Transcript
Bagless Cylinder Vacuum Cleaner VCBL1411
USER GUIDE
VCBL1411 Vacuum Cleaner User Guide IMPORTANT SAFETY INFORMATION To reduce the risk of fire, electrical shock, or injury: $ Read all the instructions carefully before using your appliance and keep them for future reference. If you pass the product on to a third party, include this manual. $ Unplug the appliance from the mains supply when not in use, removing or attaching filters, accessories, the dust cup and before cleaning any part of the appliance. $ When unplugging, hold the plug top, not the power cord. $ Do not immerse the body of the cleaner or the electrical cord or plug in water or liquids. $ Never leave the cleaner unattended when it is connected to the electricity supply. $ Do not use outdoors in damp or wet weather $ Do not use your appliance indoors in damp or wet conditions. $ Do not use attachments or accessories not recommended by the manufacturer. $ Close supervision is necessary when an appliance is used near children. Children should not operate this appliance. $ This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. $ Children should be supervised to ensure that they do not play with the appliance. $ This appliance is for household use. Do not use for any
$ $ $ $ $ $
purpose not expressly specified in this manual. There are no user serviceable parts in this appliance. Unauthorised dismantling or servicing will void the warranty. If the supply cord is damaged, it must be replaced by the manufacturer or its service agent or a similarly qualified person in order to avoid a hazard Refer all servicing which involves the taking or putting on of parts (other than those specifically referred to in this manual), to a qualified repair person or approved service centre. Do not use attachments or accessories which are not recommended by the manufacturer. They may cause malfunction or injury. Do not use harsh abrasives, or caustic cleaners when cleaning this appliance. Store the appliance away from direct sunlight, with all accessories detached and out of the reach of children.
Electrical Information Before using this appliance ensure that the voltage of your electricity supply is the same as that indicated on the rating plate of the appliance. .
SPECIFICATIONS Model: Voltage: Power: Net Weight:
VCBL1411 220-240 V AC 50Hz 1200W (nom):1400W( max) 4.0 Kg
Class II construction double insulated. This product must not be connected to earth.
! When operating your cleaner: $ Do NOT use the vacuum cleaner if it has been dropped, $ $ $ $ $ $ $ $ $ $
$ $ $ $ $ $
damaged, left outdoors, or dropped into water. Do NOT pull or carry the cleaner by the cord, close a door on the cord, or pull the cord around sharp edges or corners. Use the handle to carry and move the cleaner. Do NOT run the appliance over the power cord. Do NOT handle the mains plug or cleaner with wet hands. Do NOT use the vacuum cleaner to pick up large objects or objects that are likely to damage the vacuum cleaner. Do NOT attempt to vacuum long hair, string, pieces of cloth, etc. when vacuuming carpets or floors. These may clog the vacuum cleaner. Keep hair, loose clothing, jewellery, fingers, feet and all parts of your body away from openings and moving parts. Do NOT vacuum hot items; e.g. cigarettes, matches, ashes. Do NOT vacuum hard or metal objects, nails pins, etc. Do NOT pick up toxic, or flammable materials or use in
$ $ $ $ $
the presence of explosive or toxic dust, liquids or vapour. Use only on dry, indoor surfaces. Do NOT put any objects into openings. Do NOT use with any filters blocked. Do NOT use without all the filters in place. Empty the Dust Cup before it reaches the MAX level. Switch the cleaner off before plugging or unplugging the vacuum cleaner into the mains supply. Use extra care when vacuuming on stairs. Keep all vents openings and attachments free of dust, lint, hair and anything else that may reduce air flow. Keep the end of the hose and all attachments away from your face and body. If the appliance becomes clogged, switch off and unplug the power cord before clearing the obstruction. NEVER leave the cleaner unattended while it is plugged into the mains
IMPORTANT NOTICE - PLEASE READ BEFORE USING THIS PRODUCT!
!
THIS CLEANER WORKS BY SUCKING AIR AT HIGH PRESSURE THROUGH A POWERFUL MOTOR. FOR EFFICIENT AND SAFE OPERATION IT IS ESSENTIAL THAT ALL THE AIRWAYS AND FILTERS ARE CLEANED AT REGULAR INTERVALS AND THAT THE DUST IS EMPTIED BEFORE THE DUST CONTAINER IS FULL AND AFTER EVERY USE OF THE APPLIANCE. FAILURE TO CLEAN THE FILTERS AND EMPTY THE DUST CONTAINER WILL RESTRICT THE AIRFLOW. THIS WILL RESULT IN POOR CLEANER PERFORMANCE. LONG TERM NEGLECT WILL BLOCK THE AIRFLOW AND MAY DAMAGE THE CLEANER BEYOND REPAIR. ANY DAMAGE CAUSED BY FAILURE TO CLEAN THE FILTERS, AIRWAYS AND DUST CONTAINER AS SPECIFIED IN THESE INSTRUCTIONS WILL NOT BE COVERED BY THE WARRANTY. Page 2
VCBL1411 Vacuum Cleaner User Guide Your Vacuum Cleaner and its accessories
Mains ON/OFF Switch
Dust Cup Release
Carry Handle
Cord Rewind Switch (under Handle)
Hose Inlet
Cord Storage Compartment
Air Outlet Filter Cover
Dust Cup Filter Dust Cup
Storage Hook
Furniture Tool Extension Tubes Floor Brush
Hose Collar Flexible Hose Handle
Flexible Hose
Unpacking The Cleaner Remove all packaging from the appliance and accessories. Retain the packaging. If you dispose of it, do so according to any recycling regulations. Identify the cleaner components from the illus-trations. If any items are missing or damaged, contact your nearest Tesco store for assistance. Please have your receipt ready when you call.
Page 3
VCBL1411 Vacuum Cleaner User Guide Assembling your Vacuum Cleaner Never attach or remove accessories when the vacuum cleaner is switched on.
Attaching and Removing the Flexible Hose
V
To Attach:
To Remove:
Push the collar firmly into the Hose Inlet and check that the collar snaps into place.
Press the spring latch in and remove the hose.
Attaching the Hose Extensions
Attach the Floor Brush (if required)
You can use the cleaner using only the hose or with one or both extension tube/s fitted.
Attach the Furniture Tool in the same way.
Attach the handle to one tube Attach the second tube similarly as required
Parking the Attachments
Carrying the Cleaner Always carry the cleaner by the handle.
You can park the floor brush when you are not using it on the Storage Hook located at the rear of the cleaner. You can also store the cleaner with the tube/s connected to the floor brush which is in turn attached to the hook.
Page 4
VCBL1411 Vacuum Cleaner User Guide Operating your Vacuum Cleaner 1:`To extend the power cord: Gently pull the cord from the recess located in the rear of the cleaner. The cord has two marks.
Using the Accessories
2
The Floor Brush is adjustable for use on carpets or bare floors. Bare Floors: Press the lever showing the Brush Symbol. The brush will appear.
The yellow mark shows the maximum safe length to which you can extend the cord. If you can see the red mark the cord has been lengthened too much. Never extend the cord beyond the red mark or you may damage the cord winding mechanism.
1
2: To rewind the cord: Unplug the cord. The handle incorporates the Cord Release. Press the handle down. Gently guide the cord back by hand into the cleaner until it is fully rewound. Do not let the cord return unaided or it may whip and cause damage or injury.
Carpets: Press the lever showing the Floor symbol to retract the floor brush.
The Furniture Tool is a dual-purpose tool. Use it to vacuum cushions, etc. The tool can be used with the brush on or it can be removed if required removed for greater versatility.
Slide on/off as required
Using the Appliance Make sure the dust cup is empty! (see Page 6) Fit the appropriate attachments. Extend the power cord to a usable length. Plug the mains plug into the mains point. Press the Mains ON/OFF switch to switch the power ON. (Press again to switch the power OFF)
General Do's and Don'ts
Setting the Suction Power. The suction power can be increased or decreased by operating the airflow slider in the hose grip. Use a low setting for curtains and delicate fabrics.Use a medium setting for long pile and velour carpets or soft textile flooring tiles. Use a high setting for rough short pile carpets, coir matting and rugs, and hard bare floors.
Do NOT attach or remove accessories when the vacuum cleaner is switched on. Do NOT pull the cleaner around the room by the hose. Do NOT over extend the hose. Trying to reach beyond the hose length could cause an accident. Be especially careful on stairs. Do NOT pull or carry the cleaner by the cord, close a door on the cord, or pull the cord around sharp edges or corners. Do not over extend the cord. Switch the cleaner off and move it to a closer power point. Use just enough cord to do the job. Use the carry handle to lift or move the cleaner. If you are moving the cleaner a long way or up a flight of stairs, switch off, rewind the power cord and park the accessories. Examine the dust level and empty the dust cup regularly. NEVER let the dust exceed the MAX level (See Page 6). When you have finished vacuuming:
$ $ $ $
Switch off and unplug the appliance. Rewind the power cord. Empty the dust cup and clean the dust cup filters. Disconnect the accessories and store the cleaner in the vertical position or place the cleaner normally with the accessories in the parked position. (See Storage)
Clearing a Blockage If the cleaner loses suction and the dust in the dust cup is below the MAX mark, this may be due to clogged filters or a blockage. DO NOT operate if the suction is impaired. $
When vacuuming: Move the vacuum head back and forth over the surface. Use even strokes. Do not press- let the cleaner do the work.
$
Page 5
If you suspect a blockage: Switch off and unplug immediately. Empty the dust, check and clean the filters. If this does not remove the blockage: Check the extension tubes and accessories visually and remove any blockage with a stick or broom handle.
VCBL1411 Vacuum Cleaner User Guide Emptying the Dust Cup and Cleaning the Dust Cup Filters Empty the dust cup regularly to maintain the efficient performance of the cleaner.
Cleaning the Dust Cup Filter The HEPA Filter stops nearly all dust particles and airborne allergens from re-entering the air you breathe. The HEPA Filter stops nearly all dust particles and airborne allergens from re-entering the air you breathe. When you have finished vacuuming you must clean the dust cup filter. This is essential
The maximum dirt level is marked on the Dust Cup.
Open the Dust Cup. Hold the funnel tube of the filter assembly. Rotate the tube to the left (anti-clockwise) to unlock it. Lift the filter assembly out.
UNLOCK UNLOCK You must empty the Dust Cup before the dirt reaches the MAX mark. Failure to do this will impair the efficiency of the cleaner. Switch the cleaner off and unplug it. Press the lid release down and lift the lid up
LOCK
LOCK Tap the filter on the edge of a bin to shake off any excess dust.
Carefully remove the dust cup from the cleaner. Invert the dust cup over a bin. Press the catch on the lid which will pop open. Shake and tap the dust cup lightly to remove as much dust as possible. Close the lid. If you are still vacuuming, replace the cup. Brush out the HEPA filter with a soft brush. If the filter is soiled, wash it under running water until it is thoroughly clean. Allow the filter to dry and then re insert it into the Dust Cup. NEVER replace a filter if it is damp.
Page 6
VCBL1411 Vacuum Cleaner User Guide Cleaning the Inlet Filter
Cleaning the Exhaust Filter
The Inlet filter is inside the cleaner. Whenever you remove the Dust Cup, you should inspect this filter and clean it.
The Exhaust filter is located at the rear of the cleaner, This filter should be cleaned regularly, and whenever it shows any signs of dirt. Press down on the filter cover. Hinge it out and remove it
This filter should be cleaned regularly, and whenever it shows any signs of dirt. Lift the filter out, brush it thoroughly and if necessary wash it under running water. Allow to dry fully.
Lift the filter out , and wash it under running water. Allow to dry fully.
If there is any dirt around the inlet cavity carefully brush it out. This will help keep the internal airways clean and maintain top cleaner performance. When the filter is thoroughly dry replace it in the inlet. Press the filter firmly in to ensure it is firmly trapped in place by the two tetaining tabs in the inlet cavity. NEVER replace a filter when it is wet or even damp.
Brush the outlet cavity out. This will help keep the internal airways clean and maintain cleaner performance. When the filter is dry, replace it in the cage. The filter is a a two-part unit. When replacing the filter the smooth side should be facing out. NEVER replace a filter when it is wet or even damp.
It is essential to inspect clean the filters regularly. The period between inspections will depend on how often and for how long you use the cleaner. The filter in the dust cup should be cleaned whenever you empty the dust. The motor inlet and exhaust filters should be checked after every three cleaning sessions. If the cleaner shows any sign of losing suction, switch off, check and clean the filters and if necessary, clear any blockage. NEVER operate the cleaner with clogged filters, you could damage the cleaner motor. If a filter shows any sign of wear or damage, or clogging that ordinary cleaning cannot remove it should be replaced. Contact the Tesco helpline number on the last page of this manual for assistance.
Page 7
VCBL1411 Vacuum Cleaner User Guide OPERATING CAUTIONS $ NEVER operate the cleaner with damaged filters or with a filter missing $ Use approved filters and regularly clean and replace them. $ If an obstruction occurs during cleaning: Turn the cleaner OFF and unplug. Check the dust level. Empty the dust cup. Check the hose and the tubes for blockage and clear these manually following the instructions previously given..
AUTOMATIC SHUT-OFF SWITCH There is a safety switch inside the cleaner to prevent the unit from being run with too high a vacuum rate. If the airways or filters get clogged the pressure in the cleaner will be excessive and the safety switch will be turned on. The cleaner then will stop working to protect the motor from overheating. If this happens switch off and unplug the cleaner immediately. Allow the motor to cool down for one hour and clean the airways and filters thoroughly. Plug the cleaner in again and switch on: the cleaner should now operate normally. NOTE: Repeated and excessive use of the cleaner in a blocked or semi-blocked state may cause the motor to fail permanently.
When you have finished Vacuuming: Switch the cleaner off and unplug from the mains. Empty the dust cup and clean the dust cup filters Wipe the cleaner body with a damp cloth and dry thoroughly. Do NOT allow water or liquids to penetrate the vacuum cleaner. This could be dangerous. Store the cleaner safely out of the reach of children and pets. The cleaner can be stored upright on its base with the hose and accessories disconnected and separately stored. Although the cleaner may be stored fully assembled with the brush in the parked position this is not recommended.
UK: Waste electrical products should not be disposed of with household waste. Separate disposal facilities exist, for your nearest facilities see www.recycle-more.co.uk or in-store for details.
Service and spares If you have difficulty obtaining replacement spares, filters, etc. contact the TESCO electrical help line on 0845 456 6767. Please have your purchase receipt with you when you call.
ROI: Produced after 13th August 2005. Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your Local Authority or retailer for recycling advice.
Warranty This appliance is intended only for household use. It must be properly installed and operated in accordance with these instructions. Failure to do this will invalidate the warranty. Your appliance is covered by a warranty for 12 months from the date of purchase. If a fault develops during this period, please return the unit to your nearest Tesco store together with the original receipt as proof of purchase. This warranty in no way affects your consumer rights
Tesco Stores Ltd, Delamare Road, Cheshunt, Herts, EN8 9SL
Helpline: 0845 456 6767 (Calls cost up to 4p per minute from a BT landline, other providers may vary) 8 Page 6
