Trinitron Color Tv

Transcript

2-348-392-11 (1) Trinitron Color TV GB Operating Instructions • Before operating the unit, please read this manual thoroughly and retain it for future reference. KV-SA32 KV-SA28 M36 © 2004 Sony Corporation 01GB01COV-STMOce.p65 1 Black 10/14/04, 6:06 PM Sony KV-SA32M36 Group F12 (GB)_2-348-392-11 (1) WARNING • Dangerously high voltages are present inside the TV. • TV operating voltage: 220 – 240 V AC. • Do not plug in the power cord until you have completed making all other connections; otherwise a minimum leakage current might flow through the antenna and other terminals to ground. • To avoid battery leakage and damage to the remote, remove the batteries from the remote if you are not going to use it for several days. If any liquid leaks from the batteries and touches your skin, immediately wash it away with water. For your own safety, do not touch any part of the TV, the power cord and the antenna cable during lightning storms. For children’s safety, do not leave children alone with the TV. Do not allow children to climb onto it. Do not place any objects on the TV. The apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids, such as vases, shall be placed on the apparatus. Do not operate the TV if any liquid or solid object falls into it. Have it checked immediately by qualified personnel only. Do not block the ventilation openings of the TV. Do not install the TV in a confined space, such as a bookcase or built-in cabinet. Clean the TV with a dry and soft cloth. Do not use benzine, thinner, or any other chemicals to clean the TV. Do not attach anything (e.g., adhesive tape, cellophane tape, glue) on the painted cabinet of the TV. Do not scratch the picture tube. Do not open the cabinet and the rear cover of the TV as high voltages and other hazards are present inside the TV. Refer servicing and disposal of the TV to qualified personnel. Your TV is recommended for home use only. Do not use the TV in any vehicle or where it may be subject to excessive dust, heat, moisture or vibrations. 2 01GB02WAR-STMOce.p65 2 Black 10/14/04, 6:06 PM Sony KV-SA32M36 Group F12 (GB)_2-348-392-11 (1) To prevent fire or shock hazard, do not expose the TV to rain or moisture. Do not plug in too many appliances to the same power socket. Do not damage the power cord. Install the TV on a stable TV stand and floor which can support the TV set weight. Ensure that the TV stand surface is flat and its area is larger than the bottom area of the TV. Pull the power cord out by the plug. Do not pull the power cord itself. Even if your TV is turned off, it is still connected to the AC power source (mains) as long as the power cord is plugged in. Unplug the TV before moving it or if you are not going to use it for several days. 3 01GB02WAR-STMOce.p65 3 Black 10/14/04, 6:06 PM Sony KV-SA32M36 Group F12 (GB)_2-348-392-11 (1) x Securing the TV To prevent the TV from falling, use the supplied screws, clamps and band to secure the TV. 20 mm 3.8 mm screws clamps band Screw the band to the TV stand and to the provided hole at the rear of your TV. or (1) Put a cord or chain through the clamps. (2) Screw one clamp to a wall or pillar and the other clamp to the provided hole at the rear of your TV. or (1) Attach each end of a cord or chain to the provided holders at the rear of your TV. (2) Securely fix the attached cord or chain to a wall or pillar using an attachment which can support the TV set weight. Note • Use only the supplied screws. Use of other screws may damage the TV. 4 01GB02WAR-STMOce.p65 4 Black 10/14/04, 6:06 PM Sony KV-SA32M36 Group F12 (GB)_2-348-392-11 (1) Table of Contents Installation Menu Adjustment Getting Started ..................................... 6 Setting up your TV (“Initial Setup”) .................................... 7 Introducing the menu system .......... 20 Changing the “Picture” setting ........ 23 Changing the “Sound” setting ......... 25 Changing the “Wide Screen” setting .................................................. 27 Changing the Picture-in-Picture (“PIP”) setting .................................... 28 Changing the “Channel Setup” setting ................................................. 29 Changing the “Setup” setting .......... 31 Overview of Controls TV front and rear panels ..................... 9 Using the remote control and basic functions .................................... 10 GB Advanced Operations Selecting the picture and sound modes .................................................. 12 Using the wide screen mode ............ 13 Enjoying the WEGA Theatre Mode with center speaker ........................... 15 Watching Picture-in-Picture (PIP) ... 16 Enjoying stereo or bilingual programs ............................................. 17 Viewing Teletext ................................. 18 Operating optional components ...... 19 Additional Information Connecting optional components ... 33 Troubleshooting ................................. 36 Specifications ...................... Back cover 5 01GB03TOC-STMOce.p65 5 Black 10/14/04, 6:06 PM Sony KV-SA32M36 Group F12 (GB)_2-348-392-11 (1) Installation x Getting Started 1Step 1 Insert the batteries (supplied) into the remote. b Note • Do not use old or different types of batteries together. Step 2 Connect the antenna cable (not supplied) to 8 (antenna input) at the rear of the TV. Tip • You can also connect your TV to other optional components (see page 33). Step 3 b Plug in the power cord, then press ! on the TV to turn it on. Note • The 1 (standby) indicator flashes green for a few seconds when turning on the TV. This does not indicate a malfunction. Step 4 Set up the TV by following the instructions of the “Initial Setup” menu (see page 7). 6 Installation 01GB04INS-STMOce.p65 6 Black 10/14/04, 6:07 PM Sony KV-SA32M36 Group F12 (GB)_2-348-392-11 (1) x Setting up your TV (“Initial Setup”) When you turn on your TV for the first time, the “Initial Setup” menu will appear. You may change the menu language, preset the TV channels automatically, change the order of TV channels that appear on the screen and adjust the picture position using the buttons on the TV front panel. Tip 1 Installation and V/v/B/b buttons on the remote control can also be used for the • The MENU, operations below. Press 2 +/– to select the desired menu language, then press t. The selected menu language appears. 2 Press 2 +/– to select “Yes”, then press t to preset the channels automatically. The screen will indicate automatic presetting in progress. After all available channels have been tuned and stored, the “Program Sorting” menu appears automatically on the screen. A P Program: TV System: VHF Low 01 Auto To skip automatic channel presetting, select “No”, then press t. If the message “No channel found. Please connect cable/antenna” appears, check your TV connections, then press t. 3 The “Program Sorting” menu enables you to change the order in which the channels appear on the screen. a) If you wish to keep the channels in the tuned order, press MENU. b) If you wish to store the channels in a different order: Program Sorting Program: 01 02 03 04 Select channel 1) Press 2 +/– to select the program number with the channel you wish to rearrange, then press t. continue Installation 01GB04INS-STMOce.p65 7 Black 10/14/04, 6:07 PM Sony KV-SA32M36 Group F12 (GB)_2-348-392-11 (1) 7 continued The selected channel will appear on the screen. 2) Press 2+/– to select the new program number position for your selected channel, then press t. Program Sorting Program: 01 01 02 03 04 Select new position 3) Repeat steps b) 1) and 2) if you wish to change the order of the other channels. c) Press MENU to go to the next menu. 4 Press 2 +/– to adjust the bars on the top and bottom of the menu if they are slanted, then press t. “Picture V-Position” menu appears. 5 If the upper and lower bars are not equally positioned to the top and bottom of the screen, press 2 +/– to adjust them, then press t. If no adjustment is necessary, then press t. 6 Press 2 +/– to select “No”, then press t. This menu will not appear again the next time you turn on the TV by pressing !. To allow this menu to appear again, select “Yes”, then press t. Tips • You can immediately go to the end of the ”Initial Setup” menu by pressing MENU. • You can also set up your TV using the menu system (see page 20). • You can also preset the channels automatically by pressing MENU (AUTO PROG) button on the TV front panel for about five seconds. 8 Installation 01GB04INS-STMOce.p65 8 Black 10/14/04, 6:07 PM Sony KV-SA32M36 Group F12 (GB)_2-348-392-11 (1) Overview of Controls x TV front and rear panels qa TV rear panel qg R L 1 Y CB 2 3 CR qf AUTO PROG:Press [MENU] for 5sec L(MONO) 4 R SOUND MODE MENU PROG (AUTO PROG) qd qs TV front panel 9 0 8 76 5 4 3 2 1 Overview of Controls c– 120W MAX 8 AUTO PROG:Press [MENU] for 5sec L(MONO) R SOUND MENU MODE (AUTO PROG) 4 PROG Button/Terminal 1 ! Function Turn off or turn on the TV. 2 2 3 4 5 6 Standby indicator. 6 Wake Up indicator. 11 1 Remote control sensor. – PROG +/– Select program number. – 2 +/– Adjust volume. t Select TV or video input. Menu operations 5 2 +/– 6 t 7 MENU – 33 Select and adjust items. – Confirm selected items. – Display or cancel the menu. – Preset channels automatically. 8 Select sound mode options. 5-Band Graphic Equalizer display will appear. 12 t4 Video input terminal 4. 33 i Headphone jack. 7 (AUTO PROG) 8 SOUND MODE 9 0 qa qs qd qf qg Page 6 – Component video input terminal. 34 T Monitor output terminal. 33 t1, t2, t3 Video input terminal 1, 2, 3. 33 8 Antenna input terminal. 33 Center speaker input terminal. 35 Overview of Controls 01GB04INS-STMOce.p65 9 Black 10/14/04, 6:07 PM Sony KV-SA32M36 Group F12 (GB)_2-348-392-11 (1) 9 x Using the remote control and basic functions qk VIDEO ql w; DVD CENTER WEGA SP THEATRE wa ws wd wf A/B MENU 1 2 3 4 5 6 7 8 wg 9 wh wj wk q; qa qs wl 1 2 3 4 5 6 7 8 9 0 Description Turn off temporarily or turn on the TV. 3a 4t 5 WEGA THEATRE 6 CENTER SP qa qd Display the TV program. – Select video input. 33 qf qg 15 Select TV’s center speaker mode. 15 Change the picture size. 14 Select surround mode options: “TruSurround” (surround sound that spreads out to the rear of a room), “WOW” (full, deep bass sound), “Simulated” (stereo-like monaural sound), “Off”. – qf Jump to last program number that has been watched for at least five seconds. – qg PROG +/– qk ql w; DVD wj Select program number. – Mute the sound. – Display on-screen information. – Select component video input. 34 Select sound mode options. 5-Band Graphic Equalizer display will appear. 12 wk Select picture mode options. 12 wl 0 – 9, e; 2 +/– es RESET Input numbers. – OPTION RESET ea es qh qj TV Page – Select WEGA Thearte Mode. qd PROG e; Button 1 ?/1 Adjust volume. – Set TV to factory setting. 36 Menu operations 8 MENU wg V, v, B, b wh Display or cancel the menu. 22 Select and adjust items. 22 Confirm selected items. 22 Stereo/bilingual operations 7 A/B Select stereo/bilingual mode. Timer operations qh Set TV to turn off automatically (Sleep Timer) according to the desired period of time (max. of one hour and 30 min.). 10 17 – Overview of Controls 01GB04INS-STMOce.p65 10 Black 10/14/04, 6:07 PM Sony KV-SA32M36 Group F12 (GB)_2-348-392-11 (1) Button qj (Wake Up Timer) Page – Teletext operations (green label) 4 7 q; qs z (red, green, Stop Teletext from scrolling. 18 Enlarge the Teletext display. 18 Display Teletext broadcast. 18 Access a FASTEXT menu. 18 Display the next or previous page. 18 yellow, blue) qg qh qj ql , Show TV screen while waiting for Teletext page. 18 Display Teletext service contents. 18 Reveal concealed information. 18 PIP operation (yellow label) 9 PIP PROG +/ Display and change programs in the sub screen. PIP PROG – wa Adjust position of sub screen. ws wd wf wh qk wg wg wg wg wh e; ea > . x X N 2 +/– OPTION 16 16 Swap main and sub screens. 16 Swap sound between main and sub screen. Display a sub screen. Change sub screen to main screen. 16 16 16 Optional components operations 2 VIDEO ?/1 Power. Overview of Controls Description Set TV to turn on automatically according to the desired period of time (max. of 12 hours). The indicator on TV lights up amber once you set the wake up timer. If no buttons or controls are pressed for more than one hour after the TV is turned on using the wake up timer, the TV automatically goes into standby mode. 19 Mute the sound. 19 Fast forward/Step forward. Rewind/Step backward. Stop. Pause. Play. Adjust volume. Operate optional components. 19 19 19 19 19 19 19 WOW, TruSurround, SRS and symbol are trademarks of SRS Labs, Inc. WOW and TruSurround technologies are incorporated under license from SRS Labs, Inc. Licensed by BBE Sound, Inc. under USP4638258, 4482866. “BBE” and BBE symbol are trademarks of BBE Sound, Inc. Overview of Controls 01GB04INS-STMOce.p65 11 Black 10/14/04, 6:07 PM Sony KV-SA32M36 Group F12 (GB)_2-348-392-11 (1) 11 Advanced Operations x Selecting the picture and sound modes You can select picture and sound modes and adjust the setting to your preference in the “Personal” option. Selecting the picture mode VIDEO Press DVD CENTER WEGA SP THEATRE A/B to select the desired picture mode. Select To view “Dynamic” high contrast pictures. “Standard” normal pictures. “Soft” mild pictures. “Personal” the last adjusted picture setting from the “Picture Adjustment” option in the menu (see page 24). MENU 1 2 4 5 6 7 8 9 3 0 Selecting the sound mode Press (or SOUND MODE on the front panel) to select the desired sound mode. 5-Band Graphic Equalizer display will appear. Select To listen to “Dynamic” Dynamic dynamic and clear sound that emphasizes both the low and high tones. 100 300 1k 3k 8k “Drama” Drama sound that emphasizes voice and high tones. 100 300 1k 3k 8k “Soft” soft, natural and relaxing sounds. Soft 100 300 1k 3k 8k “Personal” Personal the last adjusted sound setting from the “Sound Adjustment” option in the menu (see page 26). 100 300 1k 3k 8k 12 Advanced Operations 01GB05AVD-STMOce.p65 12 Black 10/14/04, 6:07 PM Sony KV-SA32M36 Group F12 (GB)_2-348-392-11 (1) x Using the wide screen mode The wide screen mode feature allows you to watch the picture filling the 16:9 screen of the TV. Watching the picture in wide screen mode automatically – Auto Wide The TV automatically selects optimum wide screen mode according to the signal input and displays the picture to fill the 16:9 screen. The examples in the table below show the settings preset at the factory; “Auto Wide” is set to “On” and “4:3 Default” is set to “Wide Zoom” in the “Wide Screen” menu (see page 27). When receiving … Auto Wide functions to select … normal 4:3 aspect ratio picture with or without an ID-1 or WSS signal. The picture changes to Wide Zoom* letter box picture with an ID-1 or WSS signal. Zoom Black bands may appear on the top and bottom of the screen. squeezed picture with an ID-1 or WSS signal. Full * When a normal 4:3 picture is received, “Wide Zoom” mode is automatically selected with the factory setting. You can display picture as it is without enlarging it (“Normal” mode) if you set “4:3 Default” in the “Wide Screen” menu to “Normal” (see page 27). Note • The Auto Wide feature may not work correctly depending on the quality of signal. In this case, select the wide screen mode manually using the button (see page 14). continue Advanced Operations 01GB05AVD-STMOce.p65 13 Black 10/14/04, 6:07 PM Sony KV-SA32M36 Group F12 (GB)_2-348-392-11 (1) 13 continued Watching the picture in wide screen mode manually Press repeatedly until the mode indication you want is displayed on the screen. 1 2 3 4 5 6 8 9 7 Wide Zoom Normal Zoom Full 0 PROG OPTION RESET TV Notes • You can also select the wide screen mode manually using the menu (see page 27). button on the remote or using the • When the wide screen mode is selected by pressing the menu, the Auto Wide feature does not work temporarily. The Auto Wide feature functions again when: – you change a TV channel. – you change the video input. – the TV is turned off and on again. – the signal format is changed. 14 Advanced Operations 01GB05AVD-STMOce.p65 14 Black 10/14/04, 6:07 PM Sony KV-SA32M36 Group F12 (GB)_2-348-392-11 (1) x Enjoying the WEGA Theatre Mode with center speaker The WEGA Theatre Mode enables you to enjoy the best picture, sound and surround effect of a cinema from a DVD source. You can use your TV speaker as the center speaker of your audio system for optimum vocal enhancement and control its sound volume from the remote of the TV. Setting up WEGA Theatre Mode 1. Connect the center speaker terminals of the amplifier to the center speaker input terminal on the TV (see page 35). 2. Select the proper video input from “WEGA Theatre Setup” menu and turn on the connected equipment (see page 31). 3. Set up the remote to work with the connected equipment (see page 19). VIDEO DVD CENTER WEGA SP THEATRE CENTER SP To Press switch to WEGA Theatre Mode WEGA THEATRE. Be sure to aim the remote control at the TV set and connected equipment for about one second after the button is pressed. The connected equipment turns on automatically from standby mode and will start playing. A/B WEGA THEATRE MENU 1 2 4 5 6 7 8 9 The “Picture Mode” and “Sound Mode” will switch automatically to “Personal” and you can adjust the setting to your personal preference (see pages 24 and 26). 3 0 PROG switch to center speaker mode CENTER SP repeatedly until “CENTER IN Speaker” appears. To return to normal speaker mode, press the button repeatedly until “MAIN Speaker” appears. adjust center speaker volume 2 +/– 2 +/– OPTION RESET TV Notes • Be sure to place your TV and connected equipment adjacent to each other so that you can control both the TV and the connected equipment by using the TV’s remote control at the same time (see page 19). • The WEGA Theatre and center speaker modes are automatically cancelled when you change the program number, video input or turn the TV off and on again. • When the TV is in the center speaker mode, you cannot use the PIP feature, change the surround sound and the “Intelligent Volume” mode. • Some equipment might not respond properly when WEGA THEATRE button is pressed. In this case, use the equipment’s own remote control. Advanced Operations 01GB05AVD-STMOce.p65 15 Black 10/14/04, 6:07 PM Sony KV-SA32M36 Group F12 (GB)_2-348-392-11 (1) 15 x Watching Picture-in-Picture (PIP) With the PIP feature, you can display two different TV programs or video input at the same time by using the button. VIDEO DVD To Press Display a sub screen . To cancel the sub screen, press the button again. Change a program number in the sub screen PIP PROG + or PIP PROG –. CENTER WEGA SP THEATRE A/B MENU PIP PROG +/ PIP PROG – 1 2 3 4 5 6 7 8 9 0 Adjust position of sub screen . Swap pictures between the main and sub screens . Swap sound between the main and sub screens . A “ ” symbol will appear next to the program number or video input display to indicate which screen you are hearing. Selecting TV program using PIP You can select your desired TV program directly from the PIP sub screen by using PIP PROG +/– buttons. 1. Press PIP PROG +/– until the desired program appears in the sub screen. 2. Press to change the sub screen program to the main screen. Notes • The PIP feature is not available when the TV is in the center speaker mode (page 15) and you cannot set the TV to the center speaker mode while viewing the PIP. • You can only enjoy stereo sound from the main screen. • You cannot change the picture to a video input in the sub screen. You can only display a video input, in the sub screen by swapping the pictures when a video input is displayed in the main screen. • The picture and sound from the T (monitor output) terminals will always be from the main (see page 33). screen, even when you select the sub screen sound by pressing 16 Advanced Operations 01GB05AVD-STMOce.p65 16 Black 10/14/04, 6:07 PM Sony KV-SA32M36 Group F12 (GB)_2-348-392-11 (1) x Enjoying stereo or bilingual programs You can enjoy stereo sound or bilingual programs of NICAM and A2 stereo systems by using the A/B button. When receiving a NICAM program A/B A/B Broadcasting On-screen display (Selected sound) NICAM stereo NICAM (Stereo sound) NICAM bilingual NICAM Main t NICAM Sub t Mono (Main sound) (Sub sound) (Regular sound) NICAM monaural NICAM Main (Main sound) MENU 1 2 4 5 6 7 8 9 3 0 PROG Mono (Regular sound) t Mono (Regular sound) When receiving an A2 program Broadcasting On-screen display (Selected sound) A2 stereo Stereo (Stereo sound) A2 bilingual Main (Main sound) t Mono (Regular sound) t Sub (Sub sound) t OPTION RESET t t CENTER WEGA SP THEATRE t DVD t VIDEO t TV Note • If the stereo sound is noisy when receiving a stereo program, select “Mono”. The sound becomes monaural but the noise is reduced. Advanced Operations 01GB05AVD-STMOce.p65 17 Black 10/14/04, 6:07 PM Sony KV-SA32M36 Group F12 (GB)_2-348-392-11 (1) 17 x Viewing Teletext Some TV stations broadcast an information service called Teletext which allows you to receive various information, such as stock market reports and news. You can use the buttons on the remote to view Teletext. VIDEO DVD CENTER WEGA SP THEATRE A/B To Do this display a Teletext page on the TV picture Press . Each time you press , the screen changes as follows: Teletext t Teletext and TV t TV. If there is no Teletext broadcast, “100” is displayed at the top left corner of the screen. check the contents of a Teletext service Press . An overview of the Teletext contents, including page numbers, appears on the screen. select a Teletext page Press the number buttons to enter the three-digit page number of the desired Teletext page. If you make a mistake, reenter the correct page number. To access the next or previous page, press or . hold (pause) a Teletext display Press to display the symbol “ ” at the top left corner of the screen. To resume normal Teletext viewing, press . reveal concealed information (e.g., an answer to a quiz) Press . To conceal the information, press the button again. enlarge the Teletext display Press . Each time you press , the Teletext display changes as follows: Enlarge upper half t Enlarge lower half t Normal size. MENU z (red, green, yellow, blue) 1 2 3 4 5 6 8 9 7 , 0 PROG OPTION RESET TV stand by for a Teletext (1) Enter the Teletext page number that page while watching you want to refer to, then press . a TV program (2) When the page number is displayed, press to show the text. select a FASTEXT menu or the colored boxes Press z (red, green, yellow and blue) that corresponds to the desired menu or page number. turn off Teletext Press a. Note • The FASTEXT feature can be used only when the FASTEXT broadcast is available. 18 Menu Adjustment Advanced Operations 01GB05AVD-STMOce.p65 18 Black 10/14/04, 6:07 PM Sony KV-SA32M36 Group F12 (GB)_2-348-392-11 (1) x Operating optional components You can use the supplied remote to operate Sony audio/video equipment. Setting up the remote to work with other connected equipment While keeping VIDEO ?/1 pressed, press the corresponding number button for the desired equipment (see the chart below). For example, to operate a Sony 8 mm VCR: To control Hold down VIDEO ?/1 and press Audio System 1, 1x, 2 or 3 0, 1, 2, or 3 DVD 1, 2 or 3 4, 5 or 6 VTR1 (Beta), VTR2 (8 mm) or VTR3 (VHS) 7, 8 or 9 VIDEO + 8 Operating audio/video equipment Press VIDEO ?/1 or while keeping OPTION pressed, press N , x , ., > , X, or 2 +/– (see the chart below). To Press turn on/off VIDEO ?/1 play N while keeping OPTION pressed. stop x while keeping OPTION pressed. fast forward/ step forward or rewind/ step backward > or . while keeping OPTION pressed. pause X while keeping OPTION pressed. Press again to resume normal playback. mute the sound (Audio System 1, 1x, 2 or 3 only) while keeping OPTION pressed. adjust volume (Audio System 1, 1x, 2 or 3 only) 2 +/– while keeping OPTION pressed. Notes • If the equipment does not have a certain function, the corresponding button on the remote will not operate. • Some equipment might not respond properly to buttons on TV’s remote. In this case, use the equipment’s own remote control. Advanced Operations 01GB05AVD-STMOce.p65 19 Black 10/14/04, 6:07 PM Sony KV-SA32M36 Group F12 (GB)_2-348-392-11 (1) 19 Menu Adjustment x Introducing the menu system The MENU button lets you open a menu and change the settings of your TV. The following is an overview of the menu system. Picture icon Sound icon Wide Screen icon PIP icon Channel Setup icon Return icon Name of the current menu Setup Language: Picture Position WEGA Theatre Setup Video Label Color System: Menu level 3 Menu level 2 Setup icon Select Confirm End Menu level 1 User Guidance Level 1 Level 2 Level 3/Function “Picture” “Mode” Select the picture mode: “Dynamic” t “Standard” t “Soft” t “Personal” Page 23 “Picture Adjustment” Adjust the “Personal” option: “Picture” t “Brightness” t “Color” t “Hue” t “Sharpness” t “Reset” “Color Temperature” Adjust white color tint: “Cool” t “Neutral” t “Warm” “Sound” “3D Intelligent Picture” Optimize picture quality: “On” t “Off” “Mode” Select the sound mode: “Dynamic” t “Drama” t “Soft” t “Personal” 25 “Sound Adjustment” Adjust sound frequency settings of “Personal” option: “Adjust” t “Reset” Select to emphasize the left and right speakers. “Balance” “Intelligent Volume” Adjust volume automatically: “On” t “Off” “Surround” 20 Select the surround mode: “TruSurround” t “WOW” t “Simulated” t “Off” Menu Adjustment 01GB05AVD-STMOce.p65 20 Black 10/14/04, 6:07 PM Sony KV-SA32M36 Group F12 (GB)_2-348-392-11 (1) Level 1 Level 3/Function Level 2 Select the wide screen mode: “Wide Zoom” t “Normal”t “Full”t “Zoom” “Wide Screen” “Wide Mode” “PIP” “Auto Wide” Select an optimum wide screen mode automatically: “On” t “Off” “4:3 Default” Change the picture to “Wide Zoom”or “Normal” when the normal 4:3 picture with or without ID-1 or WSS signal is received. “V Center” Adjust the vertical position of the picture in “Wide Zoom” or “Zoom” mode. “V Size” Adjust the vertical size of the picture in “Wide Zoom” or “Zoom” mode. “PIP” Display a sub screen within the main picture: “On” t “Off” “Swap” Exchange pictures between main screen and sub screen. “Position” Change the position of the sub screen “Channel Setup” “Auto Program” “Setup” Page 27 28 Preset channels automatically. 29 “Manual Program” Preset channels manually. “Program Label” Label the program number. “Program Block” Block unwanted programs. “Program Sorting” Change the order in which the channels appear on the screen. “Language” Change the menu language: “English” t “ ” (Chinese) “Picture Position” Adjust the picture position. “WEGA Theatre Setup” Select the WEGA Theatre Mode. 31 “Direct Input” Select the input for connected equipment. “Speaker” Select the speaker mode: “MAIN” t “CENTER IN” “Video Label” Label the connected equipment. “Color System” Select the color system: “Auto” t “PAL” t “SECAM” t “NTSC3.58” t “NTSC4.43” continue Menu Adjustment 01GB05AVD-STMOce.p65 21 Black 10/14/04, 6:07 PM Sony KV-SA32M36 Group F12 (GB)_2-348-392-11 (1) 21 continued How to use the menu MENU Picture Mode: Dynamic Picture Adjustment Color Temperature: Cool 3D Intelligent Picture: On Press MENU to display the menu. Select 1 2 3 4 5 6 7 8 9 Press V or v to select the desired item. Confirm Channel Setup Auto Program Manual Program Program Label Program Block Program Sorting 0 PROG Select (or b) to Press confirm your selection and go to the next level. OPTION RESET TV End Confirm End Channel Setup Auto Program Manual Program Program Label Program Block Program Sorting Select Confirm End Other menu operations To Press Adjust the setting value V, v, B or b. Move to the next/previous menu level B or b. Cancel the menu MENU. Tips • If you want to exit from Menu level 2 to Menu level 1, press V or v until the return icon ( ) is . highlighted, then press • The MENU, t and 2 +/– buttons on the TV front panel can also be used for the operations above (see page 9). Note • When a feature is dimmed in the menu, it is not selectable. 22 Menu Adjustment 01GB05AVD-STMOce.p65 22 Black 10/14/04, 6:07 PM Sony KV-SA32M36 Group F12 (GB)_2-348-392-11 (1) x Changing the “Picture” setting The “Picture” menu allows you to adjust the picture settings. 1 2 Press MENU. Make sure the “Picture” icon ( selected, then press . ) is Picture Mode: Dynamic Picture Adjustment Color Temperature: Cool 3D Intelligent Picture: On Select 3 End Confirm Press V or v to select the desired item (e.g., “Mode”), then press . Select To “Mode” choose either “Dynamic”, “Standard”, “Soft” or “Personal”* (see page 12). “Color Temperature” adjust white color tint. Choose either “Cool” (blue tint), “Neutral” (neutral tint) or “Warm” (red tint). “3D Intelligent Picture” optimize picture quality. Automatically, the picture will become clearer and sharper if the signal is good and noise will be reduced if the signal is noisy. Press V or v to select “On”, then press . To cancel, select “Off”, then press . * You can adjust the setting to your personal preference in the “Picture Adjustment” and “Color Temperature” options only when the “Personal” mode is selected (see page 24). Note • For NTSC 3.58 color system, “3D Comb Filter : On” or “3D–NR : On” display will appear when “3D Intelligent Picture” changes from one mode to the other . For PAL color system, Digital Comb Filter and 3D-NR are also available. continue Menu Adjustment 01GB05AVD-STMOce.p65 23 Black 10/14/04, 6:07 PM Sony KV-SA32M36 Group F12 (GB)_2-348-392-11 (1) 23 continued Adjusting the “Picture Adjustment” items under “Personal” mode 1 Press V or v to select either “Picture” (contrast), “Brightness”, “Color”, “Hue” (color tones) or “Sharpness”, then press . Selecting “Reset” will set your TV to the factory setting. 2 3 Press V,v,B or b to adjust the setting of your selected item, then press . Repeat the above steps to adjust other items. The adjusted settings will be received when you select “Personal”. Notes • “Hue” can be adjusted for the NTSC color system only. • Reducing “Sharpness” can also reduce picture noise. 24 Menu Adjustment 01GB05AVD-STMOce.p65 24 Black 10/14/04, 6:07 PM Sony KV-SA32M36 Group F12 (GB)_2-348-392-11 (1) x Changing the “Sound” setting The “Sound” menu allows you to adjust the sound settings. 1 2 Press MENU. Press V or v to select the “Sound” icon ( ), then press . Sound Mode: Dynamic Sound Adjustment Balance Intelligent Volume: Off Off Surround: Select 3 End Confirm Press V or v to select the desired item (e.g., “Mode”), then press . Select To “Mode” choose either “Dynamic”, “Drama”, “Soft” or “Personal”* (see page 12). “Balance” Press v or B to emphasize the left speaker. Press V or b to emphasize the right speaker. “Intelligent Volume” adjust the volume of all program numbers and video inputs automatically. Press V or v to select “On”, then press . To cancel, select “Off”, then press “Surround” . choose either “TruSurround”, “WOW”**, “Simulated” or “Off” (see page 10). * You can adjust the setting to your personal preference in the “Sound Adjustment” option only when the “Personal” mode is selected (see page 26). ** BBE High Definition sound is fully activated maximizing the sound effect in the WOW mode. Note • “Intelligent Volume” is not selectable when “TruSurround” is selected. continue Menu Adjustment 01GB06ADJ-STMOce.p65 25 Black 10/14/04, 6:07 PM Sony KV-SA32M36 Group F12 (GB)_2-348-392-11 (1) 25 continued Adjusting the “Sound Adjustment” item under “Personal” mode The 5-Band Graphic Equalizer feature allows you to adjust sound frequency settings of “Personal” mode in the menu. 1 Make sure that “Adjust” is selected, then press . Adjustment: Personal Adjust Reset Selecting “Reset” will set your TV to the factory setting. 100 300 Select 2 Confirm 1k 3k 8k End Press B or b to select the desired sound frequency, then press V or v to adjust the setting and press . The adjusted settings will be received when you select “Personal”. Notes • Adjusting higher frequency will affect higher pitched sound and adjusting lower frequency will affect lower pitched sound. • You may display the settings directly using the SOUND MODE button on the TV front panel (see page 9) or button on the remote control (see page 10). 26 Menu Adjustment 01GB06ADJ-STMOce.p65 26 Black 10/14/04, 6:07 PM Sony KV-SA32M36 Group F12 (GB)_2-348-392-11 (1) x Changing the “Wide Screen” setting The “Wide Screen” menu allows you to watch the picture filling the 16:9 screen of the TV. 1 2 Press MENU. Press V or v to select the “Wide Screen” icon ( ), then press . Wide Screen Wide Mode: Auto Wide: 4:3 Default: V Center: V Size: Select 3 Wide Zoom On Wide Zoom 00 00 Confirm End Press V or v to select the desired item (e.g., “Wide Mode”), then press . Select To “Wide Mode” select the desired wide screen mode to fit the 16:9 screen. Press V or v to select “Wide Zoom”, “Normal”, “Full” or “Zoom”, then press . “Auto Wide” automatically display the picture in optimum wide screen mode. Press V or v to select the “On” then press . Select “Off” if you want to display any picture in currently selected wide screen mode. “4:3 Default” display a 4:3 picture in “Wide Zoom” or “Normal” mode. Press V or v to select the “Wide Zoom” or “Normal”, then press . “V Center” adjust the vertical position of the picture in “Wide Zoom” or “Zoom” mode. Press V or v to move the picture, then press . “V Size” adjust the vertical size of the picture in “Wide Zoom” or “Zoom” mode. Press V or v to adjust the vertical size, then press . Tip • You can also change to wide-mode picture size by pressing the control (see page 14) button on the remote Note • “4:3 Default” does not function when “Auto Wide” is set to “Off”. Menu Adjustment 01GB06ADJ-STMOce.p65 27 Black 10/14/04, 6:07 PM Sony KV-SA32M36 Group F12 (GB)_2-348-392-11 (1) 27 x Changing the Picture-in-Picture (“PIP”) setting The “PIP” menu allows you to display a sub screen, exchange pictures between the main and sub screens and change the sub screen position. 1 2 Press MENU. Press V or v to select the “PIP” icon ( then press . PIP PIP: Swap Position: ), Select 3 To “PIP” display a sub screen. Press V or v to select “On”, then press To cancel, press 28 . or select “Off”, then press End Confirm Press V or v to select the desired item (e.g., “PIP”), then press Select Off . . “Swap” exchange pictures between the main screen and sub screen. “Position” change the position of the sub screen. Press V or v to select the desired position, then press . Menu Adjustment 01GB06ADJ-STMOce.p65 28 Black 10/14/04, 6:07 PM Sony KV-SA32M36 Group F12 (GB)_2-348-392-11 (1) x Changing the “Channel Setup” setting The “Channel Setup” menu allows you to preset channels automatically, manually preset channels, label the program number, block unwanted programs and change the order of TV channels that appear on the screen. 1 2 Press MENU. Press V or v to select the “Channel Setup” icon ( ), then press . Channel Setup Auto Program Manual Program Program Label Program Block Program Sorting Select 3 End Confirm Press V or v to select the desired item (e.g., “Auto Program”), then press Select . To “Auto Program” preset channels automatically. “Manual Program” manually preset desired channels and channels that cannot be preset automatically (see Presetting channels manually on page 30). “Program Label” label the program number. (1) Select “Program” and press . Press V or v to select the program number, then press (2) Select “Label” and press . Press V or v to select alphanumeric characters for the label, then press . . “Program Block” block unwanted programs. (1) Select “Program” and press . Press V or v to select the program number, then press . (2) Select “Block” and press , then press V or v to choose either “On” or “Off”. If you preset a blocked program number, that program number will be unblocked automatically. “Program Sorting” change the order in which the channels appear on the screen. (see step 3 b) of the section “Intial Setup” in page 7). Notes • You may label the program numbers so that you can see the program labels in the “Program Sorting” menu. • If you sort a blocked program, that program will remain blocked. continue Menu Adjustment 01GB06ADJ-STMOce.p65 29 Black 10/14/04, 6:07 PM Sony KV-SA32M36 Group F12 (GB)_2-348-392-11 (1) 29 continued Presetting channels manually 1 After selecting “Manual Program”, select the program number to which you want to preset a channel. . (1) Make sure “Program” is selected, then press (2) Press V or v until the program number you want to preset appears on the menu, then press . 2 Manual Program Program: TV System: VHF Low Fine: Skip: Signal Booster: Select 01 B/G Auto Off Auto Confirm End Select the desired channel. (1) Make sure either “VHF Low”, “VHF High” or “UHF” is selected, then press . (2) Press V or v until the desired channel’s broadcast appears on the TV screen, then press . 3 If the sound of the desired channel is abnormal, select the appropriate TV system. (1) Press V or v to select “TV System”, then press . (2) Press V or v until the sound becomes normal, then press 4 . If you are not satisfied with the picture and sound quality, you may be able to improve them by using the “Fine” tuning feature. (1) Press V or v to select “Fine”, then press . (2) Press V or v to select “Manual”, then press . (3) Press V,v,B or b until the picture and sound quality are optimal, then press . The + or – icon on the menu flashes while tuning. 5 If you want to skip this program number when using PROG +/–, you can select the “Skip” feature. (1) Press V or v to select “Skip”, then press (2) Press V or v to select “On”, then press To cancel, select “Off”, then press 6 . . . If the TV signal is too strong (picture distorted; picture with lines; signal interference) or weak (snowy picture), you may be able to improve the picture quality by setting the “Signal Booster” feature. (1) Press V or v to select “Signal Booster”, then press . (2) Press V or v to select either “Off”(for picture distorted; picture with lines; signal interference) or “Auto” (for snowy picture), then press . 30 Menu Adjustment 01GB06ADJ-STMOce.p65 30 Black 10/14/04, 6:07 PM Sony KV-SA32M36 Group F12 (GB)_2-348-392-11 (1) x Changing the “Setup” setting The “Setup” menu allows you to change the menu language, adjust the picture position, setup WEGA Theatre Mode, label the connected equipment and select the color system. 1 2 Press MENU. Press V or v to select the “Setup” icon ( then press ), Setup Language: English Picture Position WEGA Theatre Setup Video Label Color System: Auto . Select 3 End Confirm Press V or v to select the desired item (e.g., “Language”), then press Select To “Language” change the menu language. Press V or v to select either “English” or “ press . “Picture Position” . ” (Chinese), then adjust the picture position when it is not aligned with the TV screen. Press V or v to select “Picture Rotation” or “Picture V-Position”, then press . Press V, v, B or b to adjust picture position, then press . “WEGA Theatre Setup” enjoy best picture, sound and surround effect of a cinema. Press V or v to select “Direct Input”, then press . Select either “Video 1”, “Video 2”, “Video 3”, “Video 4” or “DVD” for the connected equipment that you want to view with WEGA theatre, then press . . Normally select “MAIN”. Select “Speaker” and press When you want to use the TV’s speakers as the center speaker, press V or v to select “CENTER IN”, then press . continue Menu Adjustment 01GB06ADJ-STMOce.p65 31 Black 10/14/04, 6:07 PM Sony KV-SA32M36 Group F12 (GB)_2-348-392-11 (1) 31 continued Select To “Video Label” label the connected equipment. (1) Select “Video Input” and press . Press V or v to select the input you want to label, then press . (2) Select “Label” and press , then press V or v to select the label options: ”Video 1/Video 2/Video 3/Video 4/ DVD”, “VCR”, “SAT”, “Game” or “Edit”*. * You may edit the video label. Press V or v to select . alphanumeric characters for the label, then press “Color System” 32 select the color system. Press V or v to select “Auto”, “PAL”, “SECAM”, “NTSC3.58” or . Normally, set this to “Auto”. “NTSC4.43”, then press Menu Adjustment 01GB06ADJ-STMOce.p65 32 Black 10/14/04, 6:07 PM Sony KV-SA32M36 Group F12 (GB)_2-348-392-11 (1) Additional Information x Connecting optional components Connecting to the video input terminal ( t ) S Video cable (not supplied) TV front panel Camcorder L(MONO) Audio/Video cable (not supplied) R 4 Video game equipment TV rear panel R L 1 c– 120W MAX 8 Y CB 2 3 CR Antenna cable (not supplied) Audio/Video cable (not supplied) S Video cable (not supplied) VCR Notes • If you connect a VCR to 8 (antenna input), preset the signal output from the VCR to the program number 0 on the TV (see page 30). • When both (S video) and (video) for t1 or t4 are connected at the same time, (S video) is automatically selected. To view (video), disconnect the S video cable. Connecting to the monitor output terminal ( T ) TV rear panel R c– 120W MAX 8 L 1 Y CB 2 3 CR Audio/Video cable (not supplied) Audio system VCR continue Additional Information 01GB07ADJ-STMOce.p65 33 Black 10/14/04, 6:08 PM Sony KV-SA32M36 Group F12 (GB)_2-348-392-11 (1) 33 continued Connecting to the component video input terminal ( ) TV rear panel R L 1 c– 120W MAX 8 Y CB 2 3 CR Component video cable (not supplied) DVD player Audio cable (not supplied) Notes • If your DVD player can output interlace and progressive mode signals, select the interlace (component video input) on your TV. Your TV can receive output when connecting to either 525i/60Hz or 625i/50Hz interlace signals. • Some DVD player terminals may be labeled differently: Connect To (on the DVD player) Y (green) Y CB (blue) CB, PB, Cb or B-Y CR (red) CR, PR, Cr or R-Y • If you select “DVD” on your TV screen, the signal from the T (monitor output) jacks will not be output properly. This does not indicate a malfunction. 34 Additional Information 01GB07ADJ-STMOce.p65 34 Black 10/14/04, 6:08 PM Sony KV-SA32M36 Group F12 (GB)_2-348-392-11 (1) Connecting an amplifier to the center speaker input terminal ( ) If you use an amplifier with a Dolby* surround decoder instead of the TV’s audio system, you can use the TV’s speakers as the center speaker for your audio system. Using the speaker cords supplied with the amplifier, connect the center speaker terminals of the amplifier to the (center speaker input) terminals on the TV. Component video cable (not supplied) TV rear panel R c 120W MAX 8 L 1 Y CB 2 3 DVD player CR Audio cable (not supplied) Optical digital cable (not supplied) C– 120W MAX 8 Amplifier Front speaker (L) Front speaker (R) Rear speaker (L) Rear speaker (R) Woofer Notes • To use the TV’s speakers as the center speaker, you can press the CENTER SP button on the remote control (see page 10) or display the “WEGA Theatre Setup” from “Setup” menu and select “CENTER IN” for “Speaker” (see page 31). • If your TV is set to “CENTER IN Speaker” and nothing is connected to the center speaker input terminals on the rear of TV, or the sound source emitted from the amplifier does not contain the center speaker channel, no sound will be heard from the TV’s speaker. * “Dolby” is a trademark of Dolby Laboratories. Additional Information 01GB08ADV-STMOce.p65 35 Black 10/14/04, 6:08 PM Sony KV-SA32M36 Group F12 (GB)_2-348-392-11 (1) 35 x Troubleshooting If you find any problem while viewing your TV, you can either use the Reset function or check the Troubleshooting guide below. If the problem persists, contact your Sony dealer. 7 9 8 Reset function 0 PROG Press the RESET button on your remote control. Your TV will go blank for a few seconds then the “Initial Setup” menu will appear. OPTION RESET RESET Pressing RESET will set your TV to the factory setting, but certain problems may be solved. TV Troubleshooting guide Symptom Snowy picture Noisy sound Solutions Possible cause • The connection is loose • Check the antenna cable and connection or the cable is on the TV, VCR and at the wall. damaged. Page 33 • The antenna setup is inappropriate. • Check the antenna setup. Contact a Sony dealer for advice. – • Channel presetting is inappropriate or incomplete. • Display the “Channel Setup” menu and select “Manual Program” to preset the channel again. 30 • Signal transmission is low. • Display the “Channel Setup” menu and set the “Signal Booster” to “Auto” from “Manual Program”. • Try using an external booster. 30 • Turn off or disconnect the external booster if it is in use. • Display the “Channel Setup” menu and set the “Signal Booster” to “Off” from “Manual Program”. – Distorted picture • Broadcast signals are too strong. – 30 Noisy sound Good picture Noisy sound 36 • The TV system setting • Display the “Channel Setup” menu and is inappropriate. select the appropriate “TV System” from “Manual Program”. 30 • PIP sound is selected • Press when PIP is displayed. 16 or . Additional Information 01GB08ADV-STMOce.p65 36 Black 10/14/04, 6:08 PM Sony KV-SA32M36 Group F12 (GB)_2-348-392-11 (1) Symptom No picture Possible cause Solutions Page • The power cord, antenna or VCR is not connected. • Check the power cord, antenna and VCR connections. 33 • The TV is not turned on. • Press ?/1 (power). 10 • Press ! (main power) on the TV to turn off the TV for about five seconds, then turn it on again. 9 • The volume level is too • Press 2 + to increase the volume level. low. 10 • The sound is muted. to cancel the muting. 10 or 16 No sound Good picture • Press • PIP sound is selected • Press when PIP is displayed. . No sound Dotted lines or stripes Double images or • Broadcast signals are reflected by nearby “ghosts” mountains or buildings. • The antenna setup is inappropriate. No color – • Do not use a hair dryer or other • There is local equipment near the TV. interference from cars, neon signs, hair dryers, • Check the antenna setup. Contact a Sony power generators, etc. dealer for advice. – • Use a highly directional antenna. – • Use the fine tuning (“Fine”) function. 30 • Check the antenna setup. Contact a Sony dealer for advice. – • Use of an external • Turn off or disconnect the external booster booster is inappropriate. if it is in use. – • The color level setting is too low. • Display the “Picture” menu and select “Personal” of “Mode”, then adjust the “Color” level in “Picture Adjustment”. 24 • The color system setting is inappropriate. • Display the “Setup” menu and check the “Color System” setting (usually set this to “Auto”). 32 • The antenna setup is inappropriate. • Check the antenna setup. Contact a Sony dealer for advice. – continue Additional Information 01GB08ADV-STMOce.p65 37 Black 10/14/04, 6:08 PM Sony KV-SA32M36 Group F12 (GB)_2-348-392-11 (1) 37 continued Symptom Picture slant Good mo rning! Abnormal color patches Possible cause Solutions Page • Keep external speakers or other electrical equipment away from the TV. – • Display the “Picture Position” under “Setup” menu, then adjust “Picture Rotation” and “Picture V-Position” so that the picture is aligned to the TV screen. 31 • Keep external speakers or other • The magnetic equipment away from the TV. Do not disturbance from move the TV while the TV is turned on. external speakers or Press ! (main power) on the TV to turn other equipment, or the off the TV for about 15 minutes, then turn direction of the earth’s it on again to demagnetize the TV. magnetic field may affect the TV. – • The magnetic disturbance from external speakers or other equipment, or the direction of the earth’s magnetic field may affect the TV. TV cannot receive • The connection is loose or the cable is stereo broadcast damaged. sound. or Stereo broadcast sound switches on and off or is distorted. “100” appears at the top of the screen and there is no Teletext display. • The antenna setup is inappropriate. 33 • Check the antenna setup. Contact a Sony dealer for advice. – • The channel carries no Teletext broadcast. 18 — Teletext display is • Connection is loose or incomplete the cable is damaged. (snowy picture or • The antenna setup is double images). inappropriate. • Signal transmission is too low. 38 • Check the antenna cable and connection on the TV, VCR and at the wall. • Check the antenna cable and connection on the TV, VCR, and at the wall. 33 • Check the antenna setup. Contact a Sony dealer for advice. – • Display the “Channel Setup” menu and set the “Signal Booster” to “Auto” from “Manual Program”. 30 • Try using an external booster. – • Use the fine tuning (“Fine”) function. 30 Additional Information 01GB08ADV-STMOce.p65 38 Black 10/14/04, 6:08 PM Sony KV-SA32M36 Group F12 (GB)_2-348-392-11 (1) Symptom Possible cause The wide screen • During a transition mode changes between two programs, spontaneously the TV detects the when “Auto Wide” optimum wide screen is “On”. mode. During this Solutions Page 13 — period, an irregular wide screen mode may appear. • The wide screen mode is switched automatically according to the received signal with an ID-1 or WSS signal. 13 — • The Auto Wide feature stops working temporarily when you have pressed , and functions again when the signal format changes. • To fix in the manually selected wide screen mode, set “Auto Wide” to “Off”in the “Wide Screen” menu. 27 The 1 (standby) indicator on your TV flashes red several times after every three seconds. • Your TV’s selfdiagnosis function indicates the possible problems. • Count the number of times the 1 (standby) indicator flashes. Press ! (main power) to turn off your TV. Contact your nearest Sony service center. – The TV screen sometimes goes blank for slightly longer than usual during channel change. • The “Signal Booster” is functioning to detect a weak signal. This does not indicate a malfunction. — – TV cabinet creaks. • Changes in room temperature sometimes make the TV cabinet expand or contract, causing a noise. This does not indicate a malfunction. — – — – A small “boom” sound is heard when the TV is turned on. • The TV’s demagnetizing function is working. This does not indicate a malfunction. Additional Information 01GB08ADV-STMOce.p65 39 Black 10/14/04, 6:08 PM Sony KV-SA32M36 Group F12 (GB)_2-348-392-11 (1) 39 x Specifications KV-SA32M36 KV-SA28M36 Power requirements 220-240 V AC, 50/60 Hz Power consumption (W) Indicated on the rear of the TV Television system B/G, I, D/K, M Color system PAL, PAL 60, SECAM, NTSC3.58, NTSC4.43 Stereo/Bilingual system NICAM Stereo/Bilingual B/G, D/K; A2 Stereo/Bilingual B/G Teletext language English, French Channel coverage B/G VHF : E2 to E12 UHF : E21 to E69 CATV : S01 to S03, S1 to S41 VHF : 0 to 12, 5A, 19A UHF : 28 to 69 CATV : S01 to S03, S1 to S41 Australia only VHF : 1 to 11 UHF : 21 to 69 CATV : S01 to S03, S1 to S41 New Zealand only I UHF : B21 to B68 CATV : S01 to S03, S1 to S41 D/K VHF : C1 to C12, R1 to R12 UHF : C13 to C57, R21 to R60 CATV : S01 to S03, S1 to S41, Z1 to Z39 M 8 (Antenna) VHF : A2 to A13 UHF : A14 to A79 CATV : A-8 to A-2, A to W+4, W+6 to W+84 75-ohm external terminal Audio output (Speaker) 10 W + 10 W Number of terminal (Video) Input: 4 Output: 1 (Audio) Input: 5 Output: 1 (S Video) Input: 2 Phono jacks; 1 Vp-p, 75 ohms Phono jacks; 500 mVrms Y:1 Vp-p, 75 ohms, unbalanced, sync negative C: 0.286 Vp-p, 75 ohms Phono jacks; Y: 1 Vp-p, 75 ohms, sync negative CB: 0.7 Vp-p, 75 ohms CR: 0.7 Vp-p, 75 ohms 120 W max., 8 ohms (Component Video) Input: 1 (Center Speaker) Input: 1 i (Headphone) Note Output: 1 Stereo minijack 32 in. 28 in. Tube size (cm) 81 71 Measured diagonally Screen size (cm) 76 66 Measured diagonally 895 × 575 × 596 786 × 504 × 544 62 45 Picture tube Dimensions (w/h/d, mm) Mass (kg) Design and specifications are subject to change without notice. Sony Corporation 40 Additional Information 01GB08ADV-STMOce.p65 40 Black 10/14/04, 6:08 PM Sony KV-SA32M36 Group F12 (GB)_2-348-392-11 (1)