Travla Enclosure Chassis Te-1160 Quick Installation Guide Top

Transcript

Travla Enclosure Chassis TE-1160 Quick Installation Guide Note: These items are not included in this package. 1. Mainboard 2. Hard Disk 3. RAM 4. Optical Drive 5. Compact flash module 5) Install SATA HDD to HDD Tray 4) Slide HDD Tray #6-32 5mm flat head screw (x4) SATA HDD B HD TRAY B B 1 - Slide HDD TRAY. 1 - Secure flat head screw (x4) from under. 6) Remove Optical Driver Cover 7) Install Slim Type Optical Drive(optional) M2x3mm I head screw (x2) M3x5mm flat head screw (x2) Warning B Install and service to this product is performed by qualified personnel to avoid risk of injuries Front Panel Optional Compact Flash Slot Optional Optical Drive Bay D D IOIO Mic Power LED HDD LED Audio USB 2.0 E E Optical Driver Cover Slim Type Optical Drive 1 - Remove flat head screw (x2). 2 - Remove optical drive cover. HDD TRAY(x4) Power Switch Distribue par Anteor - www.anteor.com - Tel : 01 61 37 07 00 Back Panel 1 - Install slim type optical drive 2 - Secure I head screw (x2) on left side. 8) Install Compact Flash (optional) Rear side of Mainboard I/O PCI Slots(x2) 9) Install Dual-PCI Riser Card Power Supply M3x5mm hex head screw (x2) C M3x5mm hex head screw (x4) C Air flow hole C C C Screw Identification Guide #6-32 5mm flat head screw (B) A D M3x5mm flat head screw C Compact Flash Dual-PCI Riser Card #6-32 5mm flat head screw M3x5mm hex head screw B E M2x3mm I head screw C 10) Install Mainboard into Chassis 1) Remove Top Cover C M3x5mm hex head screw (x4) A A C C #6-32 5mm flat head screw (B) (x5) Top cover Top cover A 1 - Attach Dual-PCI Riser Card to the holder. 2 - Secure hex head screw (x4). 1 - Install Compact Flash with hex head screw (x2). C A A Mainboard 1 - Remove flat head screw (x5). 2 - Slide top cover to rear. 2) Remove 2.5HD Bracket 3) Install 2.5-inch HDD to Bracket M3x5mm hex head screw (x4) M3x5mm hex head screw (x2) 1 - Place Mainboard to 1U chassis with the right I/O gasket. 2 - Secure hex head screw (x4). Safety Cautions SAFETY STEPS: When removing the chassis cover to access the system components, follow the safety precautions below: C C C C Bracket 1 - Remove hex head screw (x2). 2 - Remove 2.5HD bracket (x2). C Bracket C 1 - Insert HDD to the bracket as shown. 2 - Secure HDD with hex head screw (x4). 1. Turn off all peripheral devices connected to the system. 2. Turn off the system by pressing the power button. 3. Unplug all AC power cords from the system or from wall outlets. 4. Label and disconnect all cables connected to I/O connectors or ports on the back of the system. 5. Wear an antistatic wrist strap grounded to the chassis -- any unpainted metal surface -- when handling components. 6. Do not turn on the system when the chassis cover is open. The microprocessor and heatsink may be hot if the system has been running. Also, there may be sharp pins and edges on some board and chassis parts. Contact should be made with care. Consider wearing protective gloves. Travla TE-T1160 Quick Installation Guide