Transcript
TESTING
2 A CAPACITY RELAY WITH HIGH SURGE VOLTAGE & HIGH BREAKDOWN VOLTAGE 15 .591
7.4 .291 8.2 .323
15 .591
7.4 .291 8.4 .331
mm inch
TX RELAYS
FEATURES • Breakdown voltage between contacts and coil: 2,000 V • Surge withstand between contacts and coil: 2,500 V • High contact capacity: 2 A 30 V DC • Surface-mount type available
SPECIFICATIONS Contact
Characteristics
Arrangement Initial contact resistance, max. (By voltage drop 6 V DC 1 A) Contact material Nominal switching capacity (resistive load) Max. switching power (resistive load) Rating Max. switching voltage Max. switching current Min. switching capacity ❇1 Nominal operating power
Single side stable
Expected life (min. operations)
2 A 30 V DC resistive Electrical (at 20 cpm) 1 A 30 V DC resistive
1 coil latching 2 coil latching Mechanical (at 180 cpm)
2 Form C 100 mΩ Gold-clad silver alloy 2 A 30 V DC 60 W 220 V DC 2A 10 µA 10 mV DC 140 mW (1.5 to 24 V DC) 270 mW (48 V DC) 100 mW (1.5 to 24 V DC) 200 mW (1.5 to 24 V DC) 108 105 5×105
Notes: ❇1This value can change due to the switching frequency, environmental conditions, and desired reliability level, therefore it is recommended to check this with the actual load. (SX relays are available for low level load switching [10 µA 1 mV DC – 10 mA 10 V DC]) ❇2The upper limit for the ambient temperature is the maximum temperature that can satisfy the coil temperature rise. Under the packing condition, allowable temperature range is from –40 to +70°C –40°C to +158°F.
Remarks * Specifications will vary with foreign standards certification ratings. *1 Measurement at same location as "Initial breakdown voltage" section. *2 By resistive method, nominal voltage applied to the coil; contact carrying current: 2 A. *3 Nominal voltage applied to the coil, excluding contact bounce time. 4 * Nominal voltage applied to the coil, excluding contact bounce time without diode. *5 Half-wave pulse of sine wave: 6 ms; detection time: 10 µs. *6 Half-wave pulse of sine wave: 6 ms. *7 Detection time: 10 µs. *8 Refer to 6. Conditions for operation, transport and storage mentioned in AMBIENT ENVIRONMENT.
Initial insulation resistance*1 Between open contacts Initial breakdown Between contact sets voltage Between contact and coil Between open contacts Initial surge (10×160 µs) voltage Between contacts and coil (2×10 µs) Temperature rise*2 (at 20°C)
Min. 1,000 MΩ (at 500 V DC) 1,000 Vrms for 1 min. (Detection current: 10 mA) 1,000 Vrms for 1 min. (Detection current: 10 mA) 2,000 Vrms for 1 min. (Detection current: 10 mA) 1,500 V (FCC Part 68) 2,500 V (Telcordia) Max. 50°C
Max. 4 ms (Approx. 2 ms) Operate time [Set time]*3 (at 20°C) [Max. 4 ms (Approx. 2 ms)] Max. 4 ms (Approx. 1 ms) Release time [Reset time]*4 (at 20°C) [Max. 4 ms (Approx. 2 ms)] Min. 750 m/s2 {75 G} Functional*5 Shock resistance Destructive*6 Min. 1,000 m/s2 {100 G} 196 m/s2 {20 G}, 10 to 55 Hz Functional*7 at double amplitude of 3.3 mm Vibration resistance 294 m/s2 {30G}, 10 to 55 Hz Destructive at double amplitude of 5 mm –40°C to +85°C (up to 24 V coil) Conditions for operation, transport and Ambient tem- –40°F to +185°F (up to 24 V coil) perature ❇2 –40°C to +70°C (48 V coil) storage*8 (Not freezing and –40°F to +158°F (48 V coil) condensing at low Humidity 5 to 85% R.H. temperature) Unit weight Approx. 2 g .071 oz
All Rights Reserved © COPYRIGHT Matsushita Electric Works, Ltd.
TX ORDERING INFORMATION Ex. TX Contact arrangement
2
SA
Surface-mount availability
–
L
–
H
–
Operating function Terminal shape
Nil: Standard PC board terminal type or Nil: self-clinching terminal type SA: Standard surface-mount terminal type SL : High connection reliability surface-mount SL : terminal type SS: Space saving surface-mount terminal type
–
3V
Z
Coil voltage (DC)
Packing style
Nil: Standard PC 1.5, 3, 4.5, 5, 6, Nil: Tube packing board terminal or 9, 12, 24, 48* V Z: Tape and reel surface-mount packing(picked terminal from the 8/9/10/12 H: Self-clinching -pin side terminal Notes: 1. Tape and reel (picked from 1/3/4/5-pin side) is also available by request. Part number suffix “-X” is *48 V coil type: Single side stable only 2: 2 Form C
Nil: Single side Nil: stable L: 1 coil latching L2: 2 coil latching
needed when ordering. (ex.) TX2SA-3 V-X 2. Tape and reel packing symbol “-Z” or “-X” are not marked on the relay.
TYPES AND COIL DATA (at 20°C 68°F) 1) Standard PC board terminal type and self-clinching terminal type 1. Single side stable Part No. Standard PC board terminal TX2-1.5 V TX2-3 V TX2-4.5 V TX2-5 V TX2-6 V TX2-9 V TX2-12 V TX2-24 V TX2-48 V
Nominal voltage, V DC
Pick-up voltage, V DC (max.)
Drop-out voltage, V DC (min.)
1.5 3 4.5 5 6 9 12 24 48
1.13 2.25 3.38 3.75 4.5 6.75 9 18 36
0.15 0.3 0.45 0.5 0.6 0.9 1.2 2.4 4.8
Nominal voltage, V DC
Set voltage, V DC (max.)
Reset voltage, V DC (max.)
1.5 3 4.5 5 6 9 12 24
1.13 2.25 3.38 3.75 4.5 6.75 9 18
1.13 2.25 3.38 3.75 4.5 6.75 9 18
Self-clinching terminal
Nominal voltage, V DC
Set voltage, V DC (max.)
Reset voltage, V DC (max.)
TX2-L2-H-1.5 V TX2-L2-H-3 V TX2-L2-H-4.5 V TX2-L2-H-5 V TX2-L2-H-6 V TX2-L2-H-9 V TX2-L2-H-12 V TX2-L2-H-24 V
1.5 3 4.5 5 6 9 12 24
1.13 2.25 3.38 3.75 4.5 6.75 9 18
1.13 2.25 3.38 3.75 4.5 6.75 9 18
Self-clinching terminal TX2-H-1.5 V TX2-H-3 V TX2-H-4.5 V TX2-H-5 V TX2-H-6 V TX2-H-9 V TX2-H-12 V TX2-H-24 V TX2-H-48 V
Nominal operating current, mA (±10%) 93.8 46.7 31 28.1 23.3 15.5 11.7 5.8 5.6
Coil resistance, Ω (±10%) 16 64.3 145 178 257 579 1,028 4,114 8,533
Nominal operating power, mW 140 140 140 140 140 140 140 140 270
Max. allowable voltage, V DC 2.2 4.5 6.7 7.5 9 13.5 18 36 57.6
Nominal operating power, mW 100 100 100 100 100 100 100 100
Max. allowable voltage, V DC 2.2 4.5 6.7 7.5 9 13.5 18 36
Nominal operating power, mW 200 200 200 200 200 200 200 200
Max. allowable voltage, V DC 2.2 4.5 6.7 7.5 9 13.5 18 36
2. 1 Coil latching Part No. Standard PC board terminal TX2-L-1.5 V TX2-L-3 V TX2-L-4.5 V TX2-L-5 V TX2-L-6 V TX2-L-9 V TX2-L-12 V TX2-L-24 V
Self-clinching terminal TX2-L-H-1.5 V TX2-L-H-3 V TX2-L-H-4.5 V TX2-L-H-5 V TX2-L-H-6 V TX2-L-H-9 V TX2-L-H-12 V TX2-L-H-24 V
Nominal operating current, mA (±10%) 66.7 33.3 22.2 20 16.7 11.1 8.3 4.2
Coil resistance, Ω (±10%) 22.5 90 202.5 250 360 810 1,440 5,760
3. 2 Coil latching Part No. Standard PC board terminal TX2-L2-1.5 V TX2-L2-3 V TX2-L2-4.5 V TX2-L2-5 V TX2-L2-6 V TX2-L2-9 V TX2-L2-12 V TX2-L2-24 V Notes:
1. Specified value of pick-up, drop-out, set and reset voltage is with the condition of square wave coil pulse.
Nominal operating current, mA (±10%) 133.9 66.7 44.5 40 33.3 22.2 16.7 8.3
Coil resistance, Ω (±10%) 11.2 45 101.2 125 180 405 720 2,880
2. Standard packing: Tube: 40 pcs.; Case: 1,000 pcs. 3. In case of 5 V transistor drive circuit, it is recommended to use 4.5 V type relay.
All Rights Reserved © COPYRIGHT Matsushita Electric Works, Ltd.
TX 2) Surface-mount terminal type 1. Single side stable Part No. TX2S❍-1.5 V TX2S❍-3 V TX2S❍-4.5 V TX2S❍-5 V TX2S❍-6 V TX2S❍-9 V TX2S❍-12 V TX2S❍-24 V TX2S❍-48 V
Nominal voltage, V DC
Pick-up voltage, V DC (max.)
Drop-out voltage, V DC (min.)
1.5 3 4.5 5 6 9 12 24 48
1.13 2.25 3.38 3.75 4.5 6.75 9 18 36
0.15 0.3 0.45 0.5 0.6 0.9 1.2 2.4 4.8
Nominal voltage, V DC
Set voltage, V DC (max.)
Reset voltage, V DC (max.)
1.5 3 4.5 5 6 9 12 24
1.13 2.25 3.38 3.75 4.5 6.75 9 18
Nominal voltage, V DC 1.5 3 4.5 5 6 9 12 24
Nominal operating current, mA (±10%) 93.8 46.7 31 28.1 23.3 15.5 11.7 5.8 5.6
Coil resistance, Ω (±10%)
Nominal operating power, mW
Max. allowable voltage, V DC
16 64.3 145 178 257 579 1,028 4,114 8,533
140 140 140 140 140 140 140 140 270
2.2 4.5 6.7 7.5 9 13.5 18 36 57.6
Nominal operating current, mA (±10%)
Coil resistance, Ω (±10%)
Nominal operating power, mW
Max. allowable voltage, V DC
1.13 2.25 3.38 3.75 4.5 6.75 9 18
66.7 33.3 22.2 20 16.7 11.1 8.3 4.2
22.5 90 202.5 250 360 810 1,440 5,760
100 100 100 100 100 100 100 100
2.2 4.5 6.7 7.5 9 13.5 18 36
Set voltage, V DC (max.)
Reset voltage, V DC (max.)
Nominal operating current, mA (±10%)
Coil resistance, Ω (±10%)
Nominal operating power, mW
Max. allowable voltage, V DC
1.13 2.25 3.38 3.75 4.5 6.75 9 18
1.13 2.25 3.38 3.75 4.5 6.75 9 18
133.9 66.7 44.5 40 33.3 22.2 16.7 8.3
11.2 45 101.2 125 180 405 720 2,880
200 200 200 200 200 200 200 200
2.2 4.5 6.7 7.5 9 13.5 18 36
2. 1 coil latching Part No. TX2S❍-L-1.5 V TX2S❍-L-3 V TX2S❍-L-4.5 V TX2S❍-L-5 V TX2S❍-L-6 V TX2S❍-L-9 V TX2S❍-L-12 V TX2S❍-L-24 V
3. 2 coil latching Part No. TX2S❍-L2-1.5 V TX2S❍-L2-3 V TX2S❍-L2-4.5 V TX2S❍-L2-5 V TX2S❍-L2-6 V TX2S❍-L2-9 V TX2S❍-L2-12 V TX2S❍-L2-24 V
❍: For each surface-mounted terminal variation, input the following letter. SA type: A , SL type: L , SS type: S
Notes: 1. Specified value of pick-up, drop-out, set and reset voltage is with the condition of square wave coil pulse. 2. Standard packing: Tube: 40 pcs.; Case: 1,000 pcs. 3. Tape and reel packing is also available for surface-mount type by request. Part number suffix "-X" or "-Z" is needed when ordering. In this case, "X" or "Z" are not marked on the relay. Quantity in tape and reel: 500 pcs. • TX2SA-L-3V-Z (ex.) • TX2SA-3V-X Picked from the 1/3/4/5-pin side Picked from the 8/9/10/12-pin side 4. In case of 5 V transistor drive circuit, it is recommended to use 4.5 V type relay.
All Rights Reserved © COPYRIGHT Matsushita Electric Works, Ltd.
TX DIMENSIONS
mm inch
1. Single side stable and 1 coil latching type 15 Standard PC board terminal .591
PC board pattern (Copper-side view)
7.4 .291
0.65 8.2 .026 .323
0.5 .020 1.15 .045
Self clinching terminal
2.54 .100
3.5 .138 5.08 .200
5.08 .200
2.54 .100
Schematic (Bottom view) Single side stable 1 coil latching (Deenergized condition) (Reset condition)
10.16 .400
+
0.25 .010
5.08 .200
–
8-1.0 dia 8-.039 dia
15 .591
7.4 .291
1
3 4 5
12
10 9 8
– +
Direction indication*
Tolerance: ±0.1 ±.004
1
3 4 5
12
10 9 8
Direction indication*
*Orientation stripe located on top of relay.
0.65 8.2 .026 .323
0.5 .020 1.15 .045
3.5 .138 5.08 .200
5.08 .200
2.54 .100
0.25 .010
General tolerance: ±0.3 ±.012
Surface-mount terminal SA type
1 5.08 .039 .200
15 .591
7.4 .291 8.2 .323
0.5 .020 5.08 .200
0.65 2.54 .026 .100
0.5 .020 5.08 .200
SS type
5.08 .200
1 5.08 .039 .200
Max. 10.0 .390 5.08 .200
Self clinching terminal
3 4 5
12
10 9 8
1
3 4 5
–
+ Direction indication
Direction indication
2.54 .100
6.24 .246
0.25 .010
7.4±0.5 .291±.020
15 .591
Tolerance: ±0.1 ±.004 PC board pattern (Copper side view)
7.4 .291
12.7 .500
2.54 .100
3.5 .138 5.08 .200
1
+
2.54 .100
2.16 .085
0.65 8.2 .026 .323
0.5 .020 1.15 .045
10 9 8
7.24 .285
7.4 .291
0.65 2.54 .026 .100
12
3.16 .124
General tolerance: ±0.3 ±.012
2. Coil latching type Standard PC board terminal
For glue-pad
15 .591
5.08 0.25 .200 9.4±0.5 .010 .370±.020
8.2 .323 0.5 .020
0.3 .012
1 5.08 .039 .200
Max. 10.0 .390
15 .591
–
7.24 .285
7.4 .291
0.65 2.54 .026 .100
Schematic (Top view) Single side stable 1 coil latching (Deenergized condition) (Reset condition)
1.6 .0.63
3.16 .124
5.08 .200 0.25 9.4±0.5 .010 .370±.020
8.2 .323
2.54 .100
8.4 .331
15 .591
SL type
Suggested mounting pad (Top view)
5.08 .200
2.54 .100
15 .591
5.08 .200
0.25 .010 10-1.0 dia 10-.039 dia
7.4 .291
Schematic (Bottom view) 2 coil latching (Reset condition) 1
3 4 5 6
+
–
+
–
12
10 9 8 7
Direction indication*
Tolerance: ±0.1 ±.004
0.65 8.2 .026 .323
0.5 .020 1.15 .045
3.5 .138 5.08 .200
5.08 .200
2.54 .100
0.25 .010
General tolerance: ±0.3 ±.012
Surface-mount terminal SA type
Suggested mounting pad (Top view) 15 .591 8.2 .323 0.5 .020 5.08 .200
5.08 .200 0.25 9.4±0.5 .010 .370±.020
0.65 2.54 .026 .100
0.5 .020 5.08 .200
SS type
0.65 2.54 .026 .100
For glue-pad
2.54 .100
3.16 .124 7.24 .285
7.4 .291 8.2 .323
5.08 .200
15 .591
5.08 0.25 .200 9.4±0.5 .010 .370±.020
0.65 2.54 .026 .100
1 5.08 .039 .200
Max. 10.0 .390
2.54 .100
2.16 .085 5.08 .200
6.24 .285 0.25 .010
7.4±0.5 .291±.020
General tolerance: ±0.3 ±.012
Schematic (Top view) 2 coil latching (Reset condition) 12
Tolerance: ±0.1 ±.004
All Rights Reserved © COPYRIGHT Matsushita Electric Works, Ltd.
10 9 8
+ + 1
0.3 .012 1 5.08 .039 .200
Max. 10.0 .390
15 .591
0.5 .020
1.6 .0.63 7.24 .285
7.4 .291 8.2 .323
2.54 .100
3.16 .124
8.4 .331
15 .591
SL type
1 5.08 .039 .200
7.4 .291
7
– – 3
4 5
Direction indication
6
TX REFERENCE DATA 1. Maximum switching capacity
2. Life curve
3. Mechanical life
Ratio against the rated voltage, %V
Tested sample: TX2-5V, 10 pcs. Operating frequency: 180 cpm 3.0 100 No. of operations ×104
Switching current, A
2.0 DC resistive load
1.0
0.5 0.4 0.3
50 30V DC resistive load
30 20 10
0.2
100 90 80
Pick-up voltage
70
Max.
60
Min.
50 40 30
Drop-out voltage
20
Max. Min.
10 0
20 30
0
50 100 200 300 Contact voltage, V
0
1.0 2.0 Switching current, A
10
100 1,000 No. of operations, ×104
10,000
4. Electrical life
5-(1). Coil temperature rise
Tested sample: TX2-5V, 6 pcs. Operating frequency: 20 cpm
Tested sample: TX2-5V, 6 pcs. Point measured: Inside the coil Ambient temperature: 25°C 77°F, 85°C 185°F
Change of contact resistance 100
90
90
80
Pick-up voltage
70
Max.
60
Min.
50 40
Drop-out voltage
Max.
30 20
70
80 70 60 50 40
Max.
30
Min.
+25°C +77°F +85°C +185°F
60 50 40 30
2A 2A
20
0A 0A
20 Min.
0
1
2
3
4 5 6 7 8 9 No. of operations, ×104
10
10 0
10
1
2
3
4 5 6 7 8 9 4 No. of operations, ×10
5-(2). Coil temperature rise
6-(1). Operate and release time (with diode)
Tested sample: TX2-48V, 6 pcs. Point measured: Inside the coil Ambient temperature: 25°C 77°F, 70°C 158°F
Tested sample: TX2-5V, 10 pcs.
+25°C +77°F +70°C +158°F
60 50
2A
40
2A 0A
30
0A
20
0
4
Max.
3
Min.
2
Max. Min.
0
100 110 120 130 140 150 No. of operations, ×104
120 130 140 150 No. of operate, ×104
5 Operate time Release time
1
10
100 110
6-(2). Operate and release time (without diode)
5 Operate and release time, ms
70
0
10
Operate and release time, ms
10
Temperature rise, °C
Temperature rise, °C
100
Contact resistance, mΩ
Ratio against the rated voltage, %V
Change of pick-up and drop-out voltage
Operate time Release time
4
Max. Min.
3
2 Max. Min. 1
70
80
90 100 110 120 Coil applied voltage, %V
0
70
80
90 100 110 120 Coil applied voltage, %V
8. Distribution of set and reset voltage
9. Ambient temperature characteristics
Tested sample: TX2-5V, 50 pcs.
Tested sample: TX2-L2-12V, 30 pcs.
Tested sample: TX2-5V, 5 pcs.
10
0
0
10 20 30 40 50 60 70 80 90 100 Ratio against the rated voltage, %V
Rate of change, %
Quantity
Drop-out voltage 20
Set voltage Reset voltage
15
Pick-up voltage
;;;;;;; ;;;;;;
Quantity
30
; ; ; ; ;;;;;;;;;; ;;;;;
7. Distribution of pick-up and drop-out voltage
10 –40 –20 5
0
40
20
Pick-up voltage 20 40 60 80 Ambient temperature, °C –20
–40 0
0
10 20 30 40 50 60 70 80 90 100 Ratio against the rated voltage, %V
All Rights Reserved © COPYRIGHT Matsushita Electric Works, Ltd.
Drop-out voltage x x
TX 10. Distribution of contact resistance
11-(1). High frequency characteristics
11-(2). High frequency characteristics
Tested sample: TX2-5V, 30 pcs. (30 × 4 contacts)
Tested sample: TX2-12V, 2 pcs. Isolation characteristics
Tested sample: TX2-12V, 2 pcs. Insertion loss characteristics
1
3 4 5
12
10 9 8
20
15 10 5
0 20
Terminal Nos. 3-4, 9-10
100
50
0.4 0.2 10
30 40 50 Contact resistance, mΩ
100 Frequency, MHz
1,000
12-(2). Malfunctional shock (latching)
Tested sample: TX2-5V, 6 pcs
Tested sample: TX2-L2-12V, 6 pcs.
Z XX'
Y 1000m/s 2
Deenergized condition Energized condition
Z' Y Y'
Z XX'
X 1000m/s2
Z 1000m/s2
1000m/s 2 Z'
1000m/s2 X'
1000m/s 2 Z'
1000m/s2 X'
0 –5
ON
OFF OFF Drop-out voltage
–5
OFF 2 4 6 8 10 .079 .157 .236 .315 .394 Inter-relay distance
1,000
13-(3). Influence of adjacent mounting
Rate of change, %
Rate of change, %
ON
Rate of change, %
Rate of change, % Rate of change, %
ON
13-(2). Influence of adjacent mounting
Pick-up voltage
0
100 Frequency, MHz
1000m/s 2 Y'
13-(1). Influence of adjacent mounting
5
10
Reset state Set state
Z 1000m/s2
1000m/s 2 Y'
0
Y 1000m/s 2
X 1000m/s2
5
0.8 0.6
12-(1). Malfunctional shock (single side stable)
Z' Y Y'
1.0
ON
5 Pick-up voltage 0
ON
–5
ON
Rate of change, %
0
Insertion loss, dB
25
(BOTTOM VIEW) Isolation, dB
Quantity
30
;;;;;;; ; ;;;;;;;;;
;;;;;;;;;; ; ;;;;;;;;
35 Terminal Nos. 4-5, 8-9
OFF
5 Drop-out voltage 0
OFF –5 OFF 0
, mm inch
2 4 6 8 10 .079 .157 .236 .315 .394 Inter-relay distance
5 Pick-up voltage
ON
0
ON
–5
ON ON
5 0
OFF Drop-out voltage OFF
–5
OFF OFF 0
, mm inch
2 4 6 8 10 .079 .157 .236 .315 .394 Inter-relay distance
, mm inch
14. Pulse dialing test
Circuit
+
458 Ω
0.08 µF 48V DC
–
0.08 µF
458 Ω Wire spring relay
4 3
Ratio against the rated voltage, %V
Change of pick-up and drop-out voltage
Change of contact resistance 100
100
90
90 80
Pick-up voltage
70
Max. Min.
60 50 40 Drop-out voltage
30 20
Contact resistance, mΩ
Tested sample: TX2-5V, 6 pcs. (35 mA 48 V DC wire spring relay load)
Max. Min.
70 60 50
Max.
40 Min.
30 20 10
10 0
80
10
20 30 40 4 No. of operation, ×10
50
Note: Data of surface-mount type are the same as those of PC board terminal type.
All Rights Reserved © COPYRIGHT Matsushita Electric Works, Ltd.
0
10
20 30 40 No. of operations, ×104
50
TX Notes 1. Packing style 1) The relay is packed in a tube with the relay orientation mark on the left side, as shown in the figure below.
2) Tape and reel packing (surface-mount terminal type) (1) Tape dimensions (i) SA type
(2) Dimensions of plastic reel mm inch 21 ±0.6 dia. .827 ±.024 dia.
mm inch 2.0 ±0.5 .079 ±.020
Orientation (indicates PIN No.1)stripe +0.1 0 dia. Relay polarity bar 1.5 +.004 .059 0 dia. 2.0 (Z type) .079
1.75 .069
4.0 .157
0.4 .016
100 ±1 dia. 3.937 ±.039 dia.
C A
Stopper (gray)
Stopper (green)
B
11.5 .453
D 16.0 10.0 .394 .630
TX/TX-D/TX-S -SMD relays
15.5 .610
24.0 ±0.3 ±0.2 .945 ±.012 9.2±.008 .362
Tape coming out direction
(ii) SL type mm inch +0.1 0 dia. Relay polarity bar 1.5 +.004 .059 0 dia. 2.0 (Z type) .079
1.75 .069
4.0 .157
0.4 .016
11.5 .453 15.5 .610
TX/TX-D/TX-S -SMD relays
16.0 .630
10.0 .394 Tape coming out direction
24.0 ±0.3 .945 ±.012
10.8±0.2 .425±.008
(iii) SS type mm inch +0.1 0 dia. Relay polarity bar 1.5 +.004 .059 0 dia. 2.0 (Z type) .079
2.2 dia. .087 dia. 4.0 1.75 .157 .069
0.4 .016
11.5 .453 15.5 .610
TX/TX-D/TX-S -SMD relays
16.0 .630 Tape coming out direction
8.0 24.0 ±0.3 ±.012 .315 .945 10.8±0.2 .425±.008
For Cautions for Use, see Relay Technical Information.
All Rights Reserved © COPYRIGHT Matsushita Electric Works, Ltd.
370 ±2 dia. 14.567 ±.079 dia. ±0.5
13 dia. .512 ±.020 dia. 24.4+20 .961+.079 0
2.0±0.2 .079±.008
