Transcript
TOUCHLESS FAUCET INSTALLATION GUIDE Before installing, read the entire touchless faucet installation guide. Observe all local building and safety codes. For the following installation instructions for your new faucet it is assumed that any old fixtures have been removed and any repairs or modifications to the water supply have been completed. Unpack and inspect the product for any shipping damages. If you find damages, do not install. Contact Customer Service at 1-866-855-2284. If you need assistance or have questions while installing your touchless faucet, contact Customer Service. We recommend consulting a professional if you are unfamiliar with installing kitchen fixtures. Signature Hardware accepts no liability for any damage to the counter top, walls, plumbing or for personal injury during installation. Turn off the water supply at the sink where the new faucet is being installed.
PRODUCT PERFORMANCE INDEX Power Supply
DC 3 V (2pcs)
Power Consumption
DC: ≤ 0.5 mW
Sensor Range
Upper Sensor Window: 5"-7" Lower Sensor Window: Set automatically according to basin depth within 6 seconds of powering on
Working Pressure
0.05MPa-0.6MPa
Working Temperature
39°F-140°F
Touchless Faucet Installation Guide
1
Upper Sensor Window Lower Sensor Window
PARTS LIST Component
Qty
1.
Faucet Body
1
2.
Gasket A
1
3.
Plastic Gasket
1
4.
Gasket B
1
5.
Clamping Ring
1
6.
Nut
1
7.
Bolt
2
8.
Water Supply Tube
2
9.
Compression Nut
2
10. Control Box Connector
1
11. DC Control Box
1
12. Control Box Support
1
Touchless Faucet Installation Guide
2
INSTALLATION
1. Loosen the bolts (7) to remove the, nut (6), clamping ring (5), gasket B (4), and plastic gasket (3) from the faucet body (1).
2. Connect the water supply tube (8) and control box connector (10) to the faucet body (1). Insert the bottom portion of the faucet through the hole in the counter top. From beneath the counter, thread the plastic gasket (3), gasket B (4), and clamping ring (5), onto the faucet body.
3. Thread the nut (6) onto the faucet body and tighten the bolts (7) to secure.
4. Attach the control box support to the wall beneath the counter.
Touchless Faucet Installation Guide
3
5. Connect the control box connector (10), sensor line, and nylon hose to the DC control box as pictured. Attach the control box to the box support.
6. Connect the water supply tubes to the main water supply with the compression nuts (9).
TO REPLACE BATTERIES 1. Loosen the bolts to remove the battery cover plate. 2. Insert two 3V D batteries as pictured. 3. Replace the cover plate and water proof rubber seal, and fasten the bolts to secure.
Touchless Faucet Installation Guide
4
OPERATING INSTRUCTIONS Handle: • •
Pull the handle away from the faucet to tum ON; operate reversely to tum OFF. Push backward for cold water, pull forward for hot water.
Upper Sensor Window: •
Place hands in front of the sensor window to turn the water on. The water will shut off automatically after 30 seconds. To turn the water off, place hands in front of the sensor window again within 30 seconds.
Lower Sensor Window: •
Place hands in front of the sensor window to turn the water on. The water will shut off immediately after moving hands away from sensor. Water off immediately Lower Sensor Window
Touchless Faucet Installation Guide
5
TROUBLESHOOTING Problem
Possible Cause
Solution
Power exhausted
Replace battery
Water will not stop Water pressure out of range flowing:
There is no water flowing:
Refer to product performance index
Filter blocked
Clean water inlet filter
Power exhausted
Replace battery
Water supply cut off
Test water supply
Filter blocked
Clean water inlet filter
Dirty sensor window
Wipe window with wet cloth
Low water pressure
Refer to product performance index
Filter blocked
Clean water inlet filter
Low water pressure
Refer to product performance index
Filter blocked
Clean water inlet filter
Poor battery
Replace with new battery
There is a leak:
Low water flow:
Short battery life:
Touchless Faucet Installation Guide
6
