Preview only show first 10 pages with watermark. For full document please download

Tx-sr804

   EMBED


Share

Transcript

TX-SR804_DIG.fm Page 1 Friday, September 8, 2006 1:22 PM TX-SR804 Quick Guide This guide shows how to get your AV receiver up and running quickly and smoothly. It shows you how to connect your speakers, DVD player, and TV, and how to use Automatic Speaker Setup. For full details on using the AV receiver, refer to the main instruction manual. Home Theater Basics ❍ Where to Put Your Speakers Front speakers Surround back speakers Subwoofer Center speaker Surround speakers ❍ Audio & Video Signal Flow 1 Speakers : Signal Flow Audio 2 Video Video 4 3 Audio 5 Audio DVD player TV Connections 1 through 5 are explained on the following pages. 1 En TX-SR804_DIG.fm Page 2 Friday, September 8, 2006 1:22 PM System Hookup 1 Connecting Your Speakers The AV receiver’s positive (+) speaker terminals are color-coded for easy identification. (The negative (–) speaker terminals are all black.) Speaker terminal Color Front left White Front right Red Center Green Surround left Blue Surround right Gray Surround back left Brown Surround back right Tan The supplied speaker labels are also color-coded and you should attach them to the positive (+) side of each speaker cable in accordance with the above table. All you need to do then is to match the color of each label to the corresponding speaker terminal. Connecting a Powered Subwoofer Using a suitable cable, connect the AV receiver’s SUBWOOFER PRE OUT to an input on your powered subwoofer, as shown. If your subwoofer is unpowered and you’re using an external amplifier, connect the SUBWOOFER PRE OUT to an input on the amp. Note: Make sure the plug is pushed in all the way. Powered subwoofer LINE INPUT LINE INPUT Connecting Speakers Front right speaker 1 Front left speaker Unscrew the terminal. Center speaker 2 Fully insert the bare wire, making sure that it’s touching the center of the terminal. 3 Screw the terminal tight. Surround back right speaker 2 Surround back left speaker Surround right speaker Surround left speaker TX-SR804_DIG.fm Page 3 Friday, September 8, 2006 1:22 PM 2+3 Basic DVD Player Hookup VIDEO OUT L DVD player R AUDIO OUT 2 COAXIAL OUT DVD IN V 3 DIGITAL COA- IN1 XIAL 3 FRONT L R DVD Connection AV receiver 2 3 3 DVD IN V Signal flow Composite video output DVD player DVD IN FRONT Analog audio L/R output DIGITAL COAXIAL IN 1 Digital coaxial output Note: The digital connection 3 offers Dolby & DTS listening modes, the analog connection 3 allows you to listen in Zone 2. 4+5 Basic TV Hookup L R 5 TV AUDIO OUT VIDEO IN 4 IN L R MONITOR OUT V VIDEO 3 Connection AV receiver 4 5 MONITOR OUT V Signal flow Composite video input TV VIDEO 3 IN L/R Analog audio L/R output Note: Connection 5 is only necessary if you want to listen to TV programs through the AV receiver. Connect the Power cord and start the Automatic Speaker Setup. ➔ See page 4. 3 TX-SR804_DIG.fm Page 4 Friday, September 8, 2006 1:22 PM Turning on & Using Automatic Speaker Setup With the supplied speaker setup microphone, use the Automatic Speaker Setup function. Before using this function, connect and position all your speakers. Remote controller 1 AV receiver RECEIVER STANDBY/ON or Press the [STANDBY/ON] button on the AV receiver or press the remote controller’s [RECEIVER] button followed by the [ON] button to turn on the AV receiver. Turn on the TV and select the input to which the AV receiver is connected. ON 2 MIC position SETUP MIC Put the speaker setup microphone in the listening position, and connect it to the SETUP MIC jack on the front panel. And press [ENTER]. The automatic speaker setup starts. The whole process takes about 2 minutes. ENTER Auto Speaker Setup -----------------------Push Enter:Start Caution! Loud sound. 3 When you’ve finished the setup, press the Up and Down [ ]/[ ] buttons to select “Apply the Results,” and then press [ENTER]. Auto Speaker Setup -----------------------Apply the Results ENTER ENTER Check the Results Retry Retry with Test noise Level up Disconnect the speaker setup microphone. Cancel Selecting the Input Source 1. Use the AV receiver’s input selector buttons to select the input source. To select the input source with the remote controller, press the [RECEIVER] button, and then use the INPUT SELECTOR buttons. 3 MASTER VOLUME STANDBY/ON STANDBY ZONE 2 PURE AUDIO 2. Start playback. 3. To adjust the volume, use the MASTER VOLUME control, or the remote controller’s [VOL] button. MULTI CH DVD VIDEO 1 VIDEO 2 VIDEO 3 VIDEO 4 TAPE TUNER CD PHONO DISPLAY PUSH TO OPEN 1 I0609-1 SN 29344330 (C) Copyright 2006 ONKYO CORPORATION Japan. All rights reserved. * 2 9 3 4 4 3 3 0 *