Preview only show first 10 pages with watermark. For full document please download

Tpm Product Type 107-d126-nnt 16-channel Digital Input And 48

   EMBED


Share

Transcript

TPM Product quick start guide Product Type 107-D126-NNT 16-channel digital input and 48-channel digital output module with pluggable terminal Specifications Size: (L122 x W123 x H104 mm) Series Interface: Half duplex RS-485 with transformer isolation Cable Type: CAT5 UTP/STP Ethernet Cable Surge Protection: 10KV Transfer Rate: 2.5Mbps, 5Mbps, 10Mbps, 20Mbps IO Isolation Voltage: 2.5KVrms Input impedance: 5.6KΩ/0.5W. Input current: ±5mA (Max) Output Types: NPN open collector Darlington transistors Switch Capacity: each output channel is 350mA/channel maximum at 24V DC Response Time: On to Off about 50μs, Off to On about 8μs Over Current Protection: 3A (max) for each port (8-channel) Input Voltage: +18V DC ~ +30V DC. Power Consumption: 6W typical Working Temperature: 0 ~ 60°C Ordering Information 107-D126-NN – 16-channel digital input with NPN and 48-channel digital output with NPN IO interface Label Function CN1 Motionnet Communication Control Connector CN2 Motionnet Communication Control Connector R_CN3 Power Connector L_CN3 Power Connector R_CN5 I/O Signal Connector L_CN5 I/O Signal Connector R_CN6 I/O Signal Connector L_CN6 I/O Signal Connector R_CN7 I/O Signal Connector L_CN7 I/O Signal Connector R_CN8 I/O Signal Connector L_CN8 I/O Signal Connector 1 TPM LED Description Product quick start guide 00 01 02 03 00 03 04 07 10 13 14 17 20 23 24 27 30 33 34 37 PORT#0 PORT#1 04 05 06 07 Disp Label Disp Label Disp Label 00 Port#0 Bit0 14 Port#1 Bit4 30 Port#3 Bit0 01 Port#0 Bit1 15 Port#1 Bit5 31 Port#3 Bit1 02 Port#0 Bit2 16 Port#1 Bit6 32 Port#3 Bit2 03 Port#0 Bit3 17 Port#1 Bit7 33 Port#3 Bit3 04 Port#0 Bit4 20 Port#2 Bit0 34 Port#3 Bit4 05 Port#0 Bit5 21 Port#2 Bit1 35 Port#3 Bit5 06 Port#0 Bit6 22 Port#2 Bit2 36 Port#3 Bit6 07 Port#0 Bit7 23 Port#2 Bit3 37 Port#3 Bit7 10 Port#1 Bit0 24 Port#2 Bit4 P0 DC 24V 11 Port#1 Bit1 25 Port#2 Bit5 P1 DC 5V 12 Port#1 Bit2 26 Port#2 Bit6 R RUN 13 Port#1 Bit3 27 Port#2 Bit7 E ERROR PORT#2 PORT#3 P 0P1 R E Connector Reference  Motionnet communication control connector  Pin Label Function 1 NC Reserved 2 NC Reserved 3 D+ Differential D+ signal 4 NC Reserved 5 NC Reserved 6 D- Differential D- signal 7 NC Reserved 8 NC Reserved Pin Label 1 24V DC 24V 2 GND DC 24V ground 3 FG Power connector Function Field ground 2 TPM  I/O control connector Product quick start guide R_CN5 R_CN6 Pin Label Function 1 In_00 Port#0 Bit0 Input 1 In_10 Port#0 Bit0 Input 2 In_01 Port#0 Bit1 Input 2 In_11 Port#0 Bit1 Input 3 24V +24V Power Input 3 24V +24V Power Input 4 GND 24V Ground Input 4 GND 24V Ground Input 5 In_02 Port#0 Bit2 Input 5 In_12 Port#0 Bit2 Input 6 In_03 Port#0 Bit3 Input 6 In_13 Port#0 Bit3 Input 7 In_04 Port#0 Bit4 Input 7 In_14 Port#0 Bit4 Input 8 In_05 Port#0 Bit5 Input 8 In_15 Port#0 Bit5 Input 9 24V +24V Power Input 9 24V +24V Power Input 10 GND 24V Ground Input 10 GND 24V Ground Input 11 In_06 Port#0 Bit6 Input 11 In_16 Port#0 Bit6 Input 12 In_07 Port#0 Bit7 Input 12 In_17 Port#0 Bit7 Input Pin Label R_CN8 R_CN7 Pin Label Function Function Pin Label Function 1 Out_20 Port#0 Bit0 Output 1 Out_30 Port#0 Bit0 Output 2 Out_21 Port#0 Bit1 Output 2 Out_31 Port#0 Bit1 Output 3 24V +24V Power Input 3 24V +24V Power Input 4 GND 24V Ground Input 4 GND 24V Ground Input 5 Out_22 Port#0 Bit2 Output 5 Out_32 Port#0 Bit2 Output 6 Out_23 Port#0 Bit3 Output 6 Out_33 Port#0 Bit3 Output 7 Out_24 Port#0 Bit4 Output 7 Out_34 Port#0 Bit4 Output 8 Out_25 Port#0 Bit5 Output 8 Out_35 Port#0 Bit5 Output 9 24V +24V Power Input 9 24V +24V Power Input 10 GND 24V Ground Input 10 GND 24V Ground Input 11 Out_26 Port#0 Bit6 Output 11 Out_36 Port#0 Bit6 Output 12 Out_27 Port#0 Bit7 Output 12 Out_37 Port#0 Bit7 Output 3 TPM  I/O control connector Product quick start guide L_CN5 Pin Label Function L_CN6 Pin Label Function 1 Out_00 Port#0 Bit0 Output 1 Out_10 Port#0 Bit0 Output 2 Out_01 Port#0 Bit1 Output 2 Out_11 Port#0 Bit1 Output 3 24V +24V Power Input 3 24V +24V Power Input 4 GND 24V Ground Input 4 GND 24V Ground Input 5 Out_02 Port#0 Bit2 Output 5 Out_12 Port#0 Bit2 Output 6 Out_03 Port#0 Bit3 Output 6 Out_13 Port#0 Bit3 Output 7 Out_04 Port#0 Bit4 Output 7 Out_14 Port#0 Bit4 Output 8 Out_05 Port#0 Bit5 Output 8 Out_15 Port#0 Bit5 Output 9 24V +24V Power Input 9 24V +24V Power Input 10 GND 24V Ground Input 10 GND 24V Ground Input 11 Out_06 Port#0 Bit6 Output 11 Out_16 Port#0 Bit6 Output 12 Out_07 Port#0 Bit7 Output 12 Out_17 Port#0 Bit7 Output L_CN7 Pin Label Function L_CN8 Pin Label Function 1 Out_20 Port#0 Bit0 Output 1 Out_30 Port#0 Bit0 Output 2 Out_21 Port#0 Bit1 Output 2 Out_31 Port#0 Bit1 Output 3 24V +24V Power Input 3 24V +24V Power Input 4 GND 24V Ground Input 4 GND 24V Ground Input 5 Out_22 Port#0 Bit2 Output 5 Out_32 Port#0 Bit2 Output 6 Out_23 Port#0 Bit3 Output 6 Out_33 Port#0 Bit3 Output 7 Out_24 Port#0 Bit4 Output 7 Out_34 Port#0 Bit4 Output 8 Out_25 Port#0 Bit5 Output 8 Out_35 Port#0 Bit5 Output 9 24V +24V Power Input 9 24V +24V Power Input 10 GND 24V Ground Input 10 GND 24V Ground Input 11 Out_26 Port#0 Bit6 Output 11 Out_36 Port#0 Bit6 Output 12 Out_27 Port#0 Bit7 Output 12 Out_37 Port#0 Bit7 Output 4 TPM  SW1: node number setting Product quick start guide Pin Label On Off 1 A5 1 0 2 A4 1 0 3 A3 1 0 1 2 3 4 5 6 4 A2 1 0 SW1 5 A1 1 0 6 A0 1 0 3 4 5 1 2 6 3 4 5 B1 B0 TD TM BK 2 A5 A4 A3 A2 A1 A0 1 S W2 SW1 N Note that node number = 32 x A5+16 x A4+8 x A3+4 x A2+2 x A1+A0. Default values are all off.  SW2: function setting Pin Label 1 B0 2 Description On Off *Baud-Rate Setting 1 0 B1 *Baud-Rate Setting 1 0 3 TD Time-Out Status Latch Enable Disable 4 TM Watch Dog Mode Enable Disable 5 TR Termination Resistance Enable Disable N 1 2 3 4 5 4 5 6 1 2 3 4 5 TM BK 3 B1 B0 TD 2 A5 A4 A3 A2 A1 A0 1 S W2 SW1 SW2 The table below shows the settings of transfer rates. Default value is 10Mbps. N 1 2 3 4 5 6 Default Setting B0 B1 Transfer rate OFF OFF 20Mbps ON OFF 10Mbps OFF ON 5Mbps ON ON 2.5Mbps Output Signal Circuit  NPN Input Signal Circuit  NPN +24V Relay_1NO Output Signal I < 350mA +24V 5.6K Input Signal R > 1.2K GND Internal Circuit GND Internal Circuit 5 TPM Product quick start guide RS-485 Terminal Resistance When you use 107-D1xx series Module as the last one in Motionnet Ring, it is necessary to put RS-485 terminate resistance on the RJ-45 connector (CN2). Since 2016.07.01, 107-D1xx series has built in TR function, so you could turn on TR to replace RJ-45 terminate resistance Notice It is necessary to attach two EZM-D1xx modules on this terminal to ensure the Motionnet communication. 6