Transcript
Optoway
TRSL-7110CG
1
***********************************************************************************************************************************************************************
TRSL-7110CG / TRSL-7110ACG / TRSL-7110G / TRSL-7110AG 3.3V / 1310 nm / 1.25 Gbps RoHS Compliant SFF LC SINGLE-MODE TRANSCEIVER **********************************************************************************************************************************************************************
DESCRIPTION
FEATURES l l l l l l l l l l l l l l l l
Duplex LC Single Mode Transceiver IEEE 802.3z 1000BASE-LX Compliant Fiber Channel 1X SM-LC-L FC-PI Compliant Small Form Factor, RJ-45 size, 2X5 pin Package 1310 nm LD Transmitter 10 km Transmission at Least AC/AC Coupled Signal Input / Output LVTTL Transmitter Disable Input LVTTL Signal Detect Output: TRSL-7110CG LVPECL Signal Detection Output: TRSL-7110G Single +3.3 V Power Supply RoHS Compliant 0 to 70oC Operation: TRSL-7110CG -40 to 85oC Operation: TRSL-7110ACG Wave Solderable and Aqueous Washable Class 1 Laser International Safety Standard IEC-60825 Compliant
APPLICATIONS
l Gigabit Ethernet Switches and Routers l Fiber Channel Switch Infrastructure l Metro Edge Switching
The TRSL-7110CG series single mode transceivers is small form factor, low power, high performance module for bi-directional serial optical data communications such as IEEE 802.3z Gigabit Ethernet 1000BASE-LX and Fiber Channel 1X SM-LC-L FC-PI. This module is designed for single mode fiber and operates at a nominal wavelength of 1310 nm. The transmitter section uses a multiple quantum well laser and is a class 1 laser compliant according to International Safety Standard IEC-60825. The receiver section uses an integrated InGaAs detector preamplifier (IDP) mounted in an optical header and a limiting post-amplifier IC. A LVPECL logic interface simplifies interface to external circuitry.
LASER SAFETY This single mode transceiver is a Class 1 laser product. It complies with IEC-60825 and FDA 21 CFR 1040.10 and 1040.11. The transceiver must be operated within the specified temperature and voltage limits. The optical ports of the module shall be terminated with an optical connector or with a dust plug.
ORDER INFORMATION P/No. TRSL-7110CG TRSL-7110ACG
Bit Rate (Gb/s) 1.25/1.063 1.25/1.063
1000 BASE LX/LH LX/LH
Distance (km) 10 10
Wavelengt h (nm) 1310 1310
Package 2X5 LC 2X5 LC
Temp. (oC) 0 to 70 -40 to 85
TX Power RX Sens. RoHS (dBm) (dBm) Compliant -3 to -9.5 -20 Yes -3 to -9.5 -20 Yes
Absolute Maximum Ratings Parameter Storage Temperature Operating Temperature
Symbol Tstg Topr
Soldering Temperature Power Supply Voltage Input Voltage
--Vcc ---
Output Current
Iout
Min -40 0 -40
Units o C o C
0 GND
Max 85 70 85 260 4.5 Vcc
0
30
mA
Min 3.13 0 -40 1000
Typ 3.3
Max 3.47 70 85
o
C V V
Notes TRSL-7110CG TRSL-7110CAG 10 seconds on leads only
Recommended Operating Conditions Parameter Power Supply Voltage Operating Temperature
Symbol Vcc Topr
Data Rate Power Supply Current
Icc
1250 200
250
Units / Notes V o C / TRSL-7110CG o C / TRSL-7110CAG Mb/s mA
***********************************************************************************************************************************************************************
OPTOWAY TECHNOLOGY INC. No.38, Kuang Fu S. Road, Hu Kou, Hsin Chu Industrial Park, Hsin Chu, Taiwan 303 Tel: 886-3-5979798 Fax: 886-3-5979737 E-mail:
[email protected] http: // www.optoway.com.tw
12/1/2005 V2.0
Optoway
TRSL-7110CG
2
***********************************************************************************************************************************************************************
Transmitter Specifications (0 oC < Topr < 70 oC, 3.13V < Vcc < 3.47V) Parameter Optical Optical Transmit Power Output Center Wavelength Output Spectrum Width Extinction Ratio Output Eye Optical Rise Time Optical Fall Time Relative Intensity Noise Total Jitter Electrical Data Input Current – Low Data Input Current – High Differential Input Voltage Data Input Voltage – Low Data Input Voltage -- High Disable Input Voltage -- Low Disable Input Voltage -- High Shut Off Time for TxDis
Symbol
Min
Typ
Max
Units
Notes
Po -9.5 1274 λ --∆λ ER 9 Compliant with IEEE 802.3z tr tf RIN TJ
--1310 -----
-3 1356 2.5 ---
dBm nm nm dB
1
0.26 0.26 -120 0.227
ns ns dB/Hz ns
IIL IIH VIH - V IL VIL - V CC VIH - V CC VTDIS,L VTDIS,H tDIS
-350 350 300 -2.0 -1.1 0 Vcc – 1.3
-1.58 -0.74 0.5 Vcc 1
µA µA mV V V V V ms
RMS (σ)
20% to 80% Values 20% to 80% Values 2
3 3 TX Output Enabled TX Ouput Disabled
Notes: 1. Output power is power coupled into a 9/125 µm single mode fiber. 2. Measured with a 27-1 PRBS. 3. These inputs are compatible with 10K, 10KH and 100K ECL and PECL inputs.
Receiver Specifications (0oC < Topr < 70oC, 3.13V < Vcc < 3. 47V) Parameter Optical Sensitivity Maximum Input Power Signal Detect -- Asserted Signal Detect -- Deasserted Signal detect -- Hysteresis Wavelength of Operation Electrical Data Output Voltage – Low Data Output Voltage – High Signal Detect Output Voltage -- Low Signal Detect Output Voltage -- High Signal Detect Output Voltage -- Low Signal Detect Output Voltage -- High
Symbol
Min
Typ
Max
Units
Notes
--Pin Pa Pd
---3 ---31 1.0 1100
---
-20 ---20 ---
dBm dBm dBm dBm dB nm
1
VOL - VCC VOH - VCC VOL VOH VOL - VCC VOH - VCC
-2.0 -1.1 2.0 -2.0 -1.1
---------
1600 -1.58 -0.74 0.5 -1.58 -0.74
V V V V V V
Transition: low to high Transition: high to low
2 2 TRSL-7110CG TRSL-7110G
Notes: 1. Minimum sensitivity and saturation levels at BER=1E-12 for a 27-1 PRBS. 2. These outputs are compatible with 10K, 10KH and 100K ECL and PECL outputs.
***********************************************************************************************************************************************************************
OPTOWAY TECHNOLOGY INC. No.38, Kuang Fu S. Road, Hu Kou, Hsin Chu Industrial Park, Hsin Chu, Taiwan 303 Tel: 886-3-5979798 Fax: 886-3-5979737 E-mail:
[email protected] http: // www.optoway.com.tw
12/1/2005 V2.0
Optoway
TRSL-7110CG
3
***********************************************************************************************************************************************************************
CONNECTION DIAGRAM
PIN 1 2 3 4 5 6 7 8
Symbol VEEr VCC r SD RD− RD+ VCC t VEEt TDis
9 10 MS
TD+ TDMS
Notes Directly connect this pin to the receiver ground plane +3.3V dc power for the receiver section Active high on this indicates a received optical signal. Receiver Dataout Bar. See recommended circuit schematic Receiver Dataout. See recommended circuit schematic +3.3V dc power for the transmitter section Directly connect this plan to the transmitter ground plane Transmitter Disable. Connect this pin to +3.3V TTL logic “1” to disable module To enable module connect to TTL logic low “0” Transmitter Data In. See recommended circuit schematic Transmitter Data In Bar. See recommended circuit schematic Mounting Studs. Connect to Chassis Ground
RECOMMENDED CIRCUIT SCHEMATIC Vcc3.3V
TDZ=50R
LVPECL
TD+
TDTD+ TDis Veet Vcct
TXDis(LVTTL)
10 9 8 7 6
Z=5OR
Vcc3.3V
1uH
10nF
10nF
10uF
10uF
PHY DEVICE
1 2 3 4 5
Veer Vccr SD RDRD+
1uH
10nF
Vcc3.3V
10uF
RD+
100R
LVPECL
Z=50R
RDZ=5OR
SD
TO LVTTL STAGE
Note: 1. TX input is terminated inside the module. 2. 1000ΩSD Output pull-down resistor required for TRSL-7XX0G / TRSL-7XX0AG (LVPECL SD Output). 3. Veer and Veet are not internally connected to each other. 4. 50 Ω line pattern and component placements on TD+/TD- and RD+/RD- lines shall be symmetrical for better impedance matching. ***********************************************************************************************************************************************************************
OPTOWAY TECHNOLOGY INC. No.38, Kuang Fu S. Road, Hu Kou, Hsin Chu Industrial Park, Hsin Chu, Taiwan 303 Tel: 886-3-5979798 Fax: 886-3-5979737 E-mail:
[email protected] http: // www.optoway.com.tw
12/1/2005 V2.0
Optoway
TRSL-7110CG
4
***********************************************************************************************************************************************************************
PACKAGE DIAGRAM Units in mm
1) Standard Case
TRSL-7110G / TRSL-7110AG / TRSL-7110CG / TRSL-7110CAG 2) Extended Case
TRSL-7110EG / TRSL-7110AEG / TRSL-7110CEG / TRSL-7110CAEG Note: Specifications subject to change without notice. ***********************************************************************************************************************************************************************
OPTOWAY TECHNOLOGY INC. No.38, Kuang Fu S. Road, Hu Kou, Hsin Chu Industrial Park, Hsin Chu, Taiwan 303 Tel: 886-3-5979798 Fax: 886-3-5979737 E-mail:
[email protected] http: // www.optoway.com.tw
12/1/2005 V2.0
