Transcript
INSTALLATION MANUAL
Tilting Wall Mount
3. Hanging the TV onto the Wall Plate wall
wall
Bolt
Tighten the two bolts by using a proper phillips screwdriver to secure the adapter brackets to the wall plate.
4. Adjustment
Tilt adjusting knob
0° -10°
CAUTION: DO NOT EXCEED RATED LISTED WEIGHT. SERIOUS INJURY OR PROPERTY DAMAGE MAY OCCUR!
Loosen the adjusting knobs to tilt the TV to obtain desired angle then tighten them.
TFE23-46-BK
200x200/300x300 400x200/400x400
46" MAX
50kg (110lbs) RATED
Maintenance • Check that the bracket is secure and safe to use at regular intervals(at least every three months). • Please contact your distributor if you have any questions.
7
NOTE: Read the entire instruction manual before you start installation and assembly.
Component Checklist IMPORTANT: Ensure that you have received all parts according to the component checklist prior to installation. If any parts are missing or faulty, telephone your local distributor for a replacement.
WARNING • Do not begin the installation until you have read and understood all the instructions and warnings contained in this installation sheet. If you have any questions regarding any of the instructions or warnings, please contact your local distributor. • This mounting bracket was designed to be installed and utilised ONLY as specified in this manual. Improper installation of this product may cause damage or serious injury. • This product should only be installed by someone with good mechanical ability who has basic building experience and fully understands this manual.
wall plate (x1) A
left adapter bracket (x1) B
right adapter bracket (x1) C
Package M
• Make sure that the supporting surface will safely support the combined weight of the equipment and all attached hardware and components. • If mounting to wood wall studs, make sure that mounting screws are anchored into the center of the studs. The use of a stud finder is highly recommended.
M5x14 (x4) M-A
M6x14 (x4) M-B
M8x20 (x4) M-C
M6x30 (x4) M-D
• Always use an assistant or mechanical lifting equipment to safely lift and position the equipment. • Tighten screws firmly, but do not over tighten. Over tightening can cause damage to the items, This greatly reduces their holding power.
M8x30 (x4) M-E
washer (x4) M-F
small spacer (x8) M-G
big spacer (x4) M-H
• This product is intended for indoor use only. Using this product outdoors could lead to product failure and personal injury. Package W
ST6.3x55 (x4) W-A
1
concrete anchor (x4) W-B
D6 washer (x4) W-C
2
1b. For Solid Brick and Concrete Mounting
1a. For Wood Stud Wall Mounting 55mm ((2.2" (2.2") 2.2"))
60mm ((2.4") 2.4") ø 4.5mm (ø 3/16")
1
ø 10mm (ø 3/8" ) Mark the exact 1 location of mounting holes
2
2 Find and mark the exact location of mounting holes
3
Drill pilot holes Drill pilot holes
√
X
√
X
X
X
X W-B
Screw the wall plate onto the wall
W-A
Screw the wall plate onto the wall W-C W-A
W-C
WARNING • Make sure that mounting screws are anchored into the center of the studs. The use of a stud finder is highly recommended.
WARNING
• Installers are responsible to provide hardware for other types of mounting situations. • Installers must verify that the supporting surface will safely support the combined weight of the equipment and all attached hardware and components.
3
Installers must verify that the supporting surface will safely support the combined weight of the equipment and all attached hardware and components.
4
2. Installing the Adapter Brackets
2-2 For Recessed Back Screens or to Access A/V Inputs
TV
TV
TV
Top of the TV
M-C
M-C / M-D/M-E
M-D/M-E
M-D/M-E
2-1 For Flat Back Screens
TV TV
TV
M-A M-B M-C
M-F
M-G
M-F
or M-G
M-F
or
M-G
M-H
M-F
or M-G
M-H
M-F
Note: Choose the appropriate screws, washers and spacers (if necessary) according to the type of screen.
· Position the adapter brackets as close as possible to the center of the TV. · Screw the adapter brackets onto the TV. Tighten all screws but do not over tighten.
5
6
