Transcript
TM 9-3416-235-14&P
DEPARTMENT OF THE ARMY TECHNICAL MANUAL
OPERATOR, ORGANIZATIONAL, DIRECT SUPPORT AND GENERAL SUPPORT MAINTENANCE MANUAL INCLUDING REPAIR PARTS LIST
FOR
LATHE, ENGINE: 9-INCH SWING MODEL CL 670Z (SOUTH BEND LATHE) (3416-00-235-0551)
HEADQUARTERS, DEPARTMENT OF THE ARMY DECEMBER 1980
TM 9-3416-235-14&P TECHNICAL MANUAL
HEADQUARTERS DEPARTMENT OF THE ARMY WASHINGTON, DC, 19 December 1980
} No. 9-3416-235-14&P
OPERATOR'S, ORGANIZATIONAL, DIRECT SUPPORT AND GENERAL SUPPORT MAINTENANCE MANUAL INCLUDING REPAIR PARTS LIST FOR LATHE, ENGINE: 9-INCH SWING MODEL CL 670Z (NSN 3416-00-235-0551) REPORTING ERRORS AND RECOMMENDING IMPROVEMENTS You can help improve this manual. If you find any mistakes or if you know of a way to improve the procedures, please let us know. Mail your letter, DA Form 2028 (Recommended Changes to Publications and Blank Forms), or DA Form 2028-2, located in the back of this manual direct to: Commander, US Army Armament Materiel Readiness Command, ATTN: DRSAR-MAS, Rock Island, IL 61299. A reply will be furnished directly to you. NOTE This manual is published for the purpose of identifying an authorized commercial manual for the use of the personnel to whom this lathe is issued. Manufactured by: South Bend Lathe 400 West Sample Street South Bend, Indiana 46621 Procured under Contract No. DAAA09-77-C-6144 This technical manual is an authentication of the manufacturers' commercial literature and does not conform with the format and content specified in AR 310-3, Military Publications. This technical manual does, however, contain available information that is essential to the operation and maintenance of the equipment. i/(ii blank)
INSTRUCTIONS FOR REQUISITIONING PARTS NOT IDENTIFIED BY NSN
When requisitioning parts not identified by National Stock Number, it is mandatory that the following information be furnished the supply officer. 1 - Manufacturer's Federal Supply Code Number - 55985 2 - Manufacturer's Part Number exactly as listed herein. 3 - Nomenclature exactly as listed herein, including dimensions, if necessary. 4 - Manufacturer's Model Number - Model CL 670Z 5 - Manufacturer's Serial Number (End Item) 6 - Any other information such as Type, Frame Number, and Electrical Characteristics, if applicable. 7 - If DD Form 1348 is used, fill in all blocks except 4, 5, 6, and Remarks field in accordance with AR 725-50. Complete Form as Follows: (a) In blocks 4, 5, 6, list manufacturer's Federal Supply Code Number - 55985 followed by a colon and manufacturer's Part Number for the repair part. (b) Complete Remarks field as follows: Noun: (nomenclature of repair part) For: NSN: 3416-00-235-0551 Manufacturer: South Bend Lathe, Inc.
Model: CL 6'707 Serial: (of end item) Any other pertinent information such as Frame Number, Type, Dimensions, etc.
iii
TABLE OF CONTENTS Page Mounting the Motor ...........................................................................................................................................
1
Ordering Replacement Parts .............................................................................................................................
2
Special Information ...........................................................................................................................................
3
Maintenance .....................................................................................................................................................
4
Parts List...........................................................................................................................................................
5-59
iv
1
IMPORTANT your machine, also date the machine was built. Location of these numbers illustrated at right. CODE NUMBER. This number should also appear on your order of replacement part. This number is an index to the specific design of part that went into the unit assembly.
Machine tools are designed and manufactured to assure you the greatest measure of long life performance. There remains, however the important factor of getting prompt service when replacement parts are required as a result of natural wear or accidental damage. This parts list was prepared for your convience to determine quickly the part needed.
We may change the dimension or the appearance of a certain part, yet it is still interchangeable with the old part. You will always receive the benefit of the improved design on orders for replacement parts whenever interchangeability makes this possible. Location of this number (illustrated below) is shown on the repair parts sheet. Therefore, when ordering have the following information: 1. Serial or Model No. of Machine. 2. Unit code number. 3. Part number & name of part required. 4. Quantity.
PARTS AND ASSEMBLIES. Frequently replacement parts are ordered that appear to be individual parts but in reality the particular part ordered is attached to other parts by press fit, hand scraping, tapered pins or by some other mechanical means which can only be properly done in the factory, and are part of an assembly. The part numbers with prefixes and AS identify assemblies and the parts included in these assemblies are indicated by the item numbers appearing in parenthesis after the part name. Such parts are not sent out individually, but as assemblies. SERIAL NUMBER OF LATHE. This number must always appear on your order for replacement parts or attachments to assure prompt shipment of the part or attachment ordered. This number is an index as to the size, type and model of 2
SPECIAL INFORMATION
CARE OF MACHINE TOOILS THAT ARE NOT IN USE
When a machine is taken out of service, such as in a school where they would not be used during the summer months or at some other vacation or off period, it should be properly taken care of as follows: 1. Thoroughly clean the machine, being sure that all surfaces are cleaned. It is as important to clean the painted surfaces as well as the machined surfaces. The machine should be cleaned with some type of solvent if the machine has accumulated hard to remove deposits. If all deposits are not removed and a protective coating is applied, it will make the machine doubly hard to clean when the machine is put back into service. A neutralizing agent should be used where finder printing is common or where the climate is very damp. 2. After the machine has been thoroughly cleaned all of the machined surfaces should be covered with either a good Grade of medium weight MACHINE OIL (NOT AUTO ENGINE OII,) or if the machine is going to be out of service for a long period of time a light weight grease (commercial petroleum jelly that has been thinned with naptha or mineral spirits is very good) should be used. When covering the machine surfaces care should be taken so that the machined surfaces are completely covered. Also you should try and keep the oil and grease off the painted surfaces. 3. If the machine has belts of any type, they should be loosened, so that they will not stretch while the machine is not in use. 4. All power to the machine should be disconnected. Some machines could be very easily damaged if run after being out of service for a long period of time. 5. The machine should be covered with a cover that will keep dust and dirt from accumulating on it. Also the cover should be liquid repellent to keep any liquid from coming into contact with the working parts of the machine. These covers are available for all sizes and types of machines.
3
MAINTENANCE BACK GEAR AND ECCENTRIC SHAFT 9", 10K, 10" and 14½" lathes only
Fig. 2 I. TO DISASSEMBLE: 1. Remove items A and B (Fig. 1). 2. Loosen screw C (Fig. 2). 3. Remove items D thru I (Fig. 2) in alphabetical order. II. TO REASSEMBLE: 1. Replace items H and I. (Be sure gears are free of dirt, chips, and nicks.) 2. Replace item G and pin with item F 3. Replace item E, locating the point of the screw in slot of eccentric shaft bushing J and replace nut D. III. ADJUSTING BACK GEARS: 1. Engage back gears using eccentric shaft lever K and allow mating gears to bottom. Then back off back gears until you feel a slight rock between mating gears and tighten set screw E. Tighten screw C so tension on bushing C is enough to hold gears in mesh on heavy cuts, but not so tight that the eccentric shaft lever K is hard to operate. Make final adjustment by allowing, lathe to run for a few minutes. If there is an abnormal amount of noise such as a gear rattling noise the gear clearance is too great, adjust by slightly unscrewing set screw E. If it seems to be a howling noise, the gear clearance is insufficient. Adjust by screwing in slightly set screw E. When proper gear clearance is obtained, lock set screw E with nut D. IV. OILING 1. Remove plug L and fill with teflon grease. Use CE1625 or equal.
4
PARTS LIST
5
ITEM NO. 1 2 3 4 5 6 7 8 9 10
PART NO. PT3R7NK1 114X220 PT2577K4 AS373KH2 PT1165RH1 PT257K1 AS441-3 183X103 PT523K2 *AS512K1
11 12 13 14 15 16
PT377NR1 139X26 112X1112 PT374NR1 PT1075NR1 *AS511K1
17 18 19 20 21 22 23 24 25 26 27 28 29 31 32
PT524K2 PT2676NK1 PT365K1 PT366K1 PT363K1 PT364K1 PT10K3 PT13NK1 PT1672NK1 112X228 PT24NK2 168x312 PT1151N1 PT378NK1 *AS361NK2 *AS202NK1
33 34 35 36 37 38 39 40 41 42 43 44 45
168X310 PT438NK1 PT382NK1 *AS25NK1 PT26NK1 PT207NK1 PT381NH1 *AS14NK1 PT367NR1 *AS15NK1 PT214NR2 *AS200K2 PT2090
PART NAME RUBBER PUMPER CAPSCREW COVER CAPILLARY OILER SCREW FLAT SPRING LURE CHART WASHER EXPANDER(SMALL) SMALL REARING (4-5-8-9-19-20) STOP SCREW NUT SCREW SPRING SHOE LARGE BEARING(45-8-17-21-22) EXPANDER(LARGE) OILER LAM. SHIM SOLID SHIM LAM. SHIM SOLID SHIM HEADSTOCK CLAMP WASHER CLAMP SCREW ORDER ITEM 32 TAPER PIN SCREW OIL HOLE WASHER BACK GEAR (29-30) Ecc. SHAFT(27-2833-34) TAPER PIN ORDER ITEM 32 SCREW TAKE-UP NUT(35-37 TAKE-UP WASHER THRUST BEARING OIL- PLUG SCREW CONE (39) SPRING BULL GEAR(41.43) PLUNGER SPINDLE (48) MORTON KEY
PARTS LIST HEADSTOCK PARTS
6
ITEM NO. 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 65 A 66 67 68 69 70 71 72 73 74 75 76
PART NO. CL2175NK (L205NK PT973K1 PT370K1 160X23 PT433NK1 *AS432NK2 CF 5L20 CF2401 PT2576NK1 112X248 PT2575K1 PT385NK1 138X27 137X29 PT28NK1 *AS229K1 PT27K32NK1 256X14 *AS635K2 PT2589NK1 139X25 *AS637NK1 PT2584K2 PT409T1 155x38 PT2584K1 162X35 PT2586K1 PT88NK2 160X10 *AS640K1
77 78 79 80 81 82 83 84 85 86 87 88
PT1501 121X16 122X106 PT1080NK1 132X1 *AS2583NK1 256X1 256X3 164X85 AXS635K2 130X103 PT383NR1
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34
*AS54K6R PT293NR2 PT206KR3 PT248KR3 PT249KR3 CE2401 PT201KR2 CE2653NK PT283NK1 PT2861NKI PT2677NR1 PT278NK1 PT1076NR1 122X104 168X106 AS285KR1 PT50K1 PT226K3 PT288NR1 PT52K2 *AS278K1 *AS53NK1 PT1480 PT1164-1 PT581K2 PT582K1 PT51K3 PT580K2 PT56NK2 143X216 160X18 160X255 160X48 PT3554NR1
PART NAME FACE PLATE SPINDLE SLEEVE KEY PROTECTING RING PIN V CONE PINION V CONE(39-50-1) V BELT CENTER CONE COVER SCREW U. D. HDSTOCK CLAMPING STUD NUT NUT REV. GEAR TWIN STUD (66-83) TWIN GEAR WICK REV. BRKT. (70-76) BUSHING NUT REV. SHAFT (60-85) LOCK BUSHING SNAP PIN OILER PIN SPRING BUSHING PLUNGER KNOB PIN REV. PLUNGER (71-72-73-74-75) PLUG SCREW SCREW SHOE DRIVE SCREW "CAUTION”PLATE (81) OIL WICK OIL WICK KEY REV. BRKT. ASSEM. DRIVE SCREW PIN TAILSTOCK PARTS LEVER (2-3-32) ORDER ITEM 1 ORDER ITEM 1 UPPER PLUG LOWER PLUG CENTER SPINDLE WRENCH NUT WASHER OILER SET-OVER SCREW BINDER SHOE SCREW TAPER PIN KEY T.S. TOP T. S. SCREW FELT WASHER T.S. NUT GRAD. DIAL (13-14) HANDWHEEL (15-23) HANDLE SCREW RETAINER (FRONT) FELT WIPER T. S. BASE RETAINER (REAR) T. S. CLAMP CLAMP BOLT PIN PIN PIN RUBBER WASHER
PARTS LIST
ITEM NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62
7
PART NO.
PART NAME
PT1481 *AS71NK1 168 x 108 PT70NK1 155 x 23 160 x 18 *AS76NK1 122 x 208 *AS87NK1 PT204JNK1 PT85NK2 256 x 3 AS228NK2 *AS231NK2 *AS225NK1 PT409NK1 PT83NK1 PT86NK1 PT80NK1 162 x 19 PT77NK1 PT352NK1 PT353NK1 *AS223NK2 PT349NK1 160 x 22 PT2677NR1 120 x 108 PT2854NK1 PT355NF1 168 x 210 160 x 10 *AS88NK2 *AS84NK1 162 x 35 PT89NK1 PT82NK1 PT1511 160 x 76 137 x 25 122 x 604 162 x 5 PT351NK1 PT97NK2 160 x 19 PT690NK1 *AS203NK1 PT208NK1 PT172NK1 *AS350NK1 *AS72NK1 PT357NKI PT412NK1 *AS227NK1 101 x 104 *AS76JNK1 PT204JNK1 AS228JNK1 122 x 606 162 x 34 AS74JNK1 PT70JNK1
Handle Handwheel (1,3,*7) Taper Pin Apron Oiler Pin Gear (6, 10) Screw Pinion (6,11) Order Item 7 Order Item 9 Felt Wick Stud Shaft (52) Pinion (16) Spring Shifter Gear Sleeve Spring Gear Shoes (Pair) Expanders (Pair) Screw (26, 30) Spring Pin Oiler Screw Oil Tube Screw Taper Pin Pin Knob (32,35,36) Lever (17,31*33) Spring Order Item 33 Knob Pipe Plug Pin Nut Screw Spring Pin Plunger Pin Key Worm (45,46,48) Collar Pin Screw (40) Half Nut (49) Spring Gasket Trough (53,55) Screw Gear (6,57) Order Item 56 Stud Screw Spring Cam Apron
PARTS LIST
*Available only as sub-assembly. Parts included are indicated by the item numbers appearing in parenthesis after part name.
8
ITEM NO
PART NO.
PART NAME
1 2 3 4 5 6 7 8 9
PT295R1 PT1480 160 x 17 *AS276NK1 *AS64NK1 122 x 103 PT1076NR1 PT63NK1 *AS224NK2
10
*ATA224NK2
11
*AS224JNK2
12
*ATA224JNK2
13
*AS485NK1
14 15 16 17 18 19 20 21 22 23 24
122 x 444 PT874NK1 PT66NK1 PT486NK1 107 x 6 PT244NK1 PT58NK1 PT57NK1 PT59NK1 122 x 102 *AS92NK2
25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45
PT211NK1 121 x 212 AS60NK2 PT210NK2 AS62NK2 112 x 114 PT3400 PT61NK1 PT358NK1 PT359NK1 *A665NK1 PT221NK1 CE2650NK PT233NK1 PT251NKI *CE2450NK PT209NK1 PT209NK2 *AS250NK3 PT252NK2 *AS90N1
46
*AS90K1
47 48 49 50 51 52
PT295NR1 PT1480 *AS277NR1 *AS110NK1 PT94NK1 *AS230NK2
53 54 55 56 57
PT257NK1 122 x 508 PT95NK1 PT91N1 PT91K1
Nut Handle Straight Pin Ball Crank (2) Collar (6,7) Screw Binder Shoe Bushing Cross Feed Scr. (1, *4,*5,8,*35) T.A.C.F. Screw (1,*4,*5,8, 16, 17) C. F. Screw (1,*4,*5,8,*35) T.A.C.F. Screw (1,*4,*5,8, 16,17) T. A. Base (14,15,25,26) Screw Gib Screw Cr. Feed Nut Screw Saddle Screw Retainer - R Retainer - L Felt Wiper Screw Base (14,25,26,36) Shoe Screw Saddle Lock Screw Lock Screw Washer Gib Pin Lock Screw C. F. Nut (33, 34) Gib Wrench T. P. Screw Ring Tool Post Assy. Block Block Tool Post (41 or 40) Wedge C.R. Top (*52, 14, 53, 56) C.R. Top (*52, 14, 53, 57) Nut Handle Crank (48) Collar (6,7) Bushing Screw (37, *49 150,51,55) Gib Screw C.R. Nut Swivel Swivel
PARTS LIST STANDARD GRADUATED COLLARS - EACH GRADUATION REPRESENTS A MOVEMENT OF THE CROSS SLIDE OF .001" OR A REDUCTION IN THE DIAMETER OF THE WORK OF .002" DIRECT READING GRADUATED COLLARS - EACH GRADUATION REPRESENTS A MOVEMENT OF THE CROSS SLIDE OF .0005" OR A REDUCTION IN THE DIAMETER OF THE WORK OF .001" 9" & 10-K COMPOUND REST TOP-LARGE DIA.(1 3/4")COLLAR STANDARD AND DIRECT READING GRADUATIONS FOR MODEL A. B, AND C
*AVAILABLE ONLY AS SUB ASSEMBLY. PARTS INCLUDED ARE INDICATED BY THE ITEM NUMBERS APPEARING IN PARENTHESIS AFTER PART NAME. ITEM NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14
SERIAL NUMBER OF LATHE AND UNIT CODE NUMBER MUST ACCOMPANY ORDER
PART NAME
PART
HANDLE RETAINING NUT PIN BALL CRANK (1) GRADUATED COLLAR (7-8-9) GRADUATED COLLAR (7-8-9) SHOE THUMB SCREW PIN COMP. REST BUSHING COMP. REST SCREW (2-3-*4-*5-10-20) COMP. REST SCREW (2-3-*4-*6-10-20) COMP. REST TOP (*11-17-18-19-21) COMP, REST TOP (*12-17-18-19-21)
PT1480 PT29SNR1 160X17 *AS277NR1
ITEM NO. 15 16
*AS110NR2
17 18 19 20 21 22
*AS1269NR1 PT1080NK1 PT1857 160X17 PT94NR2 *AS230NK3 *ASD230NK3 *ASL90N1 *ASD90N1
9
PART NAME COMP. REST TOP (*11-17-18-19-22) COMP. REST TOP (*12-17-18-19-22) COMP. REST GIB SCREW SCREW COMP. REST NUT COMP. REST SWIVEL COMP. REST SWIVEL
PART
*ASL90K1 *ASD90K1 PT2S7NKI 122X444 122X508 PT95NK1 PT91N1 PT91K1
PARTS LIST STANDARD GRADUATED COLLARS - EACH GRADUATION REPRESENTS A MOVEMENT OF THE CROSS SLIDE OF .001" OR A REDUCTION IN THE DIAMETER OF THE WORK OF .002”.
DIRECT READING GRADUATED COLLARS EACH GRADUATION REPRESENTS A MOVEMENT OF THE CROSS SLIDE OF .0005" OR A REDUCTION IN THE DIAMETER OF THE WORK OF .001".
SERIAL NUMBER OF LATHE AND UNIT CODE NUMBER MUST ACCOMPANY ORDER
9" & 10-K CROSS FEED SCREW-LARGE DIA.(1 3/4")COLLAR STANDARD AND DIRECT READING GRADUATIONS FOR MODEL A. B. AND C
ITEM
PART PART NAME
NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14
15
16
17
18
*AVAILABLE ONLY AS SUBASSEMBLY. PARTS INCLUDED ARE INDICATED BY THE ITEM NUMBERS APPEARING IN PARENTHESIS AFTER PART NAME.
STUD HANDLE RETAINING NUT PIN BALL CRANK (1-2) GRADUATED COLLAR (8-9-10) GRADUATED COLLAR (8-9-10) SHOE THUMB SCREW PIN C. F. SLEEVE BEARING CROSS FEED BUSHING CROSS FEED SCREW (3-4-*5-*6-11-12-13*19-23) CROSS FEED SCREW (3-4-*5-*6-11-12-1321-22-23) CROSS FEED SCREW (3-4-*5-*7-11-12-13*19-23) CROSS FEED SCREW (3-4-*5-*7-11-12-1321-22-23) PIN
ITEM NO. 19 20 21 22 23 24
NO. PT1241 PT1491 PT295NR1 160X17 *AS1264NK1 *AS64NK2 *AS1266NK2 PT1080NK1 PT1857 160X16 PT69R1 AS841R1 PT63NK
25
26
27
*AS224NK4
*ATA224NK4
*ASD224NK4
*ADTA224NK4 PT358NK1
10
PART NAME NO. CROSS FEED NUT (18-20) SCREW CROSS FEED NUT SCREW PIN CROSS FEED SCREW (3-4-*5-*6-11-12-13*19-23) CROSS FEED SCREW (3-4-*5-*6-11-12-1321-22-23) CROSS FEED SCREW (3-4-*5-*7-11-12-13*19-23) CROSS FEED SCREW (3-4-*5-*7-11-12-1321-22-23)
PART *AS65NK1 PT359NKI PT486NK1 PT66NK1 160X247
*AS224JNK4
*ATA224JNK4
*ASD224JNK4
*ADTA224JNK4
PARTS LIST GEAR BOX PARTS
*AVAILABLE ONLY AS SUBASSEMBLY. PARTS INCLUDED ARE INDICATED BY THE ITEM NUMBERS APPEARING IN PARENTHESIS AFTER PART NAME.
SERIAL NUMBER OF LATHE AND UNIT CODE NUMBER MUST ACCOMPANY ORDER
11
ITEM NO.
PART NO.
PART NAME
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32R
140 x 29 161 x 73 164 x 86 *AS603NK1 164 x 17 PT627NK1 160 x 17 *AS625NK1 PT626NK1 160 x 16 *AS619NK1 PT604NK1 168 x 108 *AS1541NK3 132 x 1 155 x 38 256 x 3 PT606NK2 160 x 31 AS604NK1 PT628NK1 PT601NK2 111 x 6 160 x 19 PT607NK1 PT1807 160 x 27 *AS88R2 PT607NR1 *AS605NK1 160 x 42 *AS400NK2
32L
*AS401NK1
33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58
PT384NK1 160 x 252 PT620NK1 256 x 1 PT621NK1 162 x 50 PT608NR1 PT624NK1 PT626NK1 160 x 16 *AS623NK1 PT626NK1 *AS622NK1 PT615K16NK1 168 x 310 PT615K18NK1 PT615K20NK1 PT615K22NK1 PT615K23NK1 PT615K24NK1 PT615K26NK1 PT615K28NK1 160 x 251 *AS614NK1 256 x 1 164 x 22
Nut Washer Key Shaft (1,2,3,5, 12, 13) Key Order Item 8 Straight Pin Camp Pinion (6,7) Order Item 11 Straight Pin Comp. Pinion (9, 10) Collar Taper Pin Index Pit. (15) Screw Oiler Felt Wick Bushing Straight Pin Gear Box Lead Scr. Gear Bushing Screw Pin Guide Bar Pin Pin Knob (27, 38, 39) Bushing Gear (33) Pin R.H. Tumbler (27 28,29, 30, 31,33, 38, 39) L.H. Tumbler (27 28,29, 30, 31,33, 38, 39) Bearing Shaft Shaft Felt Wick Gear Spring Plunger Gear Order Item 43 Pin Pinion Gear (40,42) Order Item 45 Pinion Gear (42,44) Cone Gear 16T Taper Pin Cone Gear 18T Cone Gear 20T Cone Gear 22T Cone Gear 23T Cone Gear 24T Cone Gear 26T Cone Gear 28T Pin Shaft (55,57,58) Wick Key
PARTS LIST
ITEM NO.
GEAR BOX PARTS PART PART NO. NAME PT32K20NK1 GEAR, 20 T. 140X29 NUT 161X21 WASHER PT33NK1 IDLER GEAR PT38NK1 BUSHING *AS31NK1 BRACKET (53) 114x228 SCREW *A3247NK1 BOLT (48-49) PT32K40NK1 GEAR, 40 T. PT32K56NK1 GEAR, 56 T. PT389NK3 GUARD PT1150NR SCREW STANDARD CHANGE GEAR PARTS PART PART NO. NAME
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27
140X29 161X21 AS336NK1 PT38NK1 *AS31NK1 *AS247NK1 AS36NKI 114X220 PT4NK1 AS1525NK3 AS1527JNR2 PT32KIGNK1 PT32K2411K PT32K32NK1 PT32K36NK1 PT32K40NK1 PT32K44NK1 PT32K46Nk1 PT32K48NK1 PT32K52NK1 PT32K54NK1 PT32K56NK1 PT32K60NK1 PT32K80NK1 PT33NK1 *AS32NK1 132X1
ITEM NO. 47 48 49 50 51 52 53 54 55 56 57 58
12
NUT WASHER COMP. GEAR 18/54T BUSHING BRACKET (8) BOLT (1-2) COMP. GEAR, 18/72T SCREW FRONT BRACKET INDEX PLATE INDEX PLATE CHANGE GEAR, 16T CHANGE GEAR, 24T CHANGE GEAR, 32T CHANGE GEAR, 36T CHANGE GEAR, 40T CHANGE GEAR, 44T CHANGE GEAR, 46T CHANGE GEAR, 48T CHANGE GEAR, 52T CHANGE GEAR, 54T CHANGE GEAR, 56T CHANGE GEAR, 60T CHANGE GEAR, 80T IDLER GEAR, 80T CHANGE GEARS SCREW
PARTS LIST TO MOUNT AND ADJUST 9" & 10K END GEAR GUARD
1. Install bracket on bed and secure in place. On horizontal lathes set bracket near end of bed. On underdrive lathes set bracket approximately 1/4" back from end of bed. Tighten setscrew A 2. Place eccentric in guard and mount in bracket with spacers between guard and bracket. (See fig. above) Use any combination of spacers required for proper clearance between spindle end and hole in guard. NOTE: Spacers of varied thicknesses are supplied for the purpose of using any combination to obtain proper installation. 3. Install one hex nut on end of hinge eccentric just enough to allow the second one to be installed. 4. Install second hex nut and lock with first. 5. Adjust the guard right or left by turning the eccentric by the locked nuts with a wrench. 6. Secure eccentric by tightening setscrew B 7. Unlock nuts and turn one up against bracket tight enough to keep guard closed but loose enough to swing open by hand. 8. Lock with second nut. NOTE: New machines have hinges tightened to keep guard closed during transit. necessary to loosen hex nuts slightly and relock to allow guard to open easier.
13
It may be
PARTS LIST
ITEM NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
PART NO.
PART NAME
PT145NK1 PT146N2 PT650NK2 PT906NK2 130 x 103 *AS1525NK2 *AS1527JNR1 *AS1529NR2 PT648K1 161 x 27 161 x 65 120 x 106 *AS147NK3 '*AS907NK3 118 x 214
Eccentric Guard Guard Guard Drive Screws Index Plate (5) Index Plate (5) Index Plate (5) Spacer Finished Washer Finished Washer Setscrew Bracket (12, 15) Bracket (12,15) Setscrew
NO. REQ. 1 1 1 1 4 1 1 1 1 1 2 1 1 1 1
14
ITEM NO. 16 17
PART NO.
PART NAME
139 x 31 *AS650NK2A
18
*AS650NK2B
19
*AS650NK2C
20
*AS146N2A
21
*AS146N2B
22
*AS146N2C
23
*AS906NK2
24
*AS441-3
Hex Nuts Guard Assembly (1,3,9,10,11,13,16) Guard Assembly (1,3,6,9,10,11,13,16) Guard Assembly (1,3,7,9,10,11,13,16) Guard Assembly (1,2,9,10,11,13,16) Guard Assembly (1,2,6,9,10,11,13,16) Guard Assembly (1,2,7,9,10,11,13,16) Guard Assembly (1,4,8,9, 10,11,14,16 Lubrication Plate (5)
NO. REQ 2
PARTS LIST
ITEM NO.
PART NO.
PART NAME
ITEM NO.
PART NO.
PART NAME
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
PT1945N1 170 x 206 170 x 206 AS1960N3 PT3658R1 155 x 38 PT1676NK1 AS735NR1 120 x 206 *AS103NK1 *AS431NK2 139 x 25 120 x 112 139 x 27 120 x 212
Lever Cotter Pin Cotter Pin Shaft & Pulley Oilite Bearing Oiler Washer Collar (9) Screw Cone (14,15) Cone (12,13) Hex Nut Screw Hex Nut Screw
16 17 18 19 20 21 22 23 24 25 26 27 28
139 x 27 PT1946N1 PT1948N1 PT395 N1 112 x 224 PT1949NK3 PT1946K1-G PT1373 PT243NR1 139 x 29 PT1944NT CE2323N *AS1940N3
Hex Nut R. H. Rod Turnbuckle L. H. Rod Hex. Capscrew Pin R. H. Rod Chip Guard Pivot Screw Hex Nut Base Belt 1-Ply Standard (6,5)
15
PARTS LIST 9" & 10K UNDERNEATH DRIVE UNIT Serial Number of Lathe and Unit Code Number MUST Accompany Order ITEM NO.
*AVAILABLE ONLY AS SUBASSEMBLY. PARTS INCLUDED ARE INDICATED BY THE ITEM NUMBERS APPEARING IN PARENTHESIS AFTER PART NAME.
16
PART NO.
PART NAME
1 2 3 4 5 6 7 8 8A 9 10 11 12 13
120X 206 PT2611NK PT2608N1 PT406K&FMI PT2609NKI 139X29 112X336 112X224 542X406 PT2640NKZ AS417NKI 120X106 160X116 *AS2605NKI
14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 28A 29 30 31 32 33 33A 33B 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55
PT390NK2 167X4 180X302 138X27 121X112 139X25 PT2603NKI 168X410 161X17 PT2604NKI *AS2607NK2 PT1824-3 161 X 21 PT36 58-1 PT2540NK3
SCREW COLLAR LOCK PIN KNOB HANDLE NUT BOLT BOLT BOLT CRADLE SUPPORT PLATE SCREW PIN SHAFT (11-12-20 21-22-23) PIVOT SCREW WASHER LOCK WASHER NUT SCREW NUT CRANK TAPER PIN WASHER RELEASE PIN BRACKET (25) PIN WASHER Oilite Bearing CRADLE
PT2638NTI 161X14 112X116 PT2600NKI AS2606NKI 120X6 PTI081NTI PT2601NKI PT1949NK2 AS735HRI PT1676NKI AS1960N3 112X232 155X44 PT2615NKI PT2614NKI *AS2613NKI 120X108 144 X I WAS103NKI 139X27 120X212
SPRING WASHER SCREW R. H. SCREW TURNBUCKLE(3334) SCREW SHOE L. H. SCREW CLEVIS PIN COLLAR WASHER SHAFT & PULLEY BOLT OILER PIN SPRING COLLAR (44) SCREW SCREW C.S. CONE(47-48) NUT SCREW
PT2608KI *AS43INKI 139X25 120X1112 170X206
COVER LOCK ROD C. S. CONE(53-54) NUT SCREW C. PIN
PARTS LIST
ITEM NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28
PART NO. PT4137K1 AS4128K1 *AS431NK2 120X112 139x25 CE3750K PT705K2 101 x 714 120 X 6 *AS4130K2 *AS4293K1 160x136 PT3660-1 PT167NK1 139 X 27 120X212 *AS103NK2 PT2042H1 CE790 AS4131K1 PT1855 *AS4120K4 PT1081NT1 120x1 PT403K& PT41214K2 160 x 148 *AS41372K2
29
112X116
PART NAME GUARD SHAFT & PULLEY V CONE (4-5) SCREW NUT FLAT BELT SCREW SCREW SCREW GEAR SEGMENT(9) BELT ROD FORK (12) PIN BUSHING WASHER SCREW CONE (15-16) SHAFT EXPANDER DRUM CONTROL COLLAR (23-24) THUMB SCREW FRAME (13-20-53)) SHOE SCREW BAKELITE BALL SWITCH LEVER PIN GEAR SEGMENT
17
ITEM 30 31 32
PART NO. 161X12 101 X 606 *AS4292K1
33 34 35 36 37
PT4291K1 PT1948N1 120 X 906 PT1853 *AS4127K2
38 39 40 41 42 43 44 45 45 47 48 49 50 51
139X29 PT390NK2 PT4136K1 PT4131K1 PT4123K2 120 x 1104 160x 111 PT4164K1 *AS4290K1 PT706K1 PT4135K1 PT4134K2 PT4121K1 PT4294K1
52 53
160X522 155x38
PART NAME WASHER SCREW FORK CONNECTOR (52) PELT ROD TURNBUCKLE SETSCREW THUMB SCREW ADJ. SCREW FORK (27-43) NUT SCREW SCREW PAD RUBBER PAD MOTOR HANGER SETSCREW SCREW PAD ADJ. SCREW (35) SCREW CAP SPRING BASE FELT TIGHTNER HANDLE PIN OILER
PARTS LIST headstock or drive unit by using these cord reinforced leather V-belts. Belts are skived for gluing and belt splicing cement is included.
BELTS AND LUBRICATION A TEXALON FLAT BELTS . A combination of textile and extruded nylon form a strong flexible belt recommended for use with Lathes. Able to withstand continual flexing without significant stretch and loss of efficiency. Texalon belts are skived on both ends and cement for joining skived ends is included with each belt. Type of Drive 9" HMD 10-KHMD 9" UMD 10 K UMD 10" UMD Bench 10" UMD Floor 13" UMD 4-Step
Cat. No. CE37ON CE3750K CE3752N CE3752K CE3753R CE3752R CE3752T
Type of Drive 13 UMD 3-Step 14 1/2" UMD 4-Step 14 ½ UMD 3-Step 16" UMD 4-Step 16" UMD 3 Step 16-24" UMD 4-Step 16-24" UMD 3-Step 16" Turret
Cat. No. CE3753T CE3752F CE3753F CE3752H CE3753H CE3752V CE3753V CE3753H
Cat. No. CESL61L CESL62L CE5L54L CE5L51L
CE1898 CE1899
1 ¾” 3"
Thickness ½” ½”
Skive Length 6 3/8” 6 3/8”
Ship. Wt. 1 lb. 1 lb. 1 lb. 1 lb.
Rubber V-Belts Rubber V-Belts for use with Lathes and other power driven machinery. Specify catalog number, maximum width, and outside circumference when ordering. Catalog Number
Outside Length
Catalog Number
Outside Length
V-Belts with 3/8” Top Width CE3L210 CE3L220 CE3L230
21” 22” 23”
CE3L240 CE3L260 CE3L270
24” 26” 27”
V-Bets with ½” Top Width CE4L208 CE4L290 CE4L300 CE4L310 CE4L320 CE4L440 CE4L450 CE4L460 CE4L470
28” 29” 30” 31” 32” 44” 45” 46” 47”
CE4L480 CE4L490 CE4L530 CE4L540 CE4L580 CE4L800 CE4L640 CE4L700 CE4L800
48” 49” 53” 54” 58” 60” 64” 70” 80”
V-Belts with 5/8” Top Width CE5L380 CE5L400 CE5L410 CE5L420 CE5L430 CE5L440 CE5L450
Maximum Size of Belt Width
Drive U M.D. U.M D. H.M.D. H.M.D.
NOT PEMISSABLE TO SHIP BY ANY OF THE AIR SERVICES
B TEXALON BELT CEMENT for bonding skived ends of Texalon Belts. CE1887. Texalon Belt Cement 1/4 oz. bottle CE2323N. Oak tan single ply flat leather bell without cord reinforcing for 9" Horizontal Motor Drive only. Ho square ends and lace for joining. C BELT SPLICING CLAMPS . For gluing skived ends of cone pulley belts or other flat leather belts. Made of heavy steel plate with guide for aligning edges of belt ends Catalog Number
Size Lathe 9" 10-K 9" 10-K
36” 40” 41” 42” 43” 44” 45”
Ship. Wt.
CESL480 CESL470 CESL490 CESL500 CESL510 CESL520 CESL550
46” 47” 49” 50” 51” 52” 55”
Chuck Wrenches Catalog Number CE2748 CE2742 CE2743 CE2749 CE2744 CE2746
4 lbs. 5 lbs.
D LUBRICATING OIL . Nothing is more important to the satisfactory operation and life of fine machinery than correct lubrication. The lubricating oils listed below have been thoroughly tested in our research laboratory and are highly recommended. It is essential that the correct type of oil be used for the lathe spindle and latche apron oil reservoirs and general lubrication. A supply of each kind of oil should be kept on hand and used as needed. The Saybolt viscosity of the various oils is indicated in seconds at 100°F.
Size Square .277” .297” .375” .400” .420” .570”
Shipping Weight 2 lb. 1 lb. 2 lbs. 2 lbs. 2 lbs. 2 lbs.
Sizes of Wrenches Required for Various Sizes of Chucks Cat. No. of Chuck CL4006NK CL4206NK CL4006R CL4206R CL4207R CL4006L CL4206LQ CL4207LQ CL42090 CL4207MH CL4209MH CL4210MH CL4212H CL3005NK CL3505NK CL3506NK CL3005R CL3505R CL3506R CL3005L CL3505LQ CL3506LQ CL3507Q CL3505MH CL3506MH CL3507MH CL3509MH.
Cat No.
Viscosity Quantity Ship. Wt. General Lubricating Oil (See Oil Chart For Individual Machine) 240-500 1 quart 3 lbs. CE1603 240-500 12 quarts 31 lbs. CE1906 240-500 Gal. can 11 lbs. CE2019 Oil for Spindle Bearings of Lathes (For other components tee Oil Chart for Individual Machine) 100 1 quart 3 lbs. CE1600 100 12 quarts 31 lbs CE1905 100 Gal. can 11 lbs. CE2017 Oil for Lathes (See Oil Chart for Individual Machine) 150-240 1 quart 3 lbs. CE1602 150-240 12 quart 3 Ibs. CE1904 150-240 Gal can 11 Ibs. CE2018
LEATHER V-BELTS FOR CONE PULLEYS Lathe cone pulley V-belts can be replaced without disassembling the lathe 18
Size of Chuck 6” 6” 6” 6” 7 ½” 6” 6” 9” 7 ½” 9” 10” 12” 5” 5’ 6” 5” 5” 6” 5” 5” 6” 7 ½” 5” 6” 7 ½” 9”
Type of Chuck Independent Independent Independent Independent Independent Independent Independent Independent Independent Independent Independent Independent Independent Universal Universal Universal Universal Universal Universal Universal Universal Universal Universal Universal universal Universal Universal
Size Square .297” .297” .297” .297” .420” .297” .297” .420” 420” .420” .420” .420” .420” .277” .375” .400” 277” .375” .400” .277” .375” .400” 400” .375” .400” .400” .570”
Cat. No. of Required Wrench CE2742 CE2742 CE2742 CE2742 CE2744 CE2742 CE2742 CE2744 CE2744 CE2744 CE2744 CE2744 CE2744 CE2748 CE2743 CE2749 CE2748 CE2743 CE2749 CE2748 CE2743 CE2749 CE2749 CE2743 CE2749 CE2749 CE2746
PARTS LIST MOTOR PULLEYS
Part No.
A
PT2101NR1 PT2106NR1 PT2111NR1 PT2116NR1
.635 .635 .635 .635
PT2131NR1 PT2181NR1 PT2183NR1 PT2131K1 PT2136K1 PT2185NK1 PT2187NK1 PT2136NR1 PT2138NR1 PT2127R1 PT2129R1 PT2156R1 PT2158R1
.635 .635 .635 .635 .635 .635 .635 .635 .635 .635 .635 .635 .635
B STYLE 1 2- 3/32 2-15/32 3 3-45/64 STYLE 2A 3.408 3.570 3.570 3.956 4- 3/16 4- 3/16 4- 3/16 4- 3/16 4- 3/16 4-19/32 4-19/32 5- 5/16 5- 5/16
BB
C 5/8 5/8 5/8 5/8
2.093 2.093 2.093 2.237 2-43/64 2-23/32 2-23/32 2.822 2.822 3- 5/32 3- 5/32 2- 3/32 2- 3/32
5/8 5/8 7/8 5/8 5/8 5/8 7/8 5/8 7/8 5/8 7/8 5/8 7/8
19
Part No.
A
PT2101T1 PT2103T1 PT2106T1 PT2108T1 PT2127T1 PT2129T1
.490 .490 .490 .490 .490 .490
PT2101F1 PT2106F1
.490 .490
PT2101HI PT2102H1 PT2101FH2 PT2103FHI PT2106FH2 PT2108FH1 PT2161HI PT2163H1 PT2189H1 PT2191H1 PT2127F1 PT2129F1 PT2166FH1 PT2168FH1 PT2127H1 PT2129H1
.490 .490 .490 .490 .490 .490 .490 .490 .490 .490 .490 .490 .490 .490 .490 .490
B STYLE 2 2-17/32 2-17/32 2-63/64 2-63/64 4-21/64 4-21/64 STYLE 3 2-17/32 2-63/64 STYLE 4 2- 1/8 2- 1/8 2-17/32 2-17/32 2-63/64 2-63/64 3- 9/64 3- 9/64 3-13/64 3-13/64 3- 9/16 3- 9/16 3-49/64 3-49/64 4- 5/64 4- 5/64
C 7/8 1-1/8 7/8 1-1/8 7/8 1-1/8 7/8 7/8 7/8 1 7/8 1-1/8 7/8 1-1/8 7/8 1-1/8 7/8 1-1/8 7/8 1-1/8 7/8 1-1/8 7/8 1-1/8
PARTS LIST 10-K HANDWHEEL COLLET ATT. MODEL A, B & C
ITEM NO. 1 2 3 4
PART NO.
PART NAME
AS798K1 PT794K1 PT793K1 *AS793K1
HANDWHEEL DRAW BAR SLEEVE DRAW BAR DRAW BAR(1-2-3)
10-K HANDLEVER COLLET ATT. OLD STYLE MODEL A, B & C
1 2 3 4 5 6 7 8 9 9A 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27
PT978K1 *AS988NK1 PT986K1 PT983NK1 PT975K1 PT981K1 PT488K1 172X20 PT979K1 160X58 PT995NKI CE2734 PT490NH1 256X11 PT1823 PT984NH1 162X2 PT489NH1 PT409R1 PT991NK1 PT492NR&T1 PT494NR&T1 155X5 PT991NK1 PT377NR1 PT1058NR1 PT993NK2 PT997NK1
ADJUSTING NUT YOKE SECTOR (13) YOKE CONE SNAP RING DRAW BAR COLLAR' BALL RETAINER CAM BALL SLEEVE PIN KNOCK-OUT NUT SPANNER WRENCH STOP NUT SCREW WICK PIN SHOE SPRING SCREW SNAP RING YOKE LEVER SCREW-WITH HOLE YOKE NUT OILER YOKE BOLT SCREW NUT YOKE BRACKET BRACKET STUD
10-K HANDLEVER COLLET ATT. NEW STYLE MODEL A, B & C
1 2 3 4 5 6 7 9 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 23 30 31 32 33
PT4809RH1 120X903 CE2392 126x503 PT1078RH1 PTIl59-1 *AS989NK1 256x11 P1986K2 PT1823 PT983NK1 PT975K2 PT981K1 PT488K1 172x20 PT979K2 160x58 PT409R1 *AS978K2 *AS998K1 PT995NK1 CE2734
SHOE SETSCREW WRENCH SETSCREW SHOE PIN YOKE SEGMENT(B) FELT WICKS CLUTCH YOKE CONE PIN CONE SNAP RING DRAW BAR COLLAR BALL RETAINER STEEL BALL CLUTCH SLEEVE SPINDLE PIN SPRING CL. STOP NUT(I-2 LOCK COLLAR(4-5) KNOCK-OUT NUT SPANNER WRENCH
155x5 PT494NR&T1 PT492NR&T1 PT990NK1 PT377NR1 PT1058NR1 PT991NK1 PT993NK2 PT997NK1
OILER YOKE LEVER NUT YOKE LEVER SCREW YOKE LEVER SCREW JAM NUT YOKE BOLT YOKE BRACKET BRACKET STUD
*AVAILABLE ONLY AS SUBASSEMBLY PARTS INCLUDED ARE INDICATED BY THE ITEM NUMBERS APPEARING IN PARENTHESIS AFTER PART NAME. 20
PARTS LIST 9" HANDWHEEL COLLET ATT. MODEL A, B & C
9" HANDLEVER COLLET ATT. OLD STYLE MODEL A, B & C
9" HANDLEVER COLLET ATT. NEW STYLE MODEL A, B & C
21
ITEM NO. 1 2 3 4 5
PART NO. AS793N4 PT995NK CE2734 *AS795N1 PT493NH1
PART NAME DRAW BAR ASM. KNOCK-OUT NUT SPANNER WRENCH SLEEVE (5) KEY
1 2 3 4 5 6 7 8 9 10 11
PT978N1 *AS988NK1
ADJUSTING NUT YOKE SECTOR (15)
PT986N3 PT983MK1 PT975N2 PT981N2 PT488N2 172x20 PT979N3 *AS979N3
12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32
PT995NK1 CE2734 PT490NH1 256x11 PT1823 PT9B4NH1 162x52 PT489NH1 160X58 PT976N1 *AS795N1 PT493NH1 PT990NK1 PT492NR&T1 PT494NR&T1 155x5 PT991NK1 PT377NR1 PT1058NR1 PT993NK2 PT997K1
Order Item II SNAP RING DRAW BAR COLLAR BALL RETAINER CAM BALL SLEEVE SLEEVE(4-5-7-8-9 16-17-18-19-21) KNOCK-OUT NUT SPANNER WRENCH STOP NUT SCREW WICK PIN SHOE SPRING SCREW PIN SNAP RING SLEEVE (23) KEY YOKE LEVER SCREW, WITH HOLE YOKE NUT OILER YOKE BOLT SCREW NUT YOKE BRACKET BRACKET STUD
1 2 3 4 5 6 7 9 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33
PT4809RH1 120x903 CE2392 126 x503 PT1078RH1 PT1859-1 *AS988NK1 256x11 PT986N4 PT1823 PT983NK1 PT975N3 PT981N2 PT488N2 172x20 PT979N4 160x58 PT976N1 *AS97BN2 *AS998N1 PT995NK1 CE2734 PT493NH1 *AS795N1 155x5 PT494NR&T1 PT492NR&T1 PT990NK1 PT377NR1 PT1058NR1 PT991NK1 PT993NK2 PT997NK1
SHOE SETSCREW WRENCH SETSCREW SHOE PIN YOKE SEGMENT(8) FELT WICKS CLUTCH YOKE CONE PIN CONE SNAP RING DRAW BAR COLLAR BALL RETAINER STEEL BALL CLUTCH SLEEVE SPINDLE PIN BAR SNAP RING CL. STOP NUT(1-2) LOCK COLLAR(4-5) KNOCK-OUT NUT SPANNER WRENCH KEY SLEEVE (23) OILER YOKE LEVER NUT YOKE LEVER SCREW YOKE LEVER SCREW JAM NUT YOKE BOLT YOKE BRACKET BRACKET STUD
PARTS LIST 9" & 10-K ACCESSORIES
22
PARTS LIST 9" & 10-K MICROMETER CARRIAGE STOP ITEM NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17
PART NAME CAPSCREW FELT WASHER BUSHING PHILLIP SCREW COVER PLATE MICROMETER STOP FRAME ORDER ITEM 13 SETSCREW CLAMP (8 10) JAM NUT SHOE LOCK SCREW SHAFT (7) English FELT WASHER -- SLOTTED KEY Shaft (17) Metric Order Item 16
9" & 10-K COLLET RACK
PART NO.
ITEM NO 1 1A 2 3 4 5 6 7 8 9 10
114 x 124 PT1207NT1 PT1206NT1 104 x 206 PT1209NT1 PT1203NT2 122 x 520 AAS1201NK1 137 x 23 PT1083NT1 PT1204NT2 *AS1202NK2 PT1208NT1 PT1210NH1 PT2271NK1
PART NAME COLLET RACK COLLET RACK RACK PIPE COLLAR SCREW BRACKET (3-*5-9) CLAMP (6-7) SETSCREW JAM NUT SETSCREW SQUARE HD. SETSCREW DRAW BAR HOOK
PART NO. P-780N2 PT780KR2 PT497NK1 PT371NK1 *AS782NK1 *AS863NR1 122 x 624 137 x 25 122 x 505 118 x 108 PT781NR & T1
9" & 10-K PLAIN CARRIAGE STOP 9" & 10K THREAD DIAL ITEM NO.
PART NAME
PART NO.
1 2 3 4 5 6 7 8 9 10 11 12
OILER INDICATOR DIAL (3-4) SETSCREW SHOE INDICATOR SHAFT WRENCH SETSCREW INDICATOR FRAME MOUNTING STUD WORM WHEEL (11) SETSCREW SETSCREW
155 X 16 *AS888NK2 122 x 903 PT1078NK1 PT891NK2 CE2392 120 x 6
ITEM NO. 1 2 3 4 5 6
PT889NK1 *A887NR2 120 x 6 120 X 6
9" & 10-K THREAD CUTTING STOP ITEM 1 2 3 4
PART NAME SCREW CUTTING STOP BINDER PLUG SETSCREW
PART NO. PT245NR1 PT67NK1 PT418NK1 122 x 606
23
PART NAME Collar. Screw Stop Clamp Setscrew Hex Nut Complete Unit
PART NO. PT210NK2 PT1489NK1 PT1201NK1 122 x 520 137 x 23 CL758NK1
PARTS LIST
ITEM NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35
PART NAME
BAKELITE BALL SETSCREW CLAMPING LEVER OILER TURRET CLAMP SETSCREW ADJ. NUT (6) STUD GUIDE WRENCH CAPSCREW WASHER TURRET BINDER (10-11) HEX. TURRET(12-15-16. 18-19-20) DOWEL INDEX BUSHING NOTE: CUSTOMERS ORDER FOR THIS PART MUST BE ACCOMPANIED WITH UNIT CODE NUMBER. TURRET PLUG (17) PIN SETSCREW TURRET GEAR INDEXING PIN SPRING WASHER WOODRUFF KEY TURRET STUD TURRET RAM PIVOT PIN OILER SWIVEL (2q-.30) NEEDLE REARING SWIVEL STUD OILER INDEX SHAFT PIN SETSCREW SHOE
PART NO. PT3131NR1 122x510 PT3006NR1 155X38 PT3003NR1 114x710 *AS3009NR1 PT3130NR2 CE2657 PT2901NT1 PT3037NR1 *AS3010NR1 AS3002NR2 153x16 PT3013NR2
*AS3129NR1 160x21 120X105 PT3023NR2 PT477NR2 162 X 16 161 x 26 PT2070 PT3008NR1 PT3001NR3 PT3019NR1 155x16 *AS3119NR2 PT3134NR1 PT3173NR2 155 X 17 PT3030NR1 160 X 25 126x505 PT1081NT1
24
ITEM NO. 36 37 38 39 40 41 42 43 44
45 46 47 48 49 50 51 52 53 54 55 56
PART NAME
END PLATE NUT STOP SCREW HANDLEVER LOCK BOLT BUSHING SETSCREW LOCK BOLT LEVER(4748-49) SPRING LOCK BOLT(40-45) NOTE: CUSTOMERS ORDER FOR THIS PART MUST BE ACCOMPANIED WITH UNIT CODE NUMBER. SPRING SPRING RETAINER COTTER PIN PIN ROLLER TAPER PIN STOP SCREW GEAR (32-50) TAPER PIN STOP SCREW INDEX(3233-34-35-36-37-51) WRENCH HANDLE CAPSCREW
PART NO. PT3005NR1 139x23 PT3029NR1 PT3121NR1 PT3012NR1 120x1006 *AS3016NR1 162x34 *AS3011NR3
PT3014NR3 PT3015NR2 170x103 PT3018NR2 PT3017NR1 168X6 *AS3024NR1 168x5 *AS3004NR1 CE2392 PT3122NR1 114x616
PARTS LIST
ITEM
PART PART NAME
NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33
ITEM NO.
NO. PIN SIDE GIB (1) HORIZ. GIB (5) HORIZ. GIB SCREW OILER ROUND FELT LOCK BOLT CAM PIN SPRING LEVER PIN INDEXING LEVER (10-12-13) TAPER PIN PIN PIN CAM PIVOT PIN HINGE STUD NEEDLE BEARING OILER PIN CAPSCREW SWIVEL HINGE(16-17-18) H. L. BRACKET TURRET BASE FOR 9”MODEL A. B. & C TURRET BASE FOR 9' REG. 1 1/16 R 1' COL. TURRET BASE FOR LIGHT 10, MODEL A. B. & C TURRET BASE FOR 10' 13'-11/16' & 1' COL.
160X18 *AS3036NR1 *AS3035NR1 111X110 155X38 256x8 PT3020NR1 160x48 PT3021NR1 PT3027NR1
FRONT CONE FRONT CONE
PT3127NR1 PT3127T1
CONE BEARING-FRONT (35)
*AS3125NR1
34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54
AS302rNR2 168 X 5 160 x21 160 x 48 PT3022NR1 PT3124NR1 PT384NK1 155x16 160X52 114x114 AS3120NR1 PT3118NR1 PT3000N1 PT3000S1C PT3000K1 PT3000R1
25
PART NAME
PART NO.
CONE BEARING. FRONT(36 PIN PIN BASE CLAMP BASE CLAMP BASE CLAMP CONE BEARING-REAR CONE BEARING-REAR HEX. NUT SETSCREW SPRING WRENCH CAPSCREW REAR CONE REAR CONE
AS3125T1 160x16 160X50 PT3139NK2 PT3139R2 PT3139T1 PT3137NR1 PT3137T1 138x18 125x112 PT3028NR1 CE2391 114X124 PT3126NR2 PT3126T2
WRENCH CAPSCREW CAPSCREW ADAPTER BASE
CE2658 114x124 114x340 PT3135T1
PARTS LIST H. L. DOUBLE TOOL CROSS SLIDE FOR 9", 10-K, 10" REG.
26
PARTS LIST ITEM NO. 1 2 3 4 4A 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 22A 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49
PART NAME
WRENCH HOL. HD. CAPSCREW SETSCREW FRONT TOOL BLOCK FRONT TOOL BLOCK ASSEM. (2-3-5-6-7-8.9-17) PIN STUD SCREW BLOCK GIB - LEFT STUD SCREW NUT BLOCK Gib - RIGHT SETSCREW COLLAR GEAR RETAINER CAPSCREW SHAFT LEVER BAKELITE BALL WRENCH TEE SLOT NUT OILER SETSCREW PIN HOL. HD. CAPSCREW REAR TOOL BLOCK REAR TOOL BLOCK ASSEM. (3-5 6.8-9-17-21) OIL PLUG BASE NUT BUSH1NG CAPSCREW STOP PINION SEGMENT SEGMENT SHAFT (10-11-31 TAPER PIN LOCK PIN SETSCREW BASE GIB SETSCREW RACK CAPSCREW RACK SUPPORT (36 37 39-40) MACH1NE SCREW PIN BUSH1NG WRENCH C. F. NUT ENGLISH (32-33) C. F. NUT METRIC (32-33) CH1P GUARD (46) SCREW WASHER CAPSCREW WRENCH
9" PART NO
10-K PART NO
10" REG PART NO
CE2389 11 4x244 121xl16 PT812NR2
CE2389 114x252 121x116 PT812K1
CE2389 114X244 121x116 PT812NR2
*AS812NR2 160x21 PTS17NR1 PT449NR1 PT818NR1 PT448NR1 121x5 PT453NR1 PT824NK1 114x216 PTB08NR1 PT406K & FH1 CE2385 PT74INR2 155x17 122x706 160x240 114x252 PT813NR2
*AS812 I 160X21 PT817NR1 PT449NR1 PTBIBNR1 PT448NR1 121x5 PT453NR1 PT824NK1 114x216 PT808NR1 PT406K & FH1 CE2385 PT741NR2 155X17 122x706 160240 114x256 PT813K1
*AS812 NR2 160x21 PT817NR1 PT449NR1 PTBIBNR1 PT448NR1 121x5 PT453NR1 PT824R1 114x216 PT808NR1 PT406K & PH1 CE2385 PT741NR2 155X17 122x706 160x240 114x252 PT813NR2
AS8 I 3NR2 PT823NH1 PT800NK3 PTBI1NH1 PT81ONH1 114xl10 PT809NK1 PT805NK1
*AS813K1I PT823NH1 PT800NK3 PT81INH1 PTBIONH1 114x110 PT809NK1 PT8OSNK1
*AS8 13NR2 PT823NH1 PT800NK3 PT811H1 PT810H1 114x1 10 PT809R1 PTB05R1
* AS807N R 168x210 PT358NK1 PT359NK 1 PT80INK1 122x444 PT82ONK1 114x216
* AS07N R1 168x210 PT358NK1 PT359NK1 PTR80NK1 122x444 PT82ONK1 114x216
AS807NR1 168x210 PT358NK1 PT359NK1 PT8OIRI 122x513 PT82ORI 114x216
*AS804NK1 103x106
AS804NK1 103x106
*AS804R1 103x107
PT814NK1 CE2739
PT814NK CE2739 ....
PT814R1
*AS799NR1
*AS799NR1
* AS799NR1
*AS2252NR1 *AS821NK2 1I0x106 161x11 112x116 CE2387
'AS2252NR1 *AS821NK2 1OIXI06 161xl1 112x116 CE2387
'AS2252NR1 *AS821R2 101X106 161xilI 112xl16 - -.-
h AVAILABLE ONLY AS SUBASSEMBLY. PARTS INCLUDED ARE INDICATED BY THE ITEM NUMBERS APP EARING IN PARENTHESIS AFTER PART NAME. SERIAL NUMBER OF LATHE AND UNIT CODE NUMBER MUST ACCOMPANY ORDER
27
PARTS LIST 27 THREADS PER INCH It is possible to NUT 27 threads per inch on any Lathe by procuring an additional gear. 9" and Light Ten Models B & C Lathes and 10"-1"Collet Lathes with wide range gear box are already equipped to nut 27 threads. For other Lathes see list below:
SIZE AND TYPE OF LATHE
PART NO.
DOUBLE TUMIBLER GEAR BOXES 9" & Lt. 10AA, Model A, Double Tumbler
PT32K42NK1
10" (11/16 or 1" Col. Cap.) Double Tumbler
PT32K42R1
13" Double tumbler .
PFT612K32T1
14'", 16" 16-24" & 2H Double Tumbler For Gear Box Code No. Q.C.G. 103...
PT612K32F52
For Gear Box Code No. D. T.';. 104...
PT612K32FH3
SINGLE TUMBLER GEAR BOXES 10" (11/16 or 1" Col. Cap.) Single Tumbler
PT612K32R1
13" Single Tumbler .
PT612K24T1
145", 16', 16-24" & 2H Single Tumbler
PT612K24FH1
SEE REVERSE SIDE FOR SET-UP CHART
IMPORTANT. When ordering you must specify "Gear is to be used to cut 27 threads per inch." Also state serial number of your lathe wH1ch is stamped on flat way of bed at tailstock end and gear box code number stamped on face of tumbler guide bar attached to bottom of gear box. This informaT1on enables us to doublecheck and to determine if correct gear is being ordered.
28
PARTS LIST
SET-UP CHART FOR CUTTING 27 THREADS PER INCH DOUBLE TUMBLER GEAR BOX 9" & Lt. 10 requires 20 Tooth Gear. Furnished With Lathe 10' (1' Col.) requires 20 Tooth Gear. Furnished With Lathe 13" requires 32 Tooth Special Gear, PT612K32T1 14'", 16", 16-24" & 2H requires 32 Tooth Special Gear. Use PT612K32FH2 Gear on lathes with Gear Box Code QCG103. For lathes with Gear Box Code DTG104 use PT612K32FH3 Gear Stud Gear
See Note Above
Left Hand Tumbler A A B C D E
Threads per Inch
27
9' & Lt. 10 requires 42 Tooth Special Gear, PT32K421,TYl 10"(1" Col.) requires 42 Tooth Special Gear, PT32K42R1 13" requires 64 Tooth Gear. Furnished On Lathe 14 ½ ", 16", 16-24 and 2H requires 64 Tooth Gear. Furnished On Lathe
SINGLE TUMBLER GEAR BOX 10" Lathe requires 32 Tooth Special Gear, PT612K32R1 13" Lathe requires 24 Tooth Special Gear, PT612K2LT1 14-", 16", 16-24 and 2H Lathes requires 24 Tooth Special Gear, PT6L2K24FH1
Sliding Gear In
Out
Top Lever Left Center Right Left Center Right
29
Threads Per Inch
27
PARTS LIST
ITEM NO.
PART NAME
10" PART NO
13" PART NO
14 ½ PART NO
104 . 206 PT1209NT1 PT1206NT1 PT1207NT1
104 x 206 PT1209NT1 PT1206NT1 PT1207NT1
104 x 206 PT1209FH1 PT1206FH1 PT1207FH1
114 x 236 CE2389 PT1083NT1 PT1204NT2 PT1202RT1 PT2271RT1 PT1208NT1 PT1203NT2 PT2270NT1 PT121 IRT1 137 x 25 PT12I0NH1 PT1201R2 114 n 228 114x6 PT1121RI
114 x 236
114 .444
114 x 444
PT1O83NT1 PT1204NT2 PT1202RT1 PT2271RT1 PT1208NT1 PT1203NT2 PT2270NT1 PT1 21IRT1 137 x 25 PT1210NH1 PT1201T2 114 X 22B 114x6 PT1212RI
PT1083FH1 PT1204FH2 PT1202FH2 PT2271FH1 PT1208FH1 PT1203FH2 PT2270FH1 PT121 IFH1 137 x 25 PT1210NH1 PT1201FH2
PT1083FH1 PT1204FH2 PT11202FH2 PT2271FH1 PT1208FH1 PT1203FH2 PT2270FH1 PT121 IFH1 137 x25 PT1210NH1 PT 1201FH2
. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21
PH1LLIPS SCREW COVER PLATE BUSH1NG FELT WASHER MICRO STOP FRAME CAPSCREW HEX. WRENCH SHOE LOCK SCREW MICRO SHAFT (ENGLISH) MICRO SHAFT (METRIC) FELT WASHER (SLOTTED) MICRO STOP DIAL (ENGLISH) MICRO STOP DIAL (METRIC) CLAMP SCREW JAM NUT KEY CLAMP CAPSCREW CAPSCREW BED MOUNT1NG BRACKET
30
16”, 16/24 & 17” SERIAL NUMBER PART NO OF LATHE AND UNIT CODE 104 x 206 NUMBER MUST PT1209FH1 ACCOMPANY PT1206FH1 ORDER PT1207FH1
PARTS LIST
BALL BEARING LIVE CENTERS
ITEM NO. 1 2 3 4 5 6 7 8 9 10
9" & 10" PART NO. PT3276NR1 PT3281NR1 PT3277NR1 PT502NH1 PT3275NR1 155 x 17 ----------------PT3278NR2 PT3279NR1 120 x 1104
13", 14 1/2" & 16" PART NO. PT3276TH1 PT3281TH1 PT3277TH1 PT3280TH1 PT3275TH1 155 x 17 120 x 904 PT3278TH2 PT3274TH 1 120 x 1104
PART NAME
SPINDLE POINT SPINDLE HOLLOW PROTECT1NG COLLAR BALL BEARING BODY OILER SETSCREW REAR BUSH1NG TAKE-UP NUT S CTSCRFE
LUBRICATION Use CE1602 Machine Oil or equal. No. 2 M. T. Center Bearings are sealed but No. 3 :MT. Center Bearings are not: therefore should be periodically repacked with grease. ADJUSTMENT Screw Take-up NUT B tight so Spindle can hardly be turned by hand. Back up fracT1on of a turn so the Spindle will just barely turn freely. Proper tension isimportant. Cannot be too tight or loose. Lock the setscrew A snug, but not too tight. TO DISASSEMBLE Loosen setscrew A and remove Take-up NUT B . Drive out Spindle C along with bearing D and collar E with a punch through.; the two holes as shown at G . (Drive out with two set screws on No. 3 ,:.T.) If necessary to remove rear bushing H drive out by inserting bar into front end of body. Bar diameter must be just slightly under hole size of Body. TO ASSEMBLE Flush center of body with mineral spirits or equal before assembling. Drive in rear bushing, if it has been removed. Place Spindle into Body, tapping lightly on outer bearing race if necessary. Press on protective collar. 31
CUTTING TOOLS DATA
32
INSTRUCTIONS ON USE OF CUTTER BIT GRINDING BLOCK Suggested CNUTT1ng Off Tool grinding angles a illustrated re given as general informaT1on only, m cutting off tools CANNOT be ground In the Universal cutter Bit Grinding Block.
1.
cutter bit in proper sleeve and tighten securely, allowing approximately of the cutter bit to protrude from the nose of the sleeve.
2.
Place sleeve in block, set cutter bit to desired angle (graduations on sleeve are In Increments of 50) and lock In position with set screw on top of block. Reset for top and side clearance angles, if desired.
3.
Due to the many variations that enter into correct grinding angles such as: cutting peed, type of finish and kind of material to be macH1ned with cutter bit, no attempt has been made to show these angles in the instructions, however, suggested clearances are charted on the reverse side of this sheet. This is for the average type of work and may not agree with the various other publicaT1ons on cutter bit grinding. Note: If tool rest on your grinder is not large enough to accommodate cutter Bit Grinding Block, clamp an auxiliary plate to extend the tool rest.
1. Heel the block as shown for grinding all clearances. Unless a small degree of front clearance is required then lay on flat of block.
2. Use both sides of wheel for grinding side clearances on all shapes of tools. Angle block to get proper shape.
3. Use sides of wheel for grinding back and side rake. Angle block to get proper top back rake. Heel block if dosired.
Item No. 1 2 3 4 5 6 7 8
4. Use face of wheel for grinding radius, on round nose tools, rotaT1ng the block to develope the proper radius. Heel the block as shown in Fig. 1.
Part Name Hex Wrench Setscrew Block (2) Setscrew Sleeve (4) For Sleeve (4) For Sleeve (4) For Sleeve (4) For
Part No.
173x6 149xS05 *AS4635-1 126x503 316" Bit *A5636 1/4" Bit *AS4637-1 5/16" Bit *AS4638-1 3/8" Bit *A54639-1
Available only as sub-assembly. Parts included are indicated by the item numbers appearing in parenthesis after part name.
33
PARTS LIST HOW TO USE YOUR 10-IN-1 TOOL BLOCK The Ten-in-One Tool Block will replace pracT1cally all of the tool holders and boring bar holders ordinarily required, combining them into one pracT1cal easyto-use unit. It may be used for heavy duty operaT1ons or, because of its compactness, for similar classes of work. An outstanding advantage is the screw adjustments for tool height wH1ch are easily made and need never be changed until all change in the height of the cutting edge of the tool becomes necessary. cutter H1ts may be removed, ground and replaced without the usual height adjustments. The tool block may be revolved to permit mounT1ng the tools from either the right or the left hand side. InstrucT1ons for using and 1a few of the many applicaT1ons are shown in the diagrams below. TURNING AND CNUTT1NG OFF To mount the 10 in 1 Tool Holder on the compound rest, first remove the NUT A and block from stud S . Then slide stud assembly into T-slot and tighten flat head screws F. Replace block and NUT, but do not tighten NUT until adjustment for tool height is made. Vertical adjusting screws are used to position the cutting tool. First make sure NUT A is loose enough to permit complete adjustment, then unscrew the back (adjusting screw (one farthest from work) and adjust front screw until cutting edge is at the desired height. Swivel the tool block to the correct position for taking the cut, and tighten NUT A with fingers only. Now tighten back vertical adjusting screw, and you are ready to take the cut. CNUT-off blades and cutter bits are( held in the tool slots by the 4 set screws labeled B in the diagram. Loosen these screws sufficiently to allow entry of the tool and then tighten the to lock the tool in place. BORING AND KNURLING Your Tool Block comes equipped with a self-aligning knurling head having No. 1151 medium diamond knurls. To change knurls or for using a boring bar, loosen the 4 cap screws labeled C and move plate A away from the main body to allow sufficient clearance for removal of the knurling head. When replacing, always tighten these screws enough to bring the plate solidly .against T1le main body of tool block. For all boring and knurling operaT1ons, invert the entire tool block. This place the boring or knurling tool at the correct height, without disturbing the height adjustment for the turning tool.
34
PARTS LIST Extra Knurls for Knurling Tool
THE TEN IN ONE TOOL BLOCK COMES EQUIPPED WITH A SELFALIGNING KNURLING HEAD HAVING No. CE3151 MEDIUM DIAMOND KNURLS. OTHER KNURLS ARE AVAILABLE AT EXTRA COST. ILLUSTRAT1ONS ABOVE SHOW ACTUAL SIZES OF KNURLING PRODUCED. SUPPLIED IN PAIRS
CAT. NO. CE3150 CE3151 CE3152 CE3153 CE3154 CE3155
10 in 1 Tool Block For 9”, LT. 10, 10”, 13”, 14 ½ “, 16” & 16/24
9” & LT 10 (A, B, & C) 10” (1” COL)
PATTERN
SIZE
FINE DIAMOND MED. DIAMOND COARSE DIAMOND FINE STRA1GHT MED, STRAIGHT COARSE STRAIGHT
5/8” x 5/16” 5/8” x 5/16 5/8” x 5/16 5/8” x 5/16 5/8” x 5/16 5/8” x 5/16
AVAILABLE ONLY AS SUB-ASSEMBLY PARTS INCLUDED ARE INDICATED B;Y THE ITEM NUMBERS APPEARING IN PAR. ENTHESIS AFTER PART NAME.
13”
14 ½ “
16” & 16/24”
PART NO.
PART NO.
PART NO.
PART NO.
PT283NK1 PT1673NR1 PT1464NR1 NOT USED NOT USED 121 X 16 121 X 228
PT283NK1 PT1673NR1 PT14E4NPl NOT USED NOT USED 121 X 16 121 X 228
PT283R1 PT1674T1 PT1464T1 PT1474T1 PT1473FH1 121 X 224 121 X 312
PT283R1 PT1675T1 PT1464T1 PT1474FFII PT1473FH1 121 X 224 121 X 412
PT283R1 PT1675T1 PT1464T1 PTl7'4FH1 PT1473FH1 121 X 224 121 X 412
PT1476NH1 *AS1475NH1 PT1461NK1 114 x 16
PT1476NH1 *AS1475NH1 PT1461R1 114 x 16 SEE 103 x 212 PT1462NR1 *AS1463R1 160 x 18
PT14674T1 *AS1475NH1 PT1461R1 114 x 124 TABULAT1ON 103 x 212 PT1462E1 *AS1463T1 120 x 906
PT1476NH1 *AS1475NH1 PT1461F1 114 x 224 ABOVE 103 x 614 PT1463F1 *AS1463F1 160 X 45
PT1476NH1 *AS1475NH1 PT1461H1 114 x 224
PART NAME ITEM NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17
PART NO. NUT WASHER STUD SNAP RING ADJ. PIN DOG PT. SCR ADJ. DOG PT. SCR BLOCK KNURL STUD KNURL HD. (18) CLAMP CAPSCREW KNURLS FLAT HD. SCR BASE CLAMP (1-2-3- 17) PIN OR SCREW
103 x 212 PT1462NR1 *AS1463NK1 160 x 18
35
103 x 618 PT1462H1 *AS1463H1 160 X 45
PARTS LIST
MILLING ATTACHMENT ENGLISH AND METRIC AVAILABLE ONLY AS SUB-ASSEMBLY. PARTS INCLUDED ARE INDICATED BY THE ITEM NUMBERS APPEARING IN PARENTHESIS AFTER PART NAME.
36
PARTS LIST 9” & LIGHT 10
10” (11/16” & 1” COL)
PART NO.
PART NO.
PART NAME ITEM NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31
HANDLE CRANK (1) GRAD. COLLAR - ENGLISH (5-6) GRAD. COLLAR - METRIC (5-6) SETSCREW BRASS PUNCH1NG PIN FEED SCREW-ENGLISH (7 14- 15- 16) FEED SCREW-METRIC (7- 14 1 5- 17) CLAMPING SCREW VISE (20-21) CAPSCREW V PLOCK COLLAR TAPER PIN FEED NUT-ENGLISH FEED NUT-METRIC SWIVEL 90LT PIN SETSCREW VISE GIB WRENCH CAPSCREW WASHER HEX. NUT WASHER BASE SADDLE(18- 1q) FEED SC. ENGLISH (7- 14- I 5- 1) FEED SC. METRIC (7- 14- 15- 17) SADDLE (IR- 19)
PART NAME ITEM NO 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 32 33 34
HANDLE CRANK (1) GRAD. COLLAR - ENGLISH ( S- 6) (RAD. COLLAR - METRIC (F- F) SETSCREW PRASS PUNCH1NG PIN FEED SCREW- ENGLISH (7- 14- 15- 17) FEED SCREW-METRIC (7-14-15-17) CLAMP ING SCREW VISE (20-21) CAPSCREW V BLOCK COLLAR TAPER PIN FEED .NUT- ENGLISH FEED NUT-METRIC SWIVEL BOLT PIN SETSCREW VISE -GIB WRENCH CAPSCREW WASHER HEX. NUT WASHER RASE SADDLE 1P-10 WRENCH (SINGLE END) CAPSCREW SOCKET HD SOCKET HO. WRENCH
PT1482 *AS830NH1
PT1482 * AS830NH1
*AS829NT1
*AS829NT1
*AS2243NT1 122x103 PT1078NK 1 160x46
*AS2243NT1 122x103 PT1078NK I 160x46
*AS832NK2
AS832R2
*AS2242NK1 PT836NR1 *'AS827NK1 111 x 12 PT831NK1 PT833NT1 168X206 PT828NR1 PT2241NR1 PT834NK1 160x18 122x210 PT835NK1 CE2655 112x120 112 x12 136x29 161X21 PT8 25NK2 *AS826NK1
*AS2242R1 PT83;NR1 *AS827R1 111 x 14 PT831R1 PT833NT1 168X206 PT82PNR1 PT2241NR1 PT834R1 160x18 122x512 PT835RI CE2655 112X120 161x12 136x31 161X27 PT825R1 *AS826R1
*AS832NK *AS2242NK2 *AS826FNK2
13’(11/16” & 1” COL.) PART NO PT1482 *ASP30NH1
14 ½ “ (3/4 “ & 1” COL) PART NO PT1482 *AS830NH1
*AS824NT1
*AS829FH1
*AS29 FH 1
*AS2243NT1 122x103 PT107RNK1 160X46
*AS2243FH1 122x104 PT1078NK1 160X46
*AS243FH1 122xI04 PT107RNK 1 160X46
*ASR32T2
*AS832FH2
*ASR32FH2
*AS2242T1
*AS2242FH1
*AS2242FH1
PT836T1 *ASR27T1 111x114 PT831T1 PTR33NT1 168X206 PT828T1 PT2241T1 PT834T1 160x45 122x514 PTR35T1 CE2656 11 2x4 24 1 I x27 13FX35 161x36 PTP25T1 *AS826T1 CE2R76 114x42R CE2390
PT836FH1 *ASR27FH1 111 x120 PT831FH1 PT833FH1 168 X208 PT828FH1 PT2241FH1 PT834FH 160X45 122x518 PT835FHPI CE2656 112x427 161x30 136 X39 161 x42 PT825FI *AS826FH2 CE267c 114x428 CF2390
PT836FH1 *ASR27FH1 111x120 PTRSIFH PT833FH1 168 X208 PTR28FH 1 PT2241FH1 PT834FH1 160x45. 122x51R PT835FH1 CE2656 112x42P 161X30 136X38 161 x42 PT825H2 *AS826FH2 CE267E 114x424 CF2390
37
16” & 16/24” (1” COL) PART NO. PT1482 *AS830NH1
PARTS LIST SERIAL NUMBER OF LATHE AND UNIT CODE NUMBER MUST ACCOMPANY ORDER
FOUR POSIT1ON CARRIAGE STOP FOR 9', 10K, 10.", 13", 14 ½ ", 16", 16/24” & 2H
AVAILABLE ONLY AS SUBASSEMBLY. PARTS INCLUDED ARE INDICATED BY THE ITEM NUMBERS APPEARING IN PARENTHESIS A FTER PART NAME.
PART NAME ITEM NO 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
STOP SCREW TAKE UP NUT SETSCREW FRAME OILER COIL SPRING STEEL BALL SPINDLE (2-9-10) BINDER SHOE SETSCREW CLAMP (12-13) JAM NUT SETSCREW WASHER CAPSCREW STOP SCREW
9"& 10K PART NO
10" PART NO
13" 14 ½ ", 16", '5/24'& 2H PART NO.
PT1219NH1 PT1218NH1 122x108
PT1219NH PT1218NH1 122x108
PT1219NH1 PT1218NH1 122x108
155x17 162X 54 172X12 *AS1217NH1 PT1080NK1 126x505 *AS1216NK1 139X23 122x518 161X63 114x120 PT1236K1
155x17 162X 54 172x12 *ASI217NH PT1080NK1 126x505 *AS1216RT1 139X23 122x524 16 1X2 114x120
155x17 16 2x 54 172X12 *AS1217NH1 PT1080NK1 126x505 *AS1216FH1 139x25 122x624 16 1 16 114x228
38
PARTS LIST SERIAL NUMBER OF LATHE AND UNIT COOE, NUMBER MUST ACCOMPANY ORDER
FOUR POSIT1ON CROSS SLIDE STOP FOR 9" 10K , 10", 13, 16", SERIES 900, 1000 AND 2H
AVAILABLE ONLY AS SUBASSEMBLY. PARTS INCLUDED ARE INDICATED BY THE ITEM NUMBERS APPEARING IN PARENTHESIS AFTER PART NAME.
PART NAME ITEM NO 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
CAPSCREW RUSH1NG STOP SCREW NUT TAKE UP NUT FRAME SETSCREW STEEL BALL COIL SPRING SETSCREW SPINDLE (4-11-12) SHOE SETSCREW CAPSCREW WASHER STOP SCREW
10K, PART NO
13" PART NO
16” & 2H PART NO.
114x116 PT1223NR2 PT811NH1 PT1222NH1
114x120 PT1223TH1 PT811NH1 PT1222NH1
114xl20 PT1223TH PT811NHQ PT1222NH1
122x102 172x12 162x1 126x505 *AS1221NH1 PT1078NK1 120x904 112x132 161x63 PT1224NH1
122x102 172x12 162x1 126x505 *AS1221NH1 PT1078NK1 120X904 112x224 161x16 PT1224NH1
122x102 172x12 162x1 126x505 *AS1221NH1 PT1078NK1 120x904 112x428 161x26 PT1224NH1
39
PARTS LIST
REGULAR FOLLOWER REST FOR 9 ; 10", 13", 14 ½ ", 16", 16/24" & 2H
AVAILABLE ONLY AS SUBASSEMBLY PARTS INCLUDED ARE INDICATED BY THE ITEM NUMBERS APPEARING IN PAR. ENTHESIS AFTER PART NAME.
PART NAME ITEM NO 1 2 3 4 4A 5 5A 5B SC 5D SE 6 7
HEX. CAPSCREW WASHER JAW Sq. HD. CAPSCREW FRAME FRAME FRAME FRAME FRAME FRAME .- . HEX. CAPSCREW WASHER
9” & 10” (1 COL.) PART NO 112X116 161X12 PT128NR1 118x128 118 x136 PT1 30N1 PT130R1 . --- - -. - - -. - - -. 112x132 161X63
13” PART NO
14 ½ “, 16”, 16/24" & 2H PART NO.
112x220 161X17 PT128T1 -- 118x240
112x220 161X17 PT128FH1 - - -. 118x248
PT130T1 - - -. - - -. PT2010H1 112x228 161X64
- - -. PT130F1 PT130H1
40
112x432 161X65
PARTS LIST SERIAL NUMBER OF LATHE AND UNIT CODE NUMBER MUST ACCOMPANY ORDER
TELESCOPING JAW FOLLOWER REST FOR 9", LIGHT 10, 10"-, 13", 14 ½ ", 16", 16/24" & 2H
AVAILABLE ONLY AS SUBASSEMBLY.PARTS INCLUDED ARE INDICATED BY THE ITEM NUMBERS APPEARING IN PARENTHESIS AFTER PART NAME.
PART NAME ITEM NO 1 2 3 4 5 6 7 8 9 10 11 11A 11B 11C 11D 11E 11IF 12 13
SNAP RING PIN SHOE ADJUSTMENT KNOB (1-2-3-6) ADJ. KNOB SLEEVE JAW ADJ. SCREW JAW LOCK SCREW KEY PIN FRAME (5-10) FRAME (5-10) FRAME (5-10) FRAME (5-10) FRAME (5-10) FRAME (5-10) FRAME 5- 10) WASHER CAPSCREW
9”, LT. 10 & 10"(1'COL) PART NO
13” PART NO
13" 14 ½”, 16", 16/24" 2H PART NO.
PT135NR1 160x25 PT1O82NT1
PT135T1 160X54 PT1O 2NT1
PT135FH1 160x55 PT1082FH1
*AS132NR1 PT131NR1 PT133NR1 PT129NR1 PT134NR1 PT137NR1 160X46 *AS 120N1 *AS120K 1 *AS120RI --------161X63 112x132
*AS132T1 PT131T1 PT133T1 PT129T1 PT134TH1 PT137TH1 160X47 ----- - -*AS120T1 ------161X17 112x228
*AS132FH1 PT131H1 PT133FH1 PT129FH1 PT134TH PT1 37TH I 160X47 --------*AS120F1 *A5120H1 *AS2009VI 161x65 112x432
41
PARTS LIST SERIAL NUMBER OF LATHE AND UNIT CODE NUMBER MUST ACCOMPANY ORDER
REGULAR STEADY REST FOR 9 ", 10", 1 3", 141", 16" AND 16/24" ALSO 16.' AND 16/24" EXTRA LARGE
42
PARTS LIST FOR 9”, 10”, 13” AND 14 ½ “ PART NAME ITEM NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 IS 19
Sq HD. SETSCREW HEX. NUT WASHER STEADY REST TOP STEADY REST JAW WASHER HEX. HD. CAPSCREW LOCK BOLT STEADY REST BASE PIN HEX. NUT WASHER PIN CLAMP MACH1NE BOLT CAPSCREW WASHER JAM NUT RAISING BLOCK
9” PART NO.
10” (1” COL) PART NO.
13” PART NO.
14 ½ “ PART NO.
118x136 138x25 161X12
118x136 138x25 161X12
118 x244 138x27 161X17
.30 .05 .05
118 x248 138x27 161X18
PT128NR1 161x12 112xl20 PT217NR1
PT128NR1 161X12 112x120 PT217NR1
PT128T1 161X17 112x220 PT217T1
1.65 .05 .05 1.35
PT12RFH1 161x17 112x220 PT217FH1
160X56 138X29 167X5 160X160 PT127NK4 143X208 ----------
160x56 138x31 1R7x6 160x60 PT127R1 143X309 ----------
160X60 138x35 167x8 PT1804 PT127T1 143x412 ----------
.05 .15 .05 .10 1.80 .40 .-.- .--
180x97 138x39 167x4 PT1804 PT1 27FI 147x 514 ----------
FOR 16" AND 16/24" REGULAR AND EXTRA LARGE
PART NAME ITEM NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
Sq. HD. SETSCREW HEX. NUT WASHER STEADY REST TOP STEADY REST JAW WASHER HEX. HD. CAPSCREW LOCK BOLT STEADY REST BASE PIN HEX. NUT WASHER PIN CLAMP MACH1NE BOLT CAPSCREW WASHER JAM NUT RAISING BLOCK
16" REGULAR PART NO.
16" EXTRA LARGE PART NO.
118x248 138x25 161x18
118x464 138x31 161X65
118x248 138x27 161x18
118x248 138x31 161x65
PT128FH1 161x17 112x220 PT217FH1
PT963H1 161x65 112x424 PT464H1
PT128FH1 161x17 112x220 PT217FH1
PT963H1 161x65 112x424 PTq64H1
160x97 138x39 167x9 PT1805 PT127H1 143x514 -------------
160x124 138x39 167x9 ---PT127H1 143x514 112x440 161x27 139x31 ----
160 x97 138x39 167x9 PT1805 PT127H1 143x534 ---------PT2003H1
160x124 138x39 167x9 ---PT1 27H1 143X34 112x440 161X27 139x31 PT962H1
43
16/24" REGULAR PART NO.
16/ 24" EXTRA LARGE PART NO.
PARTS LIST SERIAL NUMBER OF LATHE AND UNIT CODE NUMBER MUST A,CCOMPANY ORDERA
TELESCOPING JAW STEADY REST FOR 9", LT. 10, 10", 13", 141"; 16" AND 16/24" ALSO 16:' AND 16/24" EXTRA LARGE AVAILABLE ONLY AS SUBASSEMBLY. PARTS INCLUDED ARE INDICATED BY THE ITEM NUMBERS APPEARING IN PARENTHESIS AFTER PART NAME.
44
PARTS LIST FOR 9", LT. 10, 10", 13" AND 14 1/2 " ITEM NO 1 2 3 4 5 6 7 7A 7B 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23
PART NAME RING PIN ADJUSTMENT KNOB (1-2-4-6) SHOE KNOB SLEEVE JAW ADJ. SCREW JAW JAW - 4 5/8" JAW - 5 1/4" KEY LOCK SCREW HEX, NUT WASHER PIN CLAMP SQ. HD. BOLT HEX, NUT WASHER STEADY REST TOP LOCK BOLT (15-16-20) STEADY REST BASE PIN PIN SETSCREW RAISING BLOCK
9" & LIGHT 10 PART NO.
10" PART NO
13" PART NO
14 1/2" PART NO.
PT135NR1 160x25
PT135NR1 160x25
PT135T1 160x54
PT135FH1 160x55
*AS132NR1 PT1082NT1 PT131NR1 PT133NR1 PT129NR1 ------PT137NR1 PT134NR1 138x29 167x5 160x160 PT127NK4 143x208 138x25 161x12
*AS132NR1 PT1082NT1 PT131NR1 PT133NR1 PT129NR1 ------PT137NR1 PT134NR1 138x31 167x6 160x160 PT127R1 143x309 138x25 161x12
*AS132T1 PT1082NT1 PT131T1 PT133T1 PT129T1 ------PT137TH1 PT134TH1 138x35 167x8 PT1804 PT127T1 143x412 138x27 161x17
*AS132FH1 PT1082FH1 PT131FH1 PT133FH1 PT129FH1 ------PT137TH1 PT134TH1 138x39 167x9 PT1805 PT127F1 143x514 138x27 161x18
*AS217NR1
*AS217NR1
*AS217T1
*AS118FH1
160x56 160x46 -------
160x56 160x46 -------
160x60 160x47 -------
160x97 160x47 -------
FOR 16" AND 16/24" REGULAR AND EXTRA LARGE ITEM NO 1 2 3 4 5 6 7 7A 7B 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23
PART NAME RING PIN ADJUSTMENT KNOB (1-2-4-6) SHOE KNOB SLEEVE JAW ADJ. SCREW JAW JAW - 4 5/8" JAW - 5 1/4" KEY LOCK SCREW HEX, NUT WASHER PIN CLAMP SQ. HD. BOLT HEX, NUT WASHER STEADY REST TOP LOCK BOLT (15-16-20) STEADY REST BASE PIN PIN SETSCREW RAISING BLOCK
16" PART NO.
16" EXTRA LARGE PART NO
16/24" PART NO
16/24" EXTRA LARGE PART NO.
PT135FH1 160x55
PT135FH1 160x55
PT135FH1 160x55
PT135FH1 160x55
*AS132FH1 PT1082FH1 PT131FH1 PT133FH1 PT129FH1 ------PT137TH1 PT134TH1 138x39 167x9 PT1805 PT127H1 143x514 138x27 161x18
*AS132FH1 PT1082FH1 PT131FH1 PT133FH1 ---PT129FH1 PT963H2 PT137TH1 PT134TH1 138x39 167x9 PT1805 PT127H1 143x514 138x31 161x65
*AS132FH1 PT1082FH1 PT131FH1 PT133FH1 PT129FH1 ------PT137TH1 PT134TH1 138x39 167x9 PT1805 PT127H1 143x534 138x27 161x18
*AS132FH1 PT1082FH1 PT131FH1 PT133FH1 ---PT129FH1 PT963H2 PT137TH1 PT134TH1 138x39 167x9 PT1805 PT127H1 143x534 138x31 161x65
*AS118FH1
*AS964H1
*AS118FH1
*AS964H1
160x97 160x47 -------
160x124 160x47 109x12 ----
160x97 160x47 ---PT2003H1
160x124 160x47 109x12 PT962H1
45
PARTS LIST
SERIAL NUMBER OF LATHE AND UNIT CODE NUMBER MUST ACCOMPANY ORDER
SQUARE TURRET TOOL BLOCK FOR 9", 10-K, 10", 13", 14 1/2", 16", 16/24" AND 17"
ITEM NO
PART NAME
1 2 3 4 5 6 7 8 9 10 11 12 13 14A 14B 14C 14D 14E 14F 15 16 17 18 19 20 21 22 23 24 25
SETSCREW SQUARE TURRET TOOL ADJ. WEDGE INDEX PILOT WASHER CAPSCREW CAPSCREW PIN PIN SETSCREW BASE ORDER ITEM 22 EXPANSION PLUG RAISING BLOCK 9" LATHE ' ' LT. 10 ' ' ' 10" ' ' ' 13" ' ' ' 14 1/2" ' ' ' 16"-16/24" HEX, WRENCH HEX, WRENCH MACH, SCREW ADJUSTING SCREW CLAMP SHOE - LEFT CLAMP SHOE - RIGHT PIN ECCENTRIC (12-21-23-24) HANDLE BAKELITE BALL RAISING BLOCK
*AVAILABLE ONLY AS SUB. ASSEMBLY. PARTS INCLUDED ARE INDICATED BY THE ITEM NUMBERS APPEARING IN PAR. ENTHESIS AFTER PART NAME.
46
9", 10-K, 10" & 13" PART NO
14 1/2", 16", 16/24", 17" PART NO
121x116
121x 320
PT744NT2 PT759NT1 180x300 114x12 114x212 160x258 160x28 122x102 PT740NT2 PT751NT2 PT1502 PT762N1 PT762K1 PT762R1 PT762T1 -----CE2385 CE2389 107x110 PT761NT1 PT764NT1 PT763NT1 160x25 *AS758NT1 PT750NT1 PT406NT1
PT744FH2 PT759FH1 PT3400 114x120 114x424 160x258 160x59 122x102 PT740FH2 PT751FH2 PT1503 ------------PT762F1 PT762H1 CE2387 CE2390 107x316 PT761FH1 PT764FH1 PT763FH1 *AS758FH1 PT750FH2 PT406K&FH1 PT673GJ1
PARTS LIST
SERIAL NUMBER OF LATHE AND UNIT CODE NUMBER MUST ACCOMPANY ORDER
ITEM NO 1 2 3 4 5 6 7 7A 8 9 10 11 12 13 14 15 15A 16 17 18 19 20 21 22 23 24 25 26 27 28 29
*AVAILABLE ONLY AS SUB. ASSEMBLY. PARTS INCLUDED ARE INDICATED BY THE ITEM NUMBERS APPEARING IN PAR. ENTHESIS AFTER PART NAME.
9", 10-K, 10" & 13" PART NO
PART NAME SETSCREW SQUARE TURRET TOOL ADJ. WEDGE INDEX PILOT WASHER CAPSCREW CAPSCREW - FOR 9", 10", 13" & 16" CAPSCREW - FOR LT. 10 PIN PIN SETSCREW BASE ORDER ITEM 27 EXPANSION PLUG CAPSCREW PLATE - FOR LT. 10 PLATE - FOR 13" R. B. BINDING NUT HEX. WRENCH HEX. WRENCH MACHINE SCREW ADJUSTING SCREW CLAMP SHOE - LEFT CLAMP SHOE - RIGHT TEE SLOT NUT PIN HANDLE BAKELITE BALL ECCENTRIC (12-24-25-26) TURRET KEY MACH. SCREW
PART NO
121x116
121x320
PT744NT2 PT759NT1 180x300 114x12
PT744FH2 PT759FH1 PT3400 114x120
114x212 114x220 160x258 160x28 122x102 PT740NT2 PT751NT1 PT1502 114x228 PT770K1 PT770T2 PT772T1 CE2385 CE2389 107x110 PT761NT1 PT764NT1 PT763NT1 PT741NR2 160x25 PT750NT1 PT406NT1 *AS758NT1 -------
114x424 ---160x258 160x59 122x102 PT740FH2 PT751FH2 PT1503 ------------CE2387 CE2390 107x316 PT761FH1 PT764FH1 PT763FH1 PT741FH1 160x33 PT750FH2 PT406K&FH1 *AS758FH1 PT753FH1 103 X 208
SQUARE TURRET TOOL BLOCK for Double Tool Cross Side For 9", 10-K", 13", 16" and 2h
47
14 1/2", 16", 16/24", 17"
PARTS LIST
SERIAL NUMBER OF LATHE AND UNI CODE NUMBER MUST ACCOMPANY ORDER
HANDLEVER TURRET-TAILSTOCK TYPE TOP AND BASE ASSEMBLIES FOR 9". LT. 10. 10" ( 1 COL .) AND 13"
ITEM NO 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23
PART NAME CAPSCREW BOWL SCREW LINK LEVER PIN LINK SCREW LEVER WASHER HANDLE UPPER PLUG LOWER PLUG FELT WICK SNAP RING CLAMP WRENCH CLAMP NUT WASHER OILER SETSCREW SET-OVER SCREW STOP SCREW RING CAPSCREW HEX NUT STOP SCREW STOP SCREW WRENCH
9" PART NO. 114x340 PT173BNT1 PT1745NT1 PT1735NT2 PT1734NT1 PT1746NT1 PT1709NR1 PT3122NR1 PT1747NT1 PT249T2 256x2 PT1737NT1 CE2653NK PT283NK1 PT2861NK1 155x20 120x5 PT278NK1 PT1729NT2 114X10 138x24 PT1730NT1 PT1727NT1
LT. 10 PART NO 114x340 PT1738NT1 PT1745NT1 PT1735NT2 PT1734NT1 PT1746NT1 PT1709NR1 PT3122NR1 PT1747NT1 PT249T2 256x2 PT1737NT1 CE2653NK PT283NK1 PT2861NK1 155x20 120x5 PT278NK1 PT1729NT2 114x10 138x24 PT1730NT1 PT1727NT1
48
10” (1” COL.) PART NO 114x340 PT1738NT1 PT1745NT1 PT1735NT2 PT1734NT1 PT1746NT1 PT1709NR1 PT3122NR1 PT1747NT1 PT249T2 256x2 PT1737NT1 CE2653R PT283R1 PT1720R1 155x20 120x5 PT278R1 PT1729NT2 114x10 138x24 PT1730NT1 PT1727NT1
13" PART NO. 114x340 PT173RNT1 PT1745NT1 PT1735NT2 PT1734NT1 PT1746NT1 PT1709NR1 PT3122NR1 PT1747NT1 PT249T2 256x2 PT1737NT1 CE2653T PT283T1 PT238T1 155x20 120x5 PT278TF1 PT1729NT2 114x10 138x24 PT1730NT1 PT1727NT1
PARTS LIST ITEM NO. 24 25 26 27 28 29 30 31 32 33
PART NAME
MACH, SCREW FELT RETAINER-FRONT WIPER T. S. TURRET TOP FELT WICK FELT RETAINER-REAR PIN CLAMP BASE CLAMP BOLT
9" PART NO.
LT. 10 PART NO.
10" (1”COL.) PART NO.
13” PART NO.
PT1164-1 PT581K2 PT582K1
PT1164-1 PT581K2 PT582K1
PT1164-1 PT581K2 PT582K1
PT1164-1 PT581K2 PT582K1
256x1 PT580K2 160x18 PT56NK2 PT51K3 143x214
256x1 PT580K2 160x18 PT56NK2 PT1717K2 143x216
256x1 PT580R2 160x18 PT56R1 PT51R3 143x317
256x1 PT580T2 160x18 PT56T1 PT51T3 143x422
ITEM
9". LT. 10. 10" & 13" PART NAME
NO. 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75
HANDLEVER TURRET-TAILSTOCK TYPE HEAD AND SPINDLE ASSEMBLIES FOR 9". LT. 10. 10"( 1 COL.) AND 13” 49
PART NO. SETSCREW SETSCREW JAM NUT OILER PIN FELT WICK COMPRESSION SPRING INDEX PLATE CAPSCREW DOWEL PIN PIN INDEX PIN SETSCREW BINDER PLUG PINION (49) PIN PLUG SPRING PLUNGER SPRING SPRING HOUSING CAPSCREW PIN WASHER HEAD COIL SPRING DR IVER BEVEL GEAR BOWL SETSCREW CENTER POST TAPER PIN BEVEL GEAR (65) ROTOR ROD BUSH1NG SPINDLE (68-70-71) * KEY PIN SETSCREW ROTOR (72) JAM NUT BORING BAR
120x10 126 x505 PT1062- 1 155x20 160X240 256x1 PT1715NT1 PT1722NT1 114x20 153x10 160x25 PT1744NT1 126 x604 PT4931S1 *AS1741NT1 PT1822 PT1742NT1 162x53 PT1743NT1 162x49 PT1716NT1 11 4x10 160x25 PT3037NR1 PT1721NT2 162x20 PT17 24NT2 PT1726NT2 126x505 PT1740NT2 168x107 *AS1725NT2 PT1732NT1 PT1739NT2 *AS1733NT2 PT285KR1 160x19 120x4 *AS1731NT2 139x23 CE3420
PARTS LIST EXTERNAL GRINDER FOR 9", 10-K, It", 13" , 1 6 ", 16/24': 17-
ITEM NO 1 2 3 4 5 6 7
ITEM NO. 8 9 10 II 12 13 14 15 16 17 18 19 20 21 22 23 39 40
PART NAME CLAMP (2-3) PIN CLAMP STUD RAISING BLOCK WASHER CLAMPING NUT CLAMP BOLT EQUIPMENT (1-4-5-6)
9" & 10-K PART NO.
10” PART NO.
13" PART NO.
14-1/2" PART NO.
16" & 16/24” PART NO.
17” PART NO.
AS1577NK1 160 x 19 PT1585NR1 ---------------161 x 22 PT283NK1
*AS1577R1 160 x 19 PT1585NR1 ---------------161 x 22 PT283NK1
*AS1577T1 160 x 21 PT1585T1 PT1586T1 161 x 22 PT283NK1
*AS1577F1 160 x 21 PT1S85F1 PT596F1 161 x 22 PT283NK1
*AS1577H1 160 x 21 PT1585H1 PT1586H1 161 x 22 PT283NK1
PT1585H1 PT1586GJ1
CE307NK
CE307R
CE307T
CE307F
CE307H
CE307GJ
PART NAME
PART NO
GRINDER CAP CASTELLATED NUT WASHER SPRING WASHER BEARING GRINDER FRAME GRINDER SPINDLE GRINDER SPINDLE PULLEY WHEEL GUARD GRINDING WHEEL WHEEL FLANGE NUT CAPSCREW WASHER BELT
PT1592NH1 PT1070NH1 161 x 27 PT1588NH1 161 x 68 PT502NH1 PT1575NH1 PT1579NH1 PT1584NH1 PT1576NH1 CE2759 PT1580NH1 PT11056NH1 112 x 110” 161 x 12 CE3L220
ITEM NO. 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38
PART NAME
PART NO.
SETSCREW 120 x 4 SETSCREW 120 x 6 MOTOR PULLEY - 1/2" (24) *AS1583NH2 MOTOR PULLEY 5/8" (24) *AS1582NH2 MOTOR-SPECIFY, H.P., PHASE, CYCLE & VOLT MOTOR BASE PT1574NH1 MOTOR BASE PT1573NH1 CAPSCREW 112 x 110 BELT T1GHTENER ADJ. SCREWV PT1587NH1 TOGGLE SWITCH SE4679 CORD SET CE3659 CAPSCREW PT2900NH1 COTTER PIN 170 x 206 PIN PT1803 ADAPTER PT6883 SPACER PT1580-2 SETSCREW 126 x 762 SOC. HD. SCREW 114 x 220
50
*AS1577H1
PT283NK1
PARTS LIST EXTERNAL GRINDER GRINDING WHEELS CUP 4" DIAMETER, ½" FACE, AND 1" HOLE CE2759 CE2758 CE2774 CE2757 CE2769
FOR " " " "
GRINDING WHEEL
GENERAL WORK - ROUGH OR FINISH CNUTT1NG TOOLS- " " " ANUTOMOBILE VALVES- “ " “ CAST IRON - FINISH GRINDING SOFT STEEL “ “ “
3 ¼" ONUTSIDE DIAMETER, 14" FACE. 1" HOLE CE3236 FOR SHARPENING REAMERS & CNUTTERS
INSTRUCTION The External Grinder Attachment is mounted in the compound T-slot with item 7 clamp assembly as shown below:
LUBRICATION - GRINDER. The spindle revolves in pre-lubricated, precision ball bearings which are sealed to protect them from damage and requires no further lubrication.
LUBRICATION - MOTOR (1-PHASE) After 3 years normal or 1 year heavy duty service add oil annually. No recoiling normally required for light duty with total operating Time under 25,000 hours. Use electric motor oil. Do not over oil.
51
PARTS LIST INTERNAL GRINDER FOR 9”, 10-K, 10”, 13”, 14 ½”, 16”, 16/24” AND 17”
ITEM NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63
*AVAILABLE ONLY AS SUBASSEMBLY. PARTS INCLUDED ARE INDICATED BY THE ITEM NUMBERS APPEARING IN PARENTHESIS AFTER PART NAME.
52
PART NAME RETAINER CAP (2-3) FELT SPLIT WASHER RETAINER NUT BALL BEARING JACKSHAFT SPINDLE JACKSHAFT SPACER RETAINING RING SETSCREW JACKSHAFT HOUSING (9-11-12) STRAIGHT PIN OILER RETAINER CAP CAPSCREW JACKSHAFT PULLEY (17) BELT SETSCREW SPINDLE NOSE PROTECTOR RETAINER NUT RETAINER SEAL BEARING SPINDLE BELT ADJ. SCREW (29-30) SPACER - FRONT (25) COIL SPRING SPACER- REAR FRAME (28-34) OILER BELT TIGHTNER ADJ, KNOB PIN Adapter SPINDLE PULLEY LOCK NUT SETSCREW BRACKET SCREW SCREW SCREW SPACER BELT GUARD (41-42) INSIGNIA PLATE DRIVE SCREW BELT SCREW MOTOR PULLEY MOTOR PULLEY (44) MOTOR - SPECIFY CORD SET (FOR 1 PH, ONLY) SWITCH (FOR 1 PH. ONLY) CAPSCREW WASHER END WRENCH CHUCK (54) CHUCK NUT ARBOR (56-57) WASHER NUT ARBOR (56-57) ARBOR (57-60) WASHER ARBOR (57-60) GRINDING WHEEL GRINDING WHEEL SERIAL NUMBER OF LATHE AND UNIT CODE NUMBER MUST ACCOMPANY ORDER.
PART NO. *AS2411NH1 PT2421NH1 PT2422NH1 PT2410NH1 PT2450NH1 PT2430NH2 PT2424NH1 PT2444NH1 121 X 5 *AS2429NH2 PT1825-1 PT2679-1 PT2443NH1 115 X 248 *AS2419NH2 PT2438NH1 120 X 903 PT2449NH1 PT2406NH1 PT2407NH1 PT2437NH1 PT2401NH1 *AS2432NH1 *AS2408NH1 162 X 54 PT2409NH1 *AS2400NH2 PT2679-1 PT2433NH1 160 X 25 PT6883 PT2412NH1 PT2415NH1 121 X 5 PT2470NH1 101 X 308 101 X 312 101 X 308 PT2471NH1 *AS2431NH1 PT3300 130 X 100 PT2439NH1 122 X 505 *AS2472NH1 *AS2414NH1 PT1104-2 SE4679 112 X 8 PT1679-1 PT2458-2 '*AS2403NH2 PT2402NH2 *AS2425NH1 PT2442NH1 138 X 24 *AS2426NH 1 *AS2427NH1 PT2404NH1 *AS2428NH1 CE2925 CE2926
PARTS LIST
CLAMP BOLT ASSEMBLY
ITEM NO. 1 2 3 4 5 6 7
PART NAME CLAMP (2-3) PIN CLAMP STUD RAISING BLOCK WASHER CLAMPING NUT CLAMP BOLT EQUIPMENT (1-4-5-6)
9” AND 10 K PART NO. *AS1577NK1 160 X 19 PT1585NR1 ---------161 X 22 PT283NK1
10” PART NO. *AS1577R1 160 X 19 PT1585NR1 ---------161 X 22 PT283NK1
13” PART NO. *AS1577T1 160 X 19 PT1585T1 PT1586T1 161 X 22 PT283NK1
14 ½” PART NO. *AS1577F1 160 X 21 PT1585F1 PT1586F1 161 X 22 PT283NK1
16” & 16/24” PART NO. *AS1577H1 160 X 21 PT1585H1 PT1586H1 161 X 22 PT283NK1
17” PART NO. *AS1577H1 160 X 21 PT1585H1 PT1586GJ1 161 X 22 PT283NK1
CE307NK
CE307R
CE307T
CE307F
CE307H
CE307GJ
INSTRUCTION The internal grinder attachment mounts o n the compound rest top. Adjust the belt to proper tension with belt adjusting screw item 23. The grinder spindle and the jackshaft spindle run on high speed ball bearings which require no adjustment. LUBRICATION - GRINDER Remove oil screws periodically, items 12 and 18, and add a few drops of spindle bearing oil at both points. Use SBL CE1600 oil or equal. LUBRICATION - MOTOR (1 PHASE) Motors having ball bearings are packed with grease sufficient for about two years of normal service. At the end of that time, the bearings should be cleaned thoroughly of the old grease and repacked about one-third full with General Electric ball-bearing grease.
53
PARTS LIST SERIAL NUMBER OF LATHE AND UNIT CODE NUMBER MUST ACCOMPANY ORDER.
MICA UNDERCUTTING ATTACHMENT FOR 9",10 K 10”, 13", 14 ½”, 16"
*AVAILABLE ONLY AS SUBASSEMBLY. PARTS INCLUDED ARE INDICATED BY THE ITEM NUMBERS APPEARING IN PARENTHESIS AFTER PART NAME. UNIT CODE NUMBER STAMPED HERE
ITEM NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 ITEM NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21
PART NAME LEVER STUD SCREW SHOULDER SCREW JAM NUT SETSCREW LOCK NUT THUMB SCREW FORK (4-5) GUIDE BLADE HOLDER (14-15) BLADE - .020" TH1CK BLADE - .015" TH1CK WASHER WASHER CAPSCREW BRACKET (16) COLLAR SCREW HEX JAM NUT WASHER BLADE CLAMP MACHINE SCREW PART NAME LEVER STUD SCREW SHOULDER SCREW JAM NUT SETSCREW LOCK NUT THUMB SCREW FORK (4-5) GUIDE BLADE HOLDER (14-15) BLADE - .020" THICK BLADE - .015" THICK WASHER WASHER CAPSCREW BRACKET (16) COLLAR SCREW HEX JAM NUT WASHER BLADE CLAMP MACHINE SCREW
9” PART NO. PT1446NH2 PT1448NH1 PT1447NH1 139 X 27 PT703NH1 PT 1437NH1 131 X 26 *AS1449NH1 PT1443NH2 *AS1444NH1 CE2029 CE2028 161 X 63 161 X 12 112 X 132 *AS1442N1 PT212R1 139 X 25 161 X 12 PT1441NH1 102 X 310 14 ½” PART NO. PT1446NH2 PT1448NH1 PT1447NH1 139 X 27 PT703NH1 PT1437NH1 131 X 26 *AS1449NH1 PT1443NH2 *AS1444NH1 CE2029 CE2028 ---------161 X 26 112 X 436 *AS1442F1 PT1436FH1 139 X 25 161 X 12 PT1441NH1 102 X 310
10 K & 10” (1”COL) PART NO. PT1446NH2 PT1448NH1 PT1447NH1 139 X 27 PT703NH1 PT 1437NH1 131 X 26 *AS1449NH1 PT1443NH2 *AS1444NH1 CE2029 CE2028 161 X 63 161 X 12 112 X 132 *AS1442KR1 PT212R1 139 X 25 161 X 12 PT1441NH1 102 X 310 16” PART NO. PT1446NH2 PT1448NH1 PT1447NH1 139 X 27 PT703NH1 PT1437NH1 131 X 26 *AS1449NH1 PT1443NH2 *AS1444NH1 CE2029 CE2028 ---------161 X 26 112 X 436 *AS1442H1 PT1436FH1 139 X 25 161 X 12 PT1441NH1 102 X 310
54
13” PART NO. PT1446NH2 PT1448NH1 PT1447NH1 139 X 27 PT703NH1 PT1437NH1 131 X 26 *AS1449NH1 PT1443NH2 *AS1444NH1 CE2029 CE2028 ----------161 X 16 112 X 236 *AS1442T1 PT1436T1 139 X 25 161 X 12 PT1441NH1 102 X 310
PARTS LIST *AVAILABLE ONLY AS SUBASSEMBLY. PARTS INCLUDED ARE INDICATED BY THE ITEM NUMBERS APPEARING IN PARENTHESIS AFTER PART NAME.
SERIAL NUMBER OF LATHE AND UNIT CODE NUMBER MUST ACCOMPANY ORDER.
HAND LEVER TAILSTOCK FOR 9", 10-K, & 10"
ITEM NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 13A 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38
PART NAME BOLT WASHER TAILSTOCK CLAMP TAILSTOCK TOP TAILSTOCK BASE NUT TAILSTOCK WRENCH SET OVER SCREW TAILSTOCK SPINDLE KEY TAILSTOCK SPINDLE HARD CENTER PIN UPPER PLUG LOWER PLUG BINDING LEVER (14A-14B) OILER TAILSTOCK SCREW TAILSTOCK SCREW BARREL BUSHING (19-20-21) PIN SCREW COLLAR SCREW SLIDING BUSHING {23-24-25) OILER SCREW BINDER SHOE HANDWHEEL (28-29-35) HANDWHEEL (28-29-35) HANDLE STUD HANDLE PT 1480 NUT HANDLE LEVER WASHER PIN HAND LEVER PIN LEVER LINK LINK SCREW LINK SCREW
9” PART NO. 143 X 214 PT2861NK1 PT56NK2
LIGHT 10 PART NO. 143 X 216 PT2861NK1 PT56NK2
10” (11/16” & 1” COL.) PART NO. 143 X 317 PT1720R1 PT56R1
PT51N1 PT283NK1 CE2653NK PT278NK1 PT286NR1 PT201NR1 CE2401 ---------------------------PT54NK1 ---------*AS1706NK1 ---------*AS1700NK1 160 X 46 111 X 112 PT872NK1 *AS1703NR1 155 X 17 118 X 112 PT1075NR1 *AS53NK1 ------------------PT1480 ---------PT3122NR1 PT1709NR1 ---------PT1707NR1 168 X 106 PT1711NR1 PT1710NR1 PT1712NR1
PT1701K1 PT283NK1 CE2653NK PT278NK1 PT286NR1 PT201NR1 CE2401 ---------------------------PT54NK1 ---------*AS1706NK1 ---------*AS1700NK1 160 X 46 111 X 112 PT872NK1 *AS1703NR1 155 X 17 118 X 112 PT1075NR1 *AS53NK1 ------------------PT1480 ---------PT3122NR1 PT3122NR1 ---------PT1707NR1 168 X 106 PT1711NR1 PT1710NR1 PT1712NR1
PT51R1 PT283R1 CE2653R PT278R1 PT286NR1 PT201NR1 CE2401 160 X 48 PT248KR3 PT249KR3 *AS54KR2 155 X 23
55
*AS1706R1 *AS1700R1 ---------111 X 112 PT872R1 *AS1703NR1 155 X 17 118 X 112 PT1075NR1 *AS1262R1 PT1242 PT1492 136 X 25 PT3122NR1 PT1709NR1 160 X 19 PT1707NR1 PT1711NR1 PT1710NR1 PT1712NR1
PARTS LIST TOOL and REAMER ATTACHMENT FOR 9”, LT. 10, 10”, 13”, 14 ½”, 16” & 16/24”
*AVAILABLE ONLY AS SUBASSEMBLY. PARTS INCLUDED ARE INDICATED BY THE ITEM NUMBERS APPEARING IN PARENTHESIS AFTER PART NAME.
SERIAL NUMBER OF LATHE AND UNIT CODE NUMBER MUST ACCOMPANY ORDER.
56
PARTS LIST 9" & LIGHT 10 ITEM NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29
PART NUMBER BOLT CLAMP WASHER NUT BOLT (8-9) SPRING STOP PLATE SPRING STOP SOCKET (10) WASHER NUT CAPSCREW SPRING STOP SHANK (12-13) SPRING STOP - VERTICAL SCREW SPRING STOP BAR (15-16) SPRING STOP - HORIZONTAL SCREW SWIVEL BAR - SHORT (18) SETSCREW SWIVEL BAR - MEDIUM (20) SETSCREW SWIVEL BAR - LONG (22) SETSCREW SWIVEL BAR (24) SETSCREW HEX WRENCH SPRING STOP SHANK (27-28) SPRING STOP SCREW RAISING BLOCK
PART NO. 143 X 210 PT127NK4 161 X 25 136 X 29 NOT USED NOT USED *AS1226NR1 NOT USED NOT USED 112 X 16 *AS1227NH1 PT1229NH1 101 X 107 *AS1234NH1 PT1235NH1 101 X 306 *AS1231NH1 119 X 108 *AS1232NH1 119 X 108 *AS1233NH1 119 X 108 *AS1594NH11 120 X 4 173 X 6 *AS1595NH1 PT1596NH1 103 X 210 ....................... 14 1/2”
ITEM NO. 1 2 3 4 5 6 7 B 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29
PART NUMBER BOLT CLAMP WASHER NUT BOLT (8-9) SPRING STOP PLATE SPRING STOP SOCKET (10) WASHER NUT CAPSCREW SPRING STOP SHANK (12-13) SPRING STOP - VERTICAL SCREW SPRING STOP BAR (15-16) SPRING STOP - HORIZONTAL SCREW SWIVEL BAR - SHORT (18) SETSCREW SWIVEL BAR - MEDIUM (20) SETSCREW SWIVEL BAR - LONG (22) SETSCREW SWIVEL BAR (24) SETSCREW HEX WRENCH SPRING STOP SHANK (27-281 SPRING STOP SCREW STOP RAISING BLOCK
PART NO. 143 X 514 PT127F 161 X 41 136 X 39 PTS17FH1 PT1225F1 'AS1226FH1 161 X 65 136 X 31 112 X 216 *AS1227NH1 PT1229NH 1 101 X 107 *AS1234NH1 PT1235NH1 101 X 306 *AS1231NH1 119 X 108 *AS1232NH1 119 108 *AS1233NH1 119 X 108 *AS1594NH1 120 X 4 173 X 6 *AS159SNH1 PT1596NH1 103 X 210 .......................
57
10" (11/16” & 1” COL. PART NO. 143 X 312 PT127R1 161 X 30 136 X 30 NOT USED NOT USED *AS1226NR1 NOT USED NOT USED 112 X 16 *AS1227NH 1 PT1229NH1 101 X 107 *AS1234NH1 PT1235NH1 101 X 306 *AS1231NH1 119 X 108 *AS1232NH1 119 X 108 *AS1233NH1 119 X 108 *AS1594NH1 120 X 4 173 X 6 *AS1595NH1 PT1596NH1 103 X 210 ..................... 16”
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
PART NO. 143 X 514 PT127H1 161 X 41 136 X 39 PT517FH1 PT1225H1 *AS1226FH1 161 X 65 136 X 31 112 X 216 *AS1227NH1 PT1229NH 1 101 X 107 *AS1234NH1 PT1235NH1 101 X 306 *AS1231NH1 119 X 108 *AS1232NH1 119 X 108 *AS1233NH1 119 X 108 *AS1594NH1 1120 X 4 173 X 6 *AS159SNH1 PT1596NH1 103 X 210 .....................
13" PART NO. 143 X 410 PT127T1 161 X 36 136 X 35 PTS17T1 PT122ST1 *AS1226T1 161 X 65 136 X 31 112 X 116 *AS1227NH1 PT1229NH1 101 X 107 *AS1234NH1 PT123SNH1 101 X 306 *AS1231NH1 119 X 108 *AS1232NH1 119 X 108 *AS1233NH1 119 X 108 *AS1594NH1 120 X 4 173 X 6 *AS1S95NH1 PT1596NH1 103 X 210 ....................... 16/24"
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
PART NO. 143 X 534 PT127H1 161 X 41 136 X 39 PT517FH1 PT1225H1 *AS1226FH1 161 X 65 136 X 31 112 X 216 *AS1227NH1 PT1229NH1 101 X 107 *AS1234NH1 PT1235NH1 101 X 306 *AS1231NH1 119 X 108 *AS1232NH1 119 X 108 *A51233NH1 119 X 108 *AS1594NH1 120 X 4 173 X 6 *AS1595NH1 PT1596NH1 103 X 210 PT2003H1
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
58
59
By Order of the Secretary of the Army:
E. C. MEYER General, United States Army Chief of Staff Official:
J. C. PENNINGTON Major General, United States Army The Adjutant General
DISTRIBUTION:
* U.S. GOVERNMENT PRINTING OFFICE: 1995 - 388-421/40083
PIN : 047809-000
This fine document... Was brought to you by me:
Liberated Manuals -- free army and government manuals Why do I do it? I am tired of sleazy CD-ROM sellers, who take publicly available information, slap “watermarks” and other junk on it, and sell it. Those masters of search engine manipulation make sure that their sites that sell free information, come up first in search engines. They did not create it... They did not even scan it... Why should they get your money? Why are not letting you give those free manuals to your friends? I am setting this document FREE. This document was made by the US Government and is NOT protected by Copyright. Feel free to share, republish, sell and so on. I am not asking you for donations, fees or handouts. If you can, please provide a link to liberatedmanuals.com, so that free manuals come up first in search engines:
Free Military and Government Manuals
– Sincerely Igor Chudov http://igor.chudov.com/ – Chicago Machinery Movers
