Transcript
2. Mount Timer
1. Select Location
3. Connect sprinkler valves to timer wires Common Wire
MOUNTING TEMPLATE GABARIT D`INSTALLATION GUIA DE COLGAR
4.17” (106mm)
.
.
. .
. . .
.
.
.
.
. .
.
. .
.
.
. .
.
.
.
.
dimensions: flat: w: 9"
Valve
Printers are responsible for
h: 7"
finished: w 9"
d: 0"
meeting print production requirements. Any changes
h 7"
FF O
BUDGET
Use included mounting template to mark screw locations. des: SM spck: SM
job no: 07WTM005259
must be approved by the
colors
Registration
crop color non printing
color non printing
K
PMS ????
PMS ????
client and Fluid Studio. printed piece must meet designated specifications
client: Orbit sku: 57880
p 801 295 9820 f 801 951 5815
.
.
3
date: 10.05.07
.
.
. .
.
.
.
.
.
.
.
. .
.
.
. .
.
.
.
. .
.
.
. .
.
.
.
.
upc: ? ????? ????? ?
www.fluid-studio.net
file name: 07WTM005259
1065 South 500 West Bountiful, Utah 84010
software: Illustrator CS2
57880-04 rA.indd
on this form.
additional instructions: · ·
PMS ????
© 2007 Fluid Studio. This work is the property of Fluid Studio, and cannot be used, reproduced or distributed in any way without their express permission.
Connect one of the two wires from each valve to the common wire leading to the timer (usually white). Connect the other wire from each valve to one of the colored wires leading to the timer.
. .
Keyhole 3 mm
Clean, dry, and out of direct sunlight PROGRAM
Allow 23 cm clearance for the swing door
RAIN DELAY
RESET
No. 8 Screw
BUDGET
FF
AUTO
O
ST TI AR M T E
SET DATE
C SE LO T C K
O HO FT W EN
.
.
.
proof no:
RUN TIME
.
.
W N
.
. .
.
AUTO
O HO FT E
.
.
.
.
.
Solenoid
RUN TIME
.
.
.
ST TIM AR T E
.
.
C SE LO T C K
SET DAY
timer quick start guide . .
To Timer
Wire Nut
Indoor
Or Pre-formed mounting holes
Wall
4. Connect valve wire to terminal Do not connect to power source until after wiring valves to timer Only connect one valve to each terminal (station)
Hang timer on screw using keyhole.
Outdoor
Station 1
Strip wire Push in
Level .
Required Tools:
For detailed instructions on outdoor wiring, see manual page 8
Phillips Screwdriver
Warning: Check state and local codes. Orbit recommends using a licensed electrical contractor for outdoor wiring of timer.
Wire Strippers
Push tab upward to release wire
Screw through one of the pre-formed mounting holes.
PN 96894-50 rA
proof no:
1
date: 05.19.10 des: SM spck: XX job no: NA
dimensions:
Printers are responsible for meeting print production requirements. Any changes must be approved by the client and Fluid Studio. printed piece must meet designated specifications on this form.
flat: w: 16" h: 14" finished: w 16" d: " h 14" colors Registration
fold color non printing
color non printing
K
PMS ????
PMS ????
client: Orbit sku: 96894 p 801 295 9820 f 801 951 5815 www.fluid-studio.net 1065 South 500 West Bountiful, Utah 84010
upc: NA file name: 96894-50 rA.indd software: InDesign CS3
additional instructions: · Font sizes cannot be smaller than 7 pt. · Accordian Fold
PMS ????
© 2007 Fluid Studio. This work is the property of Fluid Studio, and cannot be used, reproduced or distributed in any way without their express permission.
5. Connect to Electrical Power
7. Program Timer Reset
Battery
A
Set Current Time (e.g. pacific, mountain standard)
Indoor C PROGRAM
F RAIN DELAY
RESET
B
G ST TI AR M T E
BUDGET
O
A
B
H
SET DATE
Outdoor PROGRAM
RAIN DELAY
K
FF
BUDGET
6. Activate Battery
A
Enter - To confirm a new setting Manual - To water manually
B
clear - To clear a setting
C
program - to switch between programs - A, B, and C
D
ARROW [] - To skip to the next setting / watering station or move to other programs/settings
E
ARROW [] - To go back to the previous setting / watering station or move to other programs/settings
F
rain delay - To pause operation for 24-72 hours due to rain or other factors
G
[ + ] - To increase a numeric setting
H
[ -] - To decrease a numeric setting
D
Select Watering Duration Set for each station then press enter
Turn dial to run time enter the watering duration (+/- ) for each station (enter or arrow to move between stations)
E
O HO FT W EN
BUDGET
Set Start Time Time to begin watering
Turn dial to start time to enter the time to begin watering (+/-)
RUN TIME
FF
Remove plastic strip to activate battery
ST TI AR M T E
SET DATE
AUTO
O
C
Button Function:
Warning: See manual for outdoor wiring instructions
C SE LO T C K
Turn dial to set date enter current date (+/-) (enter or arrows will advance)
O HO FT W EN
.
RAIN DELAY
Swing Out Panel Release
RUN TIME
O
Indicator
ST TIM AR T E
SET DAY
C SE LO T C
AUTO
PROGRAM
Set Date
O HO FT W EN
FF
AUTO
Turn dial to set clock enter current time (+/-) D
RUN TIME
E
SET DATE
C SE LO T C K
Set Watering Days or Interval
Dial Position Function:
One Lithium CR2032 battery (included) is required to retain the program in memory during power loss. Annual replacement is recommended. Remove the plastic strip to activate the pre-installed battery.
I
Auto - Watering mode
J
Set Clock - Set calendar and clock time
K
Set Date - Year, Month, and Day
L
Start Time - Set time to begin watering
M
Run Time - Set watering duration for each station
N
How Often - Set frequency of watering days
O
Budget - Adjust overall watering as a percentage
P
Off - Turn all stations off
Turn dial to how often to select watering days (arrows to move and enter to select)
F
Set Auto Mode
help 1-800-488-6156 or 1-801-299-5555
www.orbitonline.com Turn dial to auto—you have programmed your timer!
(See page 9 of manual for detailed instructions on programming.)
Before returning this sprinkler timer to the store, contact Orbit® Technical Service at: 1-800-488-6156, 1-801-299-5555
