Transcript
TX-1 Handheld 3-Axis Gimbal for Smartphones & GoPro Cameras Q: The gimbal won't stabilise or hold my phone horizontally at all A: Ensure that the gimbal's battery grip has charge, and then repeat Step 2 of the Quick Start Guide. Also ensure that your Smartphone is fully inserted into the holder, or else the gimbal may have trouble achieving balance. Q: My Phone Won't fit the Clamp. A: Unfortunately the device mount is probably not compatible with your Smartphone. Please contact seller. Q: I can't see any picture on my Smartphone's screen. A: First ensure that your Smartphone's camera is switched on, and check that it is installed in the correct orientation. Please refer to Step 2 of the Quick Start Guide. Q: How long does tha battery last for? A: The battery normally lasts for approximately 3 hours.
For any other issues with the Gimbal, please contact the team at EssentialPhoto for Support.
PIXAPRO® LTD. 50 Popes Lane, Oldbury, West Midlands, B69 4PA
TX-1
Tel: 0845 872 7904 Web: www.essentialphoto.co.uk E-mail:
[email protected]
Company Registration No. 07601334
www.essentialphoto.co.uk
INTRODUCTION: Designed for use with Smartphones and GoPro cameras, the TX-1 hand held Gimbal Stabiliser from Vituso will give your pan, tilt and even walking shots professional fluid results. Unlike some other steady rigs, which can be complicated, and difficult to set up, the Vituso TX-1 comes pre-assembled, and it pretty much ready for use straight out of the box with minimal set up. Simply place your smartphone into the cradle with your lens to the left, then level the gimbal and turn on… The motors will level your camera out within a few seconds, and you’re ready to shoot. The TX-1 uses a unique 3-axis motorised Gyro system together with sophisticated software to counteract against sudden hand movements resulting in flawlessly stable, professional looking footage from your Smartphone. The TX-1 can also be used with the GoPro Hero 3 & 4 action cameras using the supplied GoPro mount accessory. Simply switch out the Smartphone cradle for the GoPro mount, and away you go. The GoPro mount encloses the camera, whilst still allowing for easy access to all of the controls.
SPECIFICATIONS: ● ● ● ● ● ●
3 Axis Active Stabilization (Pitch/Tilt, Roll and Pan). Gesture Control System Customised High Quality BLDC Motors Position & Rate Dual Closed-Loop Control System Maximum +/-0.1°Levelling Error Compatible with iPhones, Samsung Galaxy S Series or Smartphones with 5 inch screens.
● Plug & Play: No assembly Required ● Pre-Tuned Gimbal Control Boeard: No PID Tuning!
BOX CONTENT:
The TX-1 comes with a rechargeable battery pack, which lasts for approximately 3 hours, enabling you to take as much footage as your heard desires. The TX-1 is the Perfect solution for the video blogger or action videographer that is always on the go. Gimbal
Smartphone Clamps
Bag With Protective Foam
GoPro Cradle
Charger & Plugs
Battery Grip*
Counterweight
* Each Gimbal comes with one battery Grip. If you would like another one, please contact your dealer.
TILT/PITCH AXIS Slows down the rate of tilt / pitch to counteract sudden and quick tilting motions. To tilt the camera angle, simply tilt the gimbal forward (away from you) or backward (towards you).
Control Board Inside The Box ROLL AXIS Stabilises the Smartphone by counteracting against side to side movements of the handle.
PAN AXIS
Slows the rate of panning / turning to counteract sudden or quick turnng motions. This enables smooth / controlled camera turning motions. Simply twist your gimbal left and right to see how this works
TIPS Spend some time to observe the behaviour of the gimbal in order to familiarise yourself with its characterestics. Please switch off your gimbal before removing your phone otherwise the gimbal wil vibrate. The Gimbal is protected by Low-Voltage Cutoff mechanisms. If your gimbal is low on battery, it will not stabilise. Please recharge your battery.
STEP 1 Slide your Smartphone in Keep it balanced along the "Pitch" axis.
Expandable Clamp
STEP 2 Adjust the counterweight balance along the "Roll" axis.
Changing Battery When the Red Light blinks, please change the battery.
STEP 3 k!
Clic The RED light on the charger inicates "Charging". GREEN light indicates fuly charged.
Press the power button. This will enble the gimbal and the motors, to keep the smart phone stabilised. The gibal is now ready for use. Press it again to turn the gimbal off. Note: Don't Turn n the power before sliding the smart phone.
