Touch Interface With Universal Video Converter _v100709

Transcript

Touch Interface with universal video converter _V100709 This interface can converter touch panel signals into DVD /TV IR signals, or iPod control signal, so when people watch DVD inside a car, he does not need a remote controller any more. This interface can also be programmed to a new Remote controller in the installation process. The various versatile video conversion inside makes this interface suitable for almost every car which has a video or RGB input. The main features are: 1. People can enjoy DVD or video source without remote controller while dirct touching the icons on top of the screen.Dedicated icons are mixed inside the video stream for easy read and touch operations. 2. Several video source can added onto a single screen without added extra keypad to select them. 3. This interface has a programing function which allows a new remote controller to be recorded. 4. This is a an upgrade version from Navlinkz FV-02 and FV-09 video converter which haven been sold for several years, it is very versatile and easy for installers in video conversion purposes while installed in almost whatever car which has a video or RGB input connector, and it can handle almost all video input[NTSC,PAL,SECAM, in CVBS or RGB], while offer a very stable standard video output. 5. Multi-point touch screen calibration algorithm inside makes this interface can be installed with almost every screen, no matter original touch screen or added. 1. System structure： Navi RGB CVBS camera Video input 800X480 64 Mega bit Dynamic memory Analog to Digital convert er RGB Video output Digital to Analog conver ter Touch icon generation： 6Pin power IR output CVBS touch Note： (1) Video is memorized into 64M SDRAM first, then read out and encoded back into video, to guarantee that output is always fixed into one stable format, no matter what the input is although the input and output are showing the same video picture. The input can be: NTSC，PAL，SECAM, VGA，in RGB or CVBS format，the PAL/NTSC/SECAM inputs are automatically detected and processed. The output can be : PAL，NTSC，VGA，RGB in RGB or CVBS format. the PAL/NTSC,CVBS/RGB/VGA output are selected by DIP switch. (2) the Navi RGB and AV input signals from the input side are digitized into 800XRGBX48 0high definition signals first, then recoded from the memory tank to generate RGB or AV signals again. 2．DIP switch settings DIP When =ON side When =OFF side（Stay up side） 1 Navi-RGB input enabled Navi-RGB input disabled 2, AV1 input enabled AV1 input disabled 3 AV2 input enabled AV2 input disabled 4 The navi RGB=VGA resolution[800X600@60Hz] The navi RGB=NTSC resolution 5 If Reverse signal（Green wire=12V）happens, video goes to CAM video If Reverse signal（Green wire=12V）happens, video goes to car original video This function can be ignored by leave away the green wire. 6 When DIP6=ON, this interface go to IR program mode to record the new ir code. Refer to “Ir programming” part for details. Set to “OFF” for normal use. When DIP6 goes to ON/off 6 times, this interface go to touch calibration mode to get tuned to a new touch panel. Refer to “touch calibration” part for details. 7，8 Output format： (off,off)： (off,on)： (on,off)： (on,on)： output=NTSC composite video output =PAL composite video output =RGB-NTSC component video output =RGB-VGA The LED below is for power indicator. The LED up is for IR indicator, when there is IR output, the led blinks. 3．Wiring diagram SOG [sync on UP row: output of Down row：input of Green] output RGB+sync, Car RGB+sync CVBS output DIP switches NAVI RGB IN AV1/2 TV/DVD 6Pin POWER CVBS in IR out 6Pin POWER conn. For the Interface box : YELLOW: 12V battery power, it can also be ACC. RED=ACC：whenthis wire goes to 12V, the interface works. BLACK：Ground for chassis。 GREEN: go to camera video when this wire=12V. white： switch signal when >5V.[max 25V] GRAY： specific control signal from the CAN box, do not connect to anything. RGB output connector： The up row is RGB output，the below row is RGB input，see below for details The 2 jacks are: SOG ouput[sync on Green] and CVBS output。 The CVBS can be connected to the video input of a monitor directly. AV1,AV audio input RGBoutput signals：from left to right： RED out，GREEN out，Blue out，Csync out，GND，left sound out，right sound out，12V indicator. CAR RGBinput signals：from left to right： RED in, Green In, Blue In, CSync In, GND, Hsync Out,Vsync Out,5V indicator.  Hsync Out,Vsync Out are the component part of Cysnc output，  5V indicator ： when“RGBout=car RGBin”, 5V indicator =0V ， NOTE：the RGB，AV1，AV2，CAM video on the input side are converted by internal circuit, while the CAR RGB input when“RGBout=navi RGBin,or AV1/2 in”， 5V indicator =5V [max.3A]。 is not, the car RGB is only switched to the RGB output leads.    When DIP sets the output to:” (off,off)： output=NTSC composite video” or ” (off,on)： output =PAL composite video” the RGB input/Output should not be used. When the user is switching the input[by set white wire to 12V or touch the “SRC” icon on touch panel], the input channel will be switched like this” navi RGBAV1AV2navi RGB…”, there is NO car RGB shown. When DIP sets the output to:” output =RGB-NTSC component video” the RGB input/Output can be used and CVBS output should not be used. When the user is switching the input[by set white wire to 12V or touch the “SRC” icon on touch panel], the input channel will be switched like this” CAR RGB navi RGBAV1AV2 CAR RGBnavi RGB…”, there is car RGB shown. When DIP sets the output to:” output =RGB-NTSC component video” the RGB input/Output can used and CVBS output should not be used. there is NO car RGB shown. 4.touch panel connector Touch panel connector This 8-pin connector is used to connect the touch daughter board, it is not necessary for the installers to use it usually, but it maight be helpful to the installers. Pin 1, Pin2 +5V output voltage for switch relay when AV1 is selected, 0V when AV2 selected. [max output=2A, while most mechanical relay only needs 0.1~0.3A.] Pin3: constant +5V when the unit is working. max 2A output. Pin 4,8 GND It is tied to GND inside. Pin 5: Pin 6: data bus for touch screen Pin5,6 should NOT be connected to GND, because it will halt the CPU inside. Leave it open for normal use. Pin 7 This pin=5V output voltage when in inserted video mode, when in original car video mode, this pin=0V. clock bus for touch screen. 5. key buttons The input box has 3 side keys, the installer may use it to tune the picture display, and touch function for the connected DVD or other devices. The 3 keys are : menu, +, -.  When menu key pressed 1st time: the left OSD options will be shown, when pressed 2nd time: the right OSD options will be shown, when pressed 3rd time, the osd window will disappear.  The user may use the +/- key to go to the edit mode of each item, and use menu-key again to go down to the next item.  The DVD, TUNER,NAVI items mean the IR output of RGB,AV1,AV2 input respectively, there are already many types of DVD, TV tuner and NAVI brands programmed inside. The installer may also set it to be “PROG” if the video source brand is not listed inside. Then he may pull the DIP6 DIP down to program the IR code. The installer may also set it to be “NONE” if he does not want the icons to pop out when people control it. In this case, the user may still touch the left-top corner[‘power’ icon] to tuner off the device, and he may also use the left-button corner, [‘SRC’ icon ] to switch the input.  The H POS, V POS items mean the image location on monitor, different video players like DVDs may send out video with different amplitude, different image location although it is PAL or NTSC. These 2 options will give the installer the convenience of adjusting image perfectly centered in a couple of seconds.  The ”Amplitude”is used to set the video output amplitude, a normal monitor needs 0.7V~1V for normal display on 75 ohm impedance monitor, but some needs higher[ for example BMW and Nissan which has sync on Green need 1.2Vpp for brilliant video display otherwise picture looks like washed]. Higher video amplitude is also better for noise immunity and more vivid display , but too much high amplitude(>80) is not  suggested. The default Amplitude =50, video output=1Vpp；whenAmplitude =80，video output=1.5Vpp； when Amplitude =10, video output=0.5Vpp. [ when monitor’s input impedance=75 ohm.]. The CAR VIDEO option is can be set to be “YES” or “NO”,  when set to “YES”, the CAR RGB or video input is shown when the user is switching the input. It is switching like this[when DIP78 set the output to be RGBS]: car RGB  converted RGB from AV1 converted RGB from AV2… car RGB Or [when DIP78 set the output to be CVBS]: car CVBSconverted CVBS from AV1 converted CVBS from AV2 car CVBS [note: when the Car RGB wires are used for CVBS, just connect the CVBS to the red wire, and leave G, B, and Sync alone.] when set to “NO”, the CAR RGB is never shown. This is for monitors which has already a RGB or CVBS input. They need such an interface for touch control onto DVD or Tuner. A. IR learn operations The input box has separate memory space to remember the IR code of every input[RGB input,AV1(DVD),AV2(Tuner or iPod)]. 1) When the current input channel’s IR output is set to “PROG”, the input box goes into IR learn mode when the DIP6 is pulled down to ‘ON’ state. 2) Then one icon will be blinking, saying that one IR key press is needed, the installer need to point the remote controller toward the whole on RGB input. 3) When one code is learned, another icon will be blinking, saying that another IR code is needed. The installer then repeating step 2), until all codes are programmed. Then the icons disappear automatically and the installer may start normal operation.  the touch screen will not acknowledge touch screen operations when it is in programming mode, except the ‘SRC’ key, which will terminate the learning progress. B. IR code out for video source devices The input box can output the IR code in a 4-byte protocol which most of AV devices use today, the output can be 2 ways: (1) wire connect way without carrier frequency, or (2) wireless way with carrier frequency. The difference is: the wireless way says the signal ‘1’ with 38K frequency pulses while the wire way says by just voltage. The input box has 2 IR output pins: IR-RGB(the 6th pin of RGB input), and IR_DVD(the 7th pin of RGB input). The IR_RGB is always in wire-connect way without carrier, while the IR-DVD pin is in a wireless way The IR_RGB and IR_DVD send the IR code out no matter the monitor is showing video in RGB,AV1,and AV2. The video source may receive all these IR codes, but they will choose to acknowledge because the data bytes values are different.[the 4 data bytes say the device by the first 2, and 3rd byte says the key value, the last one is the verification] C.Touch panel calibration When the DIP6 is pulled down to ‘ON’ 5 times repeatedly, the monitor goes into touch screen calibration mode, a cross will be shown on screen, and the installer need to use something like a pencil to hit the cross, the cross will be changed to another location after one point is recorded. This multi-point calibration should be done by the installer at least once, since all touch panels have different physical resistance and capacitance. The calibration guarantees the end-user have nice touch feelings. 6.Accessories a) b) c) d) e) 1PCs of video interface 1PC of touch toughter PCB. 1PC of 2X8 RGB wire, 1PC of video output wire. one Navi RGB input wire with IR transmitter diode. One 6Pin power wire. Navlinkz may also provide these accessories to help the installers： 2. 3. 4. 5. 6. 7. Flexible touch panel this touch panel offers no thickness, which is ideal for cars which has original LCD screen, because they do not offer extra space for touch screen. Video noise filter: Sometimes noise may be generated if the video devices are too much far away separated or engine noise influences, this noise filter can remove many kinds of video noises easily. 7. Parameters No. name parameter 1 RGB CVBS input amplitude Suggested 0.7Vpp with 75 ohm impedance Range: 0.3V~1V. 2 sync amplitude in RGB-navi port 3~5Vpp with 5K ohm impedance Sync should be NTSC composite with negative polarity. 3 RGB input resolution NTSC-RGB navigation, 320X240,400X240,480X240 [vertically some computer only output 234 line,it is also compatible ] 4 Av1,Av2, cam video input 0.7Vpp with 75 ohm impedance NTSC/PAL/SECAM automatic switch 5 CVBS RGB output amplitude 0.5V~2Vpp with 75 ohm impedance Video Amplitude set by OSD. When =50, output=1Vpp. Output :NTSC/PAL ,CVBS/RGB set by DIP 5 IR RGB, IR_AV1 output 3.3V digital infrared control code with 4 data bytes [machine code1,machine code 2, user code, verification code] 6 Normal Power consumption 2.4W [0.2A @12V] 7 Standby < 10uA (ACC=0V) 8 Reverse trigger threshold >5V trigger 9 Ctrl port Pin1,2 and Pin7: Output voltage Relay pull voltage for Audio and touch screen selection 5V volts. 10 Ctrl port Pin1,2 and Pin7: Current 2A. Tested to have no damage when short-circuit to GND for 2 minutes. Leave it open when do not use. 11 Work temperature -40 ~ +85C 12 Work voltage range 7V~35V on BATT and ACC. [Max.43V.] for normal use. Surge pulse: < 0.5s 0V~50 tested. current Application Examples: 1. Add touch control functions to DVD,TV and get free from remote controllers. Video in， video out IR out       Enable AV1 by DIP, if necessay, enable AV2 and navi RGB also to get some extra inputs. When power on, the unit will automatically go to the first DIP-enabled input.(AV1 here) The user may switch the input by touch the “SRC ” icon on screen. The CAR VIDEO option should be set to NO When DIP7 and 8 are both OFF, the output is NTSC-composite[no matter the input is PAL,NTSC or SECAM or RGB], the big internal memory tank and high quality scaler guarantees there is no picture quanlity decrease. When DIP7 is OFF and DIP8 is ON, the output is PAL composite. [no matter the input is PAL,NTSC or SECAM or RGB]. 2. Convert RGB high definition videos into composite（CVBS）video for monitors. RGBin， CVBS out IR Out     Enable RGB by DIP, if necessay, enable AV1 also to get one extra input. When power on, the unit will automatically go to the first DIP-enabled input.[navi-RGB here] When DIP7 and 8 are both OFF, the output is NTSC-composite[no matter the input is PAL,NTSC or SECAM or RGB], the big internal memory tank and high quality scaler guarantees there is no picture quanlity decrease. When DIP7 is OFF and DIP8 is ON, the output is PAL composite. When DIP4 is set to ON,the input is RGB-VGA from computer, that is （800X600·60Hz）, when the DIP4 is set to OFF, the input is RGB-NTSC for navi computer, which is vertically 240 lines(or 234 lines),horizontally 320,400,or 480 pixels. 3. Add extra video inputs to monitors which already has RGB input. For example: Volkswagen MFD2,Mercedes W211/W220, Toyota, Ford(before year 2010). This monitors already has RGB input.( atten: W211，W220 needs Hsync,Vsync split signals] Video in， RGB+sync out Or: RGB+ Hsync+Vsync IR out     DIP for AV1，AV2 are enabled by DIP, according to the video devices that are installed. DIP 7 and 8 should be set to (on,off)： output =RGB-NTSC component video. The CAR VIDEO option should be set to YES so when switching, the input are shown:car RGBAV1AV2 car RGB… if set to “NO”, the car video will not be shown. When DIP 7 and 8 are set to (on,off), the screen always starts at showing car RGB when start working. 4. Add extra video inputs to monitors which needs RGB input,but need sync on Green[that is SOG]. For example, BMW x5 before 2008, nissan 2010 and older versions, Renault, and American Pathfinder. Video in， RGB out IR     DIP for AV1，AV2 are enabled by DIP, according to the video devices that are installed. DIP 7 and 8 should be set to (on,off)： output =RGB-NTSC component video. when switching, the input are shown:car RGBAV1AV2 car RGB The Green signal output wire should be re-wired to the 2-pin Jack near the RGB-wires, that one always has sync on green. the screen always starts at showing car RGB when start working. 5. Add DVD,TV tuner or other video devices with touch control function for Mercedes W212, Citroen-C5, Audi-MMI,Buick/Opel, and many other cars which has already a monitor. NAVLINKZ has video interfaces for these car, they have internal touch icon generations already, in this case, the installers just put one extra touch film on top of the screen, and they can use the interface to control DVD or other video sources. Almost all Navlinkz’s interface use CAN bus decoding and GMLAN decoding, so the the users do not need to stick any extra key to switch,people use original keys to switch, and they may also use origianl keys to pop out the DVD touch icons. The installers can also use the touch interface between the video source and interface, using the touch interface’s video-in-video-out function and get the touch function for extra video device.