Transcript
14D1-S/G/W 14D2-S/G
SERVICE MANUAL SX2T914D-1S//
SERVICE MANUAL
COLOUR TELEVISION
Chassis No. GA-1AM 14D1-S/G/W
14D2-S/G
COLOUR TELEVISION
MODELS
14D1-S/G/W 14D2-S/G
In the interests of user-safety (Required by safety regulations in some countries) the set should be restored to its original condition and only parts identical to those specified should be used.
FEATURES Ë Ë Ë Ë Ë Ë Ë Ë
Multi 18 systems Full Auto Channel Preset and Auto Channel Skip 100-CH Program Memory CATV(Hyper Band) Ready AVL(Sound Keeper) Function Black Stretch Circuit On Timer/Sleep Timer/Reminder Timer Blue Back Noise Mute
Ë Front Headphone Terminal Ë Front AV-In & Rear AV-In/Out Terminals (Front Priority) Ë Colour Comb Filter(NTSC only) Ë High Contrast Picture Ë Hotel Mode Ë Arabic/Chinese/English/French/Malay/Russian 6 Languages OSD Ë White Temperature Adjustment
CONTENTS MODELS 14D1-S/G/W, 14D2-S/G
» » » » » » » » » » » »
Page SPECIFICATIONS ............................................. 2 IMPORTANT SERVICE NOTES ........................ 2 ADJUSTMENT PRECAUTIONS ........................ 3 MEMORY MAP ................................................ 11 GA1 HOTEL MODE APPLICATION ................ 15 TROUBLE SHOOTING TABLE ........................ 15 WAVEFORMS .................................................. 18 SOLID STATE DEVICE BASE DIAGRAM ....... 20 CHASSIS LAYOUT .......................................... 21 BLOCK DIAGRAM ........................................... 23 DESCRIPTION OF SCHEMATIC DIAGRAM .. 28 SCHEMATIC DIAGRAM Ë CRT UNIT ..................................................... 29
Page Ë HEAD PHONE UNIT .................................... 29 Ë MAIN UNIT ................................................... 30 » PRINTED WIRING BOARD ASSEMBLIES ..... 34 » REPLACEMENT PARTS LIST Ë ELECTRICAL PARTS MAIN UNIT ................................................... 39 CRT UNIT ..................................................... 42 HEAD PHONE UNIT .................................... 43 Ë SUPPLIED ACCESSORIES ......................... 43 Ë PACKING PARTS ......................................... 43 Ë CABINET PARTS ......................................... 44 » PACKING OF THE SET ................................... 45
WARNING The chassis in this receiver is partially hot. Use an isolation transformer between the line cord plug and power receptacle, when servicing this chassis. To prevent electric shock, do not remove cover. No user – serviceable parts inside. Refer servicing to qualified service personnel.
SHARP CORPORATION 1
2 2-1
Specifications are subject to change without prior notice.
Cabinet material .................................................................................... All Plastics
Dimensions 14D1-S/G/W ............................................................................. Width: 357.0mm Height: 364.0mm Depth: 370.5mm Weight(approx): 9.5 kg 14D2-S/G .................................................................................. Width: 446.0mm Height: 333.0mm Depth: 362.0mm Weight(approx): 9.2 kg
Tuner Ranges VHF-Channels .......................................... E2(48.25MHz) thru E12(224.25MHz) C1(49.75MHz) thru C12(216.25 MHz) S1(105.25MHz) thru S36(423.25HMz) UHF-Channels ...................................... E21(471.25MHz) thru E69(855.25MHz) C13(471.25MHz) thru C57(863.25MHz) S37(431.25MHz) thru S41(463.25MHz)
Aerial Input Impedance VHF/UHF .......................................................................... 75 ohms Unbalanced Receiving System .................................................... CCIR SECAM/PAL B, G,D,K,I
2-2
1. Inspect all lead dress to make certain that leads are not pinched or that hardware is not lodged between the chassis and other metal parts in the receiver. 2. Inspect all protective devices such as non-metallic control knobs, insulating fishpapers, cabinet backs, adjustment and compartment covers or shields, isolation resistor- capacity networks, mechanical insulators etc.
Before returning the receiver to the user, perform the following safety Checks.
BEFORE RETURNING THE RECEIVER
1. When repairing the circuit, be sure not to increase the high voltage to more than 23.7kV(at beam 0 µA) for the set. 2. To keep the set in a normal opeartion , be sure to make it function on 22.5kV±1.5kV(at beam 800 µA) in the case of the set. The set has been factory - Adjusted to the abovementioned high voltage. * If there is a possibility that the high voltage fluctuates as a result of the repairing, never forget to check for such high voltage after the work. 3. Do not substitute a picture tube with unauthorizerd types and/or brands which may cause excess X-ray radiation.
This receiver is designed so that any X-Ray radiation is kept to an absolute Minimum. Since certain malfunctions or servicing may produce potentially hazardous radiation with prolonged exposure at close range, the following precautions should be observed:
X-RAY
Speaker Size 14D1-S/G/W .................................................................. 5 x 9 cm Elliptic (1pc) 14D2-S/G .................................................................... 5 x 9 cm Elliptic (2 pcs) Voice Coil Impedance ........................................................... 16 ohms at 400 Hz
Picture tube in this receiver employs integral implosion protection. Replace with tube of the same type number for continued safety. Do not lift picture tube by the neck. Handle the picture tube only when wearing shatterproof goggles and after discharging the high voltage completely.
1. 2. 3. 4.
When servicing the high voltage system, remove static charge from it by Connecting a 10K ohm Resistor in series with an insulated wire(such as a test probe) between picture tube dag and 2nd anode lead. (AC line cord should be disconnected from AC outlet.)
SERVICE OF HIGH VOLTAGE SYSTEM AND PICTURE TUBE
Maintenance and repairing of this receiver should be done by qualified service personnel only.
IMPORTANT SERVICE NOTES
Audio Power Output Rating 14D1-S/G/W ................................................................................. 3.0W(at Max.) 14D2-S/G ...................................................................................... 5.0W(at Max.)
Power Input ..................................................................... 110 ~ 240V AC 50/60 Hz Power Consumption 14D1-S/G/W ................................................................................................ 58W 14D2-S/G ..................................................................................................... 62W
Sweep Deflection ...................................................................................... Magnetic Intermediate Frequencies Picture IF Carrier .................................................................................. 38.9MHz Sound IF Carrier Frequency 6.5MHz .............................................................................................. 32.4MHz 6.0MHz .............................................................................................. 32.9MHz 5.5MHz .............................................................................................. 33.4MHz Colour Sub-Carrier Frequency ............................................................ 34.47MHz
Convergence ................................................................. Self Convergence System Focus ...................................................................... Quadra-Potential Electrostatic
SPECIFICATIONS
14D1-S/G/W 14D2-S/G
3 3-1
3. For reference please check with memory map (GA-1AM Series type RH-IX3368CE Attachment)
Precaution: If haven't done this initiation, it may possibly generate excessive Beam current.
Note: Once the chassis has been assembly together and ready to be POWER ON for the FIRST TIME, make sure to short JA137 & JA138 to switch to the service mode position first and then turn on the main power switch (See 2-(1) above).
3. Make sure the data need modify or not (Initial data).
2. The initial data are preset as listed in page 8, 9, & 10.
1.Short JA 137 & JA 138 then turn "ON" the main power and release to switch to the Service Mode position.Initial values are automatically preset, only when a new EEPROM is used (Judge with the first 4 bytes ).
2. Factory Presetting.
5. Short JA 137 & JA 138 for 1 second and release to switch to the normal mode (OFF) position, and the microprocessor is in out of the service mode.
4. Using the VOLUME UP/ DOWN key on the remote controller, the data can be modified.
3. Press the CH DOWN / UP key on the remote controller to select the modes reversibly one by one.
2. Press the CH DOWN / UP key on the remote controller to get ready to select the mode one by one.
1. Short JA 137 & JA 138 for 1 second and release to switch to the service mode position, and the microprocessor is in input mode. (Adjustment through the I2C bus control). (Use JWS Key to set as well).
1. Setting the service mode by the microprocessor.
This model's setting are adjusted in two different ways: through the I2C bus control and in the conventional analog manner. The adjustments via the I2C bus control include preset-only items and variable data. CAUTION: Make sure TV Set is in "Normal Condition" before switch to Service Mode for adjustment.
ADJUSTMENT PRECAUTIONS
3-2
↓ W.P RED STD. W.T. (DRI-RS) ↓ W.P. GREEN STD. W.T.(DRI-GS) ↓ W.P.BLUE STD. W.P. (DRI-BS) ↓ W.P. RED WARM W.P.(DRI-RC) ↓ W.P. GREEN WARM W.P.(DRI-GC) ↓ W.P. BLUE WARM W.P.(DRI-BC) ↓ W.P. RED COOL W.P.(DRI-RW) ↓ W.P. GREEN COOL W.P.(DRI-GW) ↓ W.P. BLUE COOL W.P. (DRI-BW)
↓ AGC TAKE OVER POINT (AGC) ↓ VERTICAL SLOPE (V-LIN) ↓ VERTICAL AMP (V-AMP) ↓ VERTICAL SHIFT (V-CENT) ↓ HORIZONTAL SHIFT (H-CENT) ↓ EAST-WEST WIDTH (H-SIZE) ↓ HORIZONTAL PARALLELOGRAM (EW//) ↓ EAST-WEST PARABOLA/WIDTH (PARA) ↓ EAST-WEST UPPER COR. PB (LOR(U)) ↓ EAST-WEST LOWER COR. PB (COR(L)) ↓ EAST-WEST TRAPEZIUM (TRAPE) ↓ HORIZONTAL BOW (HB) ↓ S-CORRECTION (S-COR) FORWARD : CH DOWN KEY REVERSE : CH UP KEY *( ) means OSD display.
WHITE POINT ADJ. MODE
IC OPTION MODE
WHITE POINT ADJ. MODE
AGC & GEOMETRIC MODE
MISC. OPTION MODE
AGC & GEOMETRIC MODE
(1) In the Service Mode, Key is used to select the mode in the following order.
SERVICE MODE
↓ MAX VOLUME (SUB-VOL) ↓ SUB CONTRAST (SUB-CON) ↓ SUB COLOUR (SUB-COL) ↓ SUB BRIGHTNESS (SUB-BRI) ↓ SUB TINT (SUB-TINT) ↓ SUB SHARPNESS (SUB-SHP) ↓ MAX HOTEL VOLUME (HTL-VOL) ↓ HOTEL PROGRAM NO(HTL-PRG) ↓ OSD GRB REFERENCE (RGB) ↓ BLACK LEVEL OFFSET R(CUT-R) ↓ BLACK LEVEL OFFSET B(CUT-B) ↓ CATHODE DRIVE LEVEL(CDL)
SUB ADJ. MODE
FORWARD : CH DOWN KEY REVERSE : CH UP KEY
OFFSET ADJ. MODE
Y-DELAY ADJ. MODE
SUB ADJ. MODE
14D1-S/G/W 14D2-S/G
4
↓ NUMBER OF EXT AV SOURCE (AV) ↓ FM WINDOW SELECTION (FMWS) ↓ SOUND MUTE BIT 0 (SM0) ↓ SOUND MUTE BIT 1 (SM1) ↓ THAI LANGUAGE (THA) ↓ ARABIC LANGUAGE (ARA) ↓ MALAY LANGUAGE (MAL) ↓ CHINESE LANGUAGE (CHI) ↓ FRENCH LANGUAGE (FRE) ↓ RUSSIAN LANGUAGE (RUS) ↓ FORCED V-SYNC SLICING LEVEL(FSL) ↓ SYNC OF OSD (HP2) ↓ TUNER SELECTION (CPT) ↓ B
A
4-1
A
↓ SOUND SYSTEM M (S-M) ↓ SOUND SYSTEM DK (S-DK) ↓ SOUND SYSTEM I (S-I) ↓ SOUND SYSTEM BG (S-BG) ↓ PLAYBACK SECAM (P-SECAM) ↓ FE (RF) NTSC 3.58 (F-N358) ↓ FE (RF) NTSC 4.43 (F-N443) ↓ FE (RF) SECAM (F-SECAM) ↓ VIDEO MUTE AT IDENT LOSS (VMI) ↓ VIDEO MUTE AT PROGRAM /SOURCE CHANGE (VMC) ↓ HOTEL MODE (HTL) ↓ REDUCED FM DEMODULATION GAIN FOR BTSC SIGNAL (BTSC) ↓
↓ COLOUR OFFSET (PAL) (COL-OP) ↓ COLOUR OFFSET (SECAM) (COL-OS) ↓ COLOUR OFFSET (NTSC358) (COL-O3) ↓ COLOUR OFFSET (NTSC443) (COL-O4) ↓ SHARPNESS OFFSET (PAL) (SHP-OP) ↓ SHARPNESS OFFSET (SECAM) (SHP-OS) ↓ SHARPNESS OFFSET (NTSC358) (COL-O3) ↓ SHARPNESS OFFSET (NTSC443) (COL-O4)
↓ Y-D TIME FOR PAL (TV) (DL-PT) ↓ Y-D TIME FOR SECAM (TV) (DL-ST) ↓ Y-D TIME FOR N358 (TV) (DL-3T) ↓ Y-D TIME FOR N443 (TV) (DL-4T) ↓ Y-D TIME FOR B/W (TV) (DL-TV) ↓ Y-D TIME FOR PAL (AV) (DL-PA) ↓ Y-D TIME FOR SECAM (AV) (DL-SA) ↓ Y-D TIME FOR N358 (AV) (DL-3A) ↓ Y-D TIME FOR N443(AV) (DL-4A) ↓ Y-D TIME FOR B/W (AV) (DL-AV) *(Y-D : Y-DELAY)
MISC. OPTION MODE
OFFSET ADJ. MODE
Y-DELAY ADJ. MODE
↓ BILINGUAL(BIL) ↓ IF AGC SPEED BIT 0 (AGC0) ↓ IF AGC SPEED BIT 1 (AGC1) ↓ FOA Time Constant-RF (FOA-FE) ↓ FOB Time Constant-RF (FOB-FE) ↓ FOA Time Constant-AV (FOA-AV) ↓ FOB Time Constant-AV (FOB-AV) ↓ LED BLINK SPEED (LED-F) ↓ VOLUME CONTROL TABLE (MSA) ↓ OUTPUT VERTICAL GUARD (NDF)
B
↓ VERTICAL SCAN DISABLE(VSD) ↓ BLACK STRETCH (BKS) ↓ AUTO VOLUME LEVELING(AVL) ↓ FAST FILTER IF-PLL(FFI) ↓ ENABLE VERTICAL GUARD (EVG) ↓ EHT TRACKING MODE (EHT) ↓ OVERSCAN SWITCH OFF(OSO) ↓ AUTO COLOUR LIMIT(ACL) ↓ FORCED COLOUR LIMIT(FCO)
IC OPTION MODE
SUB-SHP
SHARPNESS UP
4-2
SUB-BRI SUB TINT
TINT UP
SUB-COL
BRIGHTNESS UP
COLOUR UP
SUB-VOL SUB-CON
HB S-COR
BLUEBACK TIMER
EW / /
SYSTEM
CONTRAST UP
H-CENT
TINT DOWN SHARPNESS DOWN
V-AMP V-CENT
COLOUR DOWN BRIGHTNESS DOWN
AGC V-LIN
CONTRAST DOWN
SERVICE-ITEM
FUNCTION
RC COMMAND
* Direct Key-in for Service Item in Service Mode
14D1-S/G/W 14D2-S/G
: Data : 55H : 4FH
EEPROM ITEMS AGC TAKE OVER POINT VERTICAL SLOPE VERTICAL AMPLITUDE VERTICAL SHIFT HORIZONTAL SHIFT EAST-WEST WIDTH HORIZONTAL PARALLELOGRAM EAST-WEST PARABOLA/WIDTH EAST-WEST UPPER CORNER PARABOLA EAST-WEST LOWER CORNER PARABOLA EAST-WEST TRAPEZIUM HORIZONTAL BOW S-CORRECTION WHITE POINT RED STD WHITE TEMP WHITE POINT GREEN STD WHITE TEMP WHITE POINT BLUE STD WHITE TEMP WHITE POINT RED COOL WHITE TEMP WHITE POINT GREEN COOL WHITE TEMP WHITE POINT BLUE COOL WHITE TEMP WHITE POINT RED WARM WHITE TEMP WHITE POINT GREEN WARM WHITE TEMP WHITE POINT BLUE WARM WHITE TEMP MAX VOLUME SUB CONTRAST SUB COLOUR SUB BRIGHTNESS SUB TINT SUB SHARPNESS MAX HOTEL VOLUME HOTEL PROGRAM NUMBER OSD GRB REFERENCE BLACK LEVEL OFF-SET R BLACK LEVEL OFF-SET G CATHODE DRIVE LEVEL Y-DELAY TIME FOR PAL(TV) [YD] Y-DELAY TIME FOR SECAM(TV) [YD] Y-DELAY TIME FOR N358 (TV) [YD] Y-DELAY TIME FOR N443 (TV) [YD] Y-DELAY TIME FOR B/W (TV) [YD] Y-DELAY TIME FOR PAL (AV) [YD] Y-DELAY TIME FOR SECAM (AV) [YD] Y-DELAY TIME FOR N358 (AV) [YD] Y-DELAY TIME FOR N443 (AV) [YD] Y-DELAY TIME FOR B/W (AV) [YD] COLOUR OFFSET (PAL) COLOUR OFFSET (SECAM) COLOUR OFFSET (NTSC358) COLOUR OFFSET (NTSC443) SHARPNESS OFFSET (PAL) SHARPNESS OFFSET (SECAM) SHARPNESS OFFSET (NTSC358)
Address 00H 01H
: Data : 43H : A1H
5 5-1
OSD DATA LENGTH INITIAL DATA AGC 0~63 14 V-LIN 0~63 32 V-AMP 0~63 32 V-CENT 0~63 32 H-CENT 0~63 32 H-SIZE 0~63 32 EW// 0~63 32 PARA 0~63 32 COR (U) 0~63 32 COR (L) 0~63 32 TRAPE 0~63 32 HB 0~63 32 S-COR 0~63 0 (17) DRI-RS 0~63 32 DRI-GS 0~63 32 DRI-BS 0~63 32 DRI-RC 0~63 25 DRI-GC 0~63 32 DRI-BC 0~63 32 DRI-RW 0~63 32 DRI-GW 0~63 32 DRI-BW 0~63 32 SUB-VOL 0~63 63 SUB-CON 0~63 63 (52) SUB-COL 0~63 32 SUB-BRI 0~63 32 SUB-TINT 0~63 32 SUB-SHP 0~63 32 (20) HTL-VOL 0~63 32 HTL-PRG 0~99 OR>99FOR NONE 255 RGB 0~15 15 (6) CUT-R 0~63 32 CUT-G 0~63 32 CDL 0~15 0 (5) DL-PT 0~15 12 DL-ST 0~15 15 DL-3T 0~15 12 DL-4T 0~15 12 DL-TV 0~15 12 DL-PA 0~15 12 DL-SA 0~15 15 DL-3A 0~15 12 DL-4A 0~15 12 DL-AV 0~15 12 COL-OP 0~15 8 COL-OS 0~15 8 COL-O3 0~15 4 COL-O4 0~15 4 SHP-OP 0~15 8 SHP-OS 0~15 4 SHP-O3 0~15 12 (8)
Address 02H 03H FIX/ADJ ADJ ADJ ADJ ADJ ADJ *FIX *FIX *FIX *FIX *FIX *FIX *FIX *FIX *FIX ADJ ADJ ADJ ADJ ADJ *FIX ADJ ADJ *FIX *FIX ADJ ADJ ADJ *FIX *FIX *FIX *FIX ADJ ADJ *FIX *FIX *FIX *FIX *FIX *FIX *FIX *FIX *FIX *FIX *FIX ADJ ADJ ADJ ADJ *FIX *FIX *FIX *6 *6 *6 *6
(DRI-GS)-7 DATA (DRI-BS)-7 DATA
*3 (DRI-GS)-7 DATA*3 SAME AS (DRI-BS) DATA
REMARK
AFTER SHORT JA 137 & JA 138 ,AND TURN ON THE MAIN POWER SWITCH,READ DATA FROM EEPROM ADDRESS 00H ~ 03H,AND COMPARE TO THE LIST BELOW, IF DIFFERENT, INITIALIZE THE EEPROM.
NOTE :
5-2
1) *FIX: PLEASE DO NOT CHANGE FIXED DATA WITHOUT SPECIFIC INSTRUCTION. Please set the EEPROM initial data according to the value in parenthesis ( ) before adjustment. 2) *3: 12300˚K DEGREE COLOUR TEMP MINUS 7, DRI-RC=25, DRI-GC=(DRI-GS)-7 18000˚K DEGREE COLOUR TEMP MINUS 5, DRI-RC=27, DRI-GC=(DRI-GS)-5 3) *6: ADJUST COLOUR OFFSET AFTER ADJUST SUB-COLOUR. COLOUR OFFSET (PAL) COL-OP : 8 ------> 14 COLOUR OFFSET (SECAM) COL-OS : 8 ------> 14 COLOUR OFFSET (NTSC358) COL-O3 : 4 ------> 10 COLOUR OFFSET (NTSC443) COL-O4 : 4 ------> 10
EEPROM ITEMS OSD DATA LENGTH INITIAL DATA SHARPNESS OFFSET (NTSC443) SHP-O4 0~15 8 VERTICAL SCAN DISABLE VSD 0(DISABLE)/1(ENABLE) 0 BLACK STRETCH BKS 0(DISABLE)/1(ENABLE) 1 AUTOMATIC VOLUME LEVELING AVL 0(DISABLE)/1(ENABLE) 1 FAST FILTER IF-PLL FFI 0(DISABLE)/1(ENABLE) 0 ENABLE VERTICAL GUARD (RGB BLANKING) EVG 0(DISABLE)/1(ENABLE) 1 EHT TRACKING MODE (HCO) EHT 0(DISABLE)/1(ENABLE) 1 OVERSCAN SWITCH OFF OSO 0(DISABLE)/1(ENABLE) 0 AUTO COLOUR LIMIT ACL 0(DISABLE)/1(ENABLE) 0 FORCED COLOUR LIMIT FCO 0(DISABLE)/1(ENABLE) 0 SOUND SYSTEM M S-M 0(DISABLE)/1(ENABLE) 0 SOUND SYSTEM DK S-DK 0(DISABLE)/1(ENABLE) 1 SOUND SYSTEM I S-I 0(DISABLE)/1(ENABLE) 1 SOUND SYSTEM BG S-BG 0(DISABLE)/1(ENABLE) 1 PLAYBACK SECAM P-SECAM 0(DISABLE)/1(ENABLE) 1 FE (RF) NTSC 3.58 F-N358 0(DISABLE)/1(ENABLE) 0 FE (RF) NTSC 4.43 F-N443 0(DISABLE)/1(ENABLE) 1 FE (RF) SECAM F-SECAM 0(DISABLE)/1(ENABLE) 1 VIDEO MUTE AT IDENT LOSS VMI 0(DISABLE)/1(ENABLE) 1 VIDEO MUTE AT PROGRAM/SOURCE CHANGE VMC 0(DISABLE)/1(ENABLE) 1 HOTEL MODE HTL 0(DISABLE)/1(ENABLE) 0 REDUCED FM DEMODULATOR GAIN FOR BTSC SIGNAL BTSC 0(DISABLE)/1(ENABLE) 0 NUMBER OF EXTERNAL AV SOURCE AV 0 FOR1 AV/1 FOR 2AV 1 (0) FM WINDOW SELECTION FMWS 0(DISABLE)/1(ENABLE) 0 SOUND MUTE BIT 0 SM0 0(DISABLE)/1(ENABLE) 1 SOUND MUTE BIT 1 SM1 0(DISABLE)/1(ENABLE) 0 THAI LANGUAGE THA 0(DISABLE)/1(ENABLE) 0 ARABIC LANGUAGE ARA 0(DISABLE)/1(ENABLE) 1 MALAY LANGUAGE MAL 0(DISABLE)/1(ENABLE) 1 CHINESE LANGUAGE CHI 0(DISABLE)/1(ENABLE) 1 FRENCH LANGUAGE FRE 0(DISABLE)/1(ENABLE) 1 RUSSIAN LANGUAGE RUS 0(DISABLE)/1(ENABLE) 1 FORCED V-SYNC SLICING LEVEL FSL 0(DISABLE)/1(ENABLE) 0 SYNC OF OSD HP2 0(DISABLE)/1(ENABLE) 0 TUNER SELECTION (0:SHARP/ALPS;1:MURATA) CPT 0(DISABLE)/1(ENABLE) 0 BILINGUAL BIL 0(DISABLE)/1(ENABLE) 0 IF AGC SPEED BIT 0 AGC0 0(DISABLE)/1(ENABLE) 1 IF AGC SPEED BIT 1 AGC1 0(DISABLE)/1(ENABLE) 0 PHI-1 TIME CONSTANT (RF) FOA-FE 0(DISABLE)/1(ENABLE) 0 PHI-1 TIME CONSTANT (RF) FOB-FE 0(DISABLE)/1(ENABLE) 0 PHI-1 TIME CONSTANT (OFF AIR) FOA-AV 0(DISABLE)/1(ENABLE) 1 PHI-1 TIME CONSTANT (OFF AIR) FOB-AV 0(DISABLE)/1(ENABLE) 1 LED BLINK SPEED LED_F 0(DISABLE)/1(ENABLE) 0 (1) VOLUME CONTROL PWM TABLE MSA 0(DISABLE)/1(ENABLE) 0 (1) OUTPUT VERTICAL GUARD NDF 0(DISABLE)/1(ENABLE) 0 (1) FIX/ADJ *FIX *FIX *FIX *FIX *FIX *FIX *FIX *FIX *FIX *FIX *FIX *FIX *FIX *FIX *FIX *FIX *FIX *FIX *FIX *FIX *FIX *FIX *FIX *FIX *FIX *FIX *FIX *FIX *FIX *FIX *FIX *FIX *FIX *FIX *FIX *FIX *FIX *FIX *FIX *FIX *FIX *FIX *FIX *FIX *FIX
REMARK
14D1-S/G/W 14D2-S/G
INITIAL SETTING
6
99
"
CH-NO 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46
41.10
MCL1 Fv (MHz) 41.10 48.25 62.25 77.25 175.25 182.25 183.25 191.25 196.25 199.25 210.25 224.25 471.25 487.25 503.25 575.25 583.25 599.25 621.25 639.25 703.25 735.25 767.25 815.25 855.25 855.25 55.25 83.25 183.25 193.25 217.25 471.25 477.25 693.25 41.10 112.25 168.25 41.10 294.25 463.25 41.10 647.25 663.25 679.25 174.95 175.55 41.10
B/G B/G B/G B/G B/G
B/G B/G
B/G B/G
B/G B/G D/K B/G B/G D/K D/K B/G M B/G B/G B/G I B/G B/G B/G B/G M D/K B/G I B/G B/G I B/G M M M M M M M M
SOUND SYS
6-1
(1). In service mode, After execute select POS 1, store the following tuning data in E2PROM. Note: All sound system of following channels will be set to B/G or I after pressing INITIAL KEY 2, 3 or 4.
SHIPPING SETTING & CHECKING DATA SETTING 1 1 1 AUTO *1 OFF ON 1 60 (MAX) 0 (CENTER) 0 (CENTER) 0 (CENTER) 0 (CENTER) STANDARD In-active, "--:--" In-active, "--:--" In-active, "--:--" POWER-ON *1 ON OFF ON TV
LANGAUGE CHINESE ENGLISH ARABIC
Geomagnetism (H,V) nT "30,000" "20,000" "-10,000" "40,000" "30,000" "20,000" "-10,000" "40,000"
Background 12300K 12300K 12300K 12300K
Lang. CHINESE ENGLISH ARABIC ENGLISH
6-2
LANGUAGE QTY: ENGLISH/CHINESE/FRENCH/ARABIC/MALAY/RUSSIAN
MODEL HONG KONG) (SINGAPORE) (MID EAST) (AFRICA)
S-SYS I B/G B/G B/G
SOUND SYSTEM I B/G B/G
FACTORY SETTINGS BY MODELS (Reference: Geomagnetism Adjustment)
INITIAL 2 3 4
Lang. QTY 6 6 6 6
*1: Please refer defaults for LANGUAGE and SOUND SYSTEM per MODEL as follows,
ITEMS LAST PROGRAM/CHANNEL FLASHBACK PROGARM/CH DIGIT C-SYSTEM S-SYSTEM SKIP AFC VOLUME CONTRAST COLOUR BRIGHTNESS TINT SHARPNESS WHITE TEMP REMINDER TIMER ON TIMER OFF TIMER LAST POWER LANGUAGE BLUE BACK MUTE HOTEL MODE 0 CHANNEL SKIP LAST TV/AV
(1) The following default data has been factory-set for the E2PROM.
14D1-S/G/W 14D2-S/G
Tuner IFT ( PRESET )
RF-AGC TAKE OVER POINT ADJUSTMENT (I2C BUS CONTROL)
1
2
No. Adjusting point
7
–
+
» Bias box: About 4.5 V
TV Set
TP210
7-1
Fig. 3 3. Call "AGC" mode in service mode. Adjust the "AGC" bus data to obtain the Tuner output pin drop 0.1V below maximum voltage. 4. Change the antenna input signal to 63~67dBµV, and make sure there is no noise. 5. Turn up the input signal to 90~95 dBµV to be sure that there is no cross modulation beat.
Bias box
Oscilloscope + 0.1V –
1. Receive "PAL COLOUR BAR" signal. » Signal Strength: 57 ± 1 dBµV (75 ohm open) 2. Connect the oscilloscope to TP201(Tuner’s AGC Terminal) as shown in Fig. 3.
Note: Be sure to keep the tuner cover in position during this adjustment.
1. Get the tuner ready to receive the CH. E - 9 signal,but with no signal input. Adjust the PLL data. 2. Connect the sweep generator's output cable to the tuner antenna. ( RF SWEEP ) 3. Adjust the sweep generator's to 80dBuV. 4. Connect the response lead ( use LOW IMPEDANCE probe with wave detector ; see Fig.1 ) to the tuner's IF output terminal. ( This terminal must have the probe alone connected ). 5. Set the RF AGC to 0 - 6 V with no saturation with the waveform. 6. Adjust the tuner IF coil to obtain the waveform as shown in Fig. 2.
Adjusting procedure/conditions
PIF ADJUSTMENT
P
100k
Fig.2
E-9 CH
Fig.1
1n60 IF OUT
-1.5+/-0.8dB
C
75ohm
1000p
Note: For the 50 ohm signal strength gauge, when not using 50/75 impedance adapter, signal strength is 52±1dBµV(75 ohm open), instead of 57±1dBµV (75 ohm open). Precaution: The loss of using impedance adapter
Oscilloscope
10k
Waveform and others
ADJUSTMENT PRECAUTION: Make sure TV Set is in "Normal Condition" before switch to service mode for adjustment. 1
PURITY ADJ.
No. Adjusting point
Green-only
7-2
Signal-colour screen cleared
Blue-only
Red-only
* For the following colours press R/C RGB key to change.
1. Receive the GREEN-ONLY signal. Adjust the beam current to about 500 µA. 2. Degauss the CRT enough with the degausing coil. Note: Follow the Job Instruction Sheet to adjust the magnetic field. 3. Maintain the purity magnet at the zero magnetic field and keep the static convergence roughly adjusted. 4. Observe the points a, b as shown in Fig. 4-1 through the microscope. Adjust the landing to the rank A requirements. 5. Orient the raster rotation to 0 eastward. 6. Tighten up the deflection coil screws. » Tightening torque: 108 ± 20 N (11 ± 2 kgf) 7. Make sure the CRT corners landing meet the A rank requirements. If not, stick the magnet sheet to correct it. Note: This adjustment must be done after warming up the unit for 30 minutes or longer with a beam current over 500 µA.
Adjusting procedure/conditions
PURITY ADJUSTMENT
B
A
Fig. 4-1
A=B
b
A=B
The TEXT Key "R. G. Cy" Key can be directly use to change to other colours screen.
* Press R/C RGB key for 1 second in NORMAL MODE, the colour will change to RGB mono colour mode.
Rank "A" (on the left of the CRT)
Fig. 4-3
B
A
Fig. 4-2 Rank "A" (on the right of the CRT)
a
Waveform and others
14D1-S/G/W 14D2-S/G
1
CONVERGENC ADJ. ( To be done after the purity adjustment.
No. Adjusting point
8 8-1
Note*** SAMSUNG CRT : 32mm CPT CRT : 35mm TOSHIBA CRT : 35mm
Finally received the Red-only and Blue-only signals to make sure there is no other colours on the screen.
DYNAMIC CONVERGENCE 1. Adjust the convergence on the fringes of the screen in the following steps. a) Fig. 5-1: Drive the wedge at point "a" and swing the deflection coil upward. b) Fig. 5-2: Drive the wedge at points "b" and "c" and swing the deflection coil downward. c) Fig. 5-3: Drive the "c" wedge deeper and swing the deflection coil rightward. d) Fig. 5-4: Drive the "b" wedge deeper and swing the deflection coil leftward. 2. Fix all the wedges on the CRT and apply glass tape over them. 3. Apply lacquer to the deflection yoke lock screw, magnet unit (purity, 4-pole, 6-pole magnets) and magnet unit lock screw.
STATIC CONVERGENCE 1. Turn the 4-pole magnet to a proper opening angle in order to superpose the blue and red colours. 2. Turn the 6-pole magnet to a proper opening angle in order to superpose the green colour over the blue and red colours.
1. Receive the "Crosshatch Pattern" signal. 2. Using the remote controller, call NORMAL mode.
Adjusting procedure/conditions
Wedge "a"
Fig. 5-4
Fig. 5-3 BGR
RGB
Wedge "c"
About 100°
R G B
B G R
Lacquer Purity magnet
Note***
4-pole magnet 6-pole magnet CRT neck
Wedge "b"
Lacquer
About 100°
R G B
B G R
Fig. 5-2
RGB
Fig. 5-1
BGR
Waveform and others
CONVERGENCE ADJUSTMENT
3
2
1
WHITE BALANCE SERVICE MODE ADJ. (I2C BUS CONTROL)
SUB-BRIGHTNESS ADJUSMENT (I2C BUS CONTROL)
CRT CUTOFF ADJUSTMENT (I2C BUS CONTROL)
No. Adjusting point
8-2
* ADJUST DRI-GC/GW, DRI-BC/BW as following DATA, after finishing DRI-BS and DRI-GS DATA ADJUSTMENT. DRI-RW = 32 (FIXED), DRI-RS = 32 (FIXED) DRI-BC = "DRI-BS" (For 12300°K And 18000°K Condition)
Note: This adjustment must be done after warming up the unit for 30 minutes or longer with a beam current over 500µA.
1. Receive the "WHITE" pattern with BURST signal. 2. Press R/C to set Picture NORMAL condition. 3. Connect the DC miliammeter between TP602 (-) TP603 (+). 4. Check Beam current should be around 800 µA. 5. Set it to service mode and adjust the DRI-GS, & DRI-BS data to have a colour temperature of 12300°K or 18000°K ( white ). * Note . 6. Receive "WHITE" pattern, WITH BURST signal, and set BRIGHTNESS Y by generator, to **10 c d / m 2 ( M I N O LTA C A - 1 0 0 ) b y r e d u c i n g LUMINATE Y signal. 7. Adjust "CUT-R" & "CUT-G" to get desired colour temperature #. Then go back NORMAL mode (HIGH BRIGHT**) to check colour temperature. If out of range, back to (1).
1. Call " SUB-BRI" in service mode. (Receive Crosshatch pattern with 5 black level windows) *(2) Adjust the " SUB BRIGHT " bus data in order that the line 1and 2 have the same darkness wherelse line 3 is one step (data) brighter than line 2. Finally data minus 1 to make line 1, 2, and 3 are in same level (darkness).
1. Switch TV to VIDEO mode,BLUE BACK OFF, with NO VIDEO signal. 2. Press R/C to set Picture Normal condition. 3. First, off the screen by adjust screen variable resistor. *4. Next, checking AKB circuit function by slowly increase screen variable resistor until colour raster suddenly on and off (AKB start function). 5. Then continue adjust until retrace line appear. 6. Finally, slowly decrease the screen variable resistor until screen retrace line cut off. (Not Raster) Note : Must confirm the AKB function in set before continue the next adjustment.
Remark 1. Before CRT cutoff adjustment, SUB-BRIGHT, DRI-RS/RW/RC, DRI-GS/GW/GC, DRI-BS/BW/ BC, CUT-R and CUT-G must be INITIAL DATA. 2. CRT Cutoff adjustment must be done inside a dark room.
Adjusting procedure/conditions
1 2 3 4 5
Line 3 is one step (data) brighter than line 2
1 2 3 4 5
t
LOW HIGH 10cd/m2 200cd/m2
* 18000°K DRI-GW="DRI-GS"-7 DRI-BW="DRI-BS"-7 DRI-GC="DRI-GS"-5 DRI-RC=27
* 12300°K DRI-GW="DRI-GS"-7 DRI-BW="DRI-BS"-7 DRI-GC="DRI-GS"-7 DRI-RC=25
14"
(MINOLTA COLOUR ANALYZER CA-100) *Note: Above Data can be UP/ DOWN by Volume key.
# 12300°K X : 0.272 Y : 0.275 # 18000°K X : 0.255 Y : 0.255
2
1
0
3.3Vdc
*Alternative Procedure (1) Step (1), (2), (3) and (4) are same as beside procedure. (2) Then continue adjust until retrace line appear and make sure the colour appear whether red, green or blue. (3) Connect the oscilloscope to related test points as below which is based on colour appear at (2) RED = TP47R, GREEN = TP47G, BLUE = TP47B. (4) Then adjust Screen VR until the tip of signal reach 3.3Vdc.
Waveform and others
CRT CUT-OFF, BACKGROUND AND SUB-CONTRAST ADJUSTMENT
14D1-S/G/W 14D2-S/G
Max beam check
1. Receive the "Monoscope Pattern" signal. 2. Press R/C to set Picture NORMAL condition. 3. Connect the DC miliammeter between TP603 (+) & TP602 (–). (Full Scale: 3 mA Range) 4. Beam current must be within 800 ± 100 µA.(14")
Adjusting procedure/conditions
Waveform and others
9
1. Call the "H-CENT" mode. 2. Increase or decrease "H-CENT" by Volume key to center the picture horizontal.
1. SET DATA TO 17. * Check the E-5 CH Monoscope Pattern then readjust V-Slope, V-Shift and V-Amp to makesure adjustment is in acceptable Ring-Shaped.
H-SHIFT (50) (H-CENTER)
S-CORRECTION (I2C BUS CONTROL)
SUB-SHARPNESS
Focus
4
5
6
1
1
SUB COLOUR (I2C BUS CONTROL)
No. Adjusting point
1. Call the "V-AMP" mode. 2. Increase or decrease "V-AMP" by Volume key to set overscan of 9.5% typical. Adjustment Spec 9.5% range +1% -0%.
V-AMP50 (I2C BUS CONTROL)
3
Waveform and others
9-1
1. Receive the "PAL Colour Bar" signal. 2. Press R/C to set Picture Normal condition. 3. Connect the oscilloscope to Red cathode(D881 Cathode). » Range : 20 V/div. (AC) (Using 10:1 probe) » Sweep time : 10 µsec/div. 4. Using the R/C call "SUB COL" in SERVICE mode. Adjust SUB COLOUR bus data, so that the 75% White & Red portions of PAL Color Bar be at the same level shown as Fig. 1-1. 5. Clear the SERVICE mode.
Adjusting procedure/conditions
Fig. 1-1
W Y 100%W Mg R 75%
Cy G
B
Waveform and others
PAL CHROMA ADJUSTMENT
1. Receive the "Monoscope Pattern" signal. 2. Press R/C to set Picture NORMAL condition. 3. Adjust the focus control to get the best focusing.
1. SET DATA TO 20.
1. Call the "V-CENT" mode. 2. Increase or decrease "V-CENT" by Volume key till the picture is centered.
V-SHIFT-50 (I2C BUS CONTROL)
2
1. Receive Monoscope Pattern Signal. 2. Call the "V-LIN" mode. 3. Increase or decrease "V-LIN" by Volume key till the horizontal line in the center of monoscope is just at the position where the blanking starts.
V-SLOPE (I2C BUS CONTROL)
Adjusting procedure/conditions
1
No. Adjusting point
HORIZONTAL AND VERTICAL DEFLECTION LOOP ADJUSTMENT
4
No. Adjusting point
(Continued)
CRT CUT-OFF, BACKGROUND AND SUB-CONTRAST ADJUSTMENT
Adjusting procedure/conditions
2
VIDEO AND AUDIO INPUT CHECK
9-2
1. Using the TV/AV key on the remote controller, make sure that the modes change in order of TV, AV & TV again and the video & audio output are according to the input terminal for each mode.If connect input to Front and Rear AV terminal, input terminal of Front AV will be selected.
Adjusting procedure/conditions 1. Receive the "PAL Color Bar" signal (100% White Color Bar, Sound 400 Hz 100% Mod). 2. Terminate the Video output with a 75 ohm impedance. Make sure the output is as specified (1.0 Vp-p ±3 dB). 3. Terminate the Audio output with a 10k ohm impedance. Make sure the O/P is as specified (1.76 Vp-p ±3 dB). 1
W Y Cy G Mg R B Fig. 1-1
SAME LEVEL
Waveform and others
Waveform and others * Select one of Q883/5/7 to do each short test.
Waveform and others
A/V INPUT AND OUTPUT CHECKING
1. Once finish rectified Electrolytic Capacitor short testing in +B line, check all possible damaged components on +B line. (Use random selected set for inspection)
1. Receive "Monoscope Pattern" signal. 2. Connect output of Bias Box to D603 cathode (R610 side). 3. Set voltage of Bias Box to 18V and make sure the protector is not work. 4. Set voltage of Bias Box to 27V, and make sure the protector is work.
1. Receive "Monoscope Pattern" signal. 2. Set CONTRAST MAX. 3. Set BRIGHT MAX. 4. During the Collector & Emitter of Q883/5/7 short, make sure the protector ON and switch to standby mode.
VIDEO AND AUDIO OUTPUT CHECK
Other protectors
H•V PROTECTOR
BEAM PROTECTOR
No. Adjusting point
3
2
1
1. Receive the "NTSC 3.58 Colour Bar" signal thru AV in. 2. Connect the oscilloscope to TP47B (P882 pin 5) BLUE-OUT. » Range : 100mV/div. (AC)(Use Probe 10:1) » Sweep time : 10 µsec/div. 3. Call the "SUB-TINT" mode in service mode. Adjust the "SUB-TINT" bus data to obtain the waveform shown as Fig. 1-1. 4. Clear the SERVICE mode.
Adjusting procedure/conditions
NTSC CHROMA ADJUSTMENT
PROTECTOR OPERATION CHECKING
SUB-TINT (I2C BUS CONTROL)
No. Adjusting point
1
No. Adjusting point
14D1-S/G/W 14D2-S/G
10
WHITE TEMP
8
SHARPNESS Key
5
NORMAL Key
TINT key
4
7
BRIGHTNESS key
3
CH DISPLAY COLOUR
COLOUR key
2
6
CONTRAST key
1
No. Adjusting point
CONTRAST COLOUR BRIGHTNESS TINT SHARPNESS
: MAX : CENTER : CENTER : CENTER : CENTER
10-1
1. Receive "Monoscope Pattern" signal. 2. Set FUNCTION to select WHITE TEMP. 3. Press Volume Up/Down key to check WHITE TEMP Option, STANDARD: NORMAL SETTING, WARM for more REDDISH direction changing, COOL for more BLUISH direction changing.
» » » » »
1. Once in PICTURE Mode, and theNORMAL key is pressed, all the settings will be present to normal setting. (Normal setting value for every mode).
1. All Ch (1~99) will have an OSD display of the channel number in green colour under AFT ON condition.
1. Receive "Monoscope Pattern" signal. 2. Set P-mode to select SHARPNESS. 3. Press Volume Up/Down key to check whether the SHARPNESS effect is OK or not.
1. Receive the "NTSC Colour Bar" signal thru AV in. 2. Set P-Mode to select TINT. 3. Press Volume Up/Down key to check TINT, UP for GREEN direction and DOWN for PURPLE direction whether is OK or not.
1. Receive "Monoscope Pattern" signal. 2. Set P-Mode to select BRIGHTNESS. 3. Press Volume Up/Down key to check whether the BRIGHTNESS effect is OK or not.
1. Receive "Color Bar" signal. 2. Set P-Mode to select COLOUR. 3. Press Volume Up/Down key to check whether the COLOUR effect is OK or not.
1. Receive "Monoscope Pattern" signal. 2. Set P-Mode to select CONTRAST. 3. Press Volume Up/Down key to check whether the CONTRAST effect is OK or not.
Adjusting procedure/conditions
Notes:If nothing is display mean contrast, colour, bright, tint, sharpness are all in normal setting.
Waveform and others
FUNCTION OPERATION CHECKING (VIDEO AND AUDIO)
12
11
10
9
OSD LANGUAGE QUANTITY CHECK
NOISE MUTE CHECKING
SOUND SYSTEM
COLOUR SYSTEM
No. Adjusting point
10-2
Check OSD LANGUAGE quantity and type as English, Russian, Chinese, French, Arabic and Malay.
1. Receive "PAL COLOUR BAR" signal. 2. Turn up the volume control to maximum, make sure the sound is heard from the speakers. Then put the unit in no signal state. 3. Check the sound mute is effective. 4. Finally turn sound level of CTV to minimum.
1. Receive "PAL-D/K" signal, press the "SOUND SYSTEM" to select B/G, I. Check the sound output is not working properly. Select D/K and check the sound output to make sure it is working properly. 2. Receive "PAL-I" signal, press the "SOUND SYSTEM" to select B/G, D/K. Check the sound output is not working properly. Select I and check the sound output to make sure it is working properly. 3. Receive "PAL-B/G" signal, press the "SOUND SYSTEM"to select I, D/K. Check the sound output is not working properly. Select B/G and check the sound output to make sure it is working properly.
1. Receive the "PAL COLOUR BAR" signal, press the COLOUR SYSTEM key to select modes except PAL, check the COLOUR is not working properly. Then, select the "PAL" mode. Check again its colour so that it is working properly. 2. Receive "SECAM COLOUR BAR" signal, press COLOUR SYSTEM key to select modes except SECAM, check the COLOUR is not working properly. Then, select the "SECAM" mode. Check again its colour so that it is working properly. 3. Receive "NTSC 4.43/3.58 COLOUR BAR" signal thru AV, press COLOUR SYSTEM key to select modes except N4.43/3.58, check the COLOUR is not working properly. Then, select the "NTSC 4.43/3.58" mode. Check again its colour so that it is working properly.
Adjusting procedure/conditions
(Continued) Waveform and others
FUNCTION OPERATION CHECKING (VIDEO AND AUDIO)
14D1-S/G/W 14D2-S/G
PASS WORD
MICON
EW-TRAPEZIUM
HORIZONTAL-BOW
S-CORRECTION
11
12
(1) 20th August 2001:Change of range & default.
FAV-POS B FAV-POS C
57 58
WHITE-TEMP BLUE BACK
5E
LAST POWER MODE
5D
5C
5B
5A
FAV-POS D
FAV-POS A
59
POSITION/AV1/AV2
55
SUB-COLOUR
24
25
11
SKIP 8
SKIP 9
SKIP 72
6A 6B
2B
2C
00-0F
LETTER NO.
00-0F
00-0F
08
LETTER NO.
3F
00-0F
04 04
08
MODEL
SHARPNESS-OFFSET (PAL)
3E
MODEL
COLOUR-OFFSET (N358)
COLOUR-OFFSET (N443)
3D
COLOUR-OFFSET (SECAM)
00-0F
3C
00-0F 00-0F
0C 08
0C
Y-DELAY (AV BW)
Y-DELAY (AV N443)
COLOUR-OFFSET (PAL)
3B
39
3A
00-0F
0C
Y-DELAY (AV N358)
38
00-0F
00-0F
0C 0F
Y-DELAY (AV SECAM)
37
00-0F 00-0F
36
00-0F
00-0F
0F 0C
00-0F
0C
00-0F
00-3F
20 0C
00-3F
20 00
00-0F
0F
0C
Y-DELAY (TV BW)
Y-DELAY (AV PAL)
35
Y-DELAY (TV N358)
Y-DELAY (TV N443)
Y-DELAY (TV SECAM)
32
33
Y-DELAY (TV PAL)
34
CATHODE DRIVE LEVEL
CUTOFF LEVEL -OFFSET G
2F
30
31
CUTOFF LEVEL -OFFSET R
OSD-REFERENCE
2E
2D
SKIP 99
SKIP 91
SKIP 44
SKIP 45 SKIP 53
SKIP 92
SKIP 84
SKIP 76
SKIP 68
SKIP 93
SKIP 85
SKIP 77
SKIP 69
SKIP 60 SKIP 61
SKIP 52
SKIP 37
LETTER NO.
(auto)
TUNING FREQUANCY (LOWER PART) AFT
TUNING FREQUANCY (HIGHER PART)
7F
S-SYS
(auto)
7D
AFT
7E
7C
TUNING FREQUANCY (LOWER PART)
(auto) TUNING FREQUANCY (HIGHER PART)
AFT
TUNING FREQUANCY (LOWER PART)
TUNING FREQUANCY (HIGHER PART)
(auto)
7B S-SYS
S-SYS
AFT
7A
79
78
77
76
TUNING FREQUANCY (LOWER PART)
SKIP 98
SKIP 90
SKIP 83
SKIP 75
SKIP 67
SKIP 59
SKIP 51
SKIP 43
SKIP 35 SKIP 36
SKIP 29
SKIP 21
SKIP 13
TUNING FREQUANCY (HIGHER PART) S-SYS
SKIP 97
SKIP 89
SKIP 82
SKIP 74
SKIP 20
SKIP 12
SKIP 4
SKIP 27 SKIP 28
SKIP 19
SKIP 11
SKIP 3
74
MODEL
SKIP 96
SKIP 88
SKIP 81
SKIP 73
SKIP 66
SKIP 58
SKIP 50
SKIP 42
SKIP 34
SKIP 26
SKIP 18
SKIP 10
SKIP 2
75
73
72
71
70
6F
6E
6D
SKIP 80
SKIP 65
SKIP 64
6C
SKIP 57
00-FF
FF
SKIP 56
HTL-POSITION
SKIP 41
69
29
2A
00-3F
20
SKIP 49
HTL-VOLUME
28
SKIP 48
SUB-SHARPNESS
27
SKIP 40
SKIP 33
SKIP 25
SKIP 17
68
SKIP 24
SKIP 16
67
00-3F
20
65
64
63
62
SKIP 32
00-3F
20
00-3F 00-3F 00-3F
3F 20 20
00-3F
3F
66
SUB-TINT
SUB-CONTRAST
SUB-BRIGHTNESS
23
26
SUB-VOLUME
22
SKIP 5
SHARPNESS
TINT
BRIGHTNESS
56
54
53
52
51
50
4F
61
1F
NDF
AGC0
MLY
HTL
I
VOLUME
AGC1
CHN
BTSC
BG
FFI
COLOUR
FOA-FE
FRA
AV
PB-SECAM
EVG
CONTRAST
FOB-FE
RUS
FMWS
N358
EHT
4C
SKIP 1
FOA-AV
FSL
SM0
N443
OSO
4E
SKIP 0
FOB-AV
HP2
SM1
SECAM
ACL
SKIP 94
SKIP 86
SKIP 78
SKIP 70
SKIP 62
SKIP 54
SKIP 46
SKIP 38
SKIP 30
SKIP 22
SKIP 14
SKIP 6
MSA
BIL
ARB
VMC
DK
AVL
CPT
THA
VMI
M
BKS
D0
C-SYS
C-SYS
C-SYS
C-SYS
SKIP 95
SKIP 87
SKIP 79
SKIP 71
SKIP 63
SKIP 55
SKIP 47
SKIP 39
SKIP 31
SKIP 23
SKIP 15
SKIP 7
LED-F
SHARPNESS-OFFSET (N443)
4D
4B
4A
49
48
47
46
45
44
43 FCO
D1
SHARPNESS-OFFSET (N358)
D2
41 42
21
00-3F
20
REMARK
LANGUAGE
00-3F
20
LAST INITIAL SETTING DATA
LAST DIGIT MODE (1 OR 2)
DRIVE-B (COOL)
1E
CHECK TYPE
CTV FINAL CHECK DATA
DATA D4 D3
60
DRIVE-G (COOL)
1D
00-3F 00-3F
00-3F
19
20
00-3F
20 20
00-3F
20
CHECK TYPE
CHASSIS CHECK DATA
D5
5F
DRIVE-R (COOL)
00-3F
00-3F
20
20
00-3F
00
00-3F
20 00-3F
00-3F
20 20
00-3F
20
EEPROM WRITE(CPU)
D6 SHARPNESS-OFFSET (SECAM)
D7
40
(HEX)
ADDRESS
20
DRIVE-G (WARM)
DRIVE-B (WARM)
1C
DRIVE-R (WARM)
18
19
1B
DRIVE-B (STANDARD)
17
1A
DRIVE-R (STANDARD)
DRIVE-G (STANDARD)
16
15
14
13
EW-UPPER CORNER
EW-LOWER CORNER
0E
0F
EW-PARABOLA/WIDTH
0D
10
EW-PARALLELOGRAM
0C 00-3F
00-3F
20
H-SIZE
20
00-3F
20
H-CENTER
0B 00-3F
00-3F
20
V-CENTER
09
0A 20
00-3F
08
20
V-SLOPE
07
V-AMPLITUDE
AGC TAKE-OVER
06 00-3F
00-FF
00-FF 00-FF
4F 43 A1
00-FF
RANGE
EEPROM
55
DEFAULT
11-1
D0
20
D1
00-3F
D2
0E
05
04
03
D3
PASS WORD
DATA
PASS WORD
D4
01
D5
02
D6
PASS WORD
D7
00
(HEX)
ADDRESS
MEMORY MAP MICON
1B
00-3C
00-FF
00-07 00-01
00
00-FF 00-FF 00-FF
EEPROM
1:ON
0:OFF
AFT
011:M
010:DK
001:I
000:BG
S-SYS
WRITE(CPU)
LETTER NO.
MODEL
00-FF
00-FF
11-2
00
00
00-FF
00 00
00
00-FF
00-FF 00 00
00-FF 00
00-FF
00-FF
00-FF
00
00
00
00
00-FF
00-01 00
80
00-02 00
00-01 00
00
00-FF
14 1E 28
00-FF 00-FF
0A
00-FF
00-3C
00-3C
01
1E
1E
00-3C
00-3C
1E
00-3C
01 1E
00-03
00-FF
00-FF
00-FF
00-FF
00-FF
3C
00
C4
3E
53
DE
00-0F
00-0F
0C 08
00-0F
RANGE
EEPROM
04
DEFAULT CHECK TYPE
CHASSIS CHECK DATA
CHECK TYPE
CTV FINAL CHECK DATA
LAST INITIAL SETTING DATA
POS 3
POS 2
POS 1
POS 0
(1) 20th August 2001: Added 3 new items.
REMARK
14D1-S/G/W 14D2-S/G
DATA
D3
D2
12
BF
BE
AFT
(auto)
MICON DEFAULT
EEPROM WRITE(CPU)
LETTER NO.
RANGE
EEPROM
LETTER NO.
12-1
C-SYS
C-SYS
C-SYS
C-SYS
C-SYS
C-SYS
C-SYS
C-SYS
C-SYS
C-SYS
C-SYS
C-SYS
C-SYS
C-SYS
C-SYS
C-SYS
C-SYS
C-SYS
C-SYS
C-SYS
C-SYS
D0
MODEL
TUNING FREQUANCY (HIGHER PART)
D1
MODEL
S-SYS
(auto)
TUNING FREQUANCY (LOWER PART)
BD
AFT
TUNING FREQUANCY (HIGHER PART)
BC
BB
S-SYS
(auto)
TUNING FREQUANCY (LOWER PART)
AFT
TUNING FREQUANCY (HIGHER PART)
B9
B8
BA
S-SYS
(auto)
TUNING FREQUANCY (LOWER PART)
B7
AFT
TUNING FREQUANCY (HIGHER PART)
B6
B5
S-SYS
(auto)
TUNING FREQUANCY (LOWER PART)
AFT
TUNING FREQUANCY (HIGHER PART)
B3
B2
B4
S-SYS
(auto)
B1
AFT
TUNING FREQUANCY (HIGHER PART)
TUNING FREQUANCY (LOWER PART)
B0
AF
S-SYS
(auto)
TUNING FREQUANCY (LOWER PART)
AFT
TUNING FREQUANCY (HIGHER PART)
AE
AC
AD
S-SYS
(auto)
TUNING FREQUANCY (LOWER PART)
AFT
TUNING FREQUANCY (HIGHER PART)
AB
A9
AA
S-SYS
(auto)
TUNING FREQUANCY (LOWER PART)
A8
AFT
TUNING FREQUANCY (HIGHER PART)
A7
A6
S-SYS
(auto)
TUNING FREQUANCY (LOWER PART)
A5
AFT
TUNING FREQUANCY (HIGHER PART)
A4
A3
S-SYS
(auto)
TUNING FREQUANCY (LOWER PART)
AFT
TUNING FREQUANCY (HIGHER PART)
A2
A0
A1
S-SYS
(auto)
TUNING FREQUANCY (LOWER PART)
9F
AFT
TUNING FREQUANCY (HIGHER PART)
9E
9D
S-SYS
(auto)
TUNING FREQUANCY (LOWER PART)
9C
AFT
TUNING FREQUANCY (HIGHER PART)
9B
9A
S-SYS
(auto)
TUNING FREQUANCY (LOWER PART)
99
AFT
TUNING FREQUANCY (HIGHER PART)
98
97
S-SYS
(auto)
TUNING FREQUANCY (LOWER PART)
96
AFT
TUNING FREQUANCY (HIGHER PART)
95
94
S-SYS
(auto)
TUNING FREQUANCY (LOWER PART)
AFT
TUNING FREQUANCY (HIGHER PART)
93
91
92
S-SYS
(auto)
TUNING FREQUANCY (LOWER PART)
AFT
TUNING FREQUANCY (HIGHER PART)
8E
8F
90
S-SYS
(auto)
TUNING FREQUANCY (LOWER PART)
AFT
TUNING FREQUANCY (HIGHER PART)
8C
8B
8D
S-SYS
(auto)
TUNING FREQUANCY (LOWER PART)
AFT
TUNING FREQUANCY (HIGHER PART)
89
88
8A
S-SYS
(auto)
TUNING FREQUANCY (LOWER PART)
AFT
TUNING FREQUANCY (HIGHER PART)
86
85
87
S-SYS
(auto)
84
AFT
TUNING FREQUANCY (HIGHER PART)
TUNING FREQUANCY (LOWER PART)
83
82
S-SYS
D4
TUNING FREQUANCY (LOWER PART)
D5
81
D6
TUNING FREQUANCY (HIGHER PART)
D7
80
(HEX)
ADDRESS CHECK TYPE
CHASSIS CHECK DATA
CHECK TYPE
CTV FINAL CHECK DATA
LAST INITIAL SETTING DATA REMARK
POS 25
POS 24
POS 23
POS 22
POS 21
POS 20
POS 19
POS 18
POS 17
POS 16
POS 15
POS 14
POS 13
POS 12
POS 11
POS 10
POS 9
POS 8
POS 7
POS 6
POS 5
POS 4
D4
DATA D3
D2
(auto)
(auto)
(auto)
(auto)
(auto)
(auto)
(auto)
(auto)
(auto)
(auto)
(auto)
(auto)
(auto)
(auto)
(auto)
AFT
(auto)
TUNING FREQUANCY (LOWER PART)
TUNING FREQUANCY (HIGHER PART)
AFT
TUNING FREQUANCY (LOWER PART)
TUNING FREQUANCY (HIGHER PART)
AFT
TUNING FREQUANCY (LOWER PART)
TUNING FREQUANCY (HIGHER PART)
AFT
TUNING FREQUANCY (LOWER PART)
TUNING FREQUANCY (HIGHER PART)
AFT
TUNING FREQUANCY (LOWER PART)
TUNING FREQUANCY (HIGHER PART)
AFT
TUNING FREQUANCY (LOWER PART)
TUNING FREQUANCY (HIGHER PART)
AFT
TUNING FREQUANCY (LOWER PART)
TUNING FREQUANCY (HIGHER PART)
AFT
TUNING FREQUANCY (LOWER PART)
TUNING FREQUANCY (HIGHER PART)
AFT
TUNING FREQUANCY (LOWER PART)
TUNING FREQUANCY (HIGHER PART)
AFT
TUNING FREQUANCY (LOWER PART)
TUNING FREQUANCY (HIGHER PART)
AFT
TUNING FREQUANCY (LOWER PART)
TUNING FREQUANCY (HIGHER PART)
AFT
TUNING FREQUANCY (LOWER PART)
TUNING FREQUANCY (HIGHER PART)
AFT
TUNING FREQUANCY (LOWER PART)
TUNING FREQUANCY (HIGHER PART)
AFT
TUNING FREQUANCY (LOWER PART)
TUNING FREQUANCY (HIGHER PART)
AFT
TUNING FREQUANCY (LOWER PART)
TUNING FREQUANCY (HIGHER PART)
AFT
TUNING FREQUANCY (LOWER PART)
MICON RANGE
EEPROM
EEPROM WRITE(CPU)
LETTER NO.
12-2
DEFAULT
LETTER NO.
TUNING FREQUANCY (LOWER PART)
C-SYS
C-SYS
C-SYS
C-SYS
C-SYS
C-SYS
C-SYS
C-SYS
C-SYS
C-SYS
C-SYS
C-SYS
C-SYS
C-SYS
C-SYS
C-SYS
C-SYS
C-SYS
C-SYS
C-SYS
C-SYS
D0
MODEL
TUNING FREQUANCY (HIGHER PART)
D1
MODEL
FF
(auto)
FE
AFT
TUNING FREQUANCY (LOWER PART) S-SYS
TUNING FREQUANCY (HIGHER PART)
FD
FB
(auto)
FC
AFT
TUNING FREQUANCY (LOWER PART) S-SYS
TUNING FREQUANCY (HIGHER PART)
FA
F9
(auto)
F8
AFT
TUNING FREQUANCY (LOWER PART) S-SYS
TUNING FREQUANCY (HIGHER PART)
F7
F6
(auto)
F5
AFT
TUNING FREQUANCY (LOWER PART) S-SYS
TUNING FREQUANCY (HIGHER PART)
F4
F3
(auto)
F2
AFT
TUNING FREQUANCY (LOWER PART)
D5
TUNING FREQUANCY (HIGHER PART)
F1
S-SYS
S-SYS
S-SYS
S-SYS
S-SYS
S-SYS
S-SYS
S-SYS
S-SYS
S-SYS
S-SYS
S-SYS
S-SYS
S-SYS
S-SYS
S-SYS
S-SYS
D6
EF
D7
F0
EE
ED
EC
EB
EA
E9
E8
E7
E6
E5
E4
E3
E2
E1
E0
DF
DE
DD
DC
DB
DA
D9
D8
D7
D6
D5
D4
D3
D2
D1
D0
CF
CE
CD
CC
CB
CA
C9
C8
C7
C6
C5
C4
C3
C2
C1
C0
(HEX)
ADDRESS CHECK TYPE
CHASSIS CHECK DATA
CHECK TYPE
CTV FINAL CHECK DATA
LAST INITIAL SETTING DATA REMARK
POS 46
POS 45
POS 44
POS 43
POS 42
POS 41
POS 40
POS 39
POS 38
POS 37
POS 36
POS 35
POS 34
POS 33
POS 32
POS 31
POS 30
POS 29
POS 28
POS 27
POS 26
POS 25
14D1-S/G/W 14D2-S/G
D6
AFT
D4
DATA
D3
(auto)
D2
(auto)
13
(auto)
13F
13-1
RANGE
EEPROM
EEPROM WRITE(CPU)
LETTER NO.
C-SYS
C-SYS
C-SYS
C-SYS
C-SYS
C-SYS
C-SYS
C-SYS
C-SYS
C-SYS
C-SYS
C-SYS
C-SYS
C-SYS
C-SYS
C-SYS
C-SYS
C-SYS
C-SYS
C-SYS
C-SYS
MICON DEFAULT
LETTER NO.
(auto)
D0 C-SYS
MODEL
AFT
D1
MODEL
S-SYS
(auto)
13E
AFT
TUNING FREQUANCY (HIGHER PART)
TUNING FREQUANCY (LOWER PART)
13D
13C
S-SYS
(auto)
TUNING FREQUANCY (LOWER PART)
AFT
TUNING FREQUANCY (HIGHER PART)
13B
139
13A
S-SYS
(auto)
TUNING FREQUANCY (LOWER PART)
138
AFT
TUNING FREQUANCY (HIGHER PART)
137
136
S-SYS
(auto)
TUNING FREQUANCY (LOWER PART)
135
AFT
TUNING FREQUANCY (HIGHER PART)
134
133
S-SYS
(auto)
TUNING FREQUANCY (LOWER PART)
AFT
TUNING FREQUANCY (HIGHER PART)
131
130
132
S-SYS
(auto)
TUNING FREQUANCY (LOWER PART)
AFT
TUNING FREQUANCY (HIGHER PART)
12E
12F
12D
TUNING FREQUANCY (LOWER PART)
AFT
TUNING FREQUANCY (HIGHER PART)
S-SYS
(auto)
12C
S-SYS
AFT
TUNING FREQUANCY (LOWER PART)
TUNING FREQUANCY (HIGHER PART)
12B
12A
129
128
127
S-SYS
(auto)
TUNING FREQUANCY (LOWER PART)
126
AFT
TUNING FREQUANCY (HIGHER PART)
125
124
S-SYS
(auto)
TUNING FREQUANCY (LOWER PART)
123
AFT
TUNING FREQUANCY (HIGHER PART)
122
121
S-SYS
(auto)
TUNING FREQUANCY (LOWER PART)
AFT
TUNING FREQUANCY (HIGHER PART)
11F
11E
120
S-SYS
(auto)
TUNING FREQUANCY (LOWER PART)
AFT
TUNING FREQUANCY (HIGHER PART)
11D
11B
11C
S-SYS
(auto)
TUNING FREQUANCY (LOWER PART)
AFT
TUNING FREQUANCY (HIGHER PART)
119
118
11A
S-SYS
(auto)
TUNING FREQUANCY (LOWER PART)
117
AFT
TUNING FREQUANCY (HIGHER PART)
116
115
S-SYS
(auto)
TUNING FREQUANCY (LOWER PART)
114
AFT
TUNING FREQUANCY (HIGHER PART)
113
112
S-SYS
AFT
TUNING FREQUANCY (HIGHER PART)
TUNING FREQUANCY (LOWER PART)
10F
110
111
S-SYS
(auto)
TUNING FREQUANCY (LOWER PART)
10E
AFT
TUNING FREQUANCY (HIGHER PART)
10D
10C
S-SYS
(auto)
TUNING FREQUANCY (LOWER PART)
AFT
TUNING FREQUANCY (HIGHER PART)
10B
109
10A
S-SYS
(auto)
TUNING FREQUANCY (LOWER PART)
108
AFT
TUNING FREQUANCY (HIGHER PART)
107
S-SYS
TUNING FREQUANCY (LOWER PART)
105
106
TUNING FREQUANCY (HIGHER PART)
(auto)
104
AFT
TUNING FREQUANCY (LOWER PART)
D5
TUNING FREQUANCY (HIGHER PART)
103
S-SYS
S-SYS
102
D7
101
100
(HEX)
ADDRESS CHECK TYPE
CHASSIS CHECK DATA
CHECK TYPE
CTV FINAL CHECK DATA
LAST INITIAL SETTING DATA REMARK
POS 67
POS 66
POS 65
POS 64
POS 63
POS 62
POS 61
POS 60
POS 59
POS 58
POS 57
POS 56
POS 55
POS 54
POS 53
POS 52
POS 51
POS 50
POS 49
POS 48
POS 47
POS 46
17F
17E
17D
17C
17B
17A
179
178
177
176
175
174
173
172
171
170
16F
16E
16D
16C
16B
16A
169
168
167
166
165
164
163
162
161
160
15F
15E
15D
15C
15B
15A
159
158
157
156
155
154
153
152
151
150
14F
14E
14D
14C
14B
14A
149
148
147
146
145
144
143
142
141
140
(HEX)
ADDRESS
LETTER NO.
MODEL
D7
S-SYS
S-SYS
S-SYS
S-SYS
S-SYS
S-SYS
S-SYS
S-SYS
S-SYS
S-SYS
S-SYS
S-SYS
S-SYS
S-SYS
S-SYS
S-SYS
S-SYS
S-SYS
S-SYS
S-SYS
S-SYS
D6
D5
D4
DATA D3
D2
(auto)
(auto)
(auto)
(auto)
(auto)
(auto)
(auto)
(auto)
(auto)
(auto)
(auto)
(auto)
(auto)
(auto)
(auto)
(auto)
(auto)
(auto)
(auto)
(auto)
(auto) TUNING FREQUANCY (HIGHER PART)
AFT
TUNING FREQUANCY (LOWER PART)
TUNING FREQUANCY (HIGHER PART)
AFT
TUNING FREQUANCY (LOWER PART)
TUNING FREQUANCY (HIGHER PART)
AFT
TUNING FREQUANCY (LOWER PART)
TUNING FREQUANCY (HIGHER PART)
AFT
TUNING FREQUANCY (LOWER PART)
TUNING FREQUANCY (HIGHER PART)
AFT
TUNING FREQUANCY (LOWER PART)
TUNING FREQUANCY (HIGHER PART)
AFT
TUNING FREQUANCY (LOWER PART)
TUNING FREQUANCY (HIGHER PART)
AFT
TUNING FREQUANCY (LOWER PART)
TUNING FREQUANCY (HIGHER PART)
AFT
TUNING FREQUANCY (LOWER PART)
TUNING FREQUANCY (HIGHER PART)
AFT
TUNING FREQUANCY (LOWER PART)
TUNING FREQUANCY (HIGHER PART)
AFT
TUNING FREQUANCY (LOWER PART)
TUNING FREQUANCY (HIGHER PART)
AFT
TUNING FREQUANCY (LOWER PART)
TUNING FREQUANCY (HIGHER PART)
AFT
TUNING FREQUANCY (LOWER PART)
TUNING FREQUANCY (HIGHER PART)
AFT
TUNING FREQUANCY (LOWER PART)
TUNING FREQUANCY (HIGHER PART)
AFT
TUNING FREQUANCY (LOWER PART)
TUNING FREQUANCY (HIGHER PART)
AFT
TUNING FREQUANCY (LOWER PART)
TUNING FREQUANCY (HIGHER PART)
AFT
TUNING FREQUANCY (LOWER PART)
TUNING FREQUANCY (HIGHER PART)
AFT
TUNING FREQUANCY (LOWER PART)
TUNING FREQUANCY (HIGHER PART)
AFT
TUNING FREQUANCY (LOWER PART)
TUNING FREQUANCY (HIGHER PART)
AFT
TUNING FREQUANCY (LOWER PART)
TUNING FREQUANCY (HIGHER PART)
AFT
TUNING FREQUANCY (LOWER PART)
TUNING FREQUANCY (HIGHER PART)
AFT
TUNING FREQUANCY (LOWER PART)
TUNING FREQUANCY (HIGHER PART)
D1
MICON
MODEL
RANGE
EEPROM
EEPROM WRITE(CPU)
LETTER NO.
DEFAULT
13-2
C-SYS
C-SYS
C-SYS
C-SYS
C-SYS
C-SYS
C-SYS
C-SYS
C-SYS
C-SYS
C-SYS
C-SYS
C-SYS
C-SYS
C-SYS
C-SYS
C-SYS
C-SYS
C-SYS
C-SYS
C-SYS
D0 CHECK TYPE
CHASSIS CHECK DATA
CHECK TYPE
CTV FINAL CHECK DATA
LAST INITIAL SETTING DATA
REMARK
POS 89
POS 88
POS 87
POS 86
POS 85
POS 84
POS 83
POS 82
POS 81
POS 80
POS 79
POS 78
POS 77
POS 76
POS 75
POS 74
POS 73
POS 72
POS 71
POS 70
POS 69
POS 68
14D1-S/G/W 14D2-S/G
D4
DATA
D3
D2
AFT
(auto)
TUNING FREQUANCY (LOWER PART)
CHECK TYPE
CTV FINAL CHECK DATA
LAST INITIAL SETTING DATA REMARK
AV2
AV1
POS 99
POS 98
POS 97
POS 96
POS 95
POS 94
POS 93
POS 92
POS 91
POS 90
POS 89
1E5
1E4
1E3
1E2
1E1
1E0
1DF
1DE
1DD
1DC
1DB
1DA
1D9
1D8
1D7
1D6
1D5
1D4
1D3
1D2
1D1
1D0
1CF
1CE
1CD
1CC
1CB
1CA
1C9
1C8
1C7
1C6
1C5
1C4
1C3
1C2
1C1
1C0
(HEX)
ADDRESS
14 1F9 1FA 1FB
1B9
1BA
1BB
MODEL
LETTER NO.
MODEL
LETTER NO.
1FF
1F8
1B8
1FE
1F7
1B7
1BF
1F6
1B6
1FC
1F5
1B5
1BE
1F4
1B4
1FD
1F3
1B3
1BD
1F2
1B2
1BC
1EF 1F1
1B1
1EE 1F0
1AE
1AF
1ED
1AD
1B0
1EB 1EC
1AC
1E9
1AB
1EA
1AA
1E8
CHECK TYPE
CHASSIS CHECK DATA
1A9
14-1
EEPROM WRITE(CPU)
1E7
C-SYS
C-SYS
C-SYS
RANGE
EEPROM
1E6
(auto)
(auto)
(auto)
MICON DEFAULT
1A8
AFT
C-SYS
C-SYS
C-SYS
C-SYS
C-SYS
C-SYS
C-SYS
C-SYS
C-SYS
C-SYS
D0
1A7
S-SYS
D1
1A6
1A5
1A4
1A3
1A2
1A1
1A0
19F
TUNING FREQUANCY (LOWER PART)
(auto)
19E
AFT
TUNING FREQUANCY (HIGHER PART)
S-SYS
19D
19C
TUNING FREQUANCY (LOWER PART)
(auto)
19B
AFT
TUNING FREQUANCY (HIGHER PART)
S-SYS
19A
199
TUNING FREQUANCY (LOWER PART)
(auto)
198
AFT
TUNING FREQUANCY (HIGHER PART)
S-SYS
197
196
TUNING FREQUANCY (LOWER PART)
195
(auto)
TUNING FREQUANCY (HIGHER PART)
AFT
TUNING FREQUANCY (LOWER PART)
194
S-SYS
192
193
TUNING FREQUANCY (HIGHER PART)
(auto)
191
AFT
TUNING FREQUANCY (LOWER PART)
S-SYS
TUNING FREQUANCY (HIGHER PART)
190
18F
(auto)
18E
AFT
TUNING FREQUANCY (LOWER PART)
18D
S-SYS
(auto)
18C
AFT
TUNING FREQUANCY (HIGHER PART)
S-SYS
18B
18A
TUNING FREQUANCY (LOWER PART)
189
(auto)
TUNING FREQUANCY (HIGHER PART)
AFT
188
S-SYS
TUNING FREQUANCY (LOWER PART)
186
187
TUNING FREQUANCY (HIGHER PART)
(auto)
185
AFT
TUNING FREQUANCY (LOWER PART)
D5
TUNING FREQUANCY (HIGHER PART)
184
S-SYS
S-SYS
D6
183
D7
182
181
180
(HEX)
ADDRESS
LETTER NO.
MODEL
D7
D6
D5
D4
DATA D3
D2
D1
MICON
MODEL
RANGE
EEPROM
EEPROM WRITE(CPU)
LETTER NO.
DEFAULT
14-2
D0 CHECK TYPE
CHASSIS CHECK DATA
CHECK TYPE
CTV FINAL CHECK DATA
LAST INITIAL SETTING DATA REMARK
14D1-S/G/W 14D2-S/G
15-1
Check R618 and R619.
Check D751
Check R701 and R707
15
Check IC801.
15-2
Check Q752 and IC801.
Does horizontal circuit oscillate ?
Check C878.
Check CRT connector K1-K5 bias.
Check Secondary Main+B (Approx. 130V)
Check T701 pin (11) voltage (Approx. 310V at 220V AC)
Check F701.
NO RASTER
Replace the fuse.
Blown out.
Checking the protector circuit.
D1001 (Power LED Red dimly) turns on or turns ON/OFF.
D1001 (Power LED Red brightly) turns on.
Check IC701, D701 and C705.
The fuse is again blown out.
TROUBLE SHOOTING TABLE
14D1-S/G/W 14D2-S/G
16 16-1
Check P302,P303 connector of IC302 and peripheral circuit.
Does signal appear at pins (2) and (4) of IC302 ?
Check pin (37)of IC801 and related circuit.
Check Q251, Q252 and related circuit.
Check IC801 and its related circuit.
Check IC801.
Check Q321, pins(4) and (6) of IC801 and peripheral circuit.
Check C356, C359 and peripheral circuit.
Does signal appear at pins(28) and (29) of IC801?
Check pin (1) of SF201 and Tuner related circuit.
Does noise or signal appear at pins (23) and (24)of IC801.
Does noise or signal appear at pin (38) of IC801 ?
NO SOUND
Does noise signal appear at pin (44) of IC801 ?
Check pin (27) of IC801, Tuner and related circuit.
CIRCUITS TO BE CHECKED: » Sound system pins (28), (29) and (44) of IC801. » Sound Detector Circuit. » Sound Switch and Att. Control. » Audio Output Circuit.
Check pin(38) of IC801.
Check the tuner AGC (TP201).
Check the tuner supply voltage LB must be approx. 5V. BT must be approx, 32V. And CH preset data check.
No snow noise.
Does noise or signal appear at pin (40) of IC801 ?
Does the noise level increase at max. Contrast, Brightness and Sound controls ?
NO PICTURE, NO SOUND
Noise increases but no signal is received.
CIRCUITS TO BE CHECKED: » Tuner. » PIF. » Automatic Gain Control. » (5V), (32V) Power Source.
TROUBLE SHOOTING TABLE (Continued)
Check pins(33) and (34) of IC801.
Check C505 and C509.
16-2
Check IC501.
Check IC501.
NO VERTICAL SCAN
Check R501, R503, R512, R521, R533 and C533.
Vertical linearity and size is abnormal.
Readjust vertical size. (Bas Data)
DEFECTIVE VERTICAL AMP. AND VERTICAL LINEARITY
CIRCUIT TO BE CHECKED: » Sync. Separator Circuit.
NEITHER VERTICAL NOR HORIZONTAL SYNCHRONIZATION
TROUBLE SHOOTING TABLE (Continued)
14D1-S/G/W 14D2-S/G
Check Q870, Q885 and their adjacent circuits.
Check Q871, Q883 and their adjacent circuits.
17
Check Q872, Q887 and their adjacent circuits.
The picture colour is yellow.
Readjust the white balance.
Is the white balance properly adjusted ?
17-1
Check X1001.(12MHz)
Check IC801 and bias control circuit.
“PAL”/“SECAM” (NO COLOUR SYNCHRONIZATION)
NO SPECIFIC COLOUR
The picture colour is magenta.
The picture colour is cyan.
Check IC801, R801, R802, R803, D804, D805, D806 and Q801.
Is some colour produced in B/W broadcast reception ?
NO SPECIFIC COLOUR
TROUBLE SHOOTING TABLE (Continued)
17-2
14D1-S/G/W 14D2-S/G
14D1-S/G/W 14D2-S/G
WAVEFORMS(14D1-S/G/W)
1) 1.0 Vp-p
2) 3.00 Vp-p (H)
3) 3.10 Vp-p (H)
4) 3.10 Vp-p (H)
5) 70.0 Vp-p (H)
6) 78.4 Vp-p (H)
7) 79.2 Vp-p (H)
8) 3.2 Vp-p (H)
9) 2.32 Vp-p (H)
10) 122 Vp-p (H)
11) 8.8 Vp-p (H)
12) 50 Vp-p (H)
13) 110 Vp-p (H)
14) 1100Vp-p (H)
15) 480 Vp-p (H)
16) 28 Vp-p (H)
17) 2.08 Vp-p (H)
18
14D1-S/G/W 14D2-S/G
WAVEFORMS(14D2-S/G)
1) 1.0 Vp-p
2) 3.00 Vp-p (H)
3) 3.10 Vp-p (H)
4) 3.10 Vp-p (H)
5) 70.0 Vp-p (H)
6) 78.4 Vp-p (H)
7) 79.2 Vp-p (H)
8) 3.2 Vp-p (H)
9) 2.32 Vp-p (H)
10) 122 Vp-p (H)
11) 8.8 Vp-p (H)
12) 50 Vp-p (H)
13) 110 Vp-p (H)
14) 1.1 kVp-p (H)
15) 480 Vp-p (H)
16) 28 Vp-p (H)
17) 2.08 Vp-p (H)
19
14D1-S/G/W 14D2-S/G
SOLID STATE DEVICE BASE DIAGRAM TOP VIEW 8
5
1
4
COLLECTOR
ZR
:BR:
BASE
CAT24W04 (BR24C04) (M24C04W)
64
COLLECTOR
BASE
EMITTER
EMITTER
B709A
D601A
33
1
32
IX3368CE
SIDE VIEW
+ BASE COLLECTOR EMITTER
TX0110BM TX0124BM 2SC3198
BASE COLLECTOR EMITTER
~
~
-
DX0111PE
2SC3207
CATHODE ANODE (RED)
1
1 2 3
AN7523 KA7808A B
C
E
PX0013PE
2SD2586
1
STRG5653
2 4 3 5
9
AN5522
20
9
14D1-S/G/W 14D2-S/G
MODEL 14D1-S/G/W CHASSIS LAYOUT
21
14D1-S/G/W 14D2-S/G
MODEL 14D2-S/G CHASSIS LAYOUT
22
14D1-S/G/W 14D2-S/G
BLOCK DIAGRAM:CRT UNIT
BLOCK DIAGRAM:HEADPHONE UNIT
23
14D1-S/G/W 14D2-S/G
14D1-S/G/W 14D2-S/G
MODEL 14D1-S/G/W BLOCK DIAGRAM:MAIN UNIT
24~25
14D1-S/G/W 14D2-S/G
14D1-S/G/W 14D2-S/G
MODEL 14D2-S/G BLOCK DIAGRAM:MAIN UNIT
26~27
14D1-S/G/W 14D2-S/G
DESCRIPTION OF SCHEMATIC DIAGRAM SAFETY NOTES:
NOTES:
1. DISCONNECT THE AC PLUG FROM THE AC OUTLET BEFORE REPLACING PARTS. 2. SEMICONDUCTOR HEAT SINKS SHOULD BE REGARDED AS POTENTIAL SHOCK HAZARDS WHEN THE CHASSIS IS OPERATING.
1. The unit of resistance "ohm" is omitted. (K = 1000 ohms, M = Mega ohm). 2. All resistors are 1/10 watt, unless otherwise noted. 3. All capacitors are µF, unless otherwise noted. (P = µµF).
IMPORTANT SAFETY NOTICE:
VOLTAGE MEASUREMENT CONDITIONS:
PARTS MARKED WITH " å " ( ) ARE IMPOTANT FOR MAINTAINING THE SAFETY OF THE SET. BE SURE TO REPLACE THESE PARTS WITH SPECIFIED ONES FOR MAINTAINING THE SAFETY AND PERFORMANCE OF THE SET.
1. Voltages in parenthesis measured with no signal. 2. Voltages without parenthesis measured with 3mV B & W or Colour signal. 3. All the voltages in each point are measured with VTVM.
SERVICE PRECAUTION: THE AREA ENCLOSED BY THIS LINE ( —– - —– ) IS DIRECTLY CONNECTED WITH AC MAINS VOLTAGE. WHEN SERVICING THE AREA, CONNECT AN ISOLATING TRANSFORMER BETWEEN TV RECEIVER AND AC LINE TO ELIMINATE HAZARD OF ELECTRIC SHOCK.
WAVEFORM MEASUREMENT CONDITIONS: 1. The colour bar generator signal of 2.0V peak applied at of Base Video Buffer Amp. Q252. 2. Approximately 4V AGC bias .
28
14D1-S/G/W 14D2-S/G
SCHEMATIC DIAGRAM:CRT UNIT J
I
H
G
F
SCHEMATIC DIAGRAM:HEADPHONE UNIT E
D
C
B
A
1
2
3
4
5
6
29
7
8
9
10
14D1-S/G/W 14D2-S/G
14D1-S/G/W 14D2-S/G
SCHEMATIC DIAGRAM:MAIN UNIT (14D1-S/G/W)
J
I
H
G
F
E
D
C
B
A
1
2
3
4
5
6
7
8
9
10
11
30~31
12
13
14
15
16
17
18
19
20
14D1-S/G/W 14D2-S/G
14D1-S/G/W 14D2-S/G
SCHEMATIC DIAGRAM:MAIN UNIT (14D2-S/G)
J
I
H
G
F
E
D
C
B
A
1
2
3
4
5
6
7
8
9
10
11
32~33
12
13
14
15
16
17
18
19
20
14D1-S/G/W 14D2-S/G
14D1-S/G/W 14D2-S/G
PRINTED WIRING BOARD ASSEMBLIES PWB-A: MAIN UNIT (WIRING SIDE) J
I
H
G
F
E
D
C
B
A
1
2
3
4
5
6
7
8
9
10
11
34~35
12
13
14
15
16
17
18
19
20
14D1-S/G/W 14D2-S/G
14D1-S/G/W 14D2-S/G
PWB-A: MAIN UNIT (Chip Parts Side) J
I
H
G
F
E
D
C
B
A
1
2
3
4
5
6
7
8
9
10
11
36~37
12
13
14
15
16
17
18
19
20
14D1-S/G/W 14D2-S/G
J
I
H
PWB-B: CRT UNIT (WIRING SIDE) G
F
E
PWB-B: CRT UNIT (Chip Parts Side) D
C
PWB-C: HEADPHONE UNIT (WIRING SIDE)
R J 61
B R 371
R J 62
R 370
R J 60
PWB-B: HEADPHONE UNIT (Chip Parts Side) A
1
2
3
4
5
6
38
7
8
9
10
14D1-S/G/W 14D2-S/G Part No. ★ Description Code REPLACEMENT PARTS LIST
Ref. No.
Ref. No.
"HOW TO ORDER REPLACEMENT PARTS" To have your order filled promptly and correctly, please furnish the following informations. 1. MODEL NUMBER 3. PART NO.
MARK Ref. No.
VTUCTF5511+++
IC302 å IC501 IC601 IC701 IC801 IC1005
VHiAN7523++-1 VHiAN5522++-1 VHiKA7808AP-1 VHiSTRG5653-1 RH-iX3368CEN6 VHiCAT24W04-1
Description
VB37GDA86X/1E RCiLG0095PEZZ RCiLH0225PEZZ PMAGF3045CEZZ QEARC1422PEZZ
R R R R R
Picture Tube Degaussing Coil Deflection Yoke Magnet Ground-part
Code
CB AH AX AG AD
PRINTED WIRING BOARD ASSEMBLIES (NOT REPLACEMENT ITEM) PWB-A PWB-A PWB-A PWB-B PWB-B PWB-B PWB-C
DUNTKB508WEA4 DUNTKB508WEA5 DUNTKB508WEA8 DUNTKB509WEA4 DUNTKB509WEA5 DUNTKB509WEA8 DUNTKB510WEA3
-
Main Unit (14D1-S/G) Main Unit (14D2-S/G) Main Unit (14D1-W) CRT Unit (14D1-S/G) CRT Unit (14D2-S/G) CRT Unit (14D1-W) Headphone Unit
AZ
R R R R R R
AN7523 AN5522 KIA7808API STR-G5653 I.C. I.C.
AH AH AE AQ BE AE
TRANSISTORS
PICTURE TUBE å å å DY601
R VHF Tuner
INTEGRATED CIRCUITS
: SPARE PARTS-DELIVERY SECTION. ★
Code
TUNER å TU201
2. REF. NO. 4. DESCRIPTION
Part No.
Description
DUNTKB508WEA4(14D1-S/G) DUNTKB508WEA5(14D1-S/G) DUNTKB508WEA8(14D1-W) PWB-A MAIN UNIT
PARTS REPLACEMENT Replacement parts which have these special safety characteristics are identified in this manual; electrical components having such features are identified by "å" in the Replacement Parts Lists. The use of a substitute replacement part which does not have the same safety characteristics as the factory recommended replacement parts shown in this service manual may create shock, fire or other hazards.
★
Part No.
Q251 Q251 Q252 Q302 Q302 Q321 Q321 Q352 Q352 Q501 Q601 Q602 Q603 Q751 Q752 Q801 Q801 Q802 Q802 Q804 Q1010 Q1010
VS2SD601A//-1Y VS2PD601AR/-1Y VS2PC1815G+-1+ VS2SD601A//-1Y VS2PD601AR/-1Y VS2SD601A//-1Y VS2PD601AR/-1Y VS2SD601A//-1Y VS2PD601AR/-1Y VS2PC1815G+-1+ VS2SC3207//-1+ VS2SD2586//1E VS2PC1815G+-1+ VS2PC1815G+-1+ VS2PC1815G+-1+ VS2SB709A//-1Y VS2PB709AR/-1Y VS2SB709A//-1Y VS2PB709AR/-1Y VS2PD601AR/-1Y VS2SD601A//-1Y VS2PD601AR/-1Y
D201 D203 D301 D302 D331 D332 D503 D505 D506 D507 D508 D509 D531 D532 D601 D602 D603 D604 D606 D607 D608 D651 D652 D653 D701 D705 D706 D707 D751 D752 D754 D755 D801
RH-EX0676GEZZY RH-DX0045GEZZY VHD1SS119//-1Y VHD1SS119//-1Y RH-DX0302CEZZY RH-DX0445CEZZ RH-DX0045GEZZY RH-DX0441CEZZY RH-EX0630GEZZY RH-DX0045GEZZY RH-DX0131CEZZY RH-EX0660GEZZY RH-EX0627GEZZY RH-EX0627GEZZY RH-DX0048GEZZY VHD1SS244//-1Y RH-EX0667GEZZY VHD1SS119//-1Y RH-DX0131CEZZY RH-DX0045GEZZY RH-DX0468CEZZ RH-EX0627GEZZY RH-EX0253TAZZY RH-DX0045GEZZY RH-DX0111PEZZ VHD1SS82///1AY VHD1SS82///1AY VHD1SS82///1AY RH-DX0229CEZZ RH-DX0131CEZZY RH-EX0616GEZZY RH-EX0603GEZZY VHD1SS119//-1Y
R R R R R R R R R R R R R R R R R R R R R R
2SD601A(14D1-S/G/W) 2PD601AR(14D2-S/G) 2PC1815G 2SD601A (14D1-S/G/W) 2PD601AR (14D2-S/G) 2SD601A (14D1-S/G/W) 2PD601AR (14D2-S/G) 2SD601A (14D1-S/G/W) 2PD601AR (14D2-S/G) 2PC1815G 2SC3207 2SD2586 2PC1815G 2PC1815G 2PC1815G 2SB709A (14D1-S/G/W) 2PB709AR (14D2-S/G) 2SB709A (14D1-S/G/W) 2PB709AR (14D2-S/G) 2PD601AR 2SD601A (14D1-S/G/W) 2PD601AR (14D2-S/G)
AC AB AC AC AB AC AB AC AB AC AC AM AC AC AC AA AB AA AB AB AC AB
DIODES AND LED’S — — — — — — —
39
R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R
Zener Diode 32.5V Diode 1SS119 1SS119 Diode (14D1-S/G/W) Diode (14D2-S/G) Diode Diode Zener Diode 9V Diode Diode Zener Diode 22.2V Zener Diode 8.2V Zener Diode 8.2V Diode 1SS244 Zener Diode 26.3V 1SS119 Diode Diode Diode Zener Diode 8.2V Zener Diode Diode Diode 1SS82 1SS82 1SS82 Diode Diode Zener Diode 5.9V Zener Diode 4V 1SS119
AA AA AA AA AC AL AA AC AA AA AC AB AA AA AA AB AA AA AC AA AE AA AC AA AG AC AC AC AF AC AA AA AA
14D1-S/G/W 14D2-S/G Ref. No. D802 D803 D804 D805 D806 D808 D1001 D1003 D1004 D1007 D1012 D1018 D1019 D1024 å VA701
Part No. RH-DX0045GEZZY RH-DX0045GEZZY RH-DX0045GEZZY RH-DX0045GEZZY RH-DX0045GEZZY RH-EX0610GEZZY RH-PX0013PEZZ VHD1SS119//-1Y VHD1SS119//-1Y RH-EX0263TAZZY RH-EX0611GEZZY RH-EX0263TAZZY RH-EX0263TAZZY VHD1SS119//-1Y RH-VX0073CEZZ
★
Description
Code
Ref. No.
R R R R R R R R R R R R R R R
Diode Diode Diode Diode Diode Zener Diode 4.9V PhotoDiode 1SS119 1SS119 Zener Diode Zener Diode 5V Zener Diode Zener Diode 1SS119 Varistor
AA AA AA AA AA AA AC AA AA AC AA AC AC AA AD
C509 C510 C514 C529 C531 C532 C533 C601 C602 C603 C604 C605 C606 C607 C608 C610 C611 C612 C620 C640 C651 C652 C653 C654 C655 C656 C657 C658 å C701 C702 C703 C704 C705 C709 C710 C711 C712 å C751 C752 C753 C754 C755 C756 C759 C760 C801 C803 C804 C805 C806 C807 C808 C809 C810 C811 C812 C813 C814 C816 C1001 C1002 C1003 C1004 C1005 C1006 C1008 C1009 C1010 C1011 C1012 C1013 C1014 C1016 C1018 C1019 C1024
PACKAGED CIRCUITS PR702 X1001
RMPTP0028CEZZ R Packaged Circuit RCRSB0300CEZZ R Crystal
CF251 CF252 L202 L203 L251 L252 L701 L751 L802 L803 L1030 L1050 L1051 SF201 T601 T602 T701
RFiLC0318CEZZ RFiLC0465CEZZ VP-DF270K0000Y VP-DF270K0000Y VP-XF100K0000Y VP-XF6R8K0000Y RCiLF0096PEZZ RCiLP0225CEZZ VP-DF100K0000Y VP-DF100K0000Y VP-DF100K0000Y VP-DF100K0000Y VP-DF100K0000Y RFiLC0442CEZZ RTRNZ0144PEZZ RTRNF0228PEZZ RTRNW0015PEZZ
C201 C202 C203 C204 C205 C206 C231 C232 C233 C234 C251 C252 C301 C304 C306 C310 C311 C312 C316 C331 C332 C333 C352 C354 C356 C359 C360 C409 C410 C411 C412 C501 C504 C505 C507 C508
VCEA0A1CW476M+R VCEA0A1AW337M+R VCKYCY1HF103Z R VCEA0A0JW477M+ R VCKYCY1HF103Z R VCEA0A1HW106M+R VCKYCY1HF223Z R VCKYCY1HB821K R VCKYCY1HB472K R VCKYCY1EF104Z R VCKYCY1HF223Z R VCEA0A1CW107M+R VCEA0A1CW477M+R VCEA0A1CW106M+R VCEA0A1CW106M+R VCEA0A1HW105M+R VCEA0A1HW105M+R VCEA0A1HW224M+R VCEA0A1CW107M+R VCKYPA2HB102K+ R RC-QZA103TAYJ+ R VCEA0A1CW108M R VCEA0A1HW105M+R VCEA0A1HW105M+R VCKYCY1HB472K R VCEA0A1CW106M+R VCE9GA1HW225M+R VCKYCY1CF474Z R VCKYCY1CF474Z R VCKYCY1HB102K R VCEA0A1CW477M+R VCKYPA1HB102K+ R VCKYCY1HB103K R VCEA0A1HW107M+R VCKYCY1HB103K R VCFYSA1JB224J+ R
AG AF
COILS AND TRANSFORMER
å
å å å
R R R R R R R R R R R R R R R R R
Filter Filter Peaking 27µH Peaking 27µH Peaking 10µH Peaking 6.8µH Coil Coil Peaking 10µH Peaking 10µH Peaking 10µH Peaking 10µH Peaking 10µH Filter Transformer H-Volt Transformer Transformer
AG AD AB AB AB AB AF AF AB AB AB AB AB AL AE AX AL
CAPACITORS 47 330 0.01 470 0.01 10 0.022 820p 4700p 0.1 0.022 100 470 10 10 1 1 0.22 100 1000p 0.01 1000 1 1 4700p 10 2.2 0.47 0.47 1000p 470 1000p 0.01 100 0.01 0.22
16V Electrolytic AB 10V Electrolytic AC 50V Ceramic AA 6.3V Electrolytic AC 50V Ceramic AA 50V Electrolytic AB 50V Ceramic AB 50V Ceramic AA 50V Ceramic AA 25V Ceramic AA 50V Ceramic AB 16V Electrolytic AC 16V Electrolytic AC 16V Electrolytic AB 16V Electrolytic AB 50V Electrolytic AB 50V Electrolytic AB 50V Electrolytic AB 16V Electrolytic AC 500V Ceramic AA 50V M.Polyester Film AB 16V Electrolytic AD 50V Electrolytic AB 50V Electrolytic AB 50V Ceramic AA 16V Electrolytic AB 50V Elect.(N,P) AB 16V Ceramic AB 16V Ceramic AB 50V Ceramic AA 16V Electrolytic AC 50V Ceramic AA 50V Ceramic AA 50V Electrolytic AB 50V Ceramic AA 63V Mylar AD
40
Part No.
★
VCEA0A1CW477M+R VCKYPA2HB102K+ R VCFYSA1JB563J+ R VCKYCY1CB823KY R VCKYCY1HB102K R VCKYCY1HB102K R RC-QZA104TAYJ+ R RC-QZA563TAYJ+ R VCEA0A1HW475M+R VCEA0A1HW105M+R VCEA0A2EW106M R VCKYPA2HB102K+ R VCFPFA2EB334J R VCFPFD3ZA532H R VCKYPA2HB102K+ R VCEA0A1CW108M R VCEA0A1EW476M+R VCEA0A1CW477M+R VCKYPA2HB102K+ R VCFYSB2EB823J R VCQYTA1HM222J+ R RC-QZA472TAYJ+ R VCEA0A1HW105M+R VCKYCY1HF223Z R VCEA0A1HW106M+R VCEA0A1HW474M+R VCKYCY1EF104Z R VCKYCY1EF104Z R RC-FZ031SCEZZ R RC-KZ0029CEZZ+ R RC-KZ0029CEZZ+ R RC-KZ0029CEZZ+ R RC-EZ1286CEZZ R RC-KZ0039CEZZ R VCEA0A1HW476M+R VCKYPA1HB102K+ R VCKYPA1HB471K+ R RC-KZ0102GEZZ R VCKYPH3DB561K R RC-EZ0776CEZZ R RC-EZA069WJZZ R VCEA0A1CW108M R RC-QZA103TAYJ+ R VCEA0A0JW477M+ R VCEA0A0JW228M R VCEA0A1HW105M+R VCEA0A1CW107M+R VCKYCY1HB222K R VCKYD41HB102KY R VCKYD41HB102KY R VCKYD41HB102KY R VCEA0A1CW107M+R VCKYCY1CF474Z R VCKYCY1CF474Z R VCEA0A1CW107M+R VCFYFA1HA224J+ R VCFYFA1HA224J+ R VCKYCY1HB471K R VCKYCY1HB471K R VCEA0A0JW107M+ R VCEA0A0JW107M+ R VCEA0A1CW106M+R VCKYCY1CF474Z R VCKYCY1CF474Z R VCEA0A1CW106M+R VCCCCY1HH330J R VCCCCY1HH330J R VCEA0A0JW107M+ R VCKYCY1CF474Z R VCKYCY1CF474Z R VCEA0A0JW107M+ R VCEA0A1CW106M+R RC-QZA104TAYJ+ R VCKYCY1HB221K R VCEA0A1HW225M+R RC-QZA104TAYJ+ R
Description 470 1000p 0.056 0.082 1000p 1000p 0.1 0.056 4.7 1 10 1000p 0.33 5300p 1000p 1000 47 470 1000p 0.082 2200p 4700p 1 0.022 10 0.47 0.1 0.1 0.1 0.01 0.01 0.01 150 680p 47 1000p 470p 680 560p 100 33 1000 0.01 470 2200 1 100 2200p 1000p 1000p 1000p 100 0.47 0.47 100 0.22 0.22 470p 470p 100 100 10 0.47 0.47 10 33p 33p 100 0.47 0.47 100 10 0.1 220p 2.2 0.1
Code
16V Electrolytic AC 500V Ceramic AA 63V Mylar AD 16V Ceramic AH 50V Ceramic AA 50V Ceramic AA 50V M.Polyester Film AB 50V M.Polyester Film AB 50V Electrolytic AB 50V Electrolytic AB 250V Electrolytic AD 500V Ceramic AA 250V M.Polypro AD 1.8kVM.Polypro AD 500V Ceramic AA 16V Electrolytic AD 25V Electrolytic AB 16V Electrolytic AC 500V Ceramic AA 250V M.Polyester Film AD 50V Mylar AA 50V Mylar AB 50V Electrolytic AB 50V Ceramic AB 50V Electrolytic AB 50V Electrolytic AB 25V Ceramic AA 25V Ceramic AA 275V M.Polyester Film AD 250V Ceramic AC 250V Ceramic AC 250V Ceramic AC 400V Electrolytic AT 2kV Ceramic AB 50V Electrolytic AB 50V Ceramic AA 50V Ceramic AA AC250V Ceramic AE 2kV Ceramic AC 160V Electrolytic AF 160V Electrolytic AE 16V Electrolytic AD 50V M.Polyester Film AB 6.3V Electrolytic AC 6.3V Electrolytic AD 50V Electrolytic AB 16V Electrolytic AC 50V Ceramic AA 50V Ceramic AA 50V Ceramic AA 50V Ceramic AA 16V Electrolytic AC 16V Ceramic AB 16V Ceramic AB 16V Electrolytic AC 50V M.Polyester Film AB 50V M.Polyester Film AB 50V Ceramic AA 50V Ceramic AA 6.3V Electrolytic AB 6.3V Electrolytic AB 16V Electrolytic AB 16V Ceramic AB 16V Ceramic AB 16V Electrolytic AB 50V Ceramic AA 50V Ceramic AA 6.3V Electrolytic AB 16V Ceramic AB 16V Ceramic AB 6.3V Electrolytic AB 16V Electrolytic AB 50V Mylar AB 50V Ceramic AA 50V Electrolytic AB 50V Mylar AB
14D1-S/G/W 14D2-S/G Ref. No.
★
Part No.
Description
Code
Ref. No.
RESISTORS RJ2 RJ9 RJ13 RJ14 RJ15 RJ16 RJ17 RJ18 RJ19 RJ24
VRN-MD2AL000J VRN-MD2AL000J VRN-MD2AL000J VRN-MD2AL000J VRN-MD2AL000J VRN-MD2AL000J VRN-MD2AL000J VRN-MD2AL000J VRN-MD2AL000J VRN-MD2AL000J
R R R R R R R R R R
0 0 0 0 0 0 0 0 0 0
RJ26 RJ28 RJ32 RJ33
VRN-MD2AL000J VRN-MD2AL000J VRN-MD2AL000J VRN-MD2AL000J
R R R R
0 0 0 0
RJ35 RJ37 RJ38 RJ41 RJ42 RJ43 RJ46 RJ47 RJ49 RJ50 RJ51 RJ52 RJ53 RJ56 RJ71 RJ73 RJ75 RJ76 RJ77 RJ78 RJ83 RJ88 R217 R230 R364 R366 RJ10 RJ21 R201 R202 R216 R219 R231 R232 R233 R234 R251 R252 R253 R254 R255 R256 R262 R263 R301 R302 R303 R304 R305 R310 R311 R313 R314 R315 R316 R318 R334 R335 R352
VRN-MD2AL000J VRN-MD2AL000J VRN-MD2AL000J VRN-MD2AL000J VRN-MD2AL000J VRN-MD2AL000J VRN-MD2AL000J VRN-MD2AL000J VRN-MD2AL000J VRN-MD2AL000J VRN-MD2AL000J VRN-MD2AL000J VRN-MD2AL000J VRN-MD2AL000J VRN-MD2AL000J VRN-MD2AL000J VRN-MD2AL000J VRN-MD2AL000J VRN-MD2AL000J VRN-MD2AL000J VRN-MD2AL000J VRN-MD2AL000J VRN-MD2AL000J VRN-MD2AL000J VRN-MD2AL000J VRN-MD2AL000J VRS-CY1JF000JY VRS-CY1JF000JY VRN-MD2AL101J VRN-MD2AL101J VRS-VV3LB223J VRD-RA2BE392JY VRD-RA2BE681JY VRN-MD2AL272J VRN-MD2AL102J VRN-MD2AL391J VRN-MD2AL181J VRN-MD2AL181J VRD-RA2BE680JY VRN-MD2AL560J VRN-MD2AL223J VRN-MD2AL223J VRN-MD2AL560J VRN-MD2AL560J VRN-MD2AL101J VRN-MD2AL101J VRN-MD2AL561J VRN-MD2AL100J VRN-MD2AL274J VRN-MD2AL473J VRN-MD2AL473J VRN-MD2AL102J VRN-MD2AL472J VRN-MD2AL272J VRN-MD2AL272J VRD-RA2BE680JY VRN-MD2AL332J VRS-CY1JF564JY VRN-MD2AL681J
R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R
0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 100 100 22k 3.9k 680 2.7k 1k 390 180 180 68 56 22k 22k 56 56 100 100 560 10 270k 47k 47k 1k 4.7k 2.7k 2.7k 68 3.3k 560k 680
1/10W Metal Film 1/10W Metal Film 1/10W Metal Film 1/10W Metal Film 1/10W Metal Film 1/10W Metal Film 1/10W Metal Film 1/10W Metal Film 1/10W Metal Film 1/10W Metal Film (14D2-S/G) 1/10W Metal Film 1/10W Metal Film 1/10W Metal Film 1/10W Metal Film (14D2-S/G) 1/10W Metal Film 1/10W Metal Film 1/10W Metal Film 1/10W Metal Film 1/10W Metal Film 1/10W Metal Film 1/10W Metal Film 1/10W Metal Film 1/10W Metal Film 1/10W Metal Film 1/10W Metal Film 1/10W Metal Film 1/10W Metal Film 1/10W Metal Film 1/10W Metal Film 1/10W Metal Film 1/10W Metal Film 1/10W Metal Film 1/10W Metal Film 1/10W Metal Film 1/10W Metal Film 1/10W Metal Film 1/10W Metal Film 1/10W Metal Film 1/10W Metal Film 1/10W Metal Film 1/16W Metal Oxide 1/16W Metal Oxide 1/10W Metal Film 1/10W Metal Film 3W Metal Oxide 1/8W Carbon 1/8W Carbon 1/10W Metal Film 1/10W Metal Film 1/10W Metal Film 1/10W Metal Film 1/10W Metal Film 1/8W Carbon 1/10W Metal Film 1/10W Metal Film 1/10W Metal Film 1/10W Metal Film 1/10W Metal Film 1/10W Metal Film 1/10W Metal Film 1/10W Metal Film 1/10W Metal Film 1/10W Metal Film 1/10W Metal Film 1/10W Metal Film 1/10W Metal Film 1/10W Metal Film 1/10W Metal Film 1/10W Metal Film 1/8W Carbon 1/10W Metal Film 1/16W Metal Oxide 1/10W Metal Film
AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AB AA AA AA AA AA AA AA AA AB AA AA AB AB AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA
★
R359 R360 R361 R431 R432 R458 R459 R501 R502 R503 R504 R505 R506 R507 R508 R509 R511 R512 R521 R529 R530 R531 R532 R533 R601 R602 R603 R604 R605 R606 R607 R609 R610 R611 R612 R613 R614 R615 R616 R618 R619 R620 R622 R623 R624 R625 R626 R633 R634 R641 R651 R652 R653 R654 R655 R656 R658 R663 R701 R707 R708 R709 R710
VRN-MD2AL102J R VRN-MD2AL103J R VRN-MD2AL104J R VRN-MD2AL101J R VRN-MD2AL820J R VRN-MD2AL103J R VRD-RA2BE680JY R VRD-RA2BE272JY R VRD-RM2HD102JY R VRN-VV3AB2R7J R VRN-MD2AL181J R VRN-MD2AL102J R VRS-VV3AB331J R VRN-VV3AB1R0J R VRD-RA2BE153JY R VRD-RA2BE153JY R VRN-MD2AL181J R VRD-RM2HD5R6JY R VRD-RA2BE333JY R VRD-RA2BE223JY R VRS-CY1JF334JY R VRN-MD2AL101J R VRN-MD2AL101J R VRD-RA2BE393JY R VRS-SV2HC102J R VRD-RA2BE393JY R VRD-RA2BE273JY R VRD-RA2BE563JY R VRD-RM2HD124JY R VRN-VV3AB1R5J R VRD-RM2HD270JY R VRD-RA2BE154JY R VRD-RA2BE102GY R VRN-MD2AL102J R VRN-MD2AL123J R VRN-MD2AL103J R VRS-SV2HC150J R VRS-VV3DB682J R VRN-VV3ABR47J R VRS-VV3DB391J R VRS-VV3LB103J R VRS-VV3AB472J R VRD-RA2BE102JY R VRD-RM2HD184JY R VRN-MD2AL472J R VRN-VV3DB8R2J R VRD-RM2HD470JY R VRD-RA2BE333JY R VRD-RA2BE103JY R VRN-SV2HCR47J R VRN-MD2AL223J R VRN-MD2AL102J R VRN-MD2AL822J R VRN-MD2AL273J R VRN-MD2AL391J R VRN-MD2AL100J R VRD-RA2BE101JY R VRD-RA2BE101JY R VRW-KQ3NC3R9K R VRS-VV3DB104J R VRD-RA2BE681JY R VRN-VV3DBR47J R VRN-VV3DBR56J R
R710
VRN-VV3DBR47J
R
VRD-RA2BE682JY VRD-RA2BE152JY VRD-RA2BE562JY VRC-UA2HG825KY VRC-UA2HG825KY VRD-RM2HD124JY VRD-RM2HD150JY VRD-RA2BE221JY VRD-RM2HD270JY VRN-MD2AL151J VRN-MD2AL221J
R R R R R R R R R R R
R711 R712 R716 å R751 å R752 R753 R754 R755 R756 R757 R801
41
Part No.
Description
Code
1k 1/10W Metal Film 10k 1/10W Metal Film 100k 1/10W Metal Film 100 1/10W Metal Film 82 1/10W Metal Film 10k 1/10W Metal Film 68 1/8W Carbon 2.7k 1/8W Carbon 1k 1/2W Carbon 2.7 1W Metal Film 180 1/10W Metal Film 1k 1/10W Metal Film 330 1W Metal Oxide 1 1W Metal Film 15k 1/8W Carbon 15k 1/8W Carbon 180 1/10W Metal Film 5.6 1/2W Carbon 33k 1/8W Carbon 22k 1/8W Carbon 330k 1/16W Metal Oxide 100 1/10W Metal Film 100 1/10W Metal Film 39k 1/8W Carbon 1k 1/2W Metal Oxide 39k 1/8W Carbon 27k 1/8W Carbon 56k 1/8W Carbon 120k 1/2W Carbon 1.5 1W Metal Film 27 1/2W Carbon 150k 1/8W Carbon 1k 1/8W Carbon 1k 1/10W Metal Film 12k 1/10W Metal Film 10k 1/10W Metal Film 15 1/2W Metal Oxide 6.8k 2W Metal Oxide 0.47 1W Metal Film 390 2W Metal Oxide 10k 3W Metal Oxide 4.7k 1W Metal Oxide 1k 1/8W Carbon 180k 1/2W Carbon 4.7k 1/10W Metal Film 8.2 2W Metal Film 47 1/2W Carbon 33k 1/8W Carbon 10k 1/8W Carbon 0.47 1/2W Metal Film 22k 1/10W Metal Film 1k 1/10W Metal Film 8.2k 1/10W Metal Film 27k 1/10W Metal Film 390 1/10W Metal Film 10 1/10W Metal Film 100 1/8W Carbon 100 1/8W Carbon 3.9 7W Cement 100k 2W Metal Oxide 680 1/8W Carbon 0.47 2W Metal Film 0.56 2W Metal Film (14D1-S/G/W) 0.47 2W Metal Film (14D2-S/G) 6.8k 1/8W Carbon 1.5k 1/8W Carbon 5.6k 1/8W Carbon 8.2M 1/2W Solid 8.2M 1/2W Solid 120k 1/2W Carbon 15 1/2W Carbon 220 1/8W Carbon 27 1/2W Carbon 150 1/10W Metal Film 220 1/10W Metal Film
AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AB AA AA AA AA AA AA AA AB AA AA AA AA AB AA AA AA AA AA AA AA AA AA AA AA AA AE AB AA AB AA AB AA AA AA AA AA AA AA AA AA AA AA
14D1-S/G/W 14D2-S/G Ref. No.
★
Part No.
R802 R803 R804 R805 R806 R807 R808 R809 R812 R813 R1001 R1002 R1003 R1004 R1005 R1011 R1012 R1013 R1014 R1015 R1016 R1017 R1019 R1020 R1021 R1022 R1023 R1024 R1025 R1026 R1028 R1030 R1031 R1032 R1034 R1035 R1036 R1037 R1038 R1039 R1040 R1041 R1042 R1046 R1048 R1050 R1051 R1072 R1073
VRN-MD2AL221J VRN-MD2AL221J VRN-MD2AL221J VRN-MD2AL822J VRN-MD2AL123J VRN-MD2AL103J VRN-MD2AL221J VRD-RA2BE224JY VRN-MD2AL101J VRN-MD2AL221J VRN-MD2AL221J VRN-MD2AL331J VRN-MD2AL471J VRN-MD2AL821J VRN-MD2AL181J VRN-MD2AL101J VRD-RA2BE271JY VRD-RA2BE101JY VRN-MD2AL101J VRN-MD2AL332J VRN-MD2AL101J VRN-MD2AL332J VRN-MD2AL392J VRN-MD2AL101J VRN-MD2AL153J VRN-MD2AL101J VRN-MD2AL101J VRN-MD2AL122J VRN-MD2AL101J VRN-MD2AL224J VRN-MD2AL101J VRN-MD2AL102J VRD-RA2BE562JY VRN-MD2AL332J VRN-MD2AL101J VRN-MD2AL332J VRN-MD2AL332J VRN-MD2AL101J VRN-MD2AL101J VRN-MD2AL223J VRN-MD2AL101J VRN-MD2AL101J VRD-RA2BE101JY VRN-MD2AL101J VRS-CY1JF102JY VRN-MD2AL392J VRN-MD2AL683J VRN-MD2AL101J VRN-MD2AL101J
å S702 S1001 S1002 S1003 S1004 S1005
QSW-P0591CEZZ QSW-K0003AJZZ+ QSW-K0003AJZZ+ QSW-K0003AJZZ+ QSW-K0003AJZZ+ QSW-K0003AJZZ+
R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R
Description 220 220 220 8.2k 12k 10k 220 220k 100 220 220 330 470 820 180 100 270 100 100 3.3k 100 3.3k 3.9k 100 15k 100 100 1.2k 100 220k 100 1k 5.6k 3.3k 100 3.3k 3.3k 100 100 22k 100 100 100 100 1k 3.9k 68k 100 100
1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/8W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/8W 1/8W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/8W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/8W 1/10W 1/16W 1/10W 1/10W 1/10W 1/10W
Code
Metal Film Metal Film Metal Film Metal Film Metal Film Metal Film Metal Film Carbon Metal Film Metal Film Metal Film Metal Film Metal Film Metal Film Metal Film Metal Film Carbon Carbon Metal Film Metal Film Metal Film Metal Film Metal Film Metal Film Metal Film Metal Film Metal Film Metal Film Metal Film Metal Film Metal Film Metal Film Carbon Metal Film Metal Film Metal Film Metal Film Metal Film Metal Film Metal Film Metal Film Metal Film Carbon Metal Film Metal Oxide Metal Film Metal Film Metal Film Metal Film
AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA
P302 P303 P303
Description
å P601 P602 P603 P701 å P702 P1001 P1002 RDA302
QPLGN0660CEZZ LHLDW1104PEZZ QPLGN0341CEZZ QPLGN0260CEZZ QPLGN0269GEZZ LHLDW1105PEZZ QPLGN0561CEZZ PRDAR0341PEFW
R R R R R R R R
Plug, 6pin(F) Holder(H) Plug, TP651-3 Plug, 2pin(M) Plug, 2pin(M) Holder(K) Plug, 5pin(BC) Heat Sink for IC302 (14D1-S/G/W) Heat Sink for IC302 (14D2-S/G) Heat Sink for IC501 Heat Sink for IC701 Remote Receiver Lug, Test Point Holder
PRDAR0118GJFW PRDARA028WJFW RRMCU0222CEZZ QLUGP0102PEZZ LHLDP1066PE00
R R R R R
Code AC AB AA AC AB AB AB AD AE AD AE AL AA AC
DUNTKB509WEA4(14D1-S/G) DUNTKB509WEA5(14D2-S/G) DUNTKB509WEA8(14D1-W) PWB-B:CRT UNIT TRANSISTORS Q870 Q871 Q872 Q883 Q885 Q887
RH-TX0110BMZZ+ RH-TX0110BMZZ+ RH-TX0110BMZZ+ RH-TX0124BMZZ+ RH-TX0124BMZZ+ RH-TX0124BMZZ+
R R R R R R
D881 D882 D883 D884 D885 D886 D887 D888
VHD1SS244//-1Y VHD1SS244//-1Y VHD1SS244//-1Y VHD1SS119//-1Y VHD1SS119//-1Y VHD1SS82///1AY VHD1SS82///1AY VHD1SS82///1AY
C871 C872 C873 C875 C876 C878 C880 C881 C882 C886
VCCCCY1HH471J R VCCCCY1HH391J R VCCCCY1HH471J R VCKYPA2HB102K+ R RC-KZ0150CEZZ R VCEA0A2EW106M+R VCCCCY1HH471J R VCKYPA1HB471K+ R VCKYPA1HB471K+ R VCKYPA2HB102K+ R
R879 R880 R881 R882 R883 R884 R885 R886 R887 R888 R892 R893 R894 R898 R899
VRN-MD2AL471J VRN-MD2AL471J VRN-MD2AL471J VRS-VV3DB153J VRD-RM2HD272JY VRS-VV3DB153J VRD-RM2HD272JY VRS-VV3DB153J VRD-RM2HD272JY VRN-MD2AL471J VRN-MD2AL102J VRN-MD2AL102J VRN-MD2AL102J VRN-MD2AL471J VRN-MD2AL471J
TX0110BM TX0110BM TX0110BM TX0124BM TX0124BM TX0124BM
AC AC AC AC AC AC
DIODES R R R R R R R R
1SS244 1SS244 1SS244 1SS119 1SS119 1SS82 1SS82 1SS82
AB AB AB AA AA AC AC AC
CAPACITORS
Switch AQ Switch, CH UP AB Switch, CH DOWN AB Switch, VOL UP AB Switch, VOL DOWN AB Switch, PICTURE/PRESET AB
AC Cord (14D1-W) AC Cord (except 14D1-W) Fuse, T3.15A/250V Ferrite Bead Fuse Holder Fuse Holder Jack, Video Jack, Audio Jack, AV-1 IN Plug, 2pin(S) (14D1-S/G/W) QPLGN0461CEZZ R Plug, 4pin(S) (14D2-S/G) QPLGN0461CEZZ R Plug, 4pin(HP) (14D1-S/G/W) QPLGN0561CEZZ R Plug, 5pin(HP) (14D2-S/G)
★
RDA501 RDA701 RMC1001 TP201
470p 390p 470p 1000p 1000p 10 470p 470p 470p 1000p
50V Ceramic 50V Ceramic 50V Ceramic 500V Ceramic 3.15kV Ceramic 250V Electrolytic 50V Ceramic 50V Ceramic 50V Ceramic 500V Ceramic
AA AA AA AA AB AD AA AA AA AA
RESISTORS
MISCELLANEOUS PARTS å ACC701 QACCB5003PEZZ R å ACC701 QACCZ2008PEZZ R å F701 QFS-C3229CEZZ R FB601 RBLN-0091GEZZY R å FH701 QFSHD1013CEZZ+ R å FH702 QFSHD1014CEZZ+ R J402 QJAKE0210CE04 R J403 QJAKE0210CE09 R J409 QJAKHA004WJZZ R P301 QPLGN0241CEZZ R
Part No.
RDA302 PRDAR0340PEFW R
SWITCHES R R R R R R
Ref. No.
AY AM AD AB AC AC AC AC AE AA
R R R R R R R R R R R R R R R
470 470 470 15k 2.7k 15k 2.7k 15k 2.7k 470 1k 1k 1k 470 470
1/10W 1/10W 1/10W 2W 1/2W 2W 1/2W 2W 1/2W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W
Metal Film Metal Film Metal Film Metal Oxide Carbon Metal Oxide Carbon Metal Oxide Carbon Metal Film Metal Film Metal Film Metal Film Metal Film Metal Film
AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA
AB
MISCELLANEOUS PARTS å SC881 P882 P884
AB AB
42
QSOCV0017PEZZ R Socket LHLDW1105PEZZ R Holder(K) LHLDW1104PEZZ R Holder(H)
AF AB AB
14D1-S/G/W 14D2-S/G Ref. No.
★
Part No.
Description
Code
Ref. No.
SP301 SP302
RESISTORS VRN-MD2AL000J VRN-MD2AL000J VRN-MD2AL000J VRN-MD2AL471J VRN-MD2AL471J
R R R R R
0 0 0 470 470
1/10W 1/10W 1/10W 1/10W 1/10W
Metal Film Metal Film Metal Film Metal Film Metal Film
AA AA AA AA AA
MISCELLANEOUS PARTS J351 P351
QJAKJ0101SEZZ R Headphone Jack QPLGN0461CEZZ R Plug, 4pin
★
Description
Code
MISCELLANEOUS PARTS
DUNTKB510WEA3 PWB-C HEADPHONE UNIT RJ60 RJ61 RJ62 R370 R371
Part No.
VSP9050PB35WA VSP9050PB35WA QCNW-2206PEZZ QCNW-2379PEZZ QCNW-2380PEZZ
R R R R R
Speaker Speaker(14D-2S/G) Connecting Cord Connecting Cord Connecting Cord (14D2-S/G) QCNW-2452PEZZ R Connecting Cord (14D2-S/G) QPLGJ0113CEZZ R Plug (except 14D1-W)
AK AK AD AE AG AE AG
AE AB
SUPPLIED ACCESSORIES ACCESSORIES RRMCG1342PESA R Infrared RC TINS-A340WJZZ R Operation Manual (14D1-S/G) TINS-A365WJZZ R Operation Manual (14D2-S/G) TINS-A425WJZZ R Operation Manual (14D1-W) QANTR0018PEZZ R Rod Antenna (except 14D1-W) TMAPCA013WJZZ R Map (14D2-S/G) TMAPCA014WJZZ R Map (14D1-S/G)
AU AK AK AF AQ AC AC
ACCESSORIE(NOT REPLACEMENT ITEM) TCAUA0002PEZZ
- Caution Card
—
PACKING PARTS (NOT REPLACEMENT ITEM) SPAKCA285WJZZ SPAKCA316WJZZ SPAKCA317WJZZ SPAKCA363WJZZ SPAKCA364WJZZ SPAKP0056PEZZ SPAKXA138WJZZ SPAKXA163WJZZ SSAKA0031PEZZ SSAKH0009PEZZ SSAKH0015PEZZ
43
- Packing Case (14D1-S) - Packing Case (14D2-S) - Packing Case (14D2-G) - Packing Case (14D1-G) - Packing Case (14D1-W) - Wrapping Paper (14D1-S/G/W) - Packing Foam (14D1-S/G/W) - Packing Foam (14D2-S/G) - Polyethylene Bag - Polyethylene Bag (14D1-S/G/W) - Polyethylene Bag (14D2-S/G)
— — — — — — — — — — —
14D1-S/G/W 14D2-S/G Ref. No.
Part No.
★
Description
Ref. No.
Code
Part No.
★
Description
CABINET PARTS LOCATION CABINET PARTS 14D1-S/G/W 1 1 1 1-1 1-2 1-3 1-4 1-5 1-6 2 2-1
CCABAA145WEV0 R Top Cabinet Ass'y (14D1-S) CCABAA178WEV0 R Top Cabinet Ass'y (14D1-G) CCABAA179WEV0 R Top Cabinet Ass'y (14D1-W) Not Available - Top Cabinet HBDGB0018PESB R SHARP Badge JBTN-A067WJSA R CTL Buton GCOVAA193WJSA R RC/LED Cover JBTN-A066WJSA R Power Button MSPRC0005PEFW R Power Button Spring CCABBA087WEV0 R Rear Cabinet Ass'y Not Available - Rear Cabinet
BC BC BC — AD AC AD AC AB AV —
14D2-S/G 1 1 1-1 1-2 1-3 1-3 1-4 1-5 1-5 1-6 2 2-1
CCABAA149WEV0 R Top Cabinet Ass'y (14D2-S) CCABAA151WEV0 R Top Cabinet Ass'y (14D2-G) Not Available - Top Cabinet HBDGB0019PESB R SHARP Badge JBTN-A028WJSA R CTL Buton (14D2-S) JBTN-A028WJSB R CTL Buton (14D2-G) GCOVAA106WJSA R LED/RC Cover JBTN-A069WJSA R Power Button (14D2-S) JBTN-A069WJSB R Power Button (14D2-G) MSPRC0068CEFW R Power Button Spring CCABBA096WEV0 R Rear Cabinet Ass'y Not Available - Rear Cabinet
BB BB — AD AF AF AC AD AD AA AX —
14D1-S/G/W
14D2-S/G
44
Code
14D1-S/G/W 14D2-S/G
PACKING OF THE SET ★ Polystyrene Bag ★ Buffer Material Operation Manual ★ Batteries ★ Wrapping Paper
Infrared Remote Control Unit
★ Buffer Material
★ Packing Case
★ Serial Number Card
Fix the packing case with 22 staples ★ Number Card
Mark ★ : Not Replacement Item
45
14D1-S/G/W 14D2-S/G Ref. No.
Part No.
★
Description
Ref. No.
Code
Part No.
★
Description
Code
COPYRIGHT © 2002 BY SHARP CORPORATION ALL RIGHTS RESERVED.
No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without prior written permission of the publisher.
TQ1431-S Nov. 2002 Printed in Japan In Japan gedruckt Design and Production Information Design : SEM Production : SREC
SHARP CORPORATION AV Systems Group Quality & Reliability Control Center Yaita, Tochigi 329-2193, Japan
MY. DS
46
