Tmk 120 R Installation Guide

Transcript

TMK 120 R • Installation Guide The TMK 120 R Table Mount Kit allows under-table installations for one or two Retractors. The kit secures the Retractors to the underside of a table. Included Parts Included Parts NOTE: When selecting a mounting location, consider that cables are connected to the Retractor from the rear, the retractor button assembly protrudes from the front of the bracket, and the button assembly must be readily visible to prevent accidental contact.  Place the TMK 120 R under the table Included Parts Included Parts at the desired mounting location. Mark the two keyhole locations. Included Parts  Drill 3/32-inch (2.4 mm) diameter, 1/4 inch (6.3 mm) deep pilot holes. Bracket (1)  Install (2) #6 x 1/2 inch wood screws (2) (2) Hanger 1/4-20(provided) x 1 1/2" into the pilot holes. #6 x 1/2" #6-18 x 1/2" (4) Tighten until 1/4-20 x 1 1/2" (4)(4) x 1/2" 1/4 inch#6-18 protrudes. Phillips pan head Phillips wood Wood Screws Panscrews Head(4) Screws Wood Screws screws (4) #6-18 x 1/2" (4) 1/4-20 x 1 1/2" (4) Wood Screws Phillips Pan Head Screws ATTENTION: #6-18 x 1/2" (4) 1/4-20 x 1 1/2" (4) • Do not drillPhillips through table or furniture. If the table is too thin or of a different Wood Screws Panthe Head Screws material for the supplied screws, use an appropriate type and length. • Ne perçez pas à travers la table ou le meuble. Si la table est trop fine ou faite dans un matériau différent de celui pour lequel les vis fournies sont prévues, utilisez un type de matériau et une longueur appropriés. Mount the TMK 120 R bracket as follows:  Place the TMK 120 R under the table at the desired mounting location. Mark the two keyhole locations.  Drill 3/32-inch (2.4 mm) diameter, 1/4 inch (6.3 mm) deep pilot holes.  Install (2) #6 x 1/2 inch wood screws (2) (provided) into the pilot holes. Tighten until 1/4 inch protrudes. Tighten  Slide the mounting bracket onto the screws.  Tighten the two screws. Install the Retractor as follows: NOTE: Do not overtighten. The locking screw only needs to be snug. Locking Screw 2 PRESS PRESS 4 1 3 Rotate (if necessary) 1 Remove the top and bottom retractor enclosure screws. 2 Install the retractor with the cable release button against the bracket sidewall. 3 Install and tighten a provided 1/4-20 x 1 1/2" pan head screw. 4 If necessary, rotate the retractor housing for access, then tighten the locking screw. 5 Rotate the rear of the retractor enclosure to the final installation position and install the hanger to the retractor with a provided 1/4-20 x 1 1/2" pan head screw. 6 Mark the desired mounting position of the hanger under the table and drill a 3/32" diameter, 1/4" deep pilot hole. 6 TMK 120 R 7 5 7 8 Fasten the hanger under the table using a provided #6 x 1/2" wood screw. Repeat steps 1-8 to install a second retractor. Extron USA Headquarters +1.800.633.9876 (Inside USA/Canada Only) Extron USA - West Extron USA - East +1.714.491.1500 +1.919.850.1000 +1.714.491.1517 FAX +1.919.850.1001 FAX Extron Asia +65.6383.4400 +65.6383.4664 FAX Extron Middle East +971.4.299.1800 +971.4.299.1880 FAX Extron Europe +800.3987.6673 (Inside Europe Only) +31.33.453.4040 +31.33.453.4050 FAX Extron India 1800.3070.3777 (Inside India Only) +91.80.3055.3777 +91.80.3055.3737 FAX Extron Japan +81.3.3511.7655 +81.3.3511.7656 FAX Extron China +86.21.3760.1568 +86.21.3760.1566 FAX Extron Korea +82.2.3444.1571 +82.2.3444.1575 FAX © 2014 Extron Electronics — All rights reserved. All trademarks mentioned are the property of their respective owners. www.extron.com 68-2648-50 Rev. A 08 14