV ESD protection for all signals Console Port: Serial port doubles as RS-232 console port Serial Communication Parameters Data Bits: 5, 6, 7, 8 Stop Bits: 1, 1.5, 2 Parity: None, Even, Odd, Space, Mark Flow Control: RTS/CTS, DTR/DSR, XON/XOFF Baudrate: 50 bps to 921.6 kbps (supports non-standard baudrates) Pull High/Low Resistor for RS-485: 1 kΩ, 150 kΩ Serial Signals Software Operation Modes Standard: Real COM, TCP Server, TCP Client, UDP, Pair Connection, RFC2217, Terminal, Reverse Telnet, Ethernet Modem, Printer, PPP, Disabled Secure: Secure Real COM, Secure TCP Server, Secure TCP Client, Secure Pair Connection, SSH, Reverse SSH Applications Terminal Sessions: 8 sessions per port Physical Characteristics Environmental Limits Network Protocols: ICMP, IPv4/v6, TCP, UDP, DHCP, BOOTP, Telnet, DNS, SNMP V1/V2c/V3, HTTP, SMTP, ARP, PPPoE w w w. m o x a . c o m Security Protocols: DES, 3DES, AES, SSH, SSL Configuration Options: Web Console, Serial Console, Telnet Console, Windows Search Utility Windows Real COM Drivers: Windows 95/98/ME/NT/2000, Windows XP/2003/Vista/2008/7/8/8.1 (x86/x64), Windows 2008 R2/2012/2012 R2 (x64), Windows Embedded CE 5.0/6.0, Windows XP Embedded Fixed TTY Drivers: SCO Unix, SCO OpenServer, UnixWare 7, QNX 4.25, QNX 6, Solaris 10, FreeBSD, AIX 5.x, HP-UX 11i, Mac OS X Linux Real TTY Drivers: Linux 2.4.x, 2.6.x, 3.x Management: SNMP MIB-II IP Routing: Static, RIP-I, RIP-II Housing: Metal Weight: 700 g Dimensions: Without ears: 67 x 100.4 x 29 mm (2.64 x 3.95 x 1.1 in) With ears: 90 x 100.4 x 29 mm (3.54 x 3.95 x 1.1 in) RS-232: TxD, RxD, RTS, CTS, DTR, DSR, DCD, GND RS-422: Tx+, Tx-, Rx+, Rx-, GND RS-485-4w: Tx+, Tx-, Rx+, Rx-, GND RS-485-2w: Data+, Data-, GND 9-8 6150’s 3-in-1 serial port supports RS-232, RS-422, and RS-485, with the interface selected from an easy-to-access configuration menu. Operating Temperature: Standard Models: 0 to 55°C (32 to 131°F) Wide Temp. Models: -40 to 75°C (-40 to 167°F) [email protected] Serial Connectivity Storage Temperature: -40 to 75°C (-40 to 167°F) Ambient Relative Humidity: 5 to 95% (non-condensing) Altitude: Up to 2000 m EMS: EN 55024, EN 61000-4-2 (ESD) Level 2/3, EN 61000-4-3 (RS) Level 2, EN 61000-4-4 (EFT) Level 2, EN 61000-4-5 (Surge) Level 2, EN 61000-4-6 (CS) Level 2, EN 61000-4-8 Level 1, EN 61000-4-11 Freefall: IEC-68-2-6, IEC-68-2-34, IEC-68-2-32 Vibration: IEC-68-2-6, IEC-68-2-34 Green Product: RoHS, CRoHS, WEEE Note: Please contact Moxa if you require products guaranteed to function properly at higher altitudes. Power Requirements Input Voltage: 12 to 48 VDC Power Consumption: 285 mA @ 12 V, 150 mA @ 24 V Alarm Contact: Relay output with current carrying capacity of 1 A @ 24 VDC Power Line Protection: 1 kV burst (EN 61000-4-4: EFT/B), 0.5 kV surge (EN 61000-4-5) Standards and Certifications Reliability Safety: UL 60950-1, EN 60950-1 EMI: EN 55022 Class A, FCC Part 15 Subpart B Class A Alert Tools: Built-in buzzer and RTC (real-time clock) Automatic Reboot Trigger: Built-in WDT (watchdog timer) MTBF (mean time between failures): 231,709 hrs Warranty Warranty Period: 5 years Details: See www.moxa.com/warranty Dimensions and Pin Assignment 9 Terminal Servers > NPort® 6150 Series Unit: mm (inch) DK-35A DIN-Rail Kit 29 (1.14) 28 (1.10) Available Accessory 24.9 (0.98) 12.45 (0.49) 100.4 (3.95) O 3.2 (0.13) DB9 male connector 1 2 3 4 5 Pin Assignment O7 (0.28) 6 7 8 9 27 (1.06) PIN 1 2 3 4 5 6 7 8 67 (2.64) 79 (3.11) 90 (3.54) RS-232 DCD RxD TxD DTR GND DSR RTS CTS RS-422/485-4w TxD-(A) TxD+(B) RxD+(B) RxD-(A) GND – – – RS-485-2w – – Data+(B) Data-(A) GND – – – Ordering Information Available Models NPort 6150: 1-port RS-232/422/485 secure device server NPort 6150-T: 1-port RS-232/422/485 secure device server, -40 to 75°C operating temperature Optional Accessories (can be purchased separately) Package Checklist • 1 NPort 6150 device server • 100 to 240 VAC power adapter (excluding T models) • Documentation and software CD • Quick installation guide (printed) • Warranty card DK-35A: Mounting kit for 35-mm DIN-Rail PWR-12150-USJP-SA-T: 100 to 240 VAC input, 12 VDC / 1.5 A output, screw-type, US/JP plug, -40 to 75°C operating temperature PWR-12150-EU-SA-T: 100 to 240 VAC input, 12 VDC / 1.5 A output, screw-type, EU plug, -40 to 75°C operating temperature PWR-12150-UK-SA-T: 100 to 240 VAC input, 12 VDC / 1.5 A output, screw-type, UK plug, -40 to 75°C operating temperature PWR-12150-CN-SA-T: 100 to 240 VAC input, 12 VDC / 1.5 A output, screw-type, CN plug, -40 to 75°C operating temperature PWR-12150-AU-SA-T: 100 to 240 VAC input, 12 VDC / 1.5 A output, screw-type, AU plug, -40 to 75°C operating temperature [email protected] w w w. m o x a . c o m 9-9 Terminal Servers NPort® 6250 Series 2-port RS-232/422/485 secure terminal servers ››Secure operation modes for Real COM, TCP Server, TCP Client, Pair Connection, Terminal, and Reverse Terminal ››Non-standard baudrates supported with high precision ››Choice of network medium: 10/100BaseT(X) or 100BaseFX ››Enhanced remote configuration with HTTPS and SSH ››Port buffers for storing serial data when the Ethernet is off-line ››Supports IPv6 ››Generic serial commands supported in Command-by-Command 9 mode Terminal Servers > NPort® 6250 Series Overview The 2-port NPort® 6250 device servers use the SSL and SSH protocols to transmit encrypted serial data over Ethernet. Models are available for connecting to a 10/100BaseT(X) copper Ethernet or 100BaseT(X) fiber network. Both single-mode and multi-mode fiber are supported. Zero Data Loss if Ethernet Connection Fails The NPort® 6250 device servers help guarantee reliability by providing users with secure serial-to-Ethernet data transmission and a customeroriented hardware design. If the Ethernet connection fails, the NPort® 6250 will queue all serial data in its internal 64 KB port buffer. When the Ethernet connection is re-established, the NPort® 6250 will immediately release all of the data in the buffer in the order that it was received. Users can increase the port buffer size by installing an SD card. Specifications Ethernet Interface RS-485 Data Direction Control: ADDC® (Automatic Data Direction Control) Serial Line Protection: 15 kV ESD protection for all signals Console Port: Serial port 1 doubles as RS-232 console port Number of Ports: 1 Speed: 10/100 Mbps, auto MDI/MDIX Connector: 8-pin RJ45 Magnetic Isolation: 1.5 kV built-in Optical Fiber Interface (NPort 6250-S-SC/6250-M-SC) 100BaseFX Multi-mode Single-mode Wavelength 1300 nm 1310 nm Max. TX -14 dBm 0 dBm Min. TX -20 dBm -5 dBm RX Sensitivity -32 dBm -34 dBm Link Budget 12 dB 29 dB Typical Distance 5 kma 4 kmb 40 kmc Saturation -6 dBm -3 dBm a. 50/125 μm, 800 MHz*km fiber optic cable b. 62.5/125 μm, 500 MHz*km fiber optic cable c. 9/125 μm, 3.5 PS/(nm*km) fiber optic cable Serial Interface Number of Ports: 2 Serial Standards: RS-232/422/485 Connector: DB9 male 9-10 w w w. m o x a . c o m Serial Communication Parameters Data Bits: 5, 6, 7, 8 Stop Bits: 1, 1.5, 2 Parity: None, Even, Odd, Space, Mark Flow Control: RTS/CTS, DTR/DSR, XON/XOFF Baudrate: 50 bps to 921.6 kbps (supports non-standard baudrates) Pull High/Low Resistor for RS-485: 1 kΩ, 150 kΩ Serial Signals RS-232: TxD, RxD, RTS, CTS, DTR, DSR, DCD, GND RS-422: Tx+, Tx-, Rx+, Rx-, GND RS-485-4w: Tx+, Tx-, Rx+, Rx-, GND RS-485-2w: Data+, Data-, GND Memory Expansion Slot Slot Type: SD socket (supports up to 2 GB) Software Network Protocols: ICMP, IPv4/v6, TCP, UDP, DHCP, BOOTP, Telnet, DNS, SNMP V1/V2c/V3, HTTP, SMTP, ARP, PPPoE Security Protocols: DES, 3DES, AES, SSH, SSL Configuration Options: Web Console, Serial Console, Telnet Console, Windows Search Utility Windows Real COM Drivers: Windows 95/98/ME/NT/2000, Windows XP/2003/Vista/2008/7/8/8.1 (x86/x64), Windows 2008 R2/2012/2012 R2 (x64), Windows Embedded CE 5.0/6.0, Windows XP Embedded [email protected] Serial Connectivity Fixed TTY Drivers: SCO Unix, SCO OpenServer, UnixWare 7, QNX 4.25, QNX 6, Solaris 10, FreeBSD, AIX 5.x, HP-UX 11i, Mac OS X Linux Real TTY Drivers: Linux 2.4.x, 2.6.x, 3.x Management: SNMP MIB-II IP Routing: Static, RIP-I, RIP-II Operation Modes Standard: Real COM, TCP Server, TCP Client, UDP, Pair Connection, RFC2217, Terminal, Reverse Telnet, Ethernet Modem, Printer, PPP, Disabled Secure: Secure Real COM, Secure TCP Server, Secure TCP Client, Secure Pair Connection, SSH, Reverse SSH Applications Terminal Sessions: 8 sessions per port Physical Characteristics Housing: Metal Weight: 730 g Dimensions: Without ears: 77 x 111 x 29 mm (3.30 x 4.37 x 1.1 in) With ears: 89 x 111 x 29 mm (3.50 x 4.37 x 1.1 in) Environmental Limits Safety: UL 60950-1, EN 60950-1 EMI: EN 55022 Class A, FCC Part 15 Subpart B Class A EMS: EN 55024, EN 61000-4-2 (ESD) Level 2/3, EN 61000-4-3 (RS) Level 2, EN 61000-4-4 (EFT) Level 2, EN 61000-4-5 (Surge) Level 2, EN 61000-4-6 (CS) Level 2, EN 61000-4-8 Level 1, EN 61000-4-11 Freefall: IEC-68-2-6, IEC-68-2-34, IEC-68-2-32 Vibration: IEC-68-2-6, IEC-68-2-34 Green Product: RoHS, CRoHS, WEEE Reliability Alert Tools: Built-in buzzer and RTC (real-time clock) Automatic Reboot Trigger: Built-in WDT (watchdog timer) MTBF (mean time between failures): NPort 6250: 226,128 hrs NPort 6250-M-SC: 225,762 hrs NPort 6250-S-SC: 225,762 hrs Warranty Warranty Period: 5 years Details: See www.moxa.com/warranty Note: Please contact Moxa if you require products guaranteed to function properly at higher altitudes. Pin Assignment Power Requirements Input Voltage: 12 to 48 VDC Power Consumption: NPort 6250: 333 mA @ 12 V, 173 mA @ 24 V NPort 6250-M-SC: 428 mA @ 12 V, 219 mA @ 24 V NPort 6250-S-SC: 376 mA @ 12 V, 193 mA @ 24 V Power Line Protection: 1 kV burst (EN 61000-4-4: EFT/B), 0.5 kV surge (EN 61000-4-5) PIN RS-232 RS-422/485-4w RS-485-2w 1 DCD TxD-(A) – 2 RxD TxD+(B) – 3 TxD RxD+(B) Data+(B) 4 DTR RxD-(A) Data-(A) 5 GND GND GND 6 DSR – – 7 RTS – – 8 CTS – – 9 Terminal Servers > NPort® 6250 Series Operating Temperature: Standard Models: 0 to 55°C (32 to 131°F) Wide Temp. Models: -40 to 75°C (-40 to 167°F) Storage Temperature: -40 to 75°C (-40 to 167°F) Ambient Relative Humidity: 5 to 95% (non-condensing) Altitude: Up to 2000 m Standards and Certifications 1 2 3 4 5 DB9 male connector 6 7 8 9 Dimensions Unit: mm (inch) NPort® 6250-M-SC/6250-S-SC 29 (1.14) 28 (1.10) 24.9 (0.98) 111 (4.37) DK-35A DIN-Rail Kit 12.45 (0.49) Ø3.2 (0.13) NPort® 6250 Available Accessory 77 (3.30) 89 (3.50) [email protected] 27 (1.06) Ø7 (0.28) 77 (3.03) 100 (3.94) w w w. m o x a . c o m 9-11 Terminal Servers Ordering Information Available Models NPort 6250: 2-port secure device server, RS-232/422/485 to Ethernet NPort 6250-M-SC: 2-port secure device server, RS-232/422/485 to multi-mode fiber (SC connector) NPort 6250-S-SC: 2-port secure device server, RS-232/422/485 to single-mode fiber (SC connector) NPort 6250-T: 2-port secure device server, RS-232/422/485 to Ethernet, -40 to 75°C operating temperature NPort 6250-M-SC-T: 2-port secure device server, RS-232/422/485 to multi-mode fiber (SC connector), -40 to 75°C operating temperature NPort 6250-S-SC-T: 2-port secure device server, RS-232/422/485 to single-mode fiber (SC connector), -40 to 75°C operating temperature Optional Accessories (can be purchased separately) 9 • 1 NPort 6250 device server • 100 to 240 VAC power adapter (excluding T models) • Documentation and software CD • Quick installation guide (printed) • Warranty card DK-35A: Mounting kit for 35-mm DIN-Rail PWR-12150-USJP-SA-T: 100 to 240 VAC input, 12 VDC / 1.5 A output, screw-type, US/JP plug, -40 to 75°C operating temperature PWR-12150-EU-SA-T: 100 to 240 VAC input, 12 VDC / 1.5 A output, screw-type, EU plug, -40 to 75°C operating temperature PWR-12150-UK-SA-T: 100 to 240 VAC input, 12 VDC / 1.5 A output, screw-type, UK plug, -40 to 75°C operating temperature PWR-12150-CN-SA-T: 100 to 240 VAC input, 12 VDC / 1.5 A output, screw-type, CN plug, -40 to 75°C operating temperature PWR-12150-AU-SA-T: 100 to 240 VAC input, 12 VDC / 1.5 A output, screw-type, AU plug, -40 to 75°C operating temperature Terminal Servers > NPort® 6250 Series 9-12 Package Checklist w w w. m o x a . c o m [email protected] Serial Connectivity NPort® 6450 Series 4-port RS-232/422/485 secure terminal servers ››LCD panel for easy IP address configuration (standard temp. models) ››Secure operation modes for Real COM, TCP Server, TCP Client, Pair Connection, Terminal, and Reverse Terminal ››Non-standard baudrates supported with high precision ››Port buffers for storing serial data when the Ethernet is off-line ››Supports IPv6 ››Ethernet redundancy (STP/RSTP/Turbo Ring) with network module ››Generic serial commands supported in Command-by-Command NPort 6450-T 9 mode Overview The NPort® 6450 is a 4-port device server that uses the SSL and SSH protocols to transmit encrypted serial data over Ethernet. Up to 4 serial devices of any type can be connected to the NPort® 6450, with all four devices using the same IP address. The Ethernet port can be configured for a normal or secure TCP/IP connection. No Data Loss if Ethernet Connection Fails The NPort® 6450 is a reliable device server that provides users with secure serial-to-Ethernet data transmission and a customer-oriented hardware design. If the Ethernet connection fails, the NPort® 6450 will queue all serial data in its internal 64 KB port buffer. When the Ethernet connection is re-established, the NPort® 6450 will immediately release all data in the buffer in the order that it was received. Users can increase the port buffer size by installing a SD card. Terminal Servers > NPort® 6450 Series NPort 6450 Specifications Serial Communication Parameters Ethernet Interface Data Bits: 5, 6, 7, 8 Stop Bits: 1, 1.5, 2 Parity: None, Even, Odd, Space, Mark Flow Control: RTS/CTS, DTR/DSR, XON/XOFF Baudrate: 50 bps to 921.6 kbps (supports non-standard baudrates) Pull High/Low Resistor for RS-485: 1 kΩ, 150 kΩ Number of Ports: 1 Speed: 10/100 Mbps, auto MDI/MDIX Connector: 8-pin RJ45 Magnetic Isolation: 1.5 kV built-in Optical Fiber Interface (with network module) 100BaseFX Multi-mode Wavelength Max. TX Min. TX RX Sensitivity Link Budget 1300 nm -14 dBm -20 dBm -32 dBm 12 dB 5 kma Typical Distance 4 kmb -6 dBm Saturation a. 50/125 μm, 800 MHz*km fiber optic cable b. 62.5/125 μm, 500 MHz*km fiber optic cable c. 9/125 μm, 3.5 PS/(nm*km) fiber optic cable Serial Interface Serial Signals Single-mode RS-232: TxD, RxD, RTS, CTS, DTR, DSR, DCD, GND RS-422: Tx+, Tx-, Rx+, Rx-, GND RS-485-4w: Tx+, Tx-, Rx+, Rx-, GND RS-485-2w: Data+, Data-, GND 1310 nm 0 dBm -5 dBm -34 dBm 29 dB Memory Expansion Slot Slot Type: SD socket (supports up to 2 GB) Software 40 kmc -3 dBm Number of Ports: 4 Serial Standards: RS-232/422/485 Connector: DB9 male RS-485 Data Direction Control: ADDC® (Automatic Data Direction Control) Serial Line Protection: 15 kV ESD protection for all signals Console Port: Serial port 1 doubles as RS-232 console port Network Protocols: ICMP, IPv4/v6, TCP, UDP, DHCP, BOOTP, Telnet, DNS, SNMP V1/V2c/V3, HTTP, SMTP, ARP, PPPoE Security Protocols: DES, 3DES, AES, SSH, SSL Configuration Options: Web Console, Serial Console, Telnet Console, Windows Search Utility Windows Real COM Drivers: Windows 95/98/ME/NT/2000, Windows XP/2003/Vista/2008/7/8/8.1 (x86/x64), Windows 2008 R2/2012/2012 R2 (x64), Windows Embedded CE 5.0/6.0, Windows XP Embedded Fixed TTY Drivers: SCO Unix, SCO OpenServer, UnixWare 7, QNX 4.25, QNX 6, Solaris 10, FreeBSD, AIX 5.x, HP-UX 11i, Mac OS X Linux Real TTY Drivers: Linux 2.4.x, 2.6.x, 3.x [email protected] w w w. m o x a . c o m 9-13 Terminal Servers Standards and Certifications Management: SNMP MIB-II IP Routing: Static, RIP-I, RIP-II Operation Modes Standard: Real COM, TCP Server, TCP Client, UDP, Pair Connection, RFC2217, Terminal, Reverse Telnet, Ethernet Modem, Printer, PPP, Disabled Secure: Secure Real COM, Secure TCP Server, Secure TCP Client, Secure Pair Connection, SSH, Reverse SSH Applications Terminal Sessions: 8 sessions per port Physical Characteristics 9 Housing: Metal Weight: 1020 g Dimensions: Without ears: 158 x 103 x 35 mm (6.22 x 4.06 x 1.38 in) With ears: 181 x 103 x 35 mm (7.13 x 4.06 x 1.38 in) Safety: UL 60950-1, EN 60950-1 EMC: CE, FCC EMI: EN 55022 Class A, FCC Part 15 Subpart B Class A EMS: EN 55024, EN 61000-4-2 (ESD) Level 2/3, EN 61000-4-3 (RS) Level 2, EN 61000-4-4 (EFT) Level 2, EN 61000-4-5 (Surge) Level 2, EN 61000-4-6 (CS) Level 2, EN 61000-4-8 Level 1, EN 61000-4-11 Freefall: IEC-68-2-6, IEC-68-2-34, IEC-68-2-32 Vibration: IEC-68-2-6, IEC-68-2-34 Green Product: RoHS, CRoHS, WEEE Reliability Environmental Limits Alert Tools: Built-in buzzer and RTC (real-time clock) Automatic Reboot Trigger: Built-in WDT (watchdog timer) MTBF (mean time between failures): 120,354 hrs Terminal Servers > NPort® 6450 Series Operating Temperature: Standard Models: 0 to 55°C (32 to 131°F) Wide Temp. Models: -40 to 75°C (-40 to 167°F) Storage Temperature: -40 to 75°C (-40 to 167°F) Ambient Relative Humidity: 5 to 95% (non-condensing) Altitude: Up to 2000 m Warranty Warranty Period: 5 years Details: See www.moxa.com/warranty Note: Please contact Moxa if you require products guaranteed to function properly at higher altitudes. Pin Assignment Power Requirements Input Voltage: 12 to 48 VDC Power Consumption: 730 mA @ 12 V, 330 mA @ 24 V Alarm Contact: Relay output with current carrying capacity of 1 A @ 24 VDC Power Line Protection: 1 kV burst (EN 61000-4-4: EFT/B), 0.5 kV surge (EN 61000-4-5) PIN RS-232 RS-422/485-4w RS-485-2w 1 DCD TxD-(A) – DB9 male connector 2 RxD TxD+(B) – 1 2 3 4 5 3 TxD RxD+(B) Data+(B) 4 DTR RxD-(A) Data-(A) 5 GND GND GND 6 DSR – – 7 RTS – – 8 CTS – – 6 7 8 9 Dimensions Unit: mm (inch) 35 (1.38) 34 (1.34) O7 (0.28) 158 (6.22) 169 (6.65) 181 (7.13) Note: The LCD panel and push buttons are only available with standard temperature models. 9-14 w w w. m o x a . c o m [email protected] 25 (0.98) 12.5 (0.49) 103 (4.06) O 3.2 (0.13) Serial Connectivity Ordering Information Available Models NPort 6450: 4-port secure device server, RS-232/422/485 to Ethernet NPort 6450-T: 4-port secure device server, RS-232/422/485 to Ethernet, -40 to 75°C operating temperature Optional Accessories (can be purchased separately) Package Checklist • 1 NPort 6450 secure device server • 100 to 240 VAC power adapter (excluding T models) • Documentation and software CD • Quick installation guide (printed) • Warranty card DK-35A: Mounting kit for 35-mm DIN-Rail PWR-12150-USJP-SA-T: 100 to 240 VAC input, 12 VDC / 1.5 A output, screw-type, US/JP plug, -40 to 75°C operating temperature PWR-12150-EU-SA-T: 100 to 240 VAC input, 12 VDC / 1.5 A output, screw-type, EU plug, -40 to 75°C operating temperature PWR-12150-UK-SA-T: 100 to 240 VAC input, 12 VDC / 1.5 A output, screw-type, UK plug, -40 to 75°C operating temperature PWR-12150-CN-SA-T: 100 to 240 VAC input, 12 VDC / 1.5 A output, screw-type, CN plug, -40 to 75°C operating temperature PWR-12150-AU-SA-T: 100 to 240 VAC input, 12 VDC / 1.5 A output, screw-type, AU plug, -40 to 75°C operating temperature Use with the following NPort models Expansion Modules 6150 6250 6610-8 6650-8 6450 6610-16 6650-16 6610-32 6650-32 1 10/100BaseT(X) port – –     NM-TX02 NM-TX02-T 2 10/100BaseT(X) ports – –     NM-FX01-S-SC NM-FX01-S-SC-T 1 100BaseFX port, single mode, SC connector – –     NM-FX01-M-SC NM-FX01-M-SC-T 1 100BaseFX port, multi mode, SC connector – –     NM-FX02-S-SC NM-FX02-S-SC-T 2 100BaseFX ports, single mode, SC connector – –     NM-FX02-M-SC NM-FX02-M-SC-T 2 100BaseFX ports, multi mode, SC connector – –     NM-Modem NM-Modem-T 1 PSTN modem port, RJ11 connector – –     Terminal Servers > NPort® 6450 Series NM-TX01 NM-TX01-T 9 Note: Expansion modules can be purchased separately. [email protected] w w w. m o x a . c o m 9-15 Terminal Servers NPort® 6600 Series 8/16/32-port RS-232/422/485 rackmount secure terminal servers ››Up to 32 ports for high density environments ››Non-standard baudrates supported with high precision ››Port buffers for storing serial data when the Ethernet is off-line ››Supports IPv6 ››Ethernet redundancy (STP/RSTP/Turbo Ring) with network module ››Modular design for scalability ››DES/3DES/AES for highly secure data transmissions 9 Terminal Servers > NPort® 6600 Series Overview The NPort® 6600 series of secure device servers is the right choice for applications that use large numbers of serial devices packed into a small space. Security breaches are intolerable and the NPort® 6600 ensures data transmission integrity with support of EDS, 3DES, and AES encryption algorithms. Serial devices of any type can be connected to the NPort® 6600, and each serial port on the NPort® can be configured independently for RS-232, RS-422, or RS-485 transmission. LCD Panel Makes Configuration Easy The NPort® 6600 has a built-in LCD panel for configuration. The panel displays the server name, serial number, and IP address, and any of the device server’s configuration parameters, such as IP address, netmask, and gateway address, can be updated easily and quickly. Note: The LCD panel is only available with standard temperature models. Adjustable Resistor Values for RS-485 Communication 3 1 2 ON 3 1 2 ON 3 1 2 ON 3 1 2 ON 3 1 2 ON 3 1 2 ON 3 1 2 ON 3 1 2 ON 3 1 2 ON 3 1 2 ON 3 1 2 ON 3 1 2 ON 3 1 2 ON 3 1 2 ON 3 1 2 3 ON w w w. m o x a . c o m 2 9-16 ON DIP-Switches need adjusting to maintain the integrity of the electrical signal. Since no set of resistor values works for every environment, the NPort® 6600 allows manual adjustment of the resistor values for each serial port using built-in DIP switches. 1 The NPort® 6600 provides adjustable termination, pull high, and pull low resistors for RS-485 communication. In some critical environments, termination resistors may be needed to prevent the reflection of serial signals, and the pull high and pull low resistors may [email protected] Serial Connectivity Specifications Ethernet Interface Secure: Secure Real COM, Secure TCP Server, Secure TCP Client, Secure Pair Connection, SSH, Reverse SSH Number of Ports: 1 Speed: 10/100 Mbps, auto MDI/MDIX Connector: 8-pin RJ45 Magnetic Isolation: 1.5 kV built-in Applications Terminal Sessions: 8 sessions per port Physical Characteristics Optical Fiber Interface (with network module) Housing: Metal Weight: NPort 6600-8: 3460 g NPort 6600-16: 3580 g NPort 6600-32: 3600 g Dimensions: Without ears: 440 x 195 x 44 mm (17.32 x 7.68 x 1.73 in) With ears: 480 x 195 x 44 mm (18.9 x 7.68 x 1.73 in) 100BaseFX Wavelength Max. TX Min. TX RX Sensitivity Multi-mode Single-mode 1300 nm 1310 nm -10 dBm 0 dBm -20 dBm -5 dBm -34 to -30 dBm -36 to -32 dBm Link Budget 12 dB 29 dB Typical Distance 4 kma 40 kmb Saturation -6 dBm -3 dBm Environmental Limits a. 62.5/125 μm, 500 MHz*km fiber optic cable b. 9/125 μm, 3.5 PS/(nm*km) fiber optic cable Serial Interface Note: Please contact Moxa if you require products guaranteed to function properly at higher altitudes. Serial Communication Parameters Input Voltage: AC Models: 100 to 240 VAC DC Models: ±48 VDC (20 to 72 VDC, -20 to -72 VDC) Power Consumption: AC Models: 285 mA @ 100 VAC, 190 mA @ 240 VAC DC Models: 293 mA @ 48 VDC Alarm Contact: Relay output with current carrying capacity of 1 A @ 24 VDC Power Line Protection: 1 kV burst (EN 61000-4-4: EFT/B), 0.5 kV surge (EN 61000-4-5) Number of Ports: 8, 16, or 32 Serial Standards: NPort 6610: RS-232 NPort 6650: RS-232/422/485 Connector: 8-pin RJ45 RS-485 Data Direction Control: ADDC® (Automatic Data Direction Control) Serial Line Protection: 15 kV ESD protection for all signals Console Port: Dedicated RS-232 console port on rear panel (8-pin RJ45) Data Bits: 5, 6, 7, 8 Stop Bits: 1, 1.5, 2 Parity: None, Even, Odd, Space, Mark Flow Control: RTS/CTS, DTR/DSR, XON/XOFF Baudrate: 50 bps to 921.6 kbps (supports non-standard baudrates) Pull High/Low Resistor for RS-485: 1 kΩ, 150 kΩ Terminator for RS-485: 120 Ω Serial Signals RS-232: TxD, RxD, RTS, CTS, DTR, DSR, DCD, GND RS-422: Tx+, Tx-, Rx+, Rx-, GND RS-485-4w: Tx+, Tx-, Rx+, Rx-, GND RS-485-2w: Data+, Data-, GND Memory Expansion Slot Slot Type: SD socket (supports up to 2 GB) Software Network Protocols: ICMP, IPv4/v6, TCP, UDP, DHCP, BOOTP, Telnet, DNS, SNMP V1/V2c/V3, HTTP, SMTP, ARP, PPPoE Security Protocols: DES, 3DES, AES, SSH, SSL Configuration Options: Web Console, Serial Console, Telnet Console, Windows Search Utility Windows Real COM Drivers: Windows 95/98/ME/NT/2000, Windows XP/2003/Vista/2008/7/8/8.1 (x86/x64), Windows 2008 R2/2012/2012 R2 (x64), Windows Embedded CE 5.0/6.0, Windows XP Embedded Fixed TTY Drivers: SCO Unix, SCO OpenServer, UnixWare 7, QNX 4.25, QNX 6, Solaris 10, FreeBSD, AIX 5.x, HP-UX 11i, Mac OS X Linux Real TTY Drivers: Linux 2.4.x, 2.6.x, 3.x Management: SNMP MIB-II IP Routing: Static, RIP-I, RIP-II Operation Modes Power Requirements Standards and Certifications Safety: UL 60950-1, EN 60950-1 EMC: CE, FCC EMI: EN 55022 Class A, FCC Part 15 Subpart B Class A EMS: EN 55024, EN 61000-4-2 (ESD) Level 2/3, EN 61000-4-3 (RS) Level 2, EN 61000-4-4 (EFT) Level 2, EN 61000-4-5 (Surge) Level 2, EN 61000-4-6 (CS) Level 2, EN 61000-4-8 Level 1, EN 61000-4-11 Freefall: IEC-68-2-6, IEC-68-2-34, IEC-68-2-32 Vibration: IEC-68-2-6, IEC-68-2-34 Green Product: RoHS, CRoHS, WEEE 9 Terminal Servers > NPort® 6600 Series Operating Temperature: Standard Models: 0 to 55°C (32 to 131°F) Wide Temp. Models: -40 to 75°C (-40 to 167°F) Storage Temperature: -40 to 75°C (-40 to 167°F) Ambient Relative Humidity: 5 to 95% (non-condensing) Altitude: Up to 2000 m Reliability Alert Tools: Built-in buzzer and RTC (real-time clock) Automatic Reboot Trigger: Built-in WDT (watchdog timer) MTBF (mean time between failures): NPort 6610-8: 135,891 hrs NPort 6610-16: 102,373 hrs NPort 6610-32: 68,707 hrs NPort 6650-8: 135,370 hrs NPort 6650-16: 101,783 hrs NPort 6650-32: 68,177 hrs Warranty Warranty Period: 5 years Details: See www.moxa.com/warranty Standard: Real COM, TCP Server, TCP Client, UDP, Pair Connection, RFC2217, Terminal, Reverse Telnet, Ethernet Modem, Printer, PPP, Disabled [email protected] w w w. m o x a . c o m 9-17 Terminal Servers Dimensions and Pin Assignment Unit: mm (inch) 8-pin RJ45 connector 8 9 PIN RS-232 RS-422/ 485-4W 1 DSR (in) – – 2 RTS (out) TxD+ – GND 44 (1.73) 195 (7.68) 1 Standard model 31.8 (1.25) 440 (17.32) 462.6 (18.35) 480 (18.9) Wide temp. model RS-485-2w 3 GND GND 4 TxD (out) TxD- – 5 RxD (in) RxD+ Data+ Data- 6 DcD (in) RxD- 7 CTS (in) – – 8 DTR (out) – – Terminal Servers > NPort® 6600 Series Ordering Information Available Models Package Checklist NPort 6610-8: 8-port RS-232 to Ethernet secure terminal server, 100 to 240 VAC power input, 0 to 55°C • 1 NPort 6600 device server operating temperature • CBL-RJ45M9-150: 8-pin RJ45 to DB9 NPort 6610-8-48V: 8-port RS-232 to Ethernet secure terminal server, ±48 VDC power input, 0 to 55°C male connection cable, 150 cm operating temperature • Power cord (AC models only) NPort 6610-16: 16-port RS-232 to Ethernet secure terminal server, 100 to 240 VAC power input, 0 to • 2 rackmount ears 55°C operating temperature • Documentation and software CD NPort 6610-16-48V: 16-port RS-232 to Ethernet secure terminal server, ±48 VDC power input, 0 to 55°C • Quick installation guide (printed) operating temperature • Warranty card NPort 6610-32: 32-port RS-232 to Ethernet secure terminal server, 100 to 240 VAC power input, 0 to 55°C operating temperature NPort 6610-32-48V: 32-port RS-232 to Ethernet secure terminal server, ±48 VDC power input, 0 to 55°C operating temperature NPort 6650-8: 8-port RS-232/422/485 to Ethernet secure terminal server, 100 to 240 VAC power input, 0 to 55°C operating temperature NPort 6650-8-48V: 8-port RS-232/422/485 to Ethernet secure terminal server, ±48 VDC power input, 0 to 55°C operating temperature NPort 6650-16: 16-port RS-232/422/485 to Ethernet secure terminal server, 100 to 240 VAC power input, 0 to 55°C operating temperature NPort 6650-16-48V: 16-port RS-232/422/485 to Ethernet secure terminal server, ±48 VDC power input, 0 to 55°C operating temperature NPort 6650-32: 32-port RS-232/422/485 to Ethernet secure terminal server, 100 to 240 VAC power input, 0 to 55°C operating temperature NPort 6650-32-48V: 32-port RS-232/422/485 to Ethernet secure terminal server, ±48 VDC power input, 0 to 55°C operating temperature NPort 6650-8-T: 8-port RS-232/422/485 to Ethernet secure terminal server, 100 to 240 VAC power input, -40 to 75°C operating temperature NPort 6650-16-T: 16-port RS-232/422/485 to Ethernet secure terminal server, 100 to 240 VAC power input, -40 to 75°C operating temperature Optional Accessories (can be purchased separately) Serial Cables and Adapters: See Appendix A for details Expansion Modules 6150 6610-32 6650-32 NM-TX01 NM-TX01-T 1 10/100BaseT(X) port – –     NM-TX02 NM-TX02-T 2 10/100BaseT(X) ports – –     NM-FX01-S-SC NM-FX01-S-SC-T 1 100BaseFX port, single mode, SC connector – –     NM-FX01-M-SC NM-FX01-M-SC-T 1 100BaseFX port, multi mode, SC connector – –     NM-FX02-S-SC NM-FX02-S-SC-T 2 100BaseFX ports, single mode, SC connector – –     NM-FX02-M-SC NM-FX02-M-SC-T 2 100BaseFX ports, multi mode, SC connector – –     NM-Modem NM-Modem-T 1 PSTN modem port, RJ11 connector – –     Note: Expansion modules can be purchased separately. 9-18 Use with the following NPort models 6610-8 6610-16 6250 6450 6650-8 6650-16 w w w. m o x a . c o m [email protected] Serial Connectivity CN2600 Series 8 and 16-port RS-232/422/485 terminal servers with dual LAN redundancy ››LCD panel for easy IP address configuration (excluding wide temperature models) ››Dual-LAN cards with two independent MAC addresses and IP addresses ››Redundant COM function available when both LANs are active ››Dual-host redundancy can be used to add a backup PC to your system ››Dual AC power inputs ››Real COM/TTY drivers for Windows and Linux Redundancy is an important issue for industrial networks, and various types of solutions have been developed to provide alternative network paths when equipment or software failures occur. “Watchdog” hardware is installed to utilize redundant hardware-and a “Token”switching software mechanism is applied. The CN2600 terminal server uses its built-in Dual-LAN ports to implement a “Redundant COM” mode that keeps your applications running uninterrupted. Host Data A Data A Ethernet LAN A LAN B Data A Dual-LAN Redundancy The CN2600 has two separate LAN ports that can be connected to separate LAN networks. Dual-LAN redundancy involves setting up two separate physical networks to connect the PC host with the CN2600 (the PC host also requires two LAN cards). If one connection fails, the PC host can still communicate with your serial devices over the alternative LAN connection. Data A Terminal Servers > CN2600 Series Overview 9 Dual-LAN Redundancy Serial Data A RTU Host Redundant COM Moxa offers “Redundant COM”, an easy-to-use application to provide an alternative solution for network redundancy. When the CN2600 receives a data packet from a connected device, two identical data packets are sent over two independent LAN connections to prevent lost data packets if one LAN connection becomes unavailable. The CN2600 software is programmed to automatically discard duplicate data packets. Data A LAN A e r Failu Ethernet LAN B Data A Data A Redundant COM Serial Dual-host Redundancy The CN2600’s dual LAN cards can also be used to set up “dualhost” redundancy. In this case, both networks (LAN A and LAN B in the figure) are connected to two different hosts. If either of the two hosts shuts down unexpectedly, the other host will still be able to communicate with serial devices connected to the CN2600. Host 1 Data A RTU Host 2 Data A Data A Data A Ethernet LAN A LAN B Data A Data A Dual-host Redundancy Serial RTU [email protected] w w w. m o x a . c o m 9-19 Terminal Servers Dual-AC Model Supported UPS Dual-power redundancy uses two power inputs and redundant internal power supplies to ensure that all of the CN2600’s functions will be available, even in the event of power circuit failures. UPS UPS UPS Power Cord Power Cord re Failu Appearance 9 LED indicators system status, serial Tx/Rx IP configuration buttons Reset button Terminal Servers > CN2600 Series Serial ports 8-pin RJ45, RS-232/422/485, 50 to 921.6 kbps LCD panel AC power input 100 to 240 VAC input, 47 to 63 Hz Ground Ethernet ports RJ45 10/100 Mbps Note: LCD panel and configuration buttons are not available for wide temperature models Specifications Ethernet Interface Number of Ports: 2 (2 IPs) Speed: 10/100 Mbps, auto MDI/MDIX Connector: 8-pin RJ45 Magnetic Isolation: 1.5 kV built-in Serial Interface Number of Ports: 8 or 16 Serial Standards: CN2610: RS-232 CN2650/2650I: RS-232/422/485 Connector: CN2610/2650: 8-pin RJ45 CN2650I: DB9 male RS-485 Data Direction Control: ADDC® (Automatic Data Direction Control) Serial Line Protection: 15 kV ESD protection for all signals 2 kV optical isolation (CN2650I) Console Port: Dedicated RS-232 console port on rear panel (8-pin RJ45) Serial Communication Parameters Data Bits: 5, 6, 7, 8 Stop Bits: 1, 1.5, 2 Parity: None, Even, Odd, Space, Mark Flow Control: RTS/CTS, DTR/DSR, XON/XOFF Baudrate: 50 bps to 921.6 kbps Pull High/Low Resistor for RS-485: 1 kΩ, 150 kΩ Terminator for RS-485: 120 Ω Serial Signals Software Network Protocols: ICMP, IPv4, TCP, UDP, DHCP, BOOTP, Telnet, DNS, SNMP, HTTP, SMTP, ARP, PPPoE, DDNS Security Protocols: RADIUS, HTTPS, SSH, PAP, CHAP Configuration Options: Web Console, Serial Console, Telnet Console, Windows Search Utility w w w. m o x a . c o m Windows Real COM Drivers: Windows 95/98/ME/NT/2000, Windows XP/2003/Vista/2008/7/8/8.1 (x86/x64), Windows 2008 R2/2012/2012 R2 (x64), Windows Embedded CE 5.0/6.0, Windows XP Embedded Fixed TTY Drivers: SCO Unix, SCO OpenServer, UnixWare 7, QNX 4.25, QNX 6, Solaris 10, FreeBSD, AIX 5.x, HP-UX 11i, Mac OS X Linux Real TTY Drivers: Linux 2.4.x, 2.6.x, 3.x Management: SNMP MIB-II IP Routing: Static, RIP-I, RIP-II Operation Modes Standard: Real COM, TCP Server, TCP Client, UDP, RFC2217, Terminal, Reverse Telnet, PPP, DRDAS, Redundant COM, Disabled Applications Terminal Sessions: 8 sessions per port Physical Characteristics Housing: Metal Weight: CN2610-8-2AC: 3760 g CN2610-16-2AC: 3810 g CN2650-8: 3740 g CN2650-16: 3790 g CN2650-8-2AC: 3900 g CN2650-16-2AC: 3980 g CN2650I-8: 3666 g CN2650I-16: 3776 g CN2650I-8-2AC: 3932 g CN2650I-16-2AC: 4022 g Dimensions: Without ears: 440 x 198 x 45.5 mm (17.32 x 7.80 x 1.77 in) With ears: 480 x 198 x 45.5 mm (18.9 x 7.80 x 1.77 in) Environmental Limits RS-232: TxD, RxD, RTS, CTS, DTR, DSR, DCD, GND RS-422: Tx+, Tx-, Rx+, Rx-, GND RS-485-4w: Tx+, Tx-, Rx+, Rx-, GND RS-485-2w: Data+, Data-, GND 9-20 RS-232 console port Operating Temperature: Standard Models: 0 to 55°C (32 to 131°F) Wide Temp. Models: -40 to 75°C (-40 to 167°F) Storage Temperature(with package): -20 to 70°C (-4 to 158°F) Ambient Relative Humidity: 5 to 95% (non-condensing) Altitude: Up to 2000 m Note: Please contact Moxa if you require products guaranteed to function properly at higher altitudes. [email protected] Serial Connectivity Power Requirements Input Voltage: 100 to 240 VAC, 47 to 63 Hz Power Consumption: 235 mA @ 100 VAC, 145 mA @ 240 VAC Power Line Protection: 1 kV burst (EN61000-4-4: EFT/B), 2 kV surge (EN61000-4-5) Standards and Certifications Safety: UL 60950-1, EN 60950-1 EMC: CE, FCC EMI: EN 55022 Class A, FCC Part 15 Subpart B Class A EMS: EN 55024, EN 61000-4-2 (ESD) Level 4, EN 61000-4-3 (RS) Level 3, EN 61000-4-4 (EFT) Level 4, EN 61000-4-5 (Surge) Level 2, EN 61000-4-6 (CS) Level 2, EN 61000-4-8 Level 4, EN 61000-4-11 Freefall: IEC-68-2-34, IEC-68-2-32 Vibration: IEC-68-2-6 Green Product: RoHS, CRoHS, WEEE Reliability Alert Tools: Built-in buzzer and RTC (real-time clock) Automatic Reboot Trigger: Built-in WDT (watchdog timer) MTBF (mean time between failures): 99,302 hrs Warranty Warranty Period: 5 years Details: See www.moxa.com/warranty Dimensions Pin Assignment Unit: mm (inch) 3 4 5 6 7 8 9 10 11 12 13 14 15 16 462.6 (18.21) CN2600 Series (Standard Model) 1 SEL 2 3 4 5 TX Ready RX 6 7 8 5.6 (0.22) 9 10 11 12 13 14 15 16 197.5 (7.78) 440 (17.32) 45.5 (1.79) 2 RX 8.7 (0.34) 31.8 6.85 (0.27) (1.25) 1 TX Ready PIN RS-232 RS-422/485-4w RS-485-2w 1 DSR – – 2 RTS TxD+(B) – 3 GND GND GND 4 TxD TxD-(A) – 5 RxD RxD+(B) Data+(B) 6 DCD RxD-(A) Data-(A) 7 CTS – – 8 DTR – – 1 2 3 4 5 DB9 male connector 6 7 8 9 CN2610/2650 CN2650I PIN RS-232 RS-422/485-4w RS-485-2w 1 DCD TxD-(A) – 2 RxD TxD+(B) – 3 TxD RxD+(B) Data+(B) 4 DTR RxD-(A) Data-(A) 5 GND GND GND 6 DSR – – 7 RTS – – 8 CTS – – 9 Terminal Servers > CN2600 Series CN2650-16-T (Wide Temp. Model) 8 1 8-pin RJ45 connector Ordering Information Available Models Package Checklist CN2610-8-2AC: Dual-LAN, dual-AC-power terminal server with 8 RS-232 ports, 0 to 55°C operating • 1 CN2600 terminal server temperature • CBL-RJ45F9-150: 8-pin RJ45 to DB9 CN2610-16-2AC: Dual-LAN, dual-AC-power terminal server with 16 RS-232 ports, 0 to 55°C female connection cable, 150 cm operating temperature • Power cords (2AC model has 2pcs) CN2650-8: Dual-LAN terminal server with 8 RS-232/422/485 ports, 0 to 55°C operating temperature • Documentation and software CD CN2650-16: Dual-LAN terminal server with 16 RS-232/422/485 ports, 0 to 55°C operating • Quick installation guide (printed) temperature • Warranty card CN2650-8-2AC: Dual-LAN, dual-AC-power terminal server with 8 RS-232/422/485 ports, 0 to 55°C operating temperature CN2650-16-2AC: Dual-LAN, dual-AC-power terminal server with 16 RS-232/422/485 ports, 0 to 55°C operating temperature CN2650I-8: Dual-LAN terminal server with 8 RS-232/422/485 ports and 2 kV optical isolation, 0 to 55°C operating temperature CN2650I-16: Dual-LAN terminal server with 16 RS-232/422/485 ports and 2 kV optical isolation, 0 to 55°C operating temperature CN2650I-8-2AC: Dual-LAN, dual-AC-power terminal server with 8 RS-232/422/485 ports and 2 kV optical isolation, 0 to 55°C operating temperature CN2650I-16-2AC: Dual-LAN, dual-AC-power terminal server with 16 RS-232/422/485 ports and 2 kV optical isolation, 0 to 55°C operating temperature CN2650-8-2AC-T: Dual-LAN, dual-AC-power terminal server with 8 RS-232/422/485 ports, -40 to 75°C operating temperature CN2650-16-2AC-T: Dual-LAN, dual-AC-power terminal server with 16 RS-232/422/485 ports, -40 to 75°C operating temperature [email protected] w w w. m o x a . c o m 9-21 This page intentionally left blank.

Termin Lov Servery řady Nport 6000 A Cn2600

Rating

Date

Size

Views

Categories

Share

Transcript

Forgot your password?.