Transcript
Compact Video, Audio and Optical Converters
Up to 6 BrightEye units in 1RU. All BrightEyes are 5.625” wide and either 0.8” or 1.7” high.
Over 50 Units to Choose From The BrightEye™ line of compact converters from Ensemble Designs takes advantage of the newest technology to bring you the best video and audio converters. With over 50 different BrightEye units to choose from, you’ll find the right unit for your video processing needs. These self-contained converters interface to a full range of video formats: high definition and standard definition SDI, 3 Gb/s, analog component, analog composite, and Y/C (S-Video). Analog audio and AES digital audio converters and embedders round out the BrightEye family. Additionally, with fiber optic I/O choices, BrightEye can take you farther than any ordinary converter.
Proven and Reliable Whether you’re upconverting analog video to HD for a projection system, converting a camera feed to fiber in an arena, or feeding HD Tri-Level Sync to a non-linear editor, BrightEye is there to help. With their multi-format inputs and outputs, BrightEye converters are the flexible and cost-effective answer to any conversion requirement. BrightEye’s easy configuration interface and signal status indicators make it simple to install and troubleshoot a system.
BrightEye Mac and PC Software Adjusting video levels, output timing and mixing audio channels are so easy with BrightEye control software. No DIP switches or button hold-downs are needed. Use BrightEye Mac or PC software to control a single BrightEye unit or any number of units connected to a USB hub. Additionally, you can use it to upgrade BrightEye units as new software versions become available. BrightEye Mac and PC software are included with each unit at no charge.
Used Worldwide Their compact size lets you put conversion right where it’s needed: in a production, on a helicopter, or in a boardroom. Reliable and easy to install, these units make your transition to HD simple. And they’re affordable too!
Mac Screen Shot 2
Table of Contents BrightEye Mitto 3G/Fiber/HD/SD Scan Converters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 New BrightEye NXT 410 Clean HDMI Router . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 New BrightEye NXT 415 Compact Router. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 New BrightEye NXT 430 Clean Compact Router. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 BrightEye 5 Analog Composite TBC and Frame Sync . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 BrightEye 25 Analog Video/Audio to SD SDI Converter with TBC and Embedder. . . . . . . . . . . 18 BrightEye 46 3G/HD/SD/ASI Electrical to Optical Converter. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 BrightEye 72 3G/HD/SD SDI to HDMI Converter. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 BrightEye 72-F Optical 3G/HD/SD SDI to HDMI Converter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 BrightEye 75 HD/SD Analog to Digital Video Converter. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 BrightEye 81 3G/HD/SD SDI to HDMI Converter. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 BrightEye 83 HDMI to 3G/HD/SD SDI Converter. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 BrightEye 83-F Optical to HDMI and 3G/HD/SD SDI Electrical Converter. . . . . . . . . . . . . . . . . . . . . 33 BrightEye 90 HD Up/Down/Cross Converter and ARC with AES Audio. . . . . . . . . . . . . . . . . . . . . 34 BrightEye 90-A HD Up/Down/Cross Converter and ARC with Analog Audio. . . . . . . . . . . . . . . . . . 38 BrightEye 91 HD Upconverter with AES Audio. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
3
BrightEye Mitto 3G/Fiber/HD/SD Scan Converters YouTube and Skype Video Made Easy
Easy To Use
The BrightEye Mitto™ family of high performance scan converters provide a new way to take just about any source to 3G, HD or SD SDI video. Computer video can now be used for the most demanding applications including corporate events, high-end military, medical, classroom, church and broadcast. All Mitto units accept VGA, DVI and HDMI input signals from PC and Mac computers.
BrightEye PC/Mac software runs overtop of any video, website or software. The Selection Tool shows up as a box around your selection and shows the portion of the video that will be output from BrightEye Mitto.
Choose the Functionality You Need Six different BrightEye Mitto units, each with varying types of outputs and capabilities, allow you to choose the best one for your particular video application. All BrightEye Mitto units convert YouTube, Skype video, PowerPoint presentations, emails and maps to video. Ensemble uses the latest technology in its proprietary upconversion and filtering and that means you have the best looking video. Compare Mitto to any other scan converter and see the difference!
Use a Mouse to Select What's Output to Video BrightEye™ PC and BrightEye Mac software let you simply use your mouse to click and drag over the specific portion of computer video that you want to output. The perspective of seeing the whole screen gives you the ability to choose exactly which portion of the video you want to output. It’s easy to output the entire screen or just a selected portion. Resize the selection window by clicking and dragging with your mouse. Mitto’s video output automatically goes to pillarbox or letterbox as needed. Mitto automatically maintains perfect aspect ratio.
BrightEye Mac and PC Software Adjusting video levels, output timing, audio delay, and mixing audio channels is so easy with BrightEye control software. From the software you have complete and intuitive control of timing, video format, and video level adjustments. You can easily time BrightEye Mitto into a screen scaler, video production switcher or router.
Features • High Performance Scan Converter for PC and Mac
• Auto senses DVI or VGA
• Best way to bring PowerPoint™ YouTube™, Skype™, Maps and Emails to Video for Production Use
• Choose a Mitto with Adjustable Audio Delay for Skype and On-line Video Applications
• Superior Quality – Proprietary Scaling and Filtering System Provides Maximum Detail, Flicker-Free Video Output
• Use a Mouse to Select the Part of the Video You Want to Output
• Use with all Types of Macs and PCs including Laptops, iPhone® and iPad™ • Intuitive Front Panel Controls • Output Choices: 1.5 and 3 Gb/s HD, SD SDI, Composite Video, Fiber Optic • DVI I/O, VGA and HDMI Support with an Adapter
4
• Easily Adjust Video Parameters and Select Video Output Format • Genlock and Time to House Reference, Fully Timeable • Rackmountable • Memory Presets for Your Favorite Settings • 5-Year Warranty and Free Software Upgrades
BrightEye Mitto 3G/Fiber/HD/SD Scan Converters Position
Output full screen SD or HD SDI video Even a small part of the computer screen, such as a YouTube video, is flawlessly upconverted to full screen HD SDI.
DVI
SDI Video HD, SD or 3Gb/s
Size Click and drag to move and resize selection
USB Audio DVI
Typical Mitto Connection
“Ensemble’s BrightEye gear met our requirements, including 12-bit accuracy, operation between minus 20º and plus 50º, and the ability to withstand constant vibration. BrightEye hardware has been running trouble-free for thousands of flight hours in New York and Los Angeles.” ~ Steve Cudnofskey, Systems Designer and Quality Control Manager, Geneva Aviation
5
BrightEye Mitto 3G/Fiber/HD/SD Scan Converters Exclusive Filtering and Scaling Technology
Used Worldwide
A superior quality scan converter, BrightEye Mitto has the advantage of proprietary scaling technology and exclusive multi-tap filtering. Even a small part of the computer screen, such as a YouTube video, will be upconverted to full screen HD. The region selected for output determines if Mitto acts as an upconverter or downconverter. The filters automatically adjust in accordance with the conversion being performed. The result is that the output looks as good, or better, than the original and passes the most stringent testing.
BrightEye’s compact size lets you put conversion right where it’s needed: in a ballroom, breakout room, backstage graphics workstation, playout workstation, a remote truck, at a live venue, or even on a helicopter. Reliable and easy to install, BrightEyes make your event look the best, even on jumbo screens, LED and monitor walls. And they’re affordable, too!
Digital and Analog Video and Audio The intuitive front panel interface makes it easy to choose the desired video output format. The genlock reference input allows the video outputs to be timed to house. The audio input accepts analog audio. AES is optional. Audio is embedded into the SDI outputs which is required for many high end applications. Audio delay controls let you adjust the audio with respect to video for perfect lip sync, which is crucial when using Skype video in a production environment.
Free Software Upgrades Forever Use BrightEye Mac or PC software to control a single BrightEye unit or any number of units connected to a USB hub. BrightEye Mac and PC software are included with each unit at no charge. BrightEye Mitto’s software is easily upgraded through the unit’s USB port. Software upgrades are available at no charge for the life of the product and are conveniently downloadable from the Ensemble Designs’ web site. Updates are free, forever. Every unit comes with a five-year warranty.
Six BrightEye Mitto Models to Choose From Select the perfect combination of features and price for your video facility BrightEye Mitto 3G BEM-1 DVI, VGA, or HDMI inputs HD or SD video outputs 3 Gb/s video output
Optical output Analog or embedded audio input AES audio input and output Full control of audio levels, channel mixing Adjustable audio delay RS-232/GPI control
6
BrightEye BrightEye Mitto 3G Fiber Mitto HD BEM-1F BEM-2
BrightEye BrightEye BrightEye Mitto HD Fiber Mitto Pro Fiber Mitto Pro 2 BEM-2F BEM-3F BEM-4
Scan Conversion for Presentations Ideal for PowerPoint and Keynote Presentations Made Beautiful Use BrightEye Mitto to show the full PowerPoint on the screen to the group and still keep the presenter's display on your computer for complete control. Use the BrightEye Mitto to select the PowerPoint window on your computer.
BrightEye Mitto converts the selected area on your computer to SD or HD SDI video for input to a monitor, projector, router or video production switcher.
Mitto Scan Converter SD or HD SDI to Switcher
VGA, DVI, or HDMI
Production Switcher or Router
SD or HD SDI to BrightEye 81 HDMI to Monitor
PowerPoint on PC or Mac with Mitto application
BrightEye 81
Flat Screen Display
Scan Conversion for iPhone and iPad Convert Video from Your Mobile Device into Digital Video High Quality Scaling BrightEye Mitto is a high performance scan converter that provides a new way to take just about any source to 3G, HD or SD SDI video. The BrightEye Mitto converts iPhone or computer material to SD and HD SDI video for input to a router or production switcher for use in video production applications.
Use a standard cable from Apple to connect the VGA or HDMI port on the iPhone or iPad to the Mitto’s DVI input. Mitto automatically scales the iPhone video to HD, SD or 3 Gb/s video. BrightEye Mitto has a reference input allowing the video output to be timed to house.
Mitto Scan Converter SD or HD SDI Video
Apple HDMI or VGA adapter cable
Program Out
iPhone or iPad Production Switcher HDMI to Projector BrightEye 81
7
Scan Conversion for Interviews Use Skype™, iChat™ and Facetime™ in Your Production or Live Show Skype Interviews Made Easy Use BrightEye Mitto with applications such as Skype, iChat and Facetime to bring interviews into your video production. You can have one or more video windows open on your computer. BrightEye Mitto converts the area you select to SD or HD SDI video for input into your video router or production switcher.
Memory Registers and GPI Use BrightEye Mitto’s memory registers to store and recall specific selections. For example, if you have four video interviews or windows up on your computer monitor, select window 1 and save that selection
to Mitto’s memory register 1; window 2 to memory register 2, and so on. And you can pre-set a selection that shows two video windows together, a twoshot. This is great for an interview segment. Memory registers can be recalled from the BrightEye Mac or PC software, or from an external GPI panel. You can even use this as a mini master control system and switch between eight different video sources from one computer. Mitto’s audio delay controls let you adjust the audio stream with respect to the video in order to get the lip-sync right.
Mitto Scan Converter VGA, DVI, or HDMI
Skype on PC or Mac with Mitto application
SD or HD SDI Video
Program Out
RS-232
GPI Control Panel
Production Switcher HDMI to Projector
BrightEye 81
8
Scan Conversion for Medical Applications Extremely Detailed Video Output for Operating Environments Exclusive Filtering and Scaling Technology The BrightEye Mitto is a high performance scan converter that takes a progressive computer output, either DVI or VGA, and converts it into high quality 3G, HD SDI, or SD SDI video. The high quality 1080p 3 Gb/s video output is perfect for distributing signals from medical devices such as MRI machines, endoscopes, and X-ray machines.
a medically approved power supply (ITE Standard). Ensemble Designs has these power supplies available. Be sure to specify this when placing an order with your BrightEye Mitto rep.
Nearly all medical devices have a 1080p digital output via DVI. Selecting a lesser resolution from the device in order to convert this signal to HD SDI results in the loss of subtle color differences and gray scale necessary to accurately evaluate the medical imagery. In addition, this imagery often has to travel great distances to classrooms and supporting hospitals for evaluation, making a fiber optic 3 Gb/s output a necessity. The BrightEye Mitto 3G Fiber, with its exclusive 3 Gb/s (1080p -1920x1200) HD SDI electrical and fiber optic output, is the perfect solution. Connect the 3G output from the medical device to the BrightEye Mitto via the DVI input port. Please note that Mitto is expecting a progressive format coming from a computer device. It will not work with an interlaced signal. Connect the loop through DVI output from the Mitto to the local monitor in the operating theater. If the Mitto is to be used inside an operating environment, it is a necessity that it be connected to
3 Gb/sec progressive DVI
Medically Approved Power Supply (ITE Standard)
From the Mitto front panel or in the Output Tab in the BrightEye Mac or BrightEye PC software, configure the HD Format to 1080p by clicking and holding the pull down bar. Select whether the standard is NTSC or PAL in the Standard pull down bar. In the Mode pull down bar, select 3G. If the surgeon or technician will be providing commentary during the procedure, a lapel mic may be connected directly into the audio input jack on the back of the unit. The audio will then be embedded into the SDI stream for distribution. The 3G SDI output of the Mitto is available electrically via the SDI output BNC. In addition, a fiber optic SDI output is available in the Mitto 3G Fiber. Many teaching hospitals will connect the electrical output to a control room for mixing with cameras and other graphical devices before distribution or for archival purposes. The fiber optic output is then routed to supporting hospitals or classrooms across campus, or crosscountry, maintaining the high quality necessary for proper evaluation and diagnosis.
SD or HD SDI to BrightEye 81 BrightEye 81
HDMI to Monitor
3G SDI Electrical 3G SDI Optical
MRI, endoscope or other medical device
Flat Screen Display
Control Room
Classroom Display Monitor Surgeon Mic Local Operating Theater Monitor Distant Hospital Display
Archive
9
Scan Conversion for Worship Song Lyrics and Skype from Your Computer to Your Congregation Songs and Hymns
Audio Delay for Lip Sync
You can easily select just a portion of the song or hymn lyrics for projection. No need to show the entire computer desktop, select just the section you want to project. BrightEye Mitto converts the selected area to SD or HD SDI video for input to a video router, projector or production switcher.
BrightEye Mitto’s audio delay lets you adjust the audio stream with respect to the video and get the lip-sync right, which is crucial for Skype applications.
Missionary Interviews via Skype Made Easy Use BrightEye Mitto to show an interview with a missionary or off-site guest. You can select just the Skype™ or YouTube™ video window and feed that to Mitto and then to a projector or video switcher.
A superior quality scan converter, BrightEye Mitto uses new, proprietary scaling technology and exclusive multi-tap filtering to ensure the video output looks superior. The filters automatically adjust in accordance with the conversion being performed.
Image Magnification System
Mitto Scan Converter VGA, DVI, or HDMI
SD or HD SDI Video
Program Out
PowerPoint or song library on PC or Mac with Mitto application Production Switcher
10
Scan Conversion for Teleprompting Cost Effective and Simple Effective Teleprompting Solution The BrightEye Mitto scan converter can be used with applications such as Microsoft Word or PowerPoint™ to provide an effective teleprompting solution without breaking the bank. Compose the script for teleprompting using word processing software such as Microsoft Word. For best results, use a bold, sans serif font of sufficient size to be easily read. Double spacing the document may help in making scrolling text easier to read. Using the selection tool in the BrightEye software, or the front panel controls on the Mitto itself, define a “slot” through which the text will scroll. This window should be roughly three or four lines of text tall to allow the talent to see more than the single line of text he is speaking.
Once the area is defined, Mitto will scale the text to fill the monitor, making the script easy to read. Displaying the script for prompting can be accomplished by either placing a flat screen display just under the camera lens facing the talent, or by placing a half silvered mirror in front of the camera lens. A monitor can then be set on the floor in such a way that it reflects on the mirror for the talent to read. To scroll the text as the talent is reading, simply use the scroll bars in the word processing software. The text will scroll through the window as the presenter reads.
Half Silver Mirror BITTERLY COLD TEMPERATURES ARE GRIPPING THE EASTERN PART OF THE COUNTRY ... FROM NEW ENGLAND TO FLORIDA.
Flatscreen Display
Mitto Scan Converter DVI
Word processor on PC or Mac with Mitto application
SDI Video HDMI
BrightEye 81
Flatscreen Display
11
BrightEye Mitto 3G/Fiber/HD/SD Scan Converters Sync Separator Reference Input Composite, TLS,10 MHz
ScH Phase 10M Input VITC Detect
Clock Generation
TCXO Internal Precision Standard
USB External Control
RS-232
Micro Processor & Control Systems
Timecode Generator
DVI-I Input Digital or Analog RGB
Black Gen
EDID Source
Composite Encoder & DAC
VITC Inserter
DDR2 Memory
Cpst/AES Output Composite NTSC/PAL or AES Audio
AES Encoder DVI/HDMI Receiver
Raster Scaling Pixel Filtering
VGA/RGB A to D
Progressive to Interlace Conversion
RGB to YCrCb Colorspace Conversion
Audio Embedder
Frame Synchronizer
DVITC ATC Inserter
HD/SD Serializer
Audio Delay
SRC
SDI Video Output 3G/HD/SD
DVI-I Loop Out
Audio In (mini-jack)
AES Rcvr
SRC
AES Rcvr
SRC
Audio Source Select
Gain & Mixing
Stereo ADC
Block diagram represents BEM-1. See specs for variations on other models.
Order Info BEM-1 BEM-1F BEM-2 BEM-2F BEM-3F BEM-4
BrightEye Mitto 3G BrightEye Mitto 3G Fiber BrightEye Mitto HD BrightEye Mitto HD Fiber BrightEye Mitto Pro Fiber BrightEye Mitto Pro 2
Each unit comes with 1 USB cable, 2 VGA to DVI adapters, 1 modular power supply and BrightEye Software for Mac and PC
Mitto Defined: • Comes from the Latin root for transmit or send • It’s also the root word of uncompromising 12
BrightEye Mitto 3G/Fiber/HD/SD Scan Converters Computer Input Number One Type DVI (Supports HDMI or VGA with adapter) Connector DVI-I Resolution Up to 1920 x 1200 Reference Input Number One, BNC Type 1 V P-P Composite Video PAL, NTSC, Tri-Level Sync Impedance 75 Ω Return Loss >40 dB Note: When no reference is provided, Mitto runs from an internal "sync gen grade" precision frequency reference. Analog Audio Inputs Number Connector Impedance Max Input Level Quantization Sample Rate Reference Level Frequency Response Crosstalk Dynamic Range
One stereo pair 1/8” mini jack >15K Ω 24 dBu 24 bits, 128 x oversampled 48 KHz -10 dBu or +4 dBu ±0.1 dB, 20 Hz to 20 KHz <106 dB >106 dB
AES/EBU Digital Inputs (BEM-1, 1F, 2, 2F) Number Two (four channels) Type AES3id, S/PDIF Connector 1/8” mini jack Bit Depth 20 and 24 Bit Sample Rate 30 KHz to 192 KHz (Sample Rate Converted Internally to 48 KHz) Serial Digital Output Number Two, BNC One for BEM-1F , 2F and 3F Signal Type 270 Mb/s SD SDI, SMPTE 259M 1.485 Gb/s HD SDI,SMPTE 274M, 292M, 296M 2.97 Gb/s HD SDI (BEM-1, BEM-1F only) SMPTE 424M, 425M Processing 16 bit processing 12 and 14 bit upconversion Delay Adjustable from 16 msec to 40 msec Note: Output is fully timeable with respect to the reference input. Audio Embedded Impedance 75 Ω Return Loss >15 dB to 1.485 GHz >10 dB to 2.97 GHz Output DC None (AC coupled)
All Mittos support: 1080i (SMPTE 274M -4,5,6) 50, 59.94 or 60 Hz 720p (SMPTE 296M -1,2,3) 50, 59.94 or 60 Hz 525i, 625i (SMPTE 259M) BEM-1, BEM-1F, BEM-2 and BEM-2F also support: 1080sF (RP211 -14,15,16) 23.98, 24, 25 Hz 1080p (SMPTE 274M -9,10,11) 23.98, 24, 25 Hz BEM-1 and BEM-1F also support: 1080p (SMPTE 424M, 425M), 50, 59.94, 60, Level A Optical Output (BEM-1F, 2F, 3F) Number One, LC/UPC Type Follows SDI configuration Wavelength 1310 nm (non-CWDM) Wavelengths 170 nm –1610 nm at 20 nm CWDM spacing available. Call factory for price and details. Power -7 dBm Max Cable Length 20 km (For greater distances, or higher power and larger loss budgets, please contact the factory) Fiber Type Single Mode Multi-mode compatible with attenuation at transmit end Analog Video Output Number Type Return Loss Output DC
One, BNC Composite PAL or NTSC (when SD is selected on the SDI output) >40 dB <100 mV
Computer Monitor Output Number One, looping Type DVI (Supports HDMI or VGA with adapter) Connector DVI-I Format Follows input Control (BEM-1, 1F, 2, 2F) Number One Connector 9 pin D Type RS-232, GPI General Specifications Size 5.625” W x 1.7” H x 5.5” D (143 mm x 20 mm x 140 mm) including connectors Weight 1 lb 6 oz Power 12 volts, 12 watts (100-230 VAC modular power supply) Temperature Range 0 to 40° C ambient (all specs met) Relative Humidity 0 to 95° non-condensing Altitude 0 to 10,000 ft. 13
BrightEye NXT 410 Clean HDMI Router Instantaneous HDMI Clean Switching The new BrightEye NXT 410 Clean HDMI Router cleanly and instantly switches your HDMI sources. The HDMI output switches instantaneously, never a glitch or pop. Feed the NXT 410 with cameras and other HDMI sources and take the output to projectors, flat screens and production equipment. The built-in frame synchronizer provides two clean switched outputs. The HDMI output always clean switches and you can assign the NXT’s second clean switch to one of the SDI or SFP outputs. Great for fly packs, video conference rooms and anywhere you need a small router, this new BrightEye has incredible power in a small 1RU high by 1/3 RU wide footprint – about the size of a CD box set. The exclusive front panel LCD displays realtime full motion video of your HDMI and SDI router sources.
Integrate HDMI and SDI I/O With both HDMI and SDI inputs and outputs, the NXT 410 makes it easy to integrate and switch signals from all types of equipment, regardless of the video format. Cameras with HDMI outputs can be used directly alongside SDI sources, and seamlessly routed to either HDMI or SDI outputs. The SFP (small format pluggable) cage can be populated with dual SFPs that have fiber optic or other connectors, allowing you to determine the best connector for your installation. Adding SFPs gives you true flexibility in combining electrical BNC, HDMI and fiber optic inputs and outputs.
Features • Clean Switching and Routing of HDMI and SDI Sources • Use with HDMI Cameras and Devices • Supports HD 1.5 Gb/s and 3 Gb/s, and SD 270 Mb/s SDI signals • Built-in Frame Sync Provides Two Clean Switched Outputs • Genlockable and Timeable • Front Panel and Web-Based Control • LCD Display with Realtime Full Motion Video • Passes Embedded Audio • Compact and Rugged • 5-Year Warranty and Free Software Upgrades
Assignable I/O and Flexible Architecture:
4 HDMI inputs 1 HDMI output 2 dedicated SDI inputs 2 dedicated SDI outputs 1 SDI port that can be configured as an input or output 1 SFP cage that can take a single or dual fiber optic SFP 1 reference input 14
BrightEye NXT 415 and 430 Compact Routers New Routing Technology Introducing the BrightEye NXT 430 Clean Router for clean, quiet switching of video and audio sources. The exclusive front panel LCD displays realtime full motion video of your router sources. Great for fly packs, ENG and anywhere you need a small router, this new BrightEye has incredible power in a small 1RU high by 1/3 RU wide footprint – about the size of a CD box set.
Clean Switch - Use Asynchronous Sources The BrightEye NXT 430 Router gives you two clean switched outputs. The router’s built-in clean switch provides full frame synchronization which means you can switch cleanly between asynchronous sources. Wild feeds from cameras, helicopters, and microwaves can be fed to the BrightEye Router for perfect switching. If you don’t need clean switching, you may prefer the BrightEye NXT 415 Compact Router. The NXT 415 has all the capability of the 430, except for clean switched outputs.
Assignable I/O and Flexible Architecture You get to configure the number of inputs and outputs; the configuration is changeable on the fly. There are 2 fixed input BNCs, 2 fixed output BNCs and 7 assignable BNCs that you configure either as inputs or outputs. The two SFP (small format pluggable) cages can be populated with dual SFPs that have fiber optic or other connectors, allowing you to determine the best connector for your installation. Adding SFPs gives you true flexibility in combining electrical BNC and fiber optic inputs and outputs.
Features • Routing for 3G, HD and SD Video • Clean Switching of Video and Embedded Audio • Flexible I/O. You configure BNCs and SFPs as Inputs or Outputs: 13x2, 2x13 and Anything In Between • Front Panel and Web-Based Control • LCD Display with Realtime Full Motion Video • Compact and Rugged • Genlockable and Timeable • Passes Embedded Audio • 5-Year Warranty and Free Software Upgrades
Two great choices: BrightEye NXT 430 Clean Compact Router BrightEye NXT 415 Compact Router
15
BrightEye 5 Analog Composite TBC and Frame Sync BrightEye 5 is a Time Base Corrector with analog composite inputs and outputs. 12 bit digital signal processing ensures the best signal handling and a solid output. BrightEye 5 will time base correct signals from analog sources such as consumer VCRs, cameras and noisy receivers. The analog input is converted at 12 bits of resolution for digital processing. The signal is time base corrected and frame synchronized to the reference input and converted back to analog for output. BrightEye 5 auto detects the video standard of the input (PAL or NTSC). Basic controls are provided on the front panel. With BrightEye Mac or PC software, you can control video proc functions; Gain, Chroma, Pedestal, and Hue. The vertical interval can be passed or blanked.
16
Features • Use with VCRs, Cameras, Satellite Receivers • Analog Video Inputs and Outputs • TBC and Frame Sync • Format Mode lock for use with noisy/intermittent input signals • 12 Bit Processing
BrightEye 5 Analog Composite TBC and Frame Sync Analog Video Input Number Type Impedance Return Loss Input DC Input Hum
Analog Video Output One NTSC, PAL Composite 75 Ω >40 dB, DC to 5.5 MHz +/-1 volt DC <100 mV
Number Type Delay Return Loss Output DC
General Specifications
Reference Input Number Type Impedance Return Loss
One 1 V P-P Composite Video, PAL or NTSC 75 Ω >40 dB
Performance Frequency Response K Factor ScH Phase Error Differential Phase Differential Gain Signal to Noise Timing Window Timing Resolution
Two Composite PAL or NTSC (follows input) Adjustable from < 90 µSec to 1 frame >40 dB <100 mV
±0.1 dB , 0 to 5.5 MHz <1% <±2° <1° <1% >65 dB Infinite (with respect to reference) Output ScH Phase matches reference Adjustable to within 1° of subcarrier
Size Weight Power Temperature Range Relative Humidity Altitude
5.625” W x 0.8” H x 5.5” D (143 mm x 20 mm x 140 mm) including connectors 14 oz 12 volts, 4 watts (100-230 VAC modular power supply) 0 to 40° C ambient (all specs met) 0 to 95° non-condensing 0 to 10,000 ft.
Composite Out 1 Cpst In
12 bit A to D Converter
TBC/ Frame Sync
Proc Amp
12 bit D to A Converter
Composite Out 2
Ref In
17
BrightEye 25 Analog Video/Audio to SD SDI Converter with TBC and Embedder BrightEye 25 converts analog composite video to SD SDI, with simultaneous conversion of four channels of audio and embedding. A TBC/Frame Sync is a standard feature and allows this BrightEye to work with any sort of video input. Great for video production and desktop applications, BrightEye 25 can be used with sources such as VTR/VCRs and incoming satellite feeds. The analog input is converted at 12 bits of resolution and digitally decoded to 10 bit YCrCb components. The signal is then time base corrected and frame synchronized to the reference input. The audio is converted to digital and then it passes through the builtin four channel mixer with shuffle and level control. The video and audio signals join up in an embedder which can be targeted to any of the four groups. Basic controls are accessed on the front panel. BrightEye Mac or PC software provides access to video proc functions and the built-in audio mixer. The vertical interval can be passed or blanked. VU indication is provided on the front panel and through BrightEye Mac or PC software.
18
Features • Convert Analog Sources to Embedded SDI • Analog Audio and Video Inputs • Embedded SDI Output • TBC and Frame Sync • 12 and 24 Bit Processing
BrightEye 25 Analog Video/Audio to SD SDI Converter with TBC and Embedder Analog Video Input Number Type Impedance Return Loss Input Input Hum
Analog Video to SDI Performance One NTSC, PAL Composite 75 Ω >40 dB, DC to 5.5MHz DC +/-1 volt DC <100 mV
Bit Resolution Decoding Signal to Noise Frequency Response Analog Audio Inputs
Reference Input Number Type Impedance Return Loss
One 1 V P-P Composite Video, PAL or NTSC 75 Ω >40 dB
Serial Digital Output Number Type Delay Impedance Return Loss Output
Cpst In
12 bit input quantization, 4 x oversampling Adaptive Comb Filter, 3 or 5 line selectable >62 dB, weighted ±0.1 dB, 0 to 5.5 MHz
Two 270 Mb/s SD Serial Digital SMPTE 259M Adjustable from < 90 µSec to 1 frame 75 Ω >15 dB DC None (AC coupled)
Number Four Type Balanced Impedance >15K Ω Maximum Input Level 24 dBu CMRR >60 dB, 20 Hz to 10 KHz Quantization 24 bits, 128 x oversampled Sample Rate 48 KHz Reference Level -10 dBu or +4 dBu Frequency Response ±0.1 dB, 20 Hz to 20 KHz Crosstalk <106 dB Dynamic Range >106 dB General Specifications Size Weight Power Temperature Range Relative Humidity Altitude
5.625” W x 0.8” H x 5.5” D (143 mm x 20 mm x 140 mm) including connectors 1 lb 12 volts, 5 watts (100-230 VAC modular power supply) 0 to 40° C ambient (all specs met) 0 to 95%, non-condensing 0 to 10,000 ft.
SD SDI Out
12 bit A to D Converter and Decoder
TBC/ Frame Sync
Proc Amp
Embedder
Serializer
Reference In
Analog Audio In
4 Channel A to D
4 Channel Mixer/Shuffler
19
BrightEye 46 3G/HD/SD/ASI Electrical to Optical Converter BrightEye 46 is an electrical to optical converter and distribution amplifier that can be used with 3 Gb/s and 1.5 Gb/s high definition signals, standard definition video signals, or ASI signals. Perfect for long projector runs, or connections to other buildings, The BrightEye 46 makes converting to the optical domain a snap. The video input is reclocked and presented on four BNCs and is also converted to an optical signal and presented on an optical LC connector. This optical output can drive single mode fiber to a distance of 20 kilometers. With an optical launch power attenuator, multi-mode fiber can also be used with BrightEyes. This is a simple device with no USB port and no interface to BrightEye Mac or PC software. Front panel indicators show the presence of an input signal and power.
20
Features • Optical Transmitter • Electrical to Optical Converter • Use with HD or SD signals • Use with ASI Signals • 3G HD, Level A and Level B Supported • Serves as a Distribution Amplifier • Passes Embedded Audio
BrightEye 46 3G/HD/SD/ASI Electrical to Optical Converter Serial Digital Input
Optical Output
Number One Signal Type 270 Mb/s SD Serial Digital (SMPTE 259M) 1.485 Gb/s HD Serial Digital (SMPTE 274M, 292M or 296M) 2.97 Gb/s HD Serial Digital (SMPTE 424M, 425M) Level A, Level B Impedance 75 Ω Return Loss >15 dB to 1.485 GHz >10 dB to 2.97 GHz Max Cable Length 300 meters for 270 Mb/s 100 meters for 1.485 Gb/s 70 meters for 2.97 Gb/s (Belden 1694A) Automatic Input Cable Equalization
Number One Type SD and ASI (SMPTE 297M, optical equivalent of 259M) 1.485 Gb/s HD (SMPTE 274M, 292M or 296M) 2.97 Gb/s HD (SMPTE 424M, 425M) Wavelength 1310 nm (non-CWDM) Wavelengths 170 nm – 1610 nm at 20 nm CWDM spacing available. Call factory for price and specify part number BE46-SP. Weight 1 lb 2.3oz Power -7 dBm Max Cable Length 20 km (For greater distances, or higher power and larger loss budgets, please contact the factory) Fiber Type Single Mode Multi-mode compatible with attenuation at transmit end Connector LC/UPC
Serial Digital Output Number Signal Type Impedance Return Loss Output DC
Four 3G/HD/SD/ASI Serial Digital , follows input 75 Ω >15 dB to 1.485 GHz >10 dB to 2.97 GHz None (AC coupled)
General Specifications Size Weight Power Temperature Range Relative Humidity Altitude Laser Diode
5.625” W x 0.8” H x 5.5” D (143 mm x 20 mm x 140 mm) including connectors 15 oz 12 volts, 7 watts (100-230 VAC modular power supply) 0 to 40° C ambient (all specs met) 0 to 95° non-condensing 0 to 10,000 ft. Optical Out
3G/HD/SD/ASI In Reclocker
3G/HD/SD/ASI Out (follows input)
21
BrightEye 72 & 72-F 3G/HD/SD SDI Electrical or Optical to HDMI Converter High-End Display Applications Pay a tenth of the cost for your monitors. Combine BrightEye 72 with any HDMI monitor for high-end display applications in live event and post. BrightEye 72 accepts an SD, 1.5 Gb/s HD or 3 Gb/s HD SDI digital signal and outputs HDMI. Plus it displays open captions, timecode and audio presence. Front panel controls include: complete proc amp, built-in test signals for use in aligning the monitor, graticule, H/V pulse delay, on screen audio VU meters, timecode burn in, AFD indicator and open caption decoding. BrightEye 72 can display open captions on any HDMI video monitor. 608 or 708 caption data is decoded and displayed on-screen. Horizontal and vertical split modes provide an easy way to see data in the vertical and horizontal intervals, including audio and closed caption data blocks. A special Mirror Flip Output mode can be enabled, causing the output image to be flipped left to right for use with on-stage talent. Open captions are displayed correctly when Mirror mode is selected. Use BrightEye 72 in applications where you need to adjust the color temperature of on-set monitors so they look right on-camera. For set-ups using 3G, the issue of monitoring the signal becomes a challenge. The BrightEye 72 provides a convenient way to monitor any type of digital video signal. Order the BrightEye 72-F if you need an optical input.
22
SDI Embedded Audio, HDMI and Surround Sound Audio presence is reported and on-screen VU meters show all 16 audio channels. If audio or Dolby E are embedded on the SDI input, audio is passed through on the HDMI output. The HDMI spec supports 8 channels of audio. The BrightEye 72 monitors 16 channels of SDI embedded audio, but outputs 8 channels per the HDMI specification. The first 8 channels of the SDI audio stream are output to HDMI. You can connect the HDMI output to a surround sound speaker system by maintaining a specific channel order. This ensures that the correct audio signals are sent to the proper speakers.
Output Mapping of HDMI Audio The output mapping of the BrightEye 72 HDMI audio is as follows: CH 1 Front Left CH 2 Front Right CH 3 Low Frequency Effects CH 4 Front Center CH 5 Left Rear CH 6 Right Rear For those using 7.1 surround: CH 7 Left Rear Center (or Left Front Center) CH 8 Right Rear Center (or Right Front Center)
Features • Turn Any Monitor into a High-End Q/C Monitor
• Timecode Burn In
• Use with HD or SD Monitors, VTRs and Projectors
• On-screen Controls
• HDMI Output – Monitor Any Digital Feed, Even 3G
• Audio Level Meters for 16 Channel Monitoring
• Use with HD or SD SDI Signals
• H & V Shift for Easier Trouble Shooting
• 3G HD, Level A Supported
• Graticule Overlay
• Caption Decoding - Open Caption Display for 608 and 708 Closed Caption Data
• Mirror Output Mode for On-Stage Talent
• Color Corrector – Adjust On-Set Monitors • AFD Indicator
• Analog Audio Outputs • Use in Post with 4:4:4 Material • Optical input available on BrightEye 72-F
23
Camera Color Correction Using the BrightEye 72 for Adjusting the Color Temperature of a Monitor The Need for Color Correction
Example of Adjustment Process
When working in an environment that has poor lighting or a mix of color temperatures, the camera may need color correction. The camera may also need contrast and brightness adjustments that cannot be made through the camera controls or codec. Similarly, putting a television monitor on set where it will appear in the scene on camera presents a difficult challenge. It is easy to make the monitor too bright.
Take the HD SDI signal from the camera and send it to the BrightEye 72. Then take the HDMI output from the BrightEye 72 and send it back to the codec.
After the scene is lit and the camera is white balanced to the studio lighting, the on-camera talent will look correct. But unless the color temperature of the monitor matches the studio lighting, the color in the images on the monitor will be incorrect when in the camera shot. The face of the monitor is an actual source of light, while everything else in the set is reflecting light from the lighting instruments. If you hold a white card in front of the monitor next to the 100% white flag in color bars, you can adjust the monitor until they match.
Chroma, Hue, Brightness, Contrast Using the BrightEye 72's Color Corrector, you can color balance any HDMI monitor without ever touching a single control on the monitor itself. You can make both gross and fine adjustments to chroma, hue, brightness, contrast and other settings, such as mirror and test patterns. The BrightEye 72 has a Processing Amp that allows for substantial adjustment to the camera images. Note that the controls are all accessible through the front panel of the BrightEye 72 using the On Screen Display. Or you can use BrightEye Mac or PC software to connect to the BrightEye 72's USB port.
24
Select the 20/80 Test Pattern from the BrightEye 72's test signal generator. The 20% Gray and Black regions will be used to set black balance. The 80% Gray (nearly white) is used to adjust the gain of each of the Red, Green, and Blue channels. With the camera, compose a shot of the monitor with the 20% region filling the screen. There are full screen 20% and 80% patterns as well if you are working with small monitors. Viewing the camera output on a vectorscope, adjust the RGB offsets to collapse the chroma to a single dot. This is best done using just Red and Blue, leaving Green as the reference. Next, frame the shot on the 80% segment. Repeat the adjustment procedure to collapse the chroma, this time using the RGB Gain controls. Select the 10 step grayscale chipchart or SMPTE Bars on BrightEye 72's internal test signal generator. While viewing the monitor through the camera, use BrightEye 72's Proc Amp controls (Brightness, Contrast, Chroma) to achieve proper exposure.
BrightEye 72 & 72-F 3G/HD/SD SDI Electrical or Optical to HDMI Converter Serial Digital Input for BrightEye 72
SDI Standards Supported
Number One Type 1.485 Gb/s HD Serial Digital (SMPTE 274M, 292M or 296M) 2.97 Gb/s HD Serial Digital (SMPTE 424M, 425M), Level A SD Serial Digital (270 Mb/s SMPTE 259M) Impedance 75 Ω Return Loss >15 dB to 2.97 GHz Max Cable Length 300 meters for 270 Mb/s 100 meters for 1.485 Gb/s 70 meters for 2.97 Gb/s (Belden 1694A) Automatic Input Cable Equalization
1080i (SMPTE 274M -4,5,6) 50, 59.94 or 60 Hz 720p (SMPTE 296M -1,2,3) 50, 59.94 or 60 Hz 1080p (SMPTE 274M -9,10,11) 23.98, 24, 25 Hz 1080sF (RP211 -14,15,16) 23.98, 24, 25 Hz 1080p (SMPTE 424M, 425M), 50, 59.94, 60, Level A 525i, 625i (SMPTE 259M)
Optical Input for BrightEye 72-F Number One Connector LC/UPC Type 270 Mb/s (SMPTE 297M, optical equivalent of 259M) 1.485 Gb/s Gb/s HD Serial Digital (SMPTE 274M, 272M or 296M) 2.97 Gb/s HD Serial Digital (SMPTE 424M, 425M) Wavelength 830 to 1610 nm Receiver Sensitivity -18 dBm Max Cable Length 20 km (For greater distances, or higher power and larger loss budgets, please contact the factory) Fiber Type Single Mode Multi-mode compatible with attenuation at transmit end
HDMI Output Number One Type HDMI 1.3 Format Follows input Serial Digital Output Number Type Delay Impedance Return Loss Max Cable Length
One, loopback Follows input < 5 µSec 75 Ω >15 dB to 2.97 GHz 300 meters for 270 Mb/s 100 meters for 1.485 Gb/s 70 meters for 2.97 Gb/s (Belden 1694A)
Analog Audio Output Number
8 channels
General Specifications Size Weight Power Temperature Range Relative Humidity Altitude
5.625” W x 0.8” H x 5.5” D (143 mm x 20 mm x 140 mm) including connectors 14 oz 12 volts, 7 watts (100-230 VAC modular power supply) 0 to 40° C ambient (all specs met) 0 to 95%, non-condensing 0 to 10,000 ft.
25
BrightEye 72 & 72-F 3G/HD/SD SDI Electrical or Optical to HDMI Converter
BrightEye 72 3G/HD/SD SDI Electrical to HDMI Converter Graticule Gen Input Status Display Test Signal Gen
On Screen Controls
3G/HD/SD SDI In
3G/HD/SD SDI Loopback
Video Proc & Color Corrector
Overlay Combiner
H&V Delay
Caption Reader
Open Caption Decoding
Timecode Reader
Timecode Window Gen
Audio Meter Overlay
16 Chan Audio Demux
26
HDMI Out
Analog Audio Out Audio Out Selection
BrightEye 72 & 72-F 3G/HD/SD SDI Electrical or Optical to HDMI Converter
BrightEye 72-F 3G/HD/SD SDI Optical to HDMI Converter Graticule Gen Input Status Display Test Signal Gen
On Screen Controls
Optical In
3G/HD/SD SDI Loopback
Video Proc & Color Corrector
Overlay Combiner
H&V Delay
Caption Reader
Open Caption Decoding
Timecode Reader
Timecode Window Gen
Audio Meter Overlay
16 Chan Audio Demux
HDMI Out
Analog Audio Out Audio Out Selection
27
BrightEye 75 HD/SD Analog to Digital Video Converter BrightEye 75 is an analog video to digital converter and audio embedder. Standard definition component or composite, or high definition analog component video is accepted on the input BNCs. Two channels of analog audio are input on a plugable Phoenix connector.
Features
This unit is perfect for use with HD cameras or other devices with analog I/O. The digital output will carry the full, un-compressed input, synchronous to a genlock reference. You can turn a hand-held HD camera into a digital source. A three camera, live studio suddenly becomes affordable.
• Serial Digital HD or SD Embedded Output
• Use with Analog HD Cameras and Set Top Boxes • Turn Analog Cameras Into Digital HD Sources • HD/SD Analog Inputs • Analog Audio Inputs • TBC and Frame Sync
The built-in TBC/Frame Synchronizer allows you to feed asynchronous or noisy signals to the BrightEye 75. The input is digitized to 12 bits of resolution and time base corrected by a noise tolerant tracking circuit. An external reference input allows genlock to a house reference. Input selection, gain control, and TBC enable is provided through the front panel interface. Video levels can be adjusted through BrightEye Mac or PC software. The video and audio signals are embedded and presented on a BNC. The output follows the SD or HD input standard.
Analog HD or SD Pr, R In
14 bit A to D Converter and Decoder
C, Pb, B In
TBC/ Frame Sync
HD or SD SDI Out (Follows Input) Proc Amp
Cpst, Y, G In
Reference In 2 Channel A to D 2 Channel Analog Audio In
28
Mixer/Shuffler
Embedder
Serializer
BrightEye 75 HD/SD Analog to Digital Video Converter Analog Video Input Number Type Resolution Impedance Return Loss Input DC Input Hum
Analog Video to SDI Performance One HD or SD: Y, Pr, Pb (SMPTE or Beta levels) HD or SD: Analog Component RGB (sync on green) Analog Composite PAL or NTSC Analog S-Video PAL or NTSC Digitized at 12 bits 75 Ω >40 dB +/-1 volt DC <100 mV
Analog Audio Inputs Number Two Type Balanced Impedance >15K Ω Max Input Level 24 dBu CMRR >60 dB, 20 Hz to 10 KHz Quantization 24 bits, 128 x oversampled Sample Rate 48 KHz Reference Level -10 dBu or +4 dBu Frequency Response ±0.1 dB, 20 Hz to 20 KHz Crosstalk <106 dB Dynamic Range >106 dB Serial Digital Output Number Type Impedance Return Loss Max Cable Length
One Follows input standard HD Serial Digital 1.485 Gb/s SMPTE 274M, 292M or 296M or SD Serial Digital 270 Mb/s SMPTE 259M 75 Ω >15 dB 100 meters for HD 300 meters for SD (Belden 1694A)
Bit Resolution Decoding K Factors Signal to Noise Freq Response
14-bit input quantization 4x oversampling Fully adaptive comb filter > 1% > 64 dB weighted ± 0.1 dB, 0 to 5.5 MHz in SD ± 0.1 dB, 0 to 12 MHz; ± 0.5 dB, 12 to 30 MHz in HD
HD Standards Supported 1080i (SMPTE 274M -4,5,6) 50, 59.94 or 60 Hz 720p (SMPTE 296M -1,2,3) 50, 59.94 or 60 Hz 1080p (SMPTE 274M -9,10,11) 23.98, 24, 25 Hz 1080sF (RP211 -14,15,16) 23.98, 24, 25 Hz Embedded Output (In Serial Output) Group Assign Channels Bit Depth
One of four groups Two 24 Bit
Reference Input Number Type Impedance Return Loss
One 1 V P-P Composite Video, PAL or NTSC or Tri-Level Sync 75 Ω >40 dB
General Specifications Size Weight Power Temperature Range Relative Humidity Altitude
5.625” W x 0.8” H x 5.5” D (143 mm x 20 mm x 140 mm) including connectors 15 oz 12 volts, 6 watts (100-230 VAC modular power supply) 0 to 40° C ambient (all specs met) 0 to 95%, non-condensing 0 to 10,000 ft.
29
BrightEye 81 3G/HD/SD SDI to HDMI Converter Convert HD or SD SDI video feeds to HDMI with the BrightEye 81. Convenient for feeding a video monitor, projector or LED/monitor wall, BrightEye 81 provides a reliable way move video into the HDMI domain.
Features
BrightEye 81 supports standard definition video signals, 3 Gb/s and 1.5 Gb/s high definition signals. The HDMI output is not HDCP encrypted.
• Dual Link to HDMI Converter
BrightEye 81 also functions as a Dual Link to HDMI and 3G SDI converter. When the input is Dual Link 4:4:4, the BrightEye 81 provides two identical SDI outputs that are the 3G Level B version of the input video, and the HDMI output is HD 4:4:4. Signal monitoring and control is provided through the included BrightEye Mac and PC software.
30
• 3G, HD and SD SDI to HDMI Converter • Use with Video Monitors or Projectors That Have HDMI Input • Dual Link to 3G SDI Converter • Use with HD or SD Signals • Passes Embedded Audio
BrightEye 81 3G/HD/SD SDI to HDMI Converter Serial Digital Input
HDMI Output
Number One SDI, BNC or Two for Dual Link, BNC Signal Type 270 Mb/s SD Serial Digital (SMPTE 259M) 1.485 Gb/s HD Serial Digital (SMPTE 274M, 292M or 296M) Dual Link HD SDI (SMPTE 372M) 2.97 Gb/s HD Serial Digital (SMPTE 424M, 425M) Level A Impedance 75 Ω Return Loss >15 dB to 1.485 GHz >10 dB to 2.97 GHz Max Cable Length 300 meters for 270 Mb/s 100 meters for 1.485 Gb/s 70 meters for 2.97 Gb/s (Belden 1694A) Automatic Input Cable Equalization
Number One Type HDMI 1.3 Format HDMI 1.3
SDI Standards Supported 1080i (SMPTE 274M -4,5,6) 50, 59.94 or 60 Hz 720p (SMPTE 296M -1,2,3) 50, 59.94 or 60 Hz 1080p (SMPTE 274M -9,10,11) 23.98, 24, 25 Hz 1080sF (RP211 -14,15,16) 23.98, 24, 25 Hz 1080p (SMPTE 424M, 425M), 50, 59.94, 60, Level A Dual Link HD SDI 1080 RGB 4:4:4 (SMPTE 372M) 525i, 625i (SMPTE 259M)
Serial Digital Output Number Signal Type Impedance Return Loss Output DC
Two, BNC Follows input When input is Dual Link HD SDI, the SDI outputs are identical 3G Level B SDI signals (SMPTE 425M) 75 Ω >15 dB to 1.485 GHz >10 dB to 2.97 GHz None (AC coupled)
General Specifications Size Power Temperature Range Relative Humidity Altitude
5.625” W x 0.8” H x 5.5” D (143 mm x 20 mm x 140 mm) including connectors 12 volts, 7 watts (100-230 VAC modular power supply) 0 to 40° C ambient (all specs met) 0 to 95° non-condensing 0 to 10,000 ft.
HDMI Out Video and Audio
3G/HD/SD SDI In or HD Dual Link A In
HDMI Transmitter
Deserializer Autotimer
Out 1
Dual Link Encoder Audio Encoder
Deserializer
3G/HD/SD SDI or Dual Link 3G (Level B)
Serializer
HD Dual Link B In 8 Channel Audio Demux
Out 2 Audio Signal to HDMI
31
BrightEye 83 HDMI to 3G/HD/SD SDI Converter Convert HDMI to HD or SD SDI with the BrightEye 83. Convenient for video cameras, playout devices and other sources with an HDMI output, BrightEye 83 presents the serial digital video signal on two BNC outputs.
Features
BrightEye 83 is an HDMI converter for use with standard definition video signals and 3 Gb/s and 1.5 Gb/s high definition signals.
• Passes Embedded Audio
• HDMI to HD and SD SDI Converter • Use with Cameras and Other Sources that have an HDMI Output
Signal monitoring and control is provided through the included BrightEye Mac and BrightEye PC software. In compliance with the licensing restrictions on HDCP encrypted material, BrightEye 83 cannot convert encrypted signals to SDI form.
Format Detection
HDMI In
HDMI Receiver & Color Space Conversion
Video Signal
TRS Insertion
Embedder
Audio Signal
Sample Rate Conversion
8 Channel Audio Processor
Clock Regenerator
32
to LED’s and BrightEye Mac/PC Application Software
to all circuits
Serializer
3G/HD/SD SDI Out
3G/HD/SD SDI Out
3G/HD/SD SDI Optical Out (BE83-F Only)
BrightEye 83-F HDMI to Optical and Electrical 3G/HD/SD SDI Converter Convert HDMI to HD or SD SDI with the BrightEye 83-F. Convenient for broadcast video cameras and other sources with an HDMI output. BrightEye 83-F presents both electrical and optical serial digital outputs. The optical output can drive single mode fiber to a distance of 20 kilometers. With an optical launch power attenuator, multi-mode fiber can also be used.
Features • HDMI to Optical and Electrical Converter • Use with Cameras and Other Sources that have an HDMI Output • Passes Embedded Audio
BrightEye 83-F is for use with standard definition video signals and 3 Gb/s and 1.5 Gb/s high definition signals. Signal monitoring and control is provided through the included BrightEye Mac and BrightEye PC software. In compliance with the licensing restrictions on HDCP encrypted material, BrightEye 83-F cannot convert encrypted signals to SDI form.
33
BrightEye 90 HD Up/Down/Cross Converter and ARC with AES Audio Easy To Use
Cross Conversion
BrightEye 90 is a versatile up/down/cross converter or aspect ratio converter for use with analog and digital video signals. The Swiss Army Knife of video conversion, the BrightEye 90 is a realtime processor that changes video formats without rendering. Simply set the BrightEye 90 to output your preferred HD or SD standard. The BrightEye 90 will accommodate whatever input you connect - analog composite, SD SDI or HD SDI. After setting the output standard, BrightEye 90 automatically converts the selected input to the correct standard for your event. The HDMI, SDI and composite outputs are all extremely high quality, suitable for any part of your signal chain. BrightEye 90 will upconvert, downconvert, cross convert, or act as an ARC, as needed. A special Mirror Flip Output mode can be enabled, causing the output image to be flipped left to right for use with on-stage talent. The built-in Frame Synchronizer allows you to feed asynchronous signals to the BrightEye 90. An external reference input allows genlock to a house reference. All vertical interval data and closed captioning is faithfully passed.
It’s easy to convert between various HD standards, whether 720p or 1080i. Simply select the output standard you need and connect the input – that’s all there is to it. Using the Manual Scaling controls allows video sizing necessary for picture-in-picture insertion or web distribution.
Upconverting to High Definition Feed the analog composite or SD SDI output of a camera or playout device to a BrightEye 90 and upconvert to HD. You can take the HDMI and HD SDI signals from the BrightEye 90 into your switcher or projection system. Upconverting existing SD equipment lets you leverage the equipment you already have and operate in the HD domain. While some cameras may have firewire out, using the video output and upconverting before distribution is preferable since longer cable runs can be achieved and quality is superior. Additionally, the BrightEye 90’s reference input allows you to time the upconverted video output for use with a production switcher.
Downconverting to Standard Definition BrightEye 90 will downconvert any type of HD signal and provides SD SDI, HDMI and an analog composite output, all suitable for broadcast or monitoring.
34
Aspect Ratio Conversion For converting between SD 4:3 and HD 16:9, BrightEye 90 has you covered. Just select the output standard you need and connect the input.
Audio Processing Made Simple BrightEye 90 handles both embedded audio and discrete AES digital audio streams. Sixteen channels of embedded audio are supported in BrightEye 90. If the incoming video has embedded audio, the audio will be safely bypassed around the video processing and lipsync will be preserved. Audio mixing is available for two of the four embedded groups of audio. The AES I/O ports can be configured for eight channels of incoming audio or for eight channels of audio output. The audio mixer can be used for AES channels as well. Mixer controls are accessed through BrightEye Mac or PC software.
Easy Audio Monitoring Audio monitoring is easy with BrightEye 90’s convenient 3.5 mm mini jack. Select the audio channels you want to monitor from the front panel and plug in a headset.
Front Panel and Software Control Input selection, gain control, and test pattern controls are provided through the front panel interface. Audio presence LEDs indicate which channels are detected. Controls for crop, letterbox and pillarbox are accessed from the front panel or BrightEye Mac or PC software. Video and audio levels and the audio mixer can be adjusted through BrightEye Mac or PC software.
BrightEye 90 HD Up/Down/Cross Converter and ARC with AES Audio
Features • Use with Cameras and Projection Systems • Turn Analog Camera into HDMI or SDI Source • High Quality HDMI Output • HD and SD Digital and Analog Composite Video I/O • AES Digital Audio I/O • Analog Audio Monitor Output • Mirror Output Mode for On-Stage Talent • Graticule and Safe Title Generator • Frame Sync • 12 and 16 Bit Processing • Passes Embedded Audio
35
BrightEye 90 HD Up/Down/Cross Converter and ARC with AES Audio Analog Video Input Number Type Resolution Impedance Return Loss Input DC Input Hum
HD Standards Supported One Analog Composite PAL or NTSC Digitized at 12 bits 75 Ω >40 dB +/-1 volt DC <100 mV
Serial Digital Input Number One Signal Type 270 Mb/s SD Serial Digital (SMPTE 259M or 1.485 Gb/s HD Serial Digital (SMPTE 274M or 296M) Impedance 75 Ω Return Loss >15 dB Max Cable Length 300 meters for 270 Mb/s 100 meters for 1.485 Gb/s Automatic Input Cable Equalization Reference Input Number Type Impedance Return Loss
One 1 V P-P Composite Video, PAL or NTSC or Tri-Level Sync 75 Ω >40 dB
Analog Video Output Number Type Return Loss Output
One Composite PAL or NTSC >40 dB DC <100 mV
Serial Digital Output Number Type Delay Processing Impedance Return Loss Max Cable Length
36
Two HD Serial Digital 1.485 Gb/s SMPTE 274M, 292M or 296M or SD Serial Digital 270 Mb/s SMPTE 259M Adjustable from 1 field to 1 frame 12 and 16 bit 75 Ω >15 dB 100 meters for HD 300 meters for SD (Belden 1694A)
1080i (SMPTE 274M -4,5,6) 50, 59.94 or 60 Hz 720p (SMPTE 296M -1,2,3) 50, 59.94 or 60 Hz 1080p (SMPTE 274M -9,10,11) 23.98, 24, 25 Hz 1080sF (RP211 -14,15,16) 23.98, 24, 25 Hz AES/EBU Digital Inputs Number Four (total of eight channels) (selectable as inputs or outputs) Type AES3id Connector Coaxial, 75 Ω Bit Depth 20 and 24 Bit Sample Rate 30 KHz to 96 KHz (Sample Rate Converted internally to 48 KHz) Reference Level -18 or -20 dBFS (selectable) AES/EBU Digital Outputs Number Four (total of eight channels) (selectable as inputs or outputs) Type AES3id Connector Coaxial, 75 Ω Bit Depth 24 Bit Sample Rate 48 KHz, synchronous to video output Reference Level -18 or -20 dBFS (selectable) Embedded Output (In Serial Output) Group Assign Channels Bit Depth
Two of four groups Sixteen passed 24 Bit
HDMI Output Number One Connector HDMI Type Follows SDI out Audio Monitoring Output Number Connector
One (Select from sixteen channels) 3.5 mm stereo mini jack
General Specifications Size Weight Power Temperature Range Relative Humidity Altitude
5.625” W x 1.7” H x 5.5” D (143 mm x 40 mm x 140 mm) including connectors 1 lb 8 oz 12 volts, 12 watts (100-230 VAC modular power supply) 0 to 40° C ambient (all specs met) 0 to 95%, non-condensing 0 to 10,000 ft.
BrightEye 90 HD Up/Down/Cross Converter and ARC with AES Audio
HD/SD SDI Out
Composite or Tri-Level Ref In
SDI Driver Genlock
HD/SD SDI/Composite Video In
Analog Decoder Auto-Selecting
Up/Down/Cross Conversion
Audio Mux
SDI Receiver Audio Demux
AES Digital Audio Inputs/Outputs Ch 1/2
Composite Encoder (SD Only)
AES Receivers
Ch 3/4
HDMI Xmtr
Audio Processing
Monitor Amp
Ch 5/6 Ch 7/8 AES Transmitters
Composite Out
HDMI Out Headphone Jack
Tie Back To AES I/O Ports
Audio I/O selectable as: Mux 8 = 8 inputs or Mux 4 = 4 in/4 out or Demux = 8 outputs Provides embedded pass through of all 16 audio channels
37
BrightEye 90-A HD Up/Down/Cross Converter and ARC with Analog Audio Easy To Use
Cross Conversion
BrightEye 90-A is a versatile up/down/cross converter or aspect ratio converter for use with analog and digital video signals. The Swiss Army Knife™ of video conversion, the BrightEye 90-A is a realtime processor that changes video formats without rendering. Simply set the BrightEye 90-A to output your event or facility's preferred HD or SD standard. The BrightEye 90-A will accommodate whatever input you connect – analog composite, SD SDI or HD SDI. After setting the output standard, BrightEye 90-A automatically converts the selected input to the correct standard for your event. The HDMI, SDI and composite outputs are all extremely high quality, suitable for any part of your signal chain. BrightEye 90-A will upconvert, downconvert, cross convert, or act as an ARC, as needed. A special Mirror Flip Output mode can be enabled, causing the output image to be flipped left to right for use with on-stage talent. The built-in Frame Synchronizer allows you to feed asynchronous signals to the BrightEye 90-A. An external reference input allows genlock to a house reference. All vertical interval data and closed captioning is faithfully passed.
It’s easy to convert between various HD standards, whether 720p or 1080i. Simply select the output standard you need and connect the input – that’s all there is to it. Using the Manual Scaling controls allows video sizing necessary for picture-in-picture insertion or web distribution.
Upconverting to High Definition Feed the analog composite or SD SDI output of a camera to a BrightEye 90-A and upconvert to HD. You can take the HDMI and HD SDI signals from the BrightEye 90-A into your switcher or projection system. Upconverting existing SD equipment lets you leverage the equipment you already have and operate in the HD domain. While some cameras may have firewire out, using the video output and upconverting before distribution is preferable since longer cable runs can be achieved and quality is superior. Additionally, the BrightEye 90-A’s reference input allows you to time the upconverted video output for use with a production switcher.
Downconverting to Standard Definition BrightEye 90-A will downconvert any type of HD signal and provides SD SDI, HDMI and an analog composite output, all suitable for broadcast or monitoring.
38
Aspect Ratio Conversion For converting between SD 4:3 and HD 16:9, BrightEye 90-A has you covered. Just select the output standard you need and connect the input.
Audio Processing Made Simple BrightEye 90-A handles both embedded audio and eight channels of analog audio. Sixteen channels of embedded audio are supported in BrightEye 90-A. If the incoming video has embedded audio, the audio will be safely bypassed around the video processing and lipsync will be preserved. Audio mixing is available for two of the four embedded groups of audio. The analog audio I/O ports can be configured for eight channels of incoming audio or for eight channels of audio output. The audio mixer can be used for analog audio as well. Mixer controls are accessed through BrightEye Mac or PC software.
Easy Audio Monitoring Audio monitoring is easy with BrightEye 90-A’s convenient 3.5 mm mini jack. Select the audio channels you want to monitor from the front panel and plug in a headset.
Front Panel and Software Control Input selection, gain control, and test pattern controls are provided through the front panel interface. Audio presence LEDs indicate which channels are detected. Controls for crop, letterbox and pillarbox are accessed from the front panel or BrightEye Mac or PC software. Video and audio levels and the audio mixer can be adjusted through BrightEye Mac or PC software.
BrightEye 90-A HD Up/Down/Cross Converter and ARC with Analog Audio
Features • Use with Cameras and Projection Systems • Turn Analog Camera into Digital HD Source • High Quality HDMI Output • HD and SD Digital and Analog Composite Video I/O • Analog Audio I/O • Analog Audio Monitor Output • Mirror Output Mode for On-Stage Talent • Graticule and Safe Title Generator • Frame Sync • 12 and 16 Bit Processing • Passes Embedded Audio
39
BrightEye 90-A HD Up/Down/Cross Converter and ARC with Analog Audio Analog Video Input Number Type Resolution Impedance Return Loss Input DC Input Hum
HD Standards Supported One Analog Composite PAL or NTSC Digitized at 12 bits 75 Ω >40 dB +/-1 volt DC <100 mV
Serial Digital Input Number Signal Type
One 270 Mb/s SD Serial Digital (SMPTE 259M) or 1.485 Gb/s HD Serial Digital (SMPTE 274M or 296M) Impedance 75 Ω Return Loss >15 dB Max Cable Length 300 meters for 270 Mb/s 100 meters for 1.485 Gb/s Automatic Input Cable Equalization Reference Input Number Type Impedance Return Loss
One 1 V P-P Composite Video, PAL or NTSC or Tri-Level Sync 75 Ω >40 dB
Analog Video Output Number Type Delay Return Loss Output
One Composite PAL or NTSC Adjustable from 1 field to 1 frame >40 dB DC <100 mV
Serial Digital Output Number Type Delay Processing Impedance Return Loss Max Cable Length
40
Two HD Serial Digital 1.485 Gb/s SMPTE 274M, 292M or 296M or SD Serial Digital 270 Mb/s SMPTE 259M Adjustable from 1 field to 1 frame 12 and 16 bit 75 Ω >15 dB 100 meters for HD 300 meters for SD (Belden 1694A)
1080i (SMPTE 274M -4,5,6) 50, 59.94 or 60 Hz 720p (SMPTE 296M -1,2,3) 50, 59.94 or 60 Hz 1080p (SMPTE 274M -9,10,11) 23.98, 24, 25 Hz 1080sF (RP211 -14,15,16) 23.98, 24, 25 Hz Analog Audio Inputs Number Eight (selectable as inputs or outputs) Type Balanced Impedance >15K Ω Max Input Level 24 dBu CMRR >60 dB, 20 Hz to 10 KHz Quantization 24 bits, 128 x oversampled Sample Rate 48 KHz Reference Level -10 dBu or +4 dBu Frequency Response ±0.1 dB, 20 Hz to 20 KHz Crosstalk <106 dB Dynamic Range >106 dB Analog Audio Outputs Number Type Impedance Maximum Output Level Resolution`n Reference Level Frequency Response Crosstalk Dynamic Range
Eight (selectable as inputs or outputs) Balanced, transformerless 30 Ω 24 dBu 24 bits, 128 x oversampled -10 dBu or +4 dBu ± 0.1 dB, 20 Hz to 20 KHz <106 dB >106 dB
Embedded Output (In Serial Output) Group Assign Channels Bit Depth
Two of four groups Sixteen passed 24 Bit
HDMI Output Number One Connector HDMI Type Follows SDI out Audio Monitoring Output Number Connector
One (select from sixteen channels) 3.5 mm stereo mini jack
BrightEye 90-A HD Up/Down/Cross Converter and ARC with Analog Audio General Specifications Size Weight Power Temperature Range Relative Humidity Altitude
5.625” W x 1.7” H x 5.5” D (143 mm x 40 mm x 140 mm) including connectors 1 lb 8 oz 12 volts, 15 watts (100-230 VAC modular power supply) 0 to 40° C ambient (all specs met) 0 to 95%, non-condensing 0 to 10,000 ft.
HD/SD SDI Out Composite or Tri-Level Ref In
SDI Driver Genlock
HD/SD SDI/Composite Video In
Analog Decoder Auto-Selecting
Up/Down/Cross Conversion
Audio Mux
SDI Receiver
Balanced Analog Audio Inputs
Audio Demux
Composite Encoder (SD Only)
Ch 1/2 Ch 3/4 Ch 5/6
24 bit Audio ADC
HDMI Out
HDMI Xmtr
Audio Processing
Headphone Jack
Monitor Amp
Ch 7/8 Ch 1/2
Audio I/O selectable as: Mux 8 = 8 inputs or Mux 4 = 4 in/4 out or Demux = 8 outputs
24 bit Audio DAC
Composite Out
Balanced Audio Outputs
Ch 3/4 Ch 5/6 Ch 7/8
Provides embedded pass through of all 16 audio channels
41
BrightEye 91 HD Upconverter with AES Audio Easy To Use
Audio Monitoring
BrightEye 91 is an upconverter with analog composite and SD SDI inputs. Feed the analog composite or SD SDI output of a camera or playout device to a BrightEye 91 and upconvert to HD. You can take the HDMI and HD SDI signals from the BrightEye 91 into your switcher or projection system. Upconverting existing SD equipment lets you leverage the equipment you already have and operate in the HD domain.
Audio monitoring is easy with BrightEye 91’s convenient 3.5 mm mini jack. Just select the audio channels you want to monitor from the front panel and plug in a headset.
A special Mirror Flip Output mode can be enabled, causing the output image to be flipped left to right for use with on-stage talent, making interaction with what's on screen easy. An external reference input allows genlock to a house reference. All vertical interval data and closed captioning is faithfully passed.
Upconvert Before Distribution While some cameras may have firewire out, using the video output and upconverting before distribution is preferable since longer cable runs can be achieved and quality is superior. Additionally, the BrightEye 91’s reference input allows you to time the upconverted HD SDI video output for use with a production switcher.
Audio Processing BrightEye 91 handles both embedded audio and discrete AES digital audio inputs. Sixteen channels of embedded audio are supported in BrightEye 91. If the incoming video has embedded audio, the audio will be safely bypassed around the video processing and lipsync will be preserved. Audio mixing is available for two of the four embedded groups of audio.
42
Front Panel and Software Control Input selection, gain control, and test pattern controls are provided through the front panel interface. Audio presence LEDs indicate which channels are detected. Controls for crop, letterbox and pillarbox are accessed from the front panel or BrightEye Mac or PC software. Video and audio levels and the audio mixer can be adjusted through BrightEye Mac or PC software.
BrightEye 91 HD Upconverter with AES Audio
Features • Use with Cameras and Projection Systems • Turn Analog Camera into Digital HD Source • High Quality HDMI Output • SD Digital and Analog Composite Video Inputs • AES Inputs • Analog Audio Monitor Output • Mirror Output Mode for On-Stage Talent • Graticule and Safe Generator • Frame Sync • 12 and 16 Bit Processing • Passes Embedded Audio
43
BrightEye 91 HD Upconverter with AES Audio Analog Video Input Number Type Resolution Impedance Return Loss Input DC Input Hum
AES/EBU Digital Inputs One Analog Composite PAL or NTSC Digitized at 12 bits 75 Ω >40 dB +/-1 volt DC <100 mV
Serial Digital Input Number One Signal Type 270 Mb/s SD Serial Digital (SMPTE 259M) Impedance 75 Ω Return Loss >15 dB Max Cable Length 300 meters for 270 Mb/s Automatic Input Cable Equalization Reference Input Number Type Impedance Return Loss
One 1 V P-P Composite Video PAL or NTSC or Tri-Level Sync 75 Ω >40 dB
Serial Digital Output Number Type Delay Processing Impedance Return Loss Max Cable Length
Two HD Serial Digital 1.485 Gb/s SMPTE 274M, 292M or 296M Adjustable from 1 field to 1 frame 12 and 16 bit 75 Ω >15 dB 100 meters for HD
HD Standards Supported 1080i (SMPTE 274M -4,5,6) 50, 59.94 or 60 Hz 720p (SMPTE 296M -1,2,3) 50, 59.94 or 60 Hz 1080p (SMPTE 274M -9,10,11) 23.98, 24, 25 Hz 1080sF (RP211 -14,15,16) 23.98, 24, 25 Hz
44
Number Four (total of eight channels) (selectable as inputs or outputs) Type AES3id Connector Coaxial, 75 Ω Bit Depth 20 and 24 Bit Sample Rate 30 KHz to 96 KHz (Sample Rate Converted internally to 48 KHz) Reference Level -18 or -20 dBFS (selectable) AES/EBU Digital Outputs Number Four (total of eight channels) (selectable as inputs or outputs) Type AES3id Delay Adjustable from 1 field to 1 frame Connector Coaxial, 75 Ω Bit Depth 24 Bit Sample Rate 48 KHz, synchronous to video output Reference Level -18 or -20 dBFS (selectable) Embedded Output (In Serial Output) Group Assign Channels Bit Depth
Two of four groups Sixteen passed 24 Bit
HDMI Output Number One Connector HDMI Type Follows SDI out Audio Monitoring Output Number Connector
One (select from sixteen channels) 3.5 mm stereo mini jack
General Specifications Size Weight Power Temperature Range Relative Humidity Altitude
5.625” W x 1.7” H x 5.5” D (143 mm x 40 mm x 140 mm) including connectors 1 lb 8 oz 12 volts, 11 watts (100-230 VAC modular power supply) 0 to 40° C ambient (all specs met) 0 to 95%, non-condensing 0 to 10,000 ft.
BrightEye 91 HD Upconverter with AES Audio
Composite or Tri-Level Ref In
HD SDI Out Genlock
SD SDI/Composite Video In
SDI Driver
Analog Decoder Auto-Selecting
Upconversion
Audio Mux
SDI Receiver Audio Demux
AES Digital Audio Inputs
Ch 1/2
AES Receivers
Ch 3/4
HDMI Xmtr
Audio Processing
Monitor Amp
Ch 5/6 Ch 7/8
AES Transmitters
HDMI Out Headphone Jack Tie Back To AES I/O Ports
Audio I/O selectable as: Mux 8 = 8 inputs or Mux 4 = 4 in/4 out or Demux = 8 outputs Provides embedded pass through of all 16 audio channels
45
Scan Converters BrightEye Mitto BrightEye Mitto BrightEye Mitto BrightEye Mitto BrightEye Mitto BrightEye Mitto
3G Scan Converter (BEM-1) 3G Fiber Scan Converter (BEM-1F) HD Scan Converter (BEM-2) HD Fiber Scan Converter (BEM-2F) Pro Fiber Scan Converter (BEM-3F) Pro 2 Scan Converter (BEM-4)
Routers New BrightEye NXT 410 Clean HDMI Router New BrightEye NXT 415 Compact Router New BrightEye NXT 430 Compact Clean Router HDMI Converters BrightEye Mitto BrightEye Mitto BrightEye Mitto BrightEye Mitto BrightEye Mitto BrightEye Mitto BrightEye 72 BrightEye 72-F BrightEye 81 BrightEye 81-F BrightEye 83 BrightEye 83-F BrightEye 90 BrightEye 90-A BrightEye 90-F BrightEye 90-FA BrightEye 91 BrightEye 91-A BrightEye 92-A BrightEye 92-M BrightEye 93 BrightEye 94
3G Scan Converter (BEM-1) 3G Fiber Scan Converter (BEM-1F) HD Scan Converter (BEM-2) HD Fiber Scan Converter (BEM-2F) Pro Fiber Scan Converter (BEM-3F) Pro 2 Scan Converter (BEM-4) 3G/HD/SD SDI to HDMI Converter Optical 3G/HD/SD SDI to HDMI Converter 3G/HD/SD SDI to HDMI Converter Optical to HDMI and 3G/HD/SD SDI Electrical Converter HDMI to 3G/HD/SD SDI Converter HDMI to Optical and Electrical 3G/HD/SD SDI Converter HD Up/Down/Cross Converter and ARC with AES Audio HD Up/Down/Cross Converter and ARC with Analog Audio HD Up/Down/Cross Converter and ARC w/ AES Audio and Optical Output HD Up/Down/Cross Converter and ARC with Analog Audio and Optical Output HD Upconverter with AES Audio HD Upconverter with Analog Audio HD Downconverter with Analog Audio HD Downconverter HD Cross Converter SD Aspect Ratio Converter
High Definition Video BrightEye Mitto BrightEye Mitto BrightEye Mitto BrightEye Mitto BrightEye Mitto BrightEye Mitto BrightEye 11-HD BrightEye 41 BrightEye 42 BrightEye 43 BrightEye 46 BrightEye 48 BrightEye 56 BrightEye 57 BrightEye 70 BrightEye 71 BrightEye 71-F BrightEye 72
46
3G Scan Converter (BEM-1) 3G Fiber Scan Converter (BEM-1F) HD Scan Converter (BEM-2) HD Fiber Scan Converter (BEM-2F) Pro Fiber Scan Converter (BEM-3F) Pro 2 Scan Converter (BEM-4) HD/SD SDI to Analog Converter Video/AES/Tri-Level Sync Distribution Amplifier HD/SD/ASI Distribution Amplifier 3G/HD/SD/ASI Distribution Amplifier 3G/HD/SD/ASI Electrical to Optical Converter 3G/HD/SD/ASI Optical to Electrical Converter HD/SD/Analog Test Signal and Sync Pulse Generator 3G/HD/SD/Analog Test Signal and Sync Pulse Generator HD/SD AES Embedder/Disembedder HD/SD 8 Channel Analog Audio Embedder/Disembedder HD/SD 8 Channel Analog Audio Embedder/Disembedder with Optical Out 3G/HD/SD SDI to HDMI Converter
High Definition Video (continued) BrightEye 72-F BrightEye 73 BrightEye 74 BrightEye 75 BrightEye 76 BrightEye 81 BrightEye 81-F BrightEye 83 BrightEye 83-F BrightEye 90 BrightEye 90-A BrightEye 90-F BrightEye 90-FA BrightEye 91 BrightEye 91-A BrightEye 92-A BrightEye 92-M BrightEye 93 BrightEye 94
Optical 3G/HD/SD SDI to HDMI Converter HD/SD AES Embedder with Optical Out Optical Disembedder with HD/SD Electrical Out HD/SD Analog to Digital Video Converter HD/SD Analog to Digital Video Converter with Optical Out 3G/HD/SD SDI to HDMI Converter Optical to HDMI and 3G/HD/SD SDI Electrical Converter HDMI to 3G/HD/SD SDI Converter HDMI to Optical and Electrical 3G/HD/SD SDI Converter HD Up/Down/Cross Converter and ARC with AES Audio HD Up/Down/Cross Converter and ARC with Analog Audio HD Up/Down/Cross Converter and ARC with AES Audio and Optical Output HD Up/Down/Cross Converter and ARC with Analog Audio and Optical Output HD Upconverter with AES Audio HD Upconverter with Analog Audio HD Downconverter with Analog Audio HD Downconverter HD Cross Converter SD Aspect Ratio Converter
3 Gb/s High Definition Video BrightEye Mitto BrightEye Mitto BrightEye 43 BrightEye 46 BrightEye 48 BrightEye 57 BrightEye 72 BrightEye 72-F BrightEye 81 BrightEye 81-F BrightEye 83 BrightEye 83-F
3G Scan Converter (BEM-1) 3G Fiber Scan Converter (BEM-1F) 3G/HD/SD/ASI Distribution Amplifier 3G/HD/SD/ASI Electrical to Optical Converter 3G/HD/SD/ASI Optical to Electrical Converter 3G/HD/SD/Analog Test Signal and Sync Pulse Generator 3G/HD/SD SDI to HDMI Converter Optical 3G/HD/SD SDI to HDMI Converter 3G/HD/SD SDI to HDMI Converter Optical to HDMI and 3G/HD/SD SDI Electrical Converter HDMI to 3G/HD/SD SDI Converter HDMI to Optical and Electrical 3G/HD/SD SDI Converter
Analog to Digital Converters BrightEye 1 BrightEye 2 BrightEye 3 BrightEye 25 BrightEye 26 BrightEye 75 BrightEye 76
Analog/SD SDI to SD SDI/Optical Converter with TBC and Frame Sync Analog to SD SDI Converter Analog to SD SDI Converter with TBC and Frame Sync Analog Video/Audio to SD SDI Converter with TBC and Embedder Analog Video/Audio to SD SDI/Optical Converter with TBC and Embedder HD/SD Analog to Digital Video Converter HD/SD Analog to Digital Video Converter with Optical Out
Digital to Analog Converters BrightEye 11 BrightEye 11-HD BrightEye 15 BrightEye 16 BrightEye 72
SD SDI to Analog Converter HD/SD SDI to Analog Converter SD SDI to Analog Converter with Frame Sync/Genlock SD SDI to Analog Converter with Frame Sync/Genlock and Audio Disembedder 3G/HD/SD SDI to HDMI Converter
47
Audio Embedders, Disembedders, and Converters BrightEye 20 BrightEye 21 BrightEye 22 BrightEye 23 BrightEye 24 BrightEye 25 BrightEye 26 BrightEye 30 BrightEye 30-D BrightEye 70 BrightEye 71 BrightEye 71-F BrightEye 72 BrightEye 72-F BrightEye 73 BrightEye 74 BrightEye 75 BrightEye 76
Analog Audio/AES Embedder or Disembedder AES/SD SDI Embedder SD SDI/AES Disembedder Analog Audio/SD SDI Embedder SD SDI to Analog Converter and Disembedder Analog Video/Audio to SD SDI Converter with TBC and Embedder Analog Video/Audio to SD SDI/Optical Converter with TBC and Embedder Audio ADC and DAC, Bidirectional Audio ADC and DAC, Bidirectional Converter with Delay HD/SD AES Embedder/Disembedder HD/SD 8 Channel Analog Audio Embedder/Disembedder HD/SD 8 Channel Analog Audio Embedder/Disembedder with Optical Out 3G/HD/SD SDI to HDMI Converter Optical 3G/HD/SD SDI to HDMI Converter HD/SD AES Embedder with Optical Out Optical Disembedder with HD/SD Electrical Out HD/SD Analog to Digital Video Converter HD/SD Analog to Digital Video Converter with Optical Out
Distribution Amplifiers BrightEye 33 BrightEye 40 BrightEye 41 BrightEye 42 BrightEye 43
Analog Audio Distribution Amplifier SD SDI Reclocking Distribution Amplifier Video/AES/Tri-Level Sync Distribution Amplifier HD/SD/ASI Distribution Amplifier 3G/HD/SD/ASI Distribution Amplifier
ASI BrightEye 42 BrightEye 43 BrightEye 46 BrightEye 48
HD/SD/ASI Distribution Amplifier 3G/HD/SD/ASI Distribution Amplifier 3G/HD/SD/ASI Electrical to Optical Converter 3G/HD/SD/ASI Optical to Electrical Converter
Fiber Optic BrightEye Mitto BrightEye Mitto BrightEye Mitto BrightEye 1 BrightEye 10 BrightEye 26 BrightEye 46 BrightEye 48 BrightEye 71-F BrightEye 72-F BrightEye 73 BrightEye 74 BrightEye 76 BrightEye 81-F BrightEye 83-F BrightEye 90-F BrightEye 90-FA
3G Fiber Scan Converter (BEM-1F) HD Fiber Scan Converter (BEM-2F) Pro Fiber Scan Converter (BEM-3F) Analog/SD SDI to SD SDI/Optical Converter with TBC and Frame Sync Optical/SD SDI to Analog/SDI Converter Analog Video/Audio to SD SDI/Optical Converter with TBC and Embedder 3G/HD/SD/ASI Electrical to Optical Converter 3G/HD/SD/ASI Optical to Electrical Converter HD/SD 8 Channel Analog Audio Embedder/Disembedder with Optical Out Optical 3G/HD/SD SDI to HDMI Converter HD/SD AES Embedder with Optical Out Optical Disembedder with HD/SD Electrical Out HD/SD Analog to Digital Video Converter with Optical Out Optical to HDMI and 3G/HD/SD SDI Electrical Converter HDMI to Optical and Electrical 3G/HD/SD SDI Converter HD Up/Down/Cross Converter and ARC with AES Audio and Optical Output HD Up/Down/Cross Converter and ARC with Analog Audio and Optical Output
Sync Pulse/Test Signal Generators BrightEye 54 BrightEye 55 BrightEye 56 BrightEye 57 48
Sync Generator and Test Signal Generator Genlockable Sync Generator and Test Signal Generator HD/SD/Analog Test Signal and Sync Pulse Generator 3G/HD/SD/Analog Test Signal and Sync Pulse Generator
Our Commitment to You: • Free software upgrades for life • 24/7 technical support • Five-year warranty • Everything is designed and built in California by Ensemble Designs Sales and Technical Support +1 530.478.1830 FAX +1 530.478.1832
Mailing Address Ensemble Designs
PO Box 993 Grass Valley CA 95945 USA
Shipping Address Ensemble Designs
870 Gold Flat Rd. Nevada City CA 95959 USA
Web and Online Support:
Ensemble Designs Product and Customer Service Support www.ensembledesigns.com/support.html
[email protected] Ensemble Designs Sales
[email protected] Due to ongoing product development, all specifications are subject to change.
Five-Year Warranty
We warrant our products for a period of five years from purchase to be free of defects in materials and workmanship. During the warranty period products will be repaired or replaced at our discretion. Warranty work is performed at Ensemble Designs.
Printed in the USA
May 2013
49
Who is Ensemble Designs? By Engineers, For Engineers In 1989, a former television station engineer who loved designing and building video equipment, decided to start a new company. He relished the idea of taking an existing group of equipment and adding a few special pieces in order to create an even more elegant ensemble. So, he designed and built his first product and the company was born. Focused On What You Need As the company has grown, more engineers have joined Ensemble Designs and this wealth of practical experience fuels the company’s innovation. Everyone at the company is focused on providing the very equipment you need to complete your ensemble of video and audio gear. We offer those special pieces that tie everything together so that when combined, the whole ensemble is exactly what you need. Notably Great Service for You We listen to you – just tell us what you need and we’ll do our best to build it. We are completely focused on you and the equipment you need. Being privately held means we don’t have to worry about a big board of directors or anything else that might take attention away from real business. And, you can be sure that when you call a real person will answer the phone. We love this business and we’re here to stay.
The Academic Medical Centre of Amsterdam uses BrightEye Mittos and BrightEye video converters for their medical school campuses. They take DVI or HDMI out of endoscopes and ultrasounds and use BrightEye Mitto to convert to high detail, broadband video for the AMC and University. “I was walking down the aisle at IBC and the Ensemble Mitto caught my eye,” said Jaap Tuyp, Technical Manager of the AVC at University of Amsterdam. “I wanted to know how Ensemble could make just a small portion of the computer screen full-screen HD with such good quality.” Now their system uses over 100 Ensemble BrightEye scan converters, video converters and fiber converters. The university creates medical programming and live classes that are used all over the world.
Bricks and Mortar of Your Facility The bricks and mortar of a facility include pieces like video converters, up/downconverters, audio embedders, switchers, routers, protection switches, multiviewers and SPGs for SD, HD and 3 Gb/s. That’s what we’re focused on, that’s all we do – we make proven and reliable signal processing and infrastructure gear for video facilities worldwide, for you. Come on by and visit us. Drop in for lunch and a tour!
BrightEye video and audio converters, scan converters, and audio embedders are used worldwide in broadcast, mobile, production, and post. Reliable and easy to use.
50
May 2013
And consider our Avenue product line when you need modular video and audio processing.
PO Box 993, Grass Valley CA 95945 USA Tel +1 530.478.1830 www.ensembledesigns.com
