Transcript
Trenton Hall Annex ‐ Allied Health ‐ Plebotomy Lab
Trenton Hall Annex ‐ Allied Health ‐ Optometry (2 labs) Qty
Component 1 Media connector plate
Manufacturer Extron
1 Connector plate with Extron HDMI, VGA, 3.5mm audio and USB connectors. 1 RJ‐45 Network barrel Extron connectors 1 Digital Document Samsung Camera 1 8 outlet Power strip Tripp Lite
Model Cable Cubby ‐ Model #1200 (part no. 60‐1397‐ 02) AAP Super Plate 100 (part no. 70‐1076‐02)
Location Instructor Table
Installed in Cable Cubby.
AAP RJ‐45 (part no. 70‐ Installed in Cable 491‐11) Cubby. SDP‐960 Instructor Table
PS2408
Instructor Table
Function Access point for instructor to connect laptop, document camera and other devices to ceiling mounted projector. Provides connections to LCD projector for digital document camera/laptop, laptop audio, HDMI components and easy USB connection to instructor PC.
Note: All compiled and uncompiled Touch Screen programming will be provided to MCCC upon completion of testing/acceptance of systems. Component 1 Media controller
1 Audio Amplifier 1 Volume control modules 2 Speakers
Manufacturer Extron
Extron Extron
MPA 152+ MLA VC 10 Plus
Extron
FF 220T (wired for 8 ohm) ECB2SP‐CR
1 Plenum Wiremold box/projector ceiling mount for audio amplifiers 1 LCD Projector mount Peerless
1 Extension pipe
Model MLC 226 IP ‐ L
Extron
1 Recess mounted tab‐ Da‐lite tensioned projection screens w/wall mounted switch and low voltage control
Note: All cables from the instructor lectern to the projectors/audio system (video, audio, control, network, electric) must be able to be disconnected in a floor box located under the lectern location. Recommended floor box size is 12" x 12" x 8". RapidRun cables are to utilize standard RapidRun connections. A custom bulkhead panel accomodating all connections will need to be installed the box. Qty
Cable Type
Manufacturer
1 Digital runner Cables To Go w/flying leads (1 active, 1 passive) 2 Analog runner Cables To Go w/flying leads (VGA w/3.5mm audio) Bulk 16 gauge Beldin speaker/control wire
Location Rapid Run ‐ Digital
Rapid Run ‐ Analog
1 control cable
Beldin
Cat 5e
1 control cable
Beldin
Cat 5e
1 Cat 5e cable
Beldin
Cat 5e
1 Cat 5e cable
Beldin
1 Audio cable
3.5mm M‐M
1 18‐3 control cable
Beldin
1 RJ‐45 to DB‐9 Adapter
Cables to Go
3 wire to 3.5mm M
Function
From MLM‐WB+ to For HDMI signals (projector end of cable Plenum box/LCD requires Active Flying Lead) to LCD projector projectors (2) From MLM‐WB+ to For VGA Plenum box/LCD projector From audio amplifier in (Cable Cubby) to Plenum box/LCD plenum boxs to each projector speaker/From MLA VC 10 + to MPA 152 + From Extron MLC 226 IP‐ Controls raising and lowering of L Media Controller to projection screen. low voltage control of projection screen RS‐232 control of projector From Extron Media Controller to LCD Projector MLC 226 IP‐L Remote monitoring/control connection to network From MLC 226 IP to MLA Volume control VC 10+ From LCD projector to Program audio for room MPA 152+ From MLC 226 IP ‐ L to RS‐232‐C input switching control of Document Camera document camera. Mounted to projector Communication/control of projector by RS‐232 port Extron MediaLink controller.
Notes: The PC is to be mounted under the instructor table. Cable Cubby #1 will provide electric for the PC monitor and a pass through plate for the monitor cable and USB connectors for keyboard, mouse and USB flash drives. Cable Cubby #2 will provide a VGA connection for the document camera/laptop (switched by document camera); an audio connection for the laptop, electric for the document camera/laptop or an instructor provided device and and HDMI connection. Electrical needs: Cable Cubby (2 outlets) Instructor PC (2 outlets ‐ PC and Monitor) Auxiliary outlets (power strip mounted to bottom or side of instructor table)
Model Cable Cubby ‐ Model #1200 (part no. 60‐1397‐ 02) AAP Super Plate 100 (part no. 70‐1076‐02)
Location Instructor Table
Installed in Cable Cubby.
AAP RJ‐45 (part no. 70‐ Installed in Cable 491‐11) Cubby. SDP‐960 Instructor Table
PS2408
Instructor Table
Function Access point for instructor to connect laptop, document camera and other devices to ceiling mounted projector. Provides connections to LCD projector for digital document camera/laptop, laptop audio, HDMI components and easy USB connection to instructor PC.
Qty
Component 1 Media connector plate
Manufacturer Extron
1 Connector plate with Extron HDMI, VGA, 3.5mm audio and USB connectors. 1 RJ‐45 Network barrel Extron connectors 1 Digital Document Samsung Camera
Display of documents/images and switch for auxilary VGA devices (ie. Laptops, etc.) Access to power for devices
1 8 outlet Power strip Tripp Lite
Model Cable Cubby ‐ Model #1200 (part no. 60‐1397‐ 02) AAP Super Plate 100 (part no. 70‐1076‐02)
Location Instructor Table
Installed in Cable Cubby.
AAP RJ‐45 (part no. 70‐ Installed in Cable 491‐11) Cubby. SDP‐960 Instructor Table
PS2408
Instructor Table
Function Access point for instructor to connect laptop, document camera and other devices to ceiling mounted projector. Provides connections to LCD projector for digital document camera/laptop, laptop audio, HDMI components and easy USB connection to instructor PC.
Display of documents/images and switch for auxilary VGA devices (ie. Laptops, etc.) Access to power for devices
Media Control Components
Media Control Components
Note: All compiled and uncompiled Touch Screen programming will be provided to MCCC upon completion of testing/acceptance of systems.
Note: All compiled and uncompiled Touch Screen programming will be provided to MCCC upon completion of testing/acceptance of systems.
Qty
Qty
Component 1 Media controller
Manufacturer Extron
Model MLC 226 IP
Location Wall near instructor table
1 Audio Amplifier 1 Volume control modules 2 Speakers
Extron Extron
MPA 152+ MLA VC 10 Plus
Projector plenum box Media wall box
Extron
FF 220T (wired for 8 ohm) ECB2SP‐CR
Ceiling (fits in 2' x 2' grid) In drop ceiling area
Wiremold 1 Plenum box/projector ceiling mount for audio amplifiers 1 LCD Projector mount Peerless
PRG‐UNV
Cables
Manufacturer Extron
1 8 outlet Power strip Tripp Lite
Location Function Installed in UCM‐RAAP Provide control of projector inputs, projection screens, volume levels. Installed in wall near instructor. Projector plenum box For Program Audio and Voice Lift Audio Projector plenum box Separate volume control of audio amplifiers for voice and program Ceiling (fits in 2' x 2' 6 for program audio, 6 for voice system grid) In drop ceiling area Above ceiling projector mount and housing of electrical power for projector and audio amplifier.
Attaches projector to All cabling to projectors is run through ceiling mounting plate the above ceiling mounting plate/plenum box and this mount. PMP* Length to be determined so that the LCD projector aligns with the top of the projection screen. All cabling to the projector is to be routed through the PMP. Boardroom Electrol At designated location Low voltage control to interface with Wide Format 60" x 96" in the front of the Extron controls. Wall mounted switch matte screen with a classroom. (standard voltage) also required in case minimum 12" black of system failure. drop* (Note: Black drop may be more based on ceiling height at location and the top of the projection surface being 8' above finished floor)
Component 1 Media connector plate
1 Connector plate with Extron HDMI, VGA, 3.5mm audio and USB connectors. 1 RJ‐45 Network barrel Extron connectors 1 Digital Document Samsung Camera
Display of documents/images and switch for auxilary VGA devices (ie. Laptops, etc.) Access to power for devices
Media Control Components
Qty
Qty
Trenton Hall Annex ‐ Allied Health ‐ 2nd floor classroom
1 Extension pipe
Extron
1 Recess mounted tab‐ Da‐lite tensioned projection screens w/wall mounted switch and low voltage control
Function Provide control of projector inputs, projection screens, volume levels. Installed in wall near instructor. For Program Audio and Voice Lift Audio Separate volume control of audio amplifiers for voice and program 6 for program audio, 6 for voice system Above ceiling projector mount and housing of electrical power for projector and audio amplifier.
Component 1 Media controller
Manufacturer Extron
Model MLC 226 IP
Location Wall near instructor table
1 Audio Amplifier 1 Volume control modules 2 Speakers
Extron Extron
MPA 152+ MLA VC 10 Plus
Projector plenum box Media wall box
Extron
FF 220T (wired for 8 ohm) ECB2SP‐CR
Ceiling (fits in 2' x 2' grid) In drop ceiling area
Wiremold 1 Plenum box/projector ceiling mount for audio amplifiers 1 LCD Projector mount Peerless
PRG‐UNV
Attaches projector to All cabling to projectors is run through ceiling mounting plate the above ceiling mounting plate/plenum box and this mount. PMP* Length to be determined so that the LCD projector aligns with the top of the projection screen. All cabling to the projector is to be routed through the PMP. Boardroom Electrol At designated location Low voltage control to interface with Wide Format 60" x 96" in the front of the Extron controls. Wall mounted switch matte screen with a classroom. (standard voltage) also required in case minimum 12" black of system failure. drop* (Note: Black drop may be more based on ceiling height at location and the top of the projection surface being 8' above finished floor)
1 Extension pipe
Extron
1 Recess mounted tab‐ Da‐lite tensioned projection screens w/wall mounted switch and low voltage control
Function Provide control of projector inputs, projection screens, volume levels. Installed in wall near instructor. For Program Audio and Voice Lift Audio Separate volume control of audio amplifiers for voice and program 6 for program audio, 6 for voice system Above ceiling projector mount and housing of electrical power for projector and audio amplifier.
PRG‐UNV
Attaches projector to All cabling to projectors is run through ceiling mounting plate the above ceiling mounting plate/plenum box and this mount. PMP* Length to be determined so that the LCD projector aligns with the top of the projection screen. All cabling to the projector is to be routed through the PMP. Boardroom Electrol At designated location Low voltage control to interface with Wide Format 60" x 96" in the front of the Extron controls. Wall mounted switch matte screen with a (standard voltage) also required in case classroom. minimum 12" black of system failure. drop* (Note: Black drop may be more based on ceiling height at location and the top of the projection surface being 8' above finished floor)
Cables
Cables
Note: All cables from the instructor lectern to the projectors/audio system (video, audio, control, network, electric) must be able to be disconnected in a floor box located under the lectern location. Recommended floor box size is 12" x 12" x 8". RapidRun cables are to utilize standard RapidRun connections. A custom bulkhead panel accomodating all connections will need to be installed the box.
Note: All cables from the instructor lectern to the projectors/audio system (video, audio, control, network, electric) must be able to be disconnected in a floor box located under the lectern location. Recommended floor box size is 12" x 12" x 8". RapidRun cables are to utilize standard RapidRun connections. A custom bulkhead panel accomodating all connections will need to be installed the box.
Qty
Cable Type
Manufacturer
Location
Cables To Go
Rapid Run ‐ Digital
Cables To Go 2 Analog runner w/flying leads (VGA w/3.5mm audio)
Rapid Run ‐ Analog
1 Digital runner w/flying leads (1 active, 1 passive)
Beldin Bulk 16 gauge speaker/control wire
1 control cable
Beldin
Cat 5e
1 control cable
Beldin
Cat 5e
1 Cat 5e cable
Beldin
Cat 5e
1 Cat 5e cable
Beldin
1 Audio cable
3.5mm M‐M
1 18‐3 control cable
Beldin
1 RJ‐45 to DB‐9 Adapter
Cables to Go
3 wire to 3.5mm M
Function
From Instructor Table For HDMI signals (projector end of cable (Cable Cubby) to requires Active Flying Lead) to LCD Plenum box/LCD projectors (2) projector From Instructor Table For VGA (Cable Cubby) to Plenum box/LCD projector From audio amplifier in (Cable Cubby) to Plenum box/LCD plenum boxs to each projector speaker/From MLA VC 10 + to MPA 152 + From Extron MLC 226 IP Controls raising and lowering of Media Controller to projection screen. low voltage control of projection screen From Extron Media RS‐232 control of projector Controller to LCD Projector MLC 226 IP connection Remote monitoring/control to network From MLC 226 IP to MLA Volume control VC 10+ From LCD projector to Program audio for room MPA 152+ RS‐232‐C input switching control of From MLC 226 IP to Document Camera document camera. Mounted to projector Communication/control of projector by RS‐232 port Extron MediaLink controller.
Notes: The PC is to be mounted under the instructor table. Cable Cubby #1 will provide electric for the PC monitor and a pass through plate for the monitor cable and USB connectors for keyboard, mouse and USB flash drives. Cable Cubby #2 will provide a VGA connection for the document camera/laptop (switched by document camera); an audio connection for the laptop, electric for the document camera/laptop or an instructor provided device and and HDMI connection. Electrical needs: Cable Cubby (2 outlets) Instructor PC (2 outlets ‐ PC and Monitor) Auxiliary outlets (power strip mounted to bottom or side of instructor table)
Qty
Cable Type
Manufacturer
Location
Cables To Go
Rapid Run ‐ Digital
Cables To Go 2 Analog runner w/flying leads (VGA w/3.5mm audio)
Rapid Run ‐ Analog
1 Digital runner w/flying leads (1 active, 1 passive)
Bulk 16 gauge Beldin speaker/control wire
1 control cable
Beldin
Cat 5e
1 control cable
Beldin
Cat 5e
1 Cat 5e cable
Beldin
Cat 5e
1 Cat 5e cable
Beldin
1 Audio cable
3.5mm M‐M
1 18‐3 control cable
Beldin
1 RJ‐45 to DB‐9 Adapter
Cables to Go
3 wire to 3.5mm M
Function
From Instructor Table For HDMI signals (projector end of cable (Cable Cubby) to requires Active Flying Lead) to LCD Plenum box/LCD projectors (2) projector From Instructor Table For VGA (Cable Cubby) to Plenum box/LCD projector From audio amplifier in (Cable Cubby) to Plenum box/LCD plenum boxs to each projector speaker/From MLA VC 10 + to MPA 152 + From Extron MLC 226 IP Controls raising and lowering of Media Controller to projection screen. low voltage control of projection screen From Extron Media RS‐232 control of projector Controller to LCD Projector MLC 226 IP connection Remote monitoring/control to network From MLC 226 IP to MLA Volume control VC 10+ From LCD projector to Program audio for room MPA 152+ RS‐232‐C input switching control of From MLC 226 IP to Document Camera document camera. Mounted to projector Communication/control of projector by RS‐232 port Extron MediaLink controller.
Notes: The PC is to be mounted under the instructor table. Cable Cubby #1 will provide electric for the PC monitor and a pass through plate for the monitor cable and USB connectors for keyboard, mouse and USB flash drives. Cable Cubby #2 will provide a VGA connection for the document camera/laptop (switched by document camera); an audio connection for the laptop, electric for the document camera/laptop or an instructor provided device and and HDMI connection. Electrical needs: Cable Cubby (2 outlets) Instructor PC (2 outlets ‐ PC and Monitor) Auxiliary outlets (power strip mounted to bottom or side of instructor table)
