Transcript
User’s Manual TM-70
Chapter 1 Introduction 1.1 About the Products 1.2 Specification
Chapter 2 Hardware Setup 2.1 Unpacking Touch monitor 2.2 Product Overview 2.3 Main Unit 2.4 Rear View 2.5 Internal layout 2.6 MSR Installation 2.7 Customer Display Installation
Chapter 3 Driver Installation 3.1 Installing the touch driver 3.2 Installing the MSR Utility
Chapter 4 OSD Operation 4.1 On-Screen Display (OSD) Menus
Chapter 1 Introduction 1.1 About the Products The LCD Desktop Touch monitor is a 12” / 15” TFT color display with the following features: - Direct analog screen input - 167 million displayable colors - High resolution - XGA / SVAGA / VGA / VESA / Mac compatible - 30 ~ 62KHz horizontal scan - 56 ~ 75 HZ refresh rate - Auto adjustment capability - High quality full screen re-scaling - Multilingual OSD menus: English, French, Germany, Spanish, Japanese and Chinese. - Serial / USB touch interface - Built in speakers - Optional Fujitsu / Higgstec touch panel. - VESA DDC 1/28B data communication - Stand with minimum 20 ~ 90° angle of tilt. - OSD and power button lockouts
1.2 Specification Display Model LCD Size Brightness Resolution Touch Screen Tilt Angle VGA Serial PS2 Keyboard Speaker Power Supply Compliance Weight Dimension Operating Temp
TM150 TM120 15" 12.1" 250 cd/m2 300 cd/m2 1024x768 800x600 5 / 7-wire Resistive Type 20° to 90° I/O Ports 15pin D-SUB x1 RS232 x 2 ( For Touch Panel / MSR & I-Button Key ) 1 (For MSR & I-Button) Internal 2W x2 Others Internal Adapter 12VDC, 50W CE / FCC Class B Approx. 6.0 Kgs 370(W) x 277(L) x 355(H) 313(W) x 274(L) x 318(H) mm mm 5°C to 40°C
Chapter 2 Hardware Set up
2.1 Unpacking the touch monitor Check that the following 4 items are presented and in good conditions: a. Main Unit
b. CD: Quick Guide & Driver Bank
c. Power Cord: USA, Europe, UK
d. Option Item d1. Customer Display: RS232 port, pin 9 was power input 12VDC.
d2. MSR (Magnetic Stripe Reader): 2/3 tracks, KB / RS232 option.
d3. MSR and I-BOTTOM: 2 in 1 Module, MSR with Dallas Key Reader.
2.2 Product Overview a. Front View
Control Pad: Power button, Menu select, + - Key Adjust, Auto Set b. Rear View
1. 2. 3. 4. 5. 6. 7.
Power cable: 110V/220V VGA cable (15 pin D Sub): Connect with VGA port of PC. Touch cable (COM, 9 pin D Sub): Connect with RS232 port of PC. MSR (Optional, COM, 9 pin D Sub) - Connect with RS232 port of PC. Touch USB (Optional) - Connect with USB port of PC. MSR (Optional, Keyboard) – Connect with PC Keyboard self and Keyboard port Audio Input.
c. Internal Layout
1. 2. 3. 4. 5. 6. 7.
USB: optional touch control board connection. COM1 for standard touch control board. COM2 for optional RS232 type MSR. PS2 for optional Key Board type MSR. VGA. AUDIO in. POWER in.
d. MSR Installation d1. Release the 2 screws of main body from rear side of bezel.
d2. Disassembly EMI Chassis & Cable Clipper, insert and connect the MSR cable. Then recover the Chassis and Cable Clipper.
d3. Remove the MSR cover on right side of monitor. Install the MSR module by 3 screws. Finally connect the MSR cable to CN1( refer to Internal Layout ).
e. Customer Display Installation Remove the cover pad, then install the pole tube and customer display, connect the cable with the RS232 port (pin 9 with 12V) of PC.
Chapter 3 Driver Installation 3.1 Installing touch driver Touch Systems provide diver software that allows your touch monitor to work with your computer. Drivers are located on the enclosed CD-ROM for the operating systems as WinXP/2000/NT/ME/98/95. 1. Click TM/WTM Series.
2. Click Touch Driver
3. Click FUJITSU TOUCH PANEL.
4. Click FUJITSU Touch Panel Driver (Serial).
5. For single device application, click the drop-down list and select Plug and Play Device, for dual-monitor application, select Non Plug and Play Device
6. Click Continue Anyway.
7. Click OK on the popup message box.
3.2 Installing MSR Utility a. Click the MSR driver as following driver bank.
b. After completed the driver installation, please make a testing MSR function as followings.
c. If MSR doesn’t work, please double check the parameter of protocol as followings.
Chapter 4 OSD Menu Function 4.1 Main Menu Press the “MENU” key, main menu page will show up, press the “UP” or “ADJ. +” AND “Down” or “ADJ. –“ key ( appear pic1 ) to select what function adjustment you need.
pic1 The end of this page will be shown the working resolution and frequency. a. AUTO SET Select AUTO SETUP function active the auto adjusting for the picture.
pic2
b. BRIGHTNESS Select BRIGHTNESS function, press ADJ+ or ADJ- key to increase or decrease backlight current of the inverter.
pic3 c. CONTRAST Select CONTRAST function, press ADJ+ or ADJ- key to increase or decrease video gain of the picture.
pic4 d. DISPLAY Select DISPLAY ADJUST function, enter into the sub-page for adjust display’s function of the picture.
pic5
d1. POSITION Select H.POSITION function, press ADJ+ or ADJ- key to shift left or right the picture in horizontal position.
pic6 d2. V. POSITION Select V.POSITION function, press ADJ+ or ADJ- key to shift up or down the picture in vertical position.
pic7 d3. CLOCK Select CLOCK function, press ADJ+ or ADJ- key to increase or decrease the pixel clock frequency of the picture.
Pic8 d4. PHASE Select PHASE function, press ADJ+ or ADJ- key to shift the pixel clock phase of the picture.
pic9
d5. QUALITY Select QUALITY function, press ADJ+ or ADJ- key to change scanning filter of the picture. If input resolution is best recommend of LCD panel specifications. The function is not working.
d6. RECALL Select RECALL function, which is recall the value for the H. POSITION, V.POSITION, CLOCK, PHASE and QUALITY. d7. RETURN Select RETURN function, return from DISPLAY menu ( Pic5 ) change to MAIN MENU ( Pic1)
e. COLOR TEMPERATURE Select COLOR TEMPERTURE function enter into the sub-page to adjust the display color of the picture
pic11
e1. 9300K Select 9300K function, which is recalling the value for the color temperature of 9300K. e2. 7500K Select 7500K function, which is recalling recall the value for the color temperature of 7500K. e3. 6500K Select 6500K function, which is recalling the value for the color temperature of 6500K. e4. AUTO GAIN Select AUTO GAIN function, which is acting the auto white balance adjusting. e5. RED Select RED function, press ADJ+ or ADJ- key to increase or decrease the R gain in user’s mode of color temperature. 74
pic12 e6. GREEN Select GREEN function, press ADJ+ or ADJ- key to increase or decrease the G gain in user’s mode of color temperature.
96 pic13
e7. BLUE Select BLUE function, press ADJ+ or ADJ- key to increase or decrease the R gain in user’s mode of color temperature.
pic14 e8. RETURN Select RETURN function, return from DISPLAY menu change to MAIN MENU. f. LANGUAGE In this mode, that could into the sub-page (pic15) to select the language for OSD display.
pic15 g. OSD DISPLAY
pic16
g1. OSD H-POS Select OSD H-POS function, press ADJ+ or ADJ- key to shift left or right the horizontal position of OSD display.
pic17 g2. OSD V-POS Select OSD V-POS function, press ADJ+ or ADJ- key to shift up or down the vertical position of OSD display.
pic18 g3. OSD TIMER Select OSD TIME function, press ADJ+ or ADJ- key to increase or decrease the time of OSD display. Except “0” is always display.
pic19 g4. OSD TRANSPARENCY Select OSD TRANSPARENCY function, press ADJ+ or ADJ- key to increase or decrease the transparency of OSD display.
pic20
g5. RECALL Select RECALL function, which is recalling the value for the OSD H-POS, OSD V-POS, OSD TIMER and OSD TRANSPARENCY g6. RETURN Select RETURN function, return from DISPLAY menu change to MAIN MENU. h. VGA / DVI INPUT Select VGA/DVI function, enter into the sub-page to select input source.
pic21 h1. ANALOG INPUT Select ANALOG INPUT function, the input signal from VGA. h2. DIGITAL INPUT Select DIGITAL INPUT function, the input signal from DVI. If no DVI input connector, Signal automatic select VGA input. h3.RETURN Select RETURN function, return from DISPLAY menu change to MAIN MENU. i. AUDIO Select AUDIO function, enter into the sub-page to adjust the audio function.
pic22 i1. MUTE Select MUTE function, which is switching to mute mode of audio. Switch back normal mode by push MENU key again. i2. VOLUME
pic23 i3.RECALL Select RECAL function, which is recalling the value for the MUTE and VOLUME. i4. RETURN Select RETURN function, return from DISPLAY menu to MAIN MENU.
j. Hot Key j1. Directly press the “ Adj +” or “UP” key to switch the mode of audio mute. j2. Directly press the “ Adj -” or “DOWN ” key to adjust the volume of audio output.
