Transcript
PRODUCT INFORMATION SHEET Triam 44 Spray Gun 410-10, 410-10A, 410-11
Product Name Product Code(s)
REV01-07
These Triam spray guns are ideal for most spaying applications & are recommended for professional use. It is made with a sturdy stainless steel/brass barrel, & polypropylene handle & trigger mechanism. It has a trigger controlled spray pattern. The trigger that can also be locked in any spray pattern adjustable from a wide cone to a straight stream to help reduce fatigue (on 410-12 and 410-11), therefore an adjustable nozzle is not required Hose swivel, cone and fan nozzles are provided There are 300mm & 500mm barrel length options, & one with an adjustable brass nozzle fitted
Specifications
Materials:
Weight: Length:
50 bar / 725 PSI
High resistance plastic materials Stainless steel Brass NBR gaskets ch 24 hose shank 660 g / 23 oz ( 300 mm ) 890 g / 31.5 oz ( 600 mm ) 300 mm / 11.7" - 600 mm / 23.6"
Nozzle: Standard AMT ceramic spray tip ø1.5 + ø10 mm Max. spray tip hole:
ø2.3 mm
Frequently Asked Questions
Use: Agricultural, horticultural and floricultural spraying. "Spot" spraying, including Blackberries Spray pattern adjust; via trigger lock Drip free shut off.
Q: What is a ‘trigger controlled spray pattern”? A: the trigger can be preset, so you don’t have to hold the trigger while operating the gun, therefore reducing fatugue Q: How do I set the Spray pattern? A: Squeeze trigger & adjust ring nuts (18 & 22) so they hold trigger at desired Spray pattern & release trigger Q: Can I use this gun on LOW Pressure (eg. 12v Pumps)? A: Yes, it will still work efficiently, but due to lower flow rates, ensure the nozzle to suits your application Q: Why does my gun leak from the nozzle? A: The main seat (2) is worn/damaged & needs replacement NOTE: It is also suggested to change nozzle at this stage
Component Identification
Max. Operating pressure:
How it works
Product Features & General Use
Revision
Fluid comes from Pump via inlet by trigger (9 or 12). Seat to stop fluid is by nozzle, which ensures minimal dripping when turned off. Spray pattern is operated via lockable adjustable trigger. Fluid is rotated before nozzle (5) to ensure a tidy efficient spray pattern is achieved.
Triam 44 – Spray Pistols Part numbers: 410-11 , 410-11A , 410-12 To Service: Gun that is leaking from nozzle area Unscrew Front Body (3) from Barrel (6). First, check Thick Flat O-ring (2) for ANY damage & replace as required – this is the main seal. Ensure that the back edge of Green Spindle Fins (5) should be level with end of (6). To adjust; Wedge a screwdriver between Nut (21) & Handle (26) & turn spindle (5). If required, Hook gun to a garden hose on mains water for testing.
To Service: Trigger not operating correctly Ensure FRONT Ring Nut (18) is screwed up completely (clockwise) towards the nozzle Adjust REAR Ring Nut (22) to set spray pattern for when trigger is pulled.
To Remove & Replace Green Spindle Fins (5); Remove Nozzle Assembly (1,2,3,4) – check (2) for damage, & replace as required Take out trigger pin & slide out trigger. Loosen & remove 7mm Nut (21) from under trigger (hold green spindle). Remove (22,23,24) – Check spring & lube. Pull spindle & shaft out from nozzle end as one piece - may need to use pliers for leverage Lube new spindle/shaft & push in. Replace (20) & (21) Screw on (23), tighten (21) against (23) To relocate handle, push spindle in to shaft to make more space between (18,22) for ease of fitment Ensure (20) is at rear of handle slot Note: Adjust (21) to align rear of (5) with end of barrel
Other checks while unit is apart; Check there are no sharp edges on barrel that may cause damage to (4) or (2) Check (4) & (2) for damage & lube to prevent leaking. The front end nipple of (5) should protrude approx 2.5 to 3mm from (3) – see below. If not, (5) may be binding inside (3) & will need to be lightly reamed. This can also cause trigger to become sticky. To Fix: Remove 3, invert & check that it slides freely on Spindle (5), if NOT, ream inside of 3 & clean outside of 5, until they move freely
5 3
LEAKING Nozzle? Replace the THICK NOZZLE GASKET (4.9mm) that comes with the gun. The thick gasket (product code: 401-35-601-35) suits red plastic nozzle supplied in kit (Nozzle: DVP-6)
