Transcript
OTHER SYSTEMS OF THE TRIO FAMILY
TRIO CLUB
TRIO MASTER
Subwoofer 10” - 250 mm - VC 50 mm Satellites 2 x 6,5” - 165 mm - VC 32 mm Dome Tweeter- VC 30 mm Power Max/RMS: 1000 / 500 W SPL Max: 121 dB
Subwoofer 15” - 380 mm - VC 75 mm Satellites 2 x 10” - 250 mm - VC 50 mm Horn Compression Tweeter - VC 44 mm Poower Max/RMS: 1440 / 720 W SPL Max: 127 dB
PROFESSIONAL SPEAKERS, AMPLIFIERS AND ACCESSORIES Audiodesign Srl Via dell’industria, 28 - 42025 CAVRIAGO (RE) +39 0522 941444 - Fax +39 0522 942363 www.audiodesign-pro.com
[email protected]
Full Range Sound System
TRIO SESSION User Manual
Portable Full Range Sound System TRIO SESSIO Introduction Thank you for purchasing an AudioDesign TRIO Active Sound system. TRIO series is designed to provide an high and powerful sound quality in a compact size. The main features are: * Active subwoofer cabinet with additional amplifiers for the passive satellites. * High sensitivity passive satellites. * High and precise acoustic quality also with high power. * Portability: the system is easy fit and portable by one person. The final result is a full, detailed and powerful sound. Application The KPRO TRIO systems are a professional solution for every DJ or Live events where high pressure and extreme sound quality is required.
Portable Full Range Sound System TRIO SESSION TECHNICAL SPECIFICATIONS INPUT
SUBWOOFER STAGE PRO W12 LINE IN: Combo Socket XLR 3-F / Jack Stereo INPUT: Balanced and Unbalanced
OUTPUT
SATELLITES OUTPUT: Speakon NL4 (pin 1+ = +, pin 1- = -)
AMPLIFIERS
Subwoofer Power Output: Satellites Power Outputi:
SPEAKER
WEIGHT & SIZES
Precautions: Caution: When using any electric product , precautions should always be taken, including the following: 1) Read carefully all instructions before using the product. 2) To reduce the risk, strict supervision is necessary when the product is used near children. 3) Don't use the product near to water sources like sinks, kitchens, wet floors, pools, or similar or when raining. 4) In case hearing losses or buzzing occur, please contact a doctor. 5) This products should be located so that its position does not interfere or reduce its proper ventilation. 6) This product should be site away from heat sources such as radiators or any other product that generate heat. 7) This product should be connected to a power supply line only of the type described on the operating instructions. Check always the status of the power cable. 8) In case you need to replace the fuse, unplug power supply before replacement. The fuse is located over the power socket and needs to be replaced with a fuse of same type and value. If the fuse blows again, please contact our service. DON'T replace it a second time with a higher value fuse. 9) Unplug power supply when left unused for a long period of time. Don't draw the cable but pull out the plug. 10) Make sure that power switch can always be easily reached. 11) The product needs to be inspected by authorized or qualified personnel in case: A- The power cable or plug are damaged B- Objects or liquids fall inside the product C- The product has been exposed to rain D- The product doesn't appear to operate normally or exhibits a marked change in performance. E- The product has fallen and been damaged. 12) DON'T operate on the product, except indications on the user's manual . Please refer to authorized and qualified personnel for any other operation. 13) Caution: Don't place objects on the product's power cable or place it in a position where it could be damaged or cause interferences. Improper installation could cause fire risk and/or personal injury.
INPUT SPEAKERS MAIN FEATURES
WEIGHT & SIZES
300 W RMS 2x170 W RMS
@ 4 Ohm Load
Electronic Crossover LP Subwoofer: Frequency 46 - 240 Hz / 12 dB/Oct. Electronic Crossover HP Satellites: Frequency 38 - 250 Hz / 12 dB/Oct. Subwoofer: 1 x 12” (320 mm) VC 65 mm Frequency Response: 30 ÷ 260 Hz (± 3 dB) SPL Max: Max: 124 123 dB SPL
Weight Subwoofer: Sizes (WxLxH) cm:
38 kg 52 x 47 x 48
SATELLITE STAGE PRO 8 SATELLITES INPUT: Speakon NL4 (pin 1+ = +, pin 1- = -) (200 mm) 1 x 8” High Sensitivity Woofer VC 34 mm Compression Horn Tweeter TOTAL IMPEDANCE : TOTAL POWER : TOTAL SPL Max: Frequency Response: Tweeter Crossover: Weight Satellite: Size (WxLxH) cm:
VC 50 mm
4 Ohm 200 W RMS (400 W Max) with X-over 200 Hz 18 dB/oct 124 dB 75 ÷ 20000 Hz (± 3 dB) 12 dB/oct Passive 6000 Hz 9 kg 27 x 26 x 40
BY MEANS OF OUR ACCESSORIES, DIFFERENT CONFIGURATIONS OF THE SYSTEM ARE POSSIBLE
Service All Audio Design PRO products have been inspected and tested before leaving the factory and , if properly used, they will work for many years. However, in case of any problem, please proceed in the following way: Contact your dealer and inform about the defect you found In case it won't be possible to solve the problem with the dealer, the product needs to be returned, preferably in its original packaging or in a proper packing to protect it during the transport. Purchase documents must be produced too. Your dealer will arrange the shipment to our service centre. Conformity: Audiodesign Pro products comply with presently existing - 2 - directives and standards.
(600 W Max) (2x340 W Max)
-7-
Portable Full Range Sound System TRIO SESSIO
Portable Full Range Sound System TRIO SESSION 6
Volume setting of the system is made by means of the three LEVEL knobs on top of the subwoofer: 6 - Left satellite is GAIN LEFT 6 - Right satellite is GAIN RIGHT - Subwoofer is GAIN SUBWOOFER 3
PEAK
L
GAIN
HIGH
HI PASS
80
120
60 50
Hz
260
+15
0
10
50
Hz
GAIN
GAIN
HIGH
HI PASS 80
PHASE SHIFT 120
60 -15
Thi TRIO SESSION stereo system is composed by three elements:
PEAK
PEAK LOW PASS
80
SYSTEM COMPONENTS
6
3
0 - 180°
260
0
10
10
-15
+15
50
Hz
260
POWER
LEFT speaker
Subwoofer
1 Active Subwoofer STAGE PRO W12 2 Passive Satellites STAGE PRO 8
120
60 0
R
Active Subwoofer STAGE PRO W12
R IGHT speaker
Before switching power on and proceed to system setting, make sure that all three knobs are completely turned counterclockwise, at level 0, and that the mixer output is set so that the peaks level stays about within 0 e +3 dB.
The active subwoofer STAGE PRO W12 is equipped with a 12" (320 mm) woofer with 65 mm VC. The cabinet integrates all necessary electronics for amplification and system processing:
Set first the satellites volume alone and then the subwoofer volume alone.
3 amplifiersi in AB Class for a total power of 640 W RMS (12840 W Max)
Satellites Volume setting
1 x 300 W RMS (600 W Max) for the Subwoofer itself 2 x 170 W RMS (340 W Max) for the two passive satellites (@ 4 Ohm load)
Switch power on and begin to turn clockwise the satellite GAIN knobs 6 until the correspondent PEAK led begins to flash shortly for less than 1 second. This is the optimal level being connected to a mixer sending to MAIN a signal with level peaks within 0 and +3dB.
The Subwoofer signal is LowPass filtered, adjustable from 46 to 240 Hz 12 dB/oct. The Satellites signals are HighPass filtered, adjustable from 38 to 250 Hz 12 dB/oct.
Now listen to the satellites with this output level; if you detect distorsion or saturation of the signal (i.e of microphone) check the possibility of reducing the level of the signal concerned at his source, otherwise try to slightly lower the mixer’s main otput. Should this not be enough, reduce the satellites volume until you have an optimal sound. Memorize the knobs setting.
Cabinet of high density MDF, anti-scratch embossed painting Practical transport handles hollowed into the wood Integral rigid metal grill
Sub Volume setting
Housing hole for ø 35 mm stand tubes
After having memorized the knobs setting LEFT e RIGHT, take them back to 0 and begin now to turn clockwise the SUBWOOFER GAIN knob 3 until the correspondent PEAK led begins to flash shortly for less than 1 second. This is the optimal level being connected to a mixer sending to MAIN a signal with level peaks within 0 and +3dB.
Sizes & weight: 52 x 47 x 48 cm; 38 kg.
Now listen to the Sub with this output level; if you detect distorsion of basses, turn slightly the knob back counterclokwise.
Connections and Control Panels
Final system setting Bring the three knobs at the optimal level you have checked and listen to the complete system, again at the mixer main level peaks between 0 and +3 dB. If you detect to much basses compared with satellites output, turn slightly back the SUB LEVEL knob. If you detect instead not enough basses, turn slightly back the setellites LEVEL LEFT and RIGHT knobs.
2 Subwoofer LOW PASS control adjustable from 46 to 250 Hz
2 1 3
8 7 6 5 PEAK
L
-6-
HI PASS
GAIN
HIGH
80
120 50
Hz
260
+15
0
10
50
Hz
GAIN
HIGH
R
HI PASS 80
0 - 180°
260
3 Subwoofer Volume control
PEAK GAIN
PHASE SHIFT 120
60 -15
5 6 7 8
PEAK LOW PASS
80
60
0
10
10
-15
+15
LEFT speaker
Subwoofer
4 Phase Switch 0-180°
120
60 0
50
Hz
260
POWER
As a general rule , the output level of the mixers should be set so that the sound peaks remain between 0 to +3 dB about. When the system TRIO MASTER gets in the two Line In (10 and 11) a signal with that amplitude and it is set as explained above, it grants the maximum performance in terms of maximum undistorted amplification (at clip limit) and in this conditions you get the maximum possible sound pressure (SPL).
1 Subwoofer Clip Indicator
R IGHT speaker
4
9
5 Satellites Clip Indicator (Separated Left and Right) 6 Satellites Volume control separated on channel LEFT and RIGHT.
it controls only the signal going respectively to left and right satellite. 13
12
18
7 High tones equalization separated for left and right channel -15 / +15 dB
11 10
8 Satellites HI PASS control separated LEFT and RIGHT from 38 to 250 Hz
ATTENTION: the HI PASS frequency should not be set under 120 Hz
RESPONSE DIAGRAM TRIO SESSION
LINE IN
OUTPUT OUT+:1+/ OUT- :1-
Sensitivity Magnitude
- dB SPL/watt (4 ohm load)
@ 1W/1m
9 ON LED indicator (Red)
ST MONO
M L S S A
90.0
RIGHT
LEFT
RIGHT
GND=1=SLEEVE HOT=2=TIP COLD=3=RING
10 Right Channel Line In
Combo Socket XLR 3-F / Jack 6,3 mm Balanced 11 Left Channel Lin In
Combo Socket XLR 3-F / Jack 6,3 mm Balanced
USE ONLY WITH 250V FUSE
85.0
LEFT
SPEAKER OUTPUT: 180W@4Ù
220
95.0
80.0
12 Speakon Socket Right Satellite
75.0
13 Speakon Socket Left Satellite
70.0
14
Amplifier cooling fan; keep it clean for a correct ventilation.
65.0
15 On/Off power switch - In positioe 0 the system is Off 60.0
16 Voltage Selector
55.0 50.0
14
15
16
17
17 Power Net Socket 18 ST/MONO Switch (Stereo / Mono): se si seleziona STEREO,
45.0 aut o
20.0
100.0
AUDIODESIGN PRO: TRIO SESSION
1000.0
log Frequency - Hz -6-
10000.0
MLSSA: Frequency Domain
When STEREO is selected, the system sends to the Right and Left channels the correspondent Right and Left input signals. When MONO is selected, the system sends to both Right and Left channels only the LEFT input signal, so one complete system per channel can be used.. -3-
Portable Full Range Sound System TRIO SESSIO
Portable Full Range Sound System TRIO SESSION
High sensitivity passive satellites STAGE PRO 8 CONNECTION OF TWO SYSTEMS IN MONO CONFIGURATION The high sensitivity passive satellite STAGE PRO 8 is a bass reflex cabinet equipped with:
(ST/MONO Switch down)
RIGHT CHANNEL
LEFT CHANNEL
One 8" (200 mm) woofer with a 50 mm vented voice coil
LEFT/ MONO
RIGHT
1
MIC 2
MIC 3
MIC 4
MIC 5
INPUT OUTPUT CD/TAPE
1
2
MIC 1
PAM
2
FX
X 2 .6 2
ULTRALOW-NOISE DESIGN 14-INPUT 2/2-BUS MIC/LINE MIXER WITH PREMIUM MIC PREAMPLIFIERS AND DIGITAL 24-BIT MULTI-EFFECTS PROCESSOR USB AUDIO INTERFACE
MIC 6 AUX SENDS
24-BIT MULTI-FX PROCESSOR 80 CHORUS & REVERB 82 FLANGER & REVERB 84 PHASER & REVERB 86 PITCH & REVERB 88 DELAY & REVERB 90 DELAY & GATED 91 DELAY & REVERSE 92 DELAY & CHORUS 94 DELAY & FLANGER 96 DELAY & PHASER 98 DELAY & PITCH
36 REVERSE 40 EARLY REFL 44 AMBIENCE 48 STADIUM 49 AMBIENCE FX 50 DELAY 59 ECHO 60 CHORUS 66 FLANGER 70 PHASER 74 PITCH SHIFT
00 SMALL HALL 03 MID HALL 06 BIG HALL 09 CHURCH 10 SMALL ROOM 13 MID ROOM 16 BIG ROOM 19 CHAPEL 20 SPRING 27 SPRING 30 GATED REV
One compression horn tweeter with a 34 mm voice coil
USB INTERFA
LINE IN 5/6
High Pass Filter at 6000 Hz 12 dB/oct on tweeter
LAM
LINE IN 7/8
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
HIGH
HIGH
HIGH
HIGH
HIGH
HIGH
HIGH
HIGH
12 kHz
12 kHz
12 kHz
12 kHz
12 kHz
12 kHz
12 kHz
12 kHz
MID
MID
2.5 kHz
MID
2.5 kHz
MID
2.5 kHz
MID
2.5 kHz
MID
2.5 kHz
MID
2.5 kHz
P
12V 400
PROGRAM ( PUSH )
MID
2.5 kHz
2.5 kHz
AUX SENDS
1 LOW
LOW
80 Hz
LOW
80 Hz
LOW
80 Hz
LOW
80 Hz
LOW
80 Hz
LOW
80 Hz
CE
mA
STEREO AUX RETURNS
1
1 TO AUX
LOW
80 Hz
80 Hz
SEND 1
SOLO
4 ohm Impedance
1
AUX
1
AUX
1
AUX
1
AUX
1
AUX
1
AUX
1
AUX
1
AUX
2
PRE
2
PRE
2
PRE
2
PRE
2
PRE
2
PRE
2
PRE
2
PRE
2
2
FX
FX
MAIN MIX ALT 3-4
SOLO
2-TR/USB TO MAIN 2-TR/USB
FX
FX
FX
FX
FX
FX
FX
FX
PAN
PAN
PAN
PAN
PAN
PAN
BAL
BAL
10 5
ALT 3-4
2
MAX
PHONES/CTRL R
0 2
MAIN MIX
Speakon socket for connection to the subwoofer amplifier
MAIN SOLO
PFL
5
SOURCE
1
2
MUTE
3
MUTE
ALT 3-4
MUTE
MUTE
ALT 3-4
dB
MUTE
5
4
MUTE
ALT 3-4
dB
MUTE
6
MUTE
ALT 3-4
dB
MUTE
7/8
MUTE
ALT 3-4
dB
MUTE
9/10
MUTE
ALT 3-4
dB
MUTE
dB
20
MUTE
ALT 3-4
dB
ALT 3-4
MUTE
dB
3
4
MUTE
CLIP
CLIP
CLIP
CLIP
CLIP
CLIP
CLIP
CLIP
SOLO
SOLO
SOLO
SOLO
SOLO
SOLO
SOLO
SOLO
MODE
SOLO (NORMAL) PFL (LEVEL SET)
L
R
Cabinet in high density MDF , embossed anti-scratch painting Integral protection grill
1
2
3
4
5
6
7/8
9/10
AL T 3-4
MAIN MIX
Housing hole for ø 35 mm stand tubes Sizes and Weight: 27 x 26 x 40 cm; 9 kg.
LINE IN
OUTPUT OUT+:1+/ OUT- :1-
LINE IN
OUTPUT OUT+:1+/ OUT- :1-
ST MONO ST MONO
LEFT
LEFT(Mono)
RIGHT
SPEAKER OUTPUT:
LEFT
LEFT(Mono)
RIGHT
SPEAKER OUTPUT:
RIGHT
GND=1=SLEEVE HOT=2=TIP COLD=3=RING
RIGHT
GND=1=SLEEVE HOT=2=TIP COLD=3=RING
220 LEFT/ MONO
RIGHT
1
MIC 2
MIC 3
MIC 4
MIC 5
INPUT OUTPUT CD/TAPE
1
2
MIC 1
PAM
2
FX
USE ONLY WITH 250V FUSE
SYSTEM CONNECTION IN STEREO CONFIGURATION (ST/MONO Swich up)
USE ONLY WITH 250V FUSE
220
NET
X 2 .6 2
ULTRALOW-NOISE DESIGN 14-INPUT 2/2-BUS MIC/LINE MIXER WITH PREMIUM MIC PREAMPLIFIERS AND DIGITAL 24-BIT MULTI-EFFECTS PROCESSOR USB AUDIO INTERFACE
MIC 6 AUX SENDS
24-BIT MULTI-FX PROCESSOR 80 CHORUS & REVERB 82 FLANGER & REVERB 84 PHASER & REVERB 86 PITCH & REVERB 88 DELAY & REVERB 90 DELAY & GATED 91 DELAY & REVERSE 92 DELAY & CHORUS 94 DELAY & FLANGER 96 DELAY & PHASER 98 DELAY & PITCH
36 REVERSE 40 EARLY REFL 44 AMBIENCE 48 STADIUM 49 AMBIENCE FX 50 DELAY 59 ECHO 60 CHORUS 66 FLANGER 70 PHASER 74 PITCH SHIFT
00 SMALL HALL 03 MID HALL 06 BIG HALL 09 CHURCH 10 SMALL ROOM 13 MID ROOM 16 BIG ROOM 19 CHAPEL 20 SPRING 27 SPRING 30 GATED REV
USB INTERFA
LINE IN 5/6
LEFT CHANNEL
LAM
LINE IN 7/8
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
HIGH
HIGH
HIGH
HIGH
HIGH
HIGH
HIGH
HIGH
12 kHz
12 kHz
12 kHz
12 kHz
12 kHz
12 kHz
12 kHz
12 kHz
P
12V 400
CE
mA
RIGHT CHANNEL PROGRAM ( PUSH )
MID
MID
MID
MID
MID
MID
MID
MID
2.5 kHz
2.5 kHz
2.5 kHz
2.5 kHz
2.5 kHz
2.5 kHz
2.5 kHz
2.5 kHz
LOW
LOW
LOW
LOW
LOW
LOW
LOW
LOW
80 Hz
80 Hz
80 Hz
80 Hz
80 Hz
80 Hz
80 Hz
80 Hz
AUX SENDS
STEREO AUX RETURNS
1
1
1 TO AUX SEND 1
SOLO 1
AUX
1
AUX
1
AUX
1
AUX
1
AUX
1
AUX
1
AUX
1
AUX
2
PRE
2
PRE
2
PRE
2
PRE
2
PRE
2
PRE
2
PRE
2
PRE
2
2
FX
FX
MAIN MIX ALT 3-4
SOLO
2-TR/USB TO MAIN 2-TR/USB
FX
FX
FX
FX
FX
FX
FX
10
FX
5
ALT 3-4
PAN
PAN
PAN
PAN
PAN
BAL
0
BAL 2
MAIN MIX MAIN SOLO
PFL
5
SOURCE
1
2
MUTE
3
MUTE
ALT 3-4
MUTE
MUTE
MUTE
6
MUTE
ALT 3-4
dB
MUTE
7/8
MUTE
ALT 3-4
dB
MUTE
9/10
MUTE
ALT 3-4
dB
MUTE
dB
20
MUTE
ALT 3-4
dB
ALT 3-4
MUTE
3
dB
CLIP
CLIP
CLIP
CLIP
CLIP
CLIP
CLIP
CLIP
SOLO
SOLO
SOLO
SOLO
SOLO
SOLO
SOLO
SOLO
2
3
4
5
7/8
6
4
MUTE
9/10
MODE
SOLO (NORMAL) PFL (LEVEL SET)
L
R
Connection to the electric net AL T 3-4
Check that Power switch 15 is in position 0 and that net voltage corresponds to the one selected in the system. Connect the supplied electric wire to an electric net socket equipped with a correct ground contact.
MAIN MIX
.
.
Satellite connection Use wires with good quality Speakon plugs. Make sure to rotate the Speakon plugs clockwise up to the lock position.
Connection to the mixer LINE IN
OUTPUT
Before making any connection to the mixer make sure the system power switch is Off in order to avoid damages. Remember that electric net power il the last to be switced On and the first to be disconnected after use!
OUT+:1+/ OUT- :1-
ST MONO
LEFT
LEFT(Mono)
RIGHT
SPEAKER OUTPUT:
RIGHT
GND=1=SLEEVE HOT=2=TIP COLD=3=RING
System Volume setting USE ONLY WITH 250V FUSE
220
1
MUTE
ALT 3-4
dB
5
4
MUTE
ALT 3-4
dB
Depending on the choosen configuration, connect the system following the precedent wiring schemes.
2
MAX
PHONES/CTRL R
PAN
NET
The TRIO MASTER system is provided vith clip limiters and peack level indicators separate and independent on all three channels, and doesn’t require therefore any special setting procedure. Thus the system is able to deliver excellent performances, and should be used with input signals at optimal level, starting from kind and quality of the used cables, and the prevention of any kind of distortion. In fact the presence of distortion doesn’t only deliver a poor performance of the system, but it is also a real risk on long periods, to damage the system itself. We kindly invite you therefore,to strictly follow the following instructions on how to set the level of alla comonents.
-4-
-5-
